Professional Documents
Culture Documents
Crane PDF
Crane PDF
Hoist Rope 26
Specifications
&
Lifting Capacities
1303(B)01T.EA220
SCX1000A-3 VARIATION
110 (45)
(Rated with 12 t load)
m/min
Third Winch
95 (30)
(Rated with 12 t load)
-1
Swing Speed min (rpm) 2.3
Travel Speed High / Low * km/h 2.0 / 1.1
Gradeability % (Degree) 30 (17)
ISUZU 6HK1
Engine Model
(Stage Ⅲ B, Int. Tier 4)
kW/min-1 210 / 1900
Engine Rated Output Power
(ps/rpm) (285 / 1900)
Note : Speeds marked with "*" may vary depending on load applied.
2
VARIATION SCX1000A-3
Crane Specification
(Boom Longest Length with Crane Jib)
Boom Length m 24 to 51
Crane Jib Length m 10 to 28
Boom + Crane Jib
m 51 + 28
Longest Length
115 (1.17)
Ground Contact
kPa (kgf/cm²) (Boom + crane jib longest length 35 t + 12
Pressure
t hook attached)
Approximately 108
Overall Operating
t (Boom + crane jib longest length 35 t + 12
Weight
t hook attached)
3
SCX1000A-3 CONTENTS
VARIATION
SPECIFICATIONS
Specifications 6
Crane Specifications 7
Dimensions and Specifications................................................................................................................. 7
Boom and Crane Jib Configurations......................................................................................................... 8
Combination of Boom and Crane Jib (Offset Angle 10° and 30°)........................................................... 9
Working Ranges........................................................................................................................................ 10
Main Boom ....................................................................................................................................................... 10
4
CONTENTS SCX1000A-3
Clamshell Specifications 40
Dimensions and Specifications............................................................................................................... 40
Working Ranges................................................................................................................................................. 40
Specifications..................................................................................................................................................... 40
Clamshell Bucket................................................................................................................................................ 40
TECHNICAL DATA
Equipment List 45
Standard and Optional Equipment.......................................................................................................... 45
5
Specifications
SCX1000A-3 SPECIFICATIONS
Specifications
Engine Third Winch
Rope Diameter 26 mm
Incorporated 205 m
Model ISUZU 6HK1
Rope Length Max. for Work 170 m
Type 4-cycle, Water-cooled, Direct injection, Turbo-charged,
Max. for Non Work 220 m
Diesel engine
Rated 117 kN
Displacement 7.79 liters Line Pull
Max. at 1st Lay 215 kN
Rated Output 210 kW / 1,900 min-1 (285 ps / 1,900 rpm)
Free fall winch with brake controled by pedal
Fuel Tank Capacity 460 liters Optional Equipment
operation.
Notes Engine meets Stage Ⅲ B / Int. Tier 4 of engine exhaust
gas emission regulations in USA, Europe, and Japan.
Engine rated horsepower is based on international rating
formula that includes engine alternator and without fan.
Swing System
Consisted of 2 hydraulic motors with reduction gear and
Control multi-disc brakes and a swing bearing which has inner
tooth. Optional swing brake pedal enables operator to
control swing precisely.
Main actuators are actuated by main hydraulic system
controlled with pilot hydraulic system. Safety devices are
securely operated by combined various electronic control
Control System
with hydraulic system. Working speed can be precisely
controlled according to control lever stroke and control Gantry
dials depending on work.
Designed and positioned based on ergonomics. Arm-chair Gantry is welded steel construction. Raised and lowered
Control Levers lever type is standard. Cross operation lever type and front by power hydraulic cylinders.
lever type are available as option.
8 inches size. Located to check work state easily without
Display Panel Design
disturbing the view of the operator.
Counterweight
Total Weight 37.0 ton
Hydraulic System 9.0 ton Base Weight 1 piece
6.6 ton Insert Weight 2 pieces
Hydraulic Oil Tank Capacity 320 liters Upper Weight
9.0 ton Insert Weight 1 piece
Max. 31.4 MPa 2.8 ton Top Weight 1 piece
for Front, Rear, boom hoist winch 3.0 ton Top Weight 1 piece
P1 266 liters / min
and travel Total Weight 12.0 ton
for Front, Rear, third winch and Lower Weight
P2 266 liters / min 6.0 ton Lower Weight 2 pieces
travel
Hydraulic Pump Capacity for Swing, Jack, Sideframe retract
P3 152 liters / min
P4 39 liters / min
and Gantry cyl.
