Professional Documents
Culture Documents
CE5000 SetUp Manual PDF
CE5000 SetUp Manual PDF
A-2 A little later, the start window is displayed. Press "Install CE5000" Cutting Plotter Controller In case of USB connection,
button to install the software and driver. Note : E-2 and E-4 may not be displayed on certain computers.
Install the Cutting Plotter Controller according to the instruction on the
* Windows and Windows XP are registered trademark of Microsoft Corporation in USA and other countries. C-1. Press the Next button. C-2. Press the Next button.
R R R
1. Check the content Note : If it is not displayed, press START menu of the Windows, then
select the Run. E-3. Select "Install the software E-4. Press the Next button.
1. Check the content Select [CD-ROM]: \MultiSetup.exe and press OK button. automatically (Recommended)" Install the item which is selected
2. Following accessories are attached to the plotter. Refer to the list and then press the Next button. as a default.
check the accessories.
Plotter - 1 unit Stand - 1 assembly
Note: If you are using the Windows95/98/Me, press START menu, the select the Run. C-3. Press the Next button. C-4. Press the Finish button.
Then select [CD-ROM]:\English\Drive\DSETUP.exe and press the OK button.
In case of the Windows95/98/Me, it is compatible with the CE5000 driver, so skip
to the section D-1.
E-5. Press "Continue Anyway" button. E-6. Press the Finish button.
A-3 Follow the installation wizard.
Power cable/USB cable Cutter plunger - 1 set Note : If "Software License Agreement" is displayed, check the
- 1 of each description. If you agree to the License agreement, press the Yes
button.
B-3. Press the Next button. B-4. Press the Next button.
D-5. Press "Continue anyway"
button. If specified port isn't available on F-7. Follow the instructions F-9. Press the Finish button.
the PC, the following window is displayed on the screen and
Left side of the plotter displayed and the distination port then press the Yes button.
Power cord (The screens that are displayed may differ
is changed to "File".
according to the operating system.
Check the contents of each screen before
621359400
CE5000 SERIES 2. Setting the roll media stand 6. Adjusting the media
OPERATION MANUAL
Raise
for CE5000-60
Provide slack
Stopper in the media
Stock shaft
Caution
To avoid bodily injury, always handle for CE5000-120
Fit in
1 09U 0 14 30 2
Set FORCE, SPEED and
QUALITY with reference to
1 Preparing the cutter blade and the Roll media Sheet media
cutter pen plunger
4 Turn on the cutting plotter
A rough guide of the setting
Set the shaft Insert the stoppers into both end of the core. Material Thickness(mm) Blade Cutting force Speed Quality
Adjusting the cutter blade length Outdoor vinyl 0.05 to 0.08 CB09UA 10-14 1-30 2
3-1. Pull out the roll media and pass through the CE5000 Press the "|" (for small size character cutting) 0.05 to 0.08 CB15UB 10-14 1-20 1
Cutter pen plunger (in case of roll media) side of its power
switch
Film for decoration 0.08 to 0.1 CB09UA 14-17 1-30 2
Pull out the roll media Transparent/translucent film 0.08 to 0.1 CB09UA 14-20 1-30 2
Extend the blade Extract the blade Reflection film 0.08 to 0.1 CB09UA 14-20 1-30 2
Guide of the cutter blade length Fluorescent film 0.20 to 0.25 CB09UA 20-21 1-20 1
Too short Right Too long Fluorescent film 0.20 to 0.25 CB15U 20-21 1-20 1
Cutter blade Adjust the cutting force so that the cutting trace lightly appears on the
media liner.
2 Mounting the cutter pen plunger When using a sheet media. 1 09U 0 14 30 2 Press the TEST key
Select media mode
using arrow keys. Caution: Be sure to keep your hands, hair, and face away from
SHEET PRESS ENTR the moving parts.
4. Align the media with the CE5000
Mount
CE5000-60 CE5000-120 Press the ENTER key
to start media size
detection.
Align the media to Align the media Origin point Check the corners of the triangle.
the guide line to the scale
When using a roll media and When using a roll media and
setting the origin point to the top setting the origin point to the
of media. current setting position.
Move the cursor to adjust the offset value, repeat the adjustment
Pen bracket until the result becomes proper.
1 09U 0 14 30 2 Corners are cut properly. Press the ENTER key to finish.
Select a blade If the ENTER key is pressed, then the setting conditions are stored
Media sensor into the memory.
621359400