Professional Documents
Culture Documents
STEP BY STEP INSTRUCTIONS CoolSat 4000
STEP BY STEP INSTRUCTIONS CoolSat 4000
Every step required to use your CoolSat Receiver with this IKS provider is explained in
detail. The entire setup process is quite simple and should take less then 1 hour from start to
finish. If you wish to begin viewing TV in the shortest possible time it is imperative that
you carefully follow the instructions in this guide. Do not deviate nor skip any of the steps.
down menu and change them to those values. STEP 4. EDIT THE
RQ-SSSP-CLIENT.CONF FILE The following info must be edited into your
rq-sssp-client.conf file. 1. COM PORT # if it is other than "1" 2. Your 14 digit
ACCESS CODE. 3. The SERVER (62.212.88.227 for 1.nfps.ws) or (95.211.106.208 for
2.nfps.ws) which was included in the email with your access code. 4. PORT # for the
Server included in the email with your access code. Editing these items, the COM
PORT, YOUR ACCESS CODE, SERVER and the PORT ADDRESS into your rq-sssp-
client.conf file are explained in detail below. You should NOT make any other changes to
the rq-sssp-client.conf file at this time. Open NOTEPAD and MAXIMIZE the
WINDOW . Go to: MENU > FILE > OPEN and you get the open dialogue box. In
the "Files of type" drop down menu select All Files (See Figure A) or you will not see
the rq-sssp-client.conf file as notepad defaults to show only files with the .txt
extension. Figure A
In NOTEPAD with your WINDOW MAXIMIZED EDIT THE FOLLOWING: A.
YOUR COM PORT If Device Manager verified your PC COM PORT AS COM "1"
you may skip this step. If you com port number was other than "1" scroll down to the
line that says: serial_port=COM1 and change the "1" to # shown in device
manager. NOTE: When editing the card_server_url_1=newcamd: line (the last line of
the rq-sssp-client.conf file) be careful to NOT remove any of the special
characters that exist between the various fields such as _ = . : @ / if you do so or
add in a single space anywhere in this line IT WILL NOT WORK. B. Enter your
NFPS ACCESS CODE. Enter your ACCESS CODE into the card_server_url_1 line
which is the last line of this file. Replace twice (example
below) YOURACCESSCODE with your 14 digit access code. Make sure you do not
inadvertantly remove the : that seperate the two access codes. C. ENTER THE
CORRECT SERVER IP# Replace where it says SERVER with: 62.212.88.227 (if your
email told you to use the 1.nfps.ws server)95.211.106.208 (if your email told you to use
the 2.nfps.ws server) D. ENTER YOUR PORT # Edit the port number by replacing
the ##### with one of the 5 digit port #'s that you received with your access
code. NOTE: The port numbers and servers you were initially assigned are subject to
change. Should your service be interupted the first step you should do is check the
announcement forum at this site to see if there are new port or server assignments. If this
occurs simply re-edit your conference file with the latest server/port info and save as
instructed below. E. VERIFY EOF (INVISIBLE END OF FILE
CHARACTER) IMPORTANT !! Before you SAVE this file as instructed below,verify
the EOF by placing your cursor at the end of the card_server_url line immediately
after the 4 now hit the right arrow key on your keyboard and the cursor should drop
to next line - if it does not, then with the cursor after the 4 hit the return key once and
the cursor will now drop to the next line causing an eof to be entered. The .conf file
will not work if this is not included. F. VERIFY EDIT The last line of your .conf file
should now look like the example below, except it should now have your actual 14
digit access code inserted twice with a : between them and the server
IP# you were instructed to use along with one of the port numbers you were
assigned to replace the #####. The card_server_url line file has NO
SPACES between fields and when you open it in NOTEPAD (window
maximized) it should be on ONE LINE. If it appear on two lines in these instructions it
is due to width limitations on forum posts. EXAMPLE of card_server_url
line:card_server_url_1=newcamd://YOURACCESSCODE:YOURACCESS
CODE@SERVER:#####/6103403445406970987123412134 STEP
5. SAVING and PLACEMENT OF FILES Once you have edited this file
you need to SAVE it as a .conf file. It is IMPORTANT that you follow the next
instructions EXACTLY as written. In NOTEPAD go to MENU > File > Save AS and
the Save as dialogue box will appear. (See Figure B)
window. 16. Turn OFF your Coolsat using the rear switch. STEP
8. LOADING A CHANNEL LIST If using a channel list use the following
procedure to load it into your Coolsat Receiver. You will need: 1. Channel list - Use
the *.ndf you downloaded using one of the links above or from the Coolsat Files
Forum. 2. Coolsat v2.4 Loader software. 3. DB9 RS232 STRAIGHT THROUGH SERIAL
CABLE With your Coolsat Receiver still turned off and connected to your PC via a
DB9 RS232 straight through serial cable do the following toPREPARE YOUR
COOLSAT FOR LOADING A CHANNEL LIST. The Channel list is one of two
methods to repair the CaID mismatch problem, the other method is to do so
manually as instructed above. A.PREPARE YOUR COOLSAT FOR A CHANNEL
LIST 1. Unplug your Coolsat Receiver 2. Reconnect LNB cable in and cable out to
TV. 3. Plug in Coolsat. 4. Turn ON using the rear switch. 5. Turn the receiver ON using
the front button 6. Do an auto scan on the satellites you use (DO NOT DO THIS SCAN
AFTER YOU LOAD A CHANNEL LIST AS DOING SO WILL REMOVE THE CaID
FIX) 7. Turn autoroll Off on your receiver. B. LOADING YOUR CHANNEL LIST 1.
With your TV connected to your Coolsat and turned on using your CS Remote: "Menu" >
"System Setting"> "Database Reset" > "OK" > "Delete All Channels" > "OK" All
channels will be deleted. Press"Exit" to leave the "Menu". A message will display "No
Channels". 2. Execute the Pro Loader V2.4 software and select "Channels" tab on the
upper top application make sure "To Receiver" and "Normal Channels"are checked.
(SEE RED ARROWS IN FIGURE D) 3. Next, click the "Browse" button on the
application and select the path/directory where the Channel list *.ndf is located. When
found highlight it and click on the "Open" button to
continue. FIGURE D 4.
Next, click "Connect" button. A dialog box opens and shows the current "Bin"
version. 5. Press the "Start" button to continue the programming processes. DO NOT
INTERRUPT THIS PROCESS! 6. After completion a dialog box will show "Writing
100%". When "FINISH" displays, click on it. 7. The Coolsat will reboot You have
successfully loaded an external Channel list into the Coolsat. STEP
9. WATCHING TV If you have not loaded a channel list into your coolsat
you will find instructions on the manual method to repair the CaID mismatch at
the top of this guide under the heading "REQUIRED No. 5" 1. With your TV and
COOLSAT turned on and connected to your pc via a serial cable set your Coolsat to an
active nfps channel. Example: 300 for 119w 2. Click once on the shortcut (icon) in the
quick launch bar for rq-sssp-client.exe and you will get a black window on your pc screen
which will contain status information. 3. Within 30 seconds to a minute the channel you are
tuned to should come in. LAST STEP Enjoy your Coolsat Receiver
which once again is providing you entertainment via this IKS provider.