Carbody Frame
P5 39 liters / min Pilot control, Brake cooling, Welded steel construction with jack up deveice and
P6 39 liters / min Reeving tagline, etc. crawler sideframe extend-retract cylinders.
P7 29 liters / min
6
Crane Specifications
Dimensions and Specifications
SPECIFICATIONS SCX1000A-3
Crane Specifications
Dimensions and Specifications
4150
4990
s)
0 diu
30 Ra
R4 ing
Sw
nd
rE
ea
(R
R4300 1200
0
00
12
3740
2110
1395
1110
425
5375 810
4990(3400)
6295
7
Crane Specifications
SCX1000A-3 SPECIFICATIONS Boom and Crane Jib Configurations
Boom Boom
Boom Length Boom Length
Boom Configurations Boom Configurations
(m) (m)
5.3 3 3 9 9 9
12 5.3
6 6
6 3 3 9 9 9 6
3 45
5.3
15 6 9 9 9
5.3
6 3 6
6 6 9 9 9 6
3 3
5.3 3 6 9 9 9
6 3 3 6 5.3
18 6 3 6 9 9 9 6
6 48
5.3 9 9 9 9
6 6 6 5.3
6 9 9 9 9 6
3 6
5.3 3 3 6 9 9 9
6 3 6 6 5.3
21 6 3 3 6 9 9 9 6
9 51
5.3 3 9 9 9 9
6 9 6 5.3
6 3 9 9 9 9 6
3 3 6
5.3 3 3 9 9 9 9
6 3 3 6 6 5.3
24 6 3 3 9 9 9 9 6
3 9 54
5.3 6 9 9 9 9
6 3 9 6 5.3
6 6 9 9 9 9 6
3 3 9
5.3 3 6 9 9 9 9
6 3 3 9 6 57 5.3
27 6 3 6 9 9 9 9 6
6 9
5.3 3 3 6 9 9 9 9
60 5.3
6 6 9 6
6 3 3 6 9 9 9 9 6
3 6 9
5.3
6 3 6 9 6
30
9 9
5.3
6 9 9 6
3 3 6 9
5.3
6 3 3 6 9 6
33
3 9 9
5.3
6 3 9 9 6
3 3 9 9
5.3
6 3 3 9 9 6
36
6 9 9
5.3
6 6 9 9 6
3 6 9 9
5.3
6 3 6 9 9 6
39
9 9 9
5.3
6 9 9 9 6
3 3 6 9 9
5.3
6 3 3 6 9 9 6
42
3 9 9 9
5.3
6 3 9 9 9 6
8
Crane Specifications
Combination of Boom and Crane Jib (Offset Angle 10° and 30°)
SPECIFICATIONS SCX1000A-3
Combination of Boom and Crane Jib (Offset Angle 10° and 30°)
Combination of Boom and Crane Jib (Offset Angle 10° and 30°)
Boom Length (m) 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60
10
Jib Length
16
(m)
22
28
( : Attachable : Not Attachable )
Crane Jib (Offset Angle 10° and 30°)
Crane Jib Length (m) Offset Angle Crane Jib Configurations
9.6
8.3
10°
5 5
10
9.6
8.3 1.6
30°
5 5
5.7
8.3 9.6
10°
5 6 5
16
5.7
9.6
8.3 1.6
30°
5 6 5
5.7
5.7
8.3 9.6
10°
5 6 6 5
22
5.7
5.7
9.6
8.3 1.6
30°
5 6 6 5
5.7
5.7
8.3 5.7
10° 9.6
5 6 6 6 5
28
5.7
5.7
5.7
8.3 9.6
1.6
30°
5 6 6 6 5
Check the pendant rope with referring to the imprints on the rope end.
