Professional Documents
Culture Documents
Fire
Fire
PART 1 - GENERAL
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.
0.2 SUMMARY
1. Division 2 piping Sections for general-duty and specialty valves for site construction
piping.
2. Division 13 fire-suppression piping and fire pump Sections for fire-protection valves.
3. Division 15 Section "Mechanical Identification" for valve tags and charts.
4. Division 15 Section "HVAC Instrumentation and Controls" for control valves and
actuators.
5. Division 15 piping Sections for specialty valves applicable to those Sections only.
0.3 DEFINITIONS
VALVES 15110 - 1
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
0.4 SUBMITTALS
A. Product Data: For each type of valve indicated. Include body, seating, and trim materials;
valve design; pressure and temperature classifications; end connections; arrangement;
dimensions; and required clearances. Include list indicating valve and its application. Include
rated capacities; shipping, installed, and operating weights; furnished specialties; and
accessories.
A. ASME Compliance: [ASME B31.1 for power piping valves and]ASME B31.9 for building
services piping valves.
1. Exceptions: Domestic hot- and cold-water[, sanitary waste, and storm drainage]
piping valves unless referenced.
B. ASME Compliance for Ferrous Valves: ASME B16.10 and ASME B16.34 for dimension and
design criteria.
C. Use sling to handle large valves; rig sling to avoid damage to exposed parts. Do not use
handwheels or stems as lifting or rigging points.
VALVES 15110 - 2
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
PART 2 - PRODUCTS
0.1 MANUFACTURERS
A. In other Part 2 articles where subparagraph titles below introduce lists, the following
requirements apply for product selection:
B. Bronze valves shall be made with dezincification-resistant materials. Bronze valves made
with copper alloy (brass) containing more than 15 percent zinc are not permitted.
C. Bronze Valves: NPS 2 (DN 50) and smaller with threaded ends, unless otherwise indicated.
D. Ferrous Valves: NPS 2-1/2 (DN 65) and larger with flanged ends, unless otherwise indicated.
E. Valve Pressure and Temperature Ratings: Not less than indicated and as required for system
pressures and temperatures.
G. Valve Actuators:
1. Chainwheel: For attachment to valves, of size and mounting height, as indicated in the
"Valve Installation" Article in Part 3.
2. Gear Drive Operator: For quarter-turn valves NPS 8 (DN 200) and larger.
3. Handwheel: For valves other than quarter-turn types.
4. Lever Handle: For quarter-turn valves NPS 6 (DN 150) and smaller, except plug valves.
5. Wrench: For plug valves with square heads. Furnish Owner with 1 wrench for every 10
plug valves, for each size square plug head.
H. Valves in Insulated Piping: Valves shall have 2-inch (50-mm) stem extensions and the
following features:
VALVES 15110 - 3
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
I. Valve Flanges: ASME B16.1 for cast-iron valves, ASME B16.5 for steel valves, and
ASME B16.24 for bronze valves.
1. Caution: Use solder with melting point below 840 deg F (454 deg C) for angle, check,
gate, and globe valves; below 421 deg F (216 deg C) for ball valves.
A. Bronze Angle Valves, General: MSS SP-80, with silicon bronze stem, non-asbestos packing
and malleable-iron handwheel.
B. Class 150, Bronze Angle Valves: ASTM B 62 bronze body with TFE disc, union-ring bonnet,
threaded ends, and having 300-psig (2070-kPa) CWP rating.
C. Class 300, Bronze Angle Valves with Stainless-Steel Disc: ASTM B 61 bronze body with
stainless-steel plug and renewable seat, union-ring bonnet, threaded ends, and having 600-psig
(4140-kPa) CWP rating.
VALVES 15110 - 4
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
A. Cast-Iron Angle Valves, General: MSS SP-85, Type II; having ASTM A 126, Class B cast-iron
body and bolted bonnet; bronze mounted, non-asbestos packing and gaskets; and flanged-end
connections.
B. Class 125, Cast-Iron, Standard Angle Valves: 200-psig (1380-kPa) CWP rating.
C. Class 250, Cast-Iron, Stop-Check Angle Valves: Stop-check design with non-asbestos packing
and gaskets, and having 500-psig (3450-kPa) CWP rating.
A. Bronze Ball Valves, General: MSS SP-110 and have bronze body complying with
ASTM B 584, except for Class 250 which shall comply with ASTM B 61, full-depth ASME
B1.20.1 threaded or solder ends, and blowout-proof stems.
B. Two-Piece, Full-Port, Bronze Ball Valves with Bronze Trim: Chrome-plated bronze ball and
bronze stem and; reinforced TFE seats; threaded body packnut design (no threaded stem designs
allowed) with adjustable stem packing, solder or threaded ends; and 150 psig (1034 kPa) SWP
600-psig (4140-kPa)CWP rating.
C. Two-Piece, Full-Port, Bronze Ball Valves with Stainless-Steel Trim: Type 316 stainless-steel
vented ball and stem, reinforced TFE seats, threaded body packnut design (no threaded stem
designs allowed) with adjustable stem packing, soldered or threaded ends; 150 psig (1034 kPa)
SWP and 600-psig (4140-kPa) CWP ratings.
VALVES 15110 - 5
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
D. Two-Piece, Full-Port, 250 psig (1723 kPa) SWP, Bronze Ball Valves with Stainless-Steel Trim:
Type 316 stainless-steel vented ball and stem, carbon-filled TFE seats, threaded body packnut
design (no threaded stem designs allowed) with adjustable stem packing, threaded ends; 250
psig (1723 kPa) SWP and 600-psig (4140-kPa) CWP ratings.
A. Ferrous-Alloy Ball Valves, General: MSS SP-72, with ASTM A-216 Type WCB, carbon-steel
body; ASTM A-351, Type CF8M vented stainless-steel ball; and ASTM A-276, Type 316
stainless-steel stem; fire rated according to API 607 (4th edition); and having flanged ends and
blowout-proof stem.
B. Class 150, Full-Port, Ferrous-Alloy Ball Valves: Split-body construction, carbon-filled TFE
seats; 285 psig (1964 kPa) CWP rating.
C. Class 300, Full-Port, Ferrous-Alloy Ball Valves: Split-body construction, carbon-filled TFE
seats; 720 psig (4960 kPa) CWP rating.
A. Ferrous-Alloy Butterfly Valves, General: MSS SP-67, for bubble-tight shutoff, extended-neck
for insulation, disc and lining suitable