Professional Documents
Culture Documents
Routing Assessment
Routing Assessment
Routing Assessment
1. Which command can you enter to set the default route for all traffic to an interface?
2. A router has learned three possible routes that could be used to reach a destination
network. One route is from EIGRP and has a composite metric of 20514560. Another
route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4.
Which of the above routes will be installed in the Router’s routing table?
3. Two routers named Atlanta and Brevard are connected via their serial interfaces as
illustrated, but they are unable to communicate. The Atlanta router is known to have
the correct configuration.
Given the partial configurations, identify the fault on the Brevard router that is causing the
lack of connectivity
A. incompatible IP address
B. insufficient bandwidth
C. incorrect subnet mask
D. incompatible encapsulation E. link reliability too low
F. IPCP closed
A. HDLC
B. PPP
C. X.25
D. Frame Relay
5. Which command can you enter to determine whether serial interface 0/2/0 has been
configured using HDLC encapsulation?
A. router#show platform
B. router#show interfaces Serial 0/2/0 C. router#show ip interface s0/2/0
D. router#show ip interface brief
6. Which command can you enter to verify that a BGP connection to a remote device is
established?
8. Which three statements about link-state routing are true? (Choose three.)
A. OSPF is a link-state protocol.
B. Updates are sent to a broadcast address.
C. It uses split horizon.
D. Routes are updated when a change in topology occurs. E. RIP is a link-state
protocol.
F. Updates are sent to a multicast address by default.
A. link-state
B. distance-vector C. path-vector
D. other
11. Which three statements about static routing are true? (Choose three.)
12. What are the address that will show at the show ip route if we configure the above
statements? (Choose Three.)
A. 10.0.0.0
C. 172.15.4.0 E. 192.168.4.0
B. 10.4.3.0
D. 172.15.0.0 F. 192.168.0.0
13. Find the IP configuration of Fa 0/0 interface below. You need to advertise the network of
Interface, Fa0/0. What IP – Mask Combination should be used for this?
interface fa0/0
ip address x.x.x.33 255.255.255.224 router bgp XXX
neighbor x.x.x.x remote as x.x.x.x
14. Which of the following events will generate a Syslog output messages?
15. You need to implement a routing protocol that meets the following requirements: 1.
Converges quickly
2. Supports VLSM, IP, and IPX.
3. Uses minimal bandwidth for routing updates.
Which one of the following routing protocols would be the best choice?
16. Which two statements about using the CHAP authentication mechanism in a PPP link are
true? (Choose two.)
EIGRP
17. Which three characteristics are representative of a link-state routing protocol? (Choose
three.)
A. provides common view of entire topology B. exchanges routing tables with neighbors C.
calculates shortest path
D. utilizes event-triggered updates
18. You are a network administrator at Mohan’s and you need to implement a routing
protocol on your network that provides:
19. You need to configure a single router into load balancing traffic across 4 unequal Cost
paths. Which routing protocols can satisfy this requirement? (Select two)
A. It is used with the OSPF priority values to determine which OSPF router will become the
DR or BDR in a point-to-point network
B. It is used with the OSPF priority values to determine which interface will be used to form
a neighbor relationship with another OSPF router
C. It is used with the OSPF priority values to determine which router will become the DR or
BDR in a multi access network
D. It is used to determine which interfaces will send Hello packets to neighboring OSPF
routers
23. Which command will display all the EIGRP feasible successor routes known to a router?
24. Which of the following statements are true regarding the command ip route 172.16.4.0
255.255.255.0 192.168.4.2? (Choose two)
25. If routers in a single area are configured with the same priority value, what value does a
router use for the OSPF Router ID in the absence of a loopback interface?
A. The lowest IP address of any physical interface B. The highest IP address of any physical
interface C. The lowest IP address of any logical interface D. The highest IP address of any
logical interface