Dimensions Not Shown In The Figure Jib Pendant Rope
Symbols Jib Length (m) Length (m) Rope Diameter (mm) Imprint
5 5 1.6 24 □・△・24・1.6・S
6 6 5.7 24 □・△・24・5.7・S
8.3 24 □・△・24・8.3・S
9.6 24 □・△・24・9.6・S
9
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
Working Ranges
Main Boom
4.3 m
4.4 m
4.6 m
100 t Hook 50 t Hook 35 t Hook
80°
65
60 m
60
57 m
55 54 m
51 m
50 48 m 44°
45 m
45
42 m
39 m 38°
Height Above Ground
40
36 m
35 33 m
32°
30 m
30°
30 27 m
25 24 m
(m) 21 m
20 18 m
15 m
15 12m
10
Minimum Boom Angle
0 5 10 15 20 25 30 35 40 45 50
1.20 m
2.11 m
10
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
Aux. Sheave
4.0 m
Maximum Boom Angle
80°
65
60
57 m
55 54 m
49°
51 m
50 48 m
45 m 45°
45
42 m
40 39 m
Height Above Ground
40°
36 m
35 33 m
30 m
30 27 m
30°
24 m
25
21 m
(m)
20 18 m
15 m
15 12m
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45
1.20 m
2.11 m
11
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
4.3 m
4.4 m
4.6 m
100 t Hook 50 t Hook 35 t Hook
80°
65
60
57 m
55 54 m
51 m
50 48°
48 m
45 m
Height Above Ground
45
42 m 43°
40 39 m
36 m
35 33 m 37°
30 m
30 27 m
(m) 30°
24 m
25
21 m
20 18 m
15 m
15 12m
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45
1.20 m
2.11 m
12
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
3.5 m
10 m Crane jib
offset angle 10°
30°
10° 10 m Crane jib
Maximum Boom Angle offset angle 30°
80°
65
60
48°
55 47°
51 m
50 48 m 44°
43°
45 m
45
42 m
40 39 m 38°
Height Above Ground
36 m 37°
35 33 m
30 m
30°
30 27 m
25 24 m
(m)
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45 50
1.20 m
2.11 m
13
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
3.5 m
16 m Crane jib
offset angle 10°
16 m Crane jib
30° offset angle 30°
10°
Maximum Boom Angle
80° 52°
70 51°
65
49°
47°
60
55 44°
51 m
43°
50 48 m
45 m
Height Above Ground
45 38°
42 m
37°
39 m
40
36 m
35 33 m
30°
30 m
30 27 m
(m) 24 m
25
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45 50 55
1.20 m
2.11 m
14
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
3.5 m
22 m Crane jib
offset angle 10°
30°
70 51°
50°
65
48°
60
45°
55
51 m 43°
50 48 m
Height Above Ground
45 m
45 38°
42 m
37°
39 m
40
36 m
35 33 m
30°
30 m
(m) 30 27 m
24 m
25
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45 50 55
1.20 m
2.11 m
15
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
28 m Crane jib
3.5 m
offset angle 10°
30°
10° 28 m Crane jib
offset angle 30°
Maximum Boom Angle
70
48°
65
46°
60
43°
55
41°
50 51 m
Height Above Ground
38°
45 m
45
42 m
40 39 m
36 m
30°
35 33 m
30 m
(m) 30
27 m
25 24 m
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45 50 55 60
1.20 m
2.11 m
16
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
4.3 m
4.4 m
50 t Hook 35 t Hook
80°
65
60
55
51 m
50 48 m
45 m
45 44°
42 m
40 39 m
Height Above Ground
36 m 38°
35 33 m
30 m
30 27 m 31°
30°
25 24 m
(m)
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45
1.20 m
2.11 m
17
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
4.3 m
4.4 m
50 t Hook 35 t Hook
30°
10 m Crane jib
Maximum Boom Angle offset angle 30°
80°
65
60
55
51 m
50 48 m
45 m
45 44°
42 m
39 m
40
Height Above Ground
36 m 39°
35 33 m
30 m
30 27 m 31°
30°
24 m
25
(m)
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40 45
1.20 m
2.11 m
18
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
4.3 m
4.4 m
10° 50 t Hook 35 t Hook
16 m Crane jib
Maximum Boom Angle offset angle 10°
80°
70
65
60
55
51 m
50 48 m
45 m
45
42 m 47°
Height Above Ground
39 m
40
36 m
42°
35 33 m
30 m
30 27 m
35°
24 m
(m) 25 30°
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40
1.20 m
2.11 m
19
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
4.3 m
4.4 m
30°
16 m Crane jib 50 t Hook 35 t Hook
Maximum Boom Angle offset angle 30°
80°
70
65
60
55
51 m
50 48 m
45 m
45
42 m 47°
Height Above Ground
39 m
40
36 m 42°
35 33 m
30 m
36°
30 27 m
24 m
25 30°
(m)
