STANDARD SPECIFICATION No.
SOU |AGNES . STANDAMD SPECIFICATION FOR ce
g@enielees@NDAUMITED STAINLESS STEEL PLATES 6-12:0020 fov.7
Bee eeteee nee ace
Bada wit wet aT
aren fearfreet
STANDARD SPECIFICATION
FOR
STAINLESS STEEL PLATES
7 30.06.2010
6 250902 REVISED AND REISSED AS STD. SPEC ve RKG ‘KM ——-N.DUARI
5 16.0404 _REVISEDANDREISSEDAS STD. SPEC DN AK SSA skG
4 26.1199 -REVISEDANDREISSEDAS STD. SPEC KT ARM RMN A.SONI
3 27.0595 REVISED AND REISSED AS STD. SPEC. KPs KM ve ‘ASONI
aa : ‘Standards — Standards
Re ato Purpose Propared Checked Cotvono? _chalmman
No by by —Cenvenor _Chairman _
‘Approved by
Format No, @-00-0001-F' Rev. 0 Copyright EL — All rights reservedASME,
ASTM
EN
ss
‘STANDARD SPECIFICATION No.
STANDARD SPECIFICATION FOR
STAINLESS STEEL PLATES cz ouol need
age.
American Society of Mechanical Engineers
American Society for Testing & Materials
European Standard
Rockwell Hardness Scale B
Stainless Steel
Static Equipment Standards Committee
Convenor: Mr. A.K. Malik
Members
Mr. RK. Trivedi
Mr. K. Anjaneyulu
Mr. Tarun Kumar
Mr. Chandra Kant (Inspection)
Mr. GK. lyer (Construction)
Mr. Ratan Lal (Project)
Format No, 6-00-0001-F1 Rev. 0
‘Copyright EI — Al rants reserved1.0
2.0
3.0
40
3.0
6.0
‘STANDARD SPECIFICATION No,
SAGER ByENGNERS STANDARD SPECIFICATION FOR
Gite ROARED STAINLESS STEEL PLATES
CONTENTS
SCOPE...
GENERAL.
SUPPLEMENTARY TECHNICAL REQUIREMENTS.
CERTIFIED DOCUMENTS.
PAINTING AND COATING...
INSPECTION AUTHORITY.
Format No, 6-00-0001-F1 Rev. 0
‘Copyright EL — All righ resened20
2d
22
23
24
3.0
34
32
33
34
35
40
‘STANDARD SPECIFICATION No.
SGHfSIzTET Sy ENGNEERS, TANDARD SPECIFICATION FOR
TSAR STANDARD SI
—— STAINLESS STEEL PLATES 6-12-0020 Rev. 7
Page tot 5.
SCOPE
This specification covers requirements for chromium, chromium-nickel and chromium-
manganese-nickel stainless and heat resisting steel! plates intended primarily for pressure
vessels/heat exchangers. The steel plates shall meet the requirements of ASME Boiler and
Pressure Vessel Code Section II (latest). This is intended to supplement the minimum
applicable requirements of the material specification indicated in the material requisition.
GENERAL
Plates supplied to this specification shall conform to specification SA-480 with additional
requirements mentioned herein.
Plate length and width provide tolerance for shear and plasma cutting only. The tolerance on
‘thickness of plates shall be positive only.
Final Rolling shall be lengthwise.
Plates shall have no. | finish on both sides with reference to SA-480.
SUPPLEMENTARY TECHNICAL REQUIREMENTS
All plates shall be supplied in hot-rolled, fully annealed and pickled condition. All stabilized
grades of Stainless Steel (SS 321, SS 347etc.) shall be given stabilization heat treatment in
addition to solution annealing,
Unless specified otherwise in material requisition, plate representative of each heat shall be
subjected to intergranular corrosion tests as per ASTM A-262 Practice E for all the 300 series
materials. The bend test specimen shall be examined at a magnification of 200 x; and bent
specimen shall be free of any cracks or grain dropping.
For straight chrome (13% Cr) material, maximum carbon ‘content shall not exceed 0.06%.
Hardness of UNS No. $4100, $41008 and $40500 shall not exceed 88 RB.
a. Plate having thickness 16 mm to 50 mm (both inclusive) shall be examined ultrasonically
as per SA-435.
b. For thickness above 50mm ultrasonic examination shall be carried out as per SA-578 and
shall have acceptance standard of level-B.
All mandatory tests as per material specification shall be carried out. However tension test
specimen shall be from finished material and shall be selected in transverse direction.
CERTIFIED DOCUMENTS
The supplier shall furnish 6 copies of the following certificates/documents inclusive of all
tests required as per specification duly certified by the Inspecting Authority before shipment
of plates. The actual values obtained shall be recorded in the test certificates/documents.
‘Material certificates shall conform to EN 10204 Type 3.2.
a. Chemical Analysis
b. Mechanical Tests
c. Data of heat treatment i.e. initial temperature, heating rate, soaking temperature, cooling
rate, ete
Format No. 8-00-0001-F1 Rev. 0 Copyight BIL — Al ights reservedsar
5.0
6.0
STANDARD SPECIFICATION No
sGifetziel Gy ENGNERS STANDARD SPECIFICATION FOR
elsies FINDA UMITED ~' STaINLESS STEEL PLATES 6-12-0020 Rev.7
ESS wtetanarinene peasars
d. Ultrasonic Examination
e. Intergranular corrosion test for 300 series
f. Intergranular corrosion test for series other than 300 (whenever specified in the
requisition)
g. Type of finish for plate surfaces
PAINTING AND COATING
Plates are not to be painted/coated but shall be covered with plastic foils or paper or by other
means for careful protection and shall be packed against any damage during transit and sea-
weather conditions.
INSPECTION AUTHORITY
EIL/Lioyds Register of Shipping/Third Party approved by EIL as indicated in the requisition.
Format No, 6-00-0001-Ft Rov. ‘Copyright EI — All ights reserved