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40
1.20 m
2.11 m
20
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
4.3 m
4.4 m
10°
22 m Crane jib
Maximum Boom Angle offset angle 10°
50 t Hook 35 t Hook
80°
75
70
65
60
55
51 m
50 48 m
45 m 49°
45
42 m
Height Above Ground
39 m 44°
40
36 m
35 33 m 39°
30 m
30 27 m
24 m 32°
(m) 25 30°
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40
1.20 m
2.11 m
21
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
4.3 m
4.4 m
30°
22 m Crane jib
Maximum Boom Angle offset angle 30°
50 t Hook 35 t Hook
80°
75
70
65
60
55
51 m
50 48 m
50°
45 m
45
Height Above Ground
42 m
45°
39 m
40
36 m
35 33 m 40°
30 m
30 27 m
24 m 32°
(m)
25 30°
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40
1.20 m
2.11 m
22
Crane Specifications
Working Ranges
SPECIFICATIONS SCX1000A-3
28 m Crane jib
4.3 m
4.4 m
10° offset angle 10°
Maximum Boom Angle
80°
80
50 t Hook 35 t Hook
75
70
65
60
55
51 m 52°
50 48 m
Height Above Ground
45 m 49°
45
42 m
40 39 m
44°
36 m
35 33 m
30 m 36°
(m) 30
27 m
25 24 m 30°
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40
1.20 m
2.11 m
23
Crane Specifications
SCX1000A-3 SPECIFICATIONS Working Ranges
4.3 m
4.4 m
30°
28 m Crane jib
Maximum Boom Angle offset angle 30°
70
65
60
55
51 m
52°
50 48 m
Height Above Ground
45 m
45 48°
42 m
39 m
40 43°
36 m
35 33 m
30 m 38°
(m) 30 27 m
24 m
25 30°
20
15
10
Minimum Boom Angle
5
0 5 10 15 20 25 30 35 40
1.20 m
2.11 m
24
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
6. Hook weights are shown in the table below.
Hook Capacity Hook Weight Maximum Rated Loads (t)
(t) (t) 8falls 7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall
100 1.20 100 84 72 60 48 - - -
50 1.17 - - - 50 48 36 24 -
35 0.90 - - - - - 35 24 -
12 0.51 - - - - - - - 12
25
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
Aux. Sheave
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
6. Hook weights are shown in the table below.
Hook Capacity Hook Weight Maximum Rated Loads (t)
(t) (t) 8 falls 7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall
100 1.20 100 84 72 60 48 - - -
50 1.17 - - - 50 48 36 24 -
35 0.90 - - - - - 35 24 -
12 0.51 - - - - - - - 12
26
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
6. Hook weights are shown in the table below.
Hook Capacity Hook Weight Maximum Rated Loads (t)
(t) (t) 8 falls 7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall
100 1.20 100 84 72 60 48 - - -
50 1.17 - - - 50 48 36 24 -
35 0.90 - - - - - 35 24 -
12 0.51 - - - - - - - 12
27
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
Crane Jib
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The offset angles shown are of jib boom offset angle against the main boom, under load.
6. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
7. Hook weight are shown in the table below.
Hook Capacity Hook Weight
(t) (t)
100 1.20
50 1.17
35 0.90
12 0.51
28
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
Crane Jib
29
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
Crane Jib
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The offset angles shown are of jib boom offset angle against the main boom, under load.
6. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
7. Hook weight are shown in the table below.
Hook Capacity Hook Weight
(t) (t)
100 1.20
50 1.17
35 0.90
12 0.51
30
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
Crane Jib
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The offset angles shown are of jib boom offset angle against the main boom, under load.
6. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
7. Hook weight are shown in the table below.
31
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
Crane Jib
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The offset angles shown are of jib boom offset angle against the main boom, under load.
6. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
7. Hook weight are shown in the table below.
Hook Capacity Hook Weight
(t) (t)
100 1.20
50 1.17
35 0.90
12 0.51
32
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
33
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
34
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
35
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
36
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
37
Crane Specifications
SCX1000A-3 SPECIFICATIONS Gross Rated Load Table
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
6. Hook weights are shown in the table below.
Hook Capacity Hook Weight Maximum Rated Loads (t)
(t) (t) 8 falls 7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall
100 1.20 100 84 72 60 48 - - -
50 1.17 - - - 50 48 36 24 -
35 0.90 - - - - - 35 24 -
12 0.51 - - - - - - - 12
38
Crane Specifications
Gross Rated Load Table
SPECIFICATIONS SCX1000A-3
1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.
2. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.
3. To calculate the maximum load that can actually be lifted, deduct weight of all lifting accessories, such as boom hook and jib hook, from figures shown above.
4. Working radius is the horizontal distance from the slewing center to the center of gravity of a lifted load.
5. The counterweight is 49.0 ton. (Upper weight 37.0 ton + Lower weight 12.0 ton)
6. Hook weights are shown in the table below.
Hook Capacity Hook Weight Maximum Rated Loads (t)
(t) (t) 8 falls 7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall
100 1.20 100 84 72 60 48 - - -
50 1.17 - - - 50 48 36 24 -
35 0.90 - - - - - 35 24 -
12 0.51 - - - - - - - 12
39
Clamshell Specifications
SCX1000A-3 SPECIFICATIONS Dimensions and Specifications
Clamshell Specifications
Dimensions and Specifications
R4300 1200
H1
00
40
o2
0t
3305
B
00
A
12
1395
H2
C
L
5375
D
6295
Working Radius
Working Ranges
Boom Length m 12 15 18 21 24
Boom Angle ° 35 45 55 65 35 45 55 65 35 45 55 65 35 45 55 65 35 45 55 65
Working Radius m 11.6 10.4 8.8 7.1 14.0 12.5 10.5 8.4 16.5 14.6 12.3 9.6 19.0 16.7 14.0 10.9 21.4 18.8 15.7 12.2
Gross Rated Load t 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0
Lift L (D + H2) m 37.2 38.8 40.2 41.4 38.8 40.9 42.6 44.0 40.4 42.9 45.0 46.7 42.0 44.9 47.4 49.3 43.6 47.0 49.8 52.0
Max. Digging
m 36
Depth D
Bucket Dumping
m 1.2 2.8 4.2 5.4 2.8 4.9 6.6 8.0 4.4 6.9 9.0 10.7 6.0 8.9 11.4 13.3 7.6 11.0 13.8 16.0
Height H2
40
Weights and Dimensions of Disassembled Units
Weights and Dimensions List
TECHNICAL DATA SCX1000A-3
3480
Boom Hoist Winch Wire Rope 1 48400
Crawlers
Jack
Without:
Floats
6295 3400
3480
1 46300
Crawlers
Jack
Without:
Floats 6295 3400
8200
Base Crane with:
Front Winch Wire Rope
Rear Winch Wire Rope
3190
6295 1060
Crawler 2 9600
1110
41
Weights and Dimensions of Disassembled Units
SCX1000A-3 TECHNICAL DATA Weights and Dimensions List
4150 805
990
4150 495
4150 690
1625 560
560 1535
1890 690
6185 1825
1975
42
Weights and Dimensions of Disassembled Units
Weights and Dimensions List
TECHNICAL DATA SCX1000A-3
1660 6700
2180
1660 3140
1660 6140
1660 9140
1770
1895 605
1110
1430
43
Weights and Dimensions of Disassembled Units
SCX1000A-3 TECHNICAL DATA Weights and Dimensions List
5120 1040
Jib Base
1 580
(with Jib Strut)
1110
1010 5430
910
6080 1040
930
820 600
130
170
790 480
120
50 t Hook 1 1170
1970
155
790 370
84
35 t Hook 1 900
1835
35t
120
355
44
Equipment List
Standard and Optional Equipment
TECHNICAL DATA SCX1000A-3
Equipment List
Standard and Optional Equipment
: Standard : Optional : No setting
45
Equipment List
SCX1000A-3 TECHNICAL DATA Standard and Optional Equipment
46
Equipment List
Standard and Optional Equipment
TECHNICAL DATA SCX1000A-3
47
SCX1000A-3 M E M O
M E M O SCX1000A-3
SCX1000A-3 M E M O
•• We are constantly improving our products and therefore reserve the right to change designs and speafications without notice.
•• Units in this specification are shown under International System of Units; the figures in parenthesis are under Gravitational System
of Units as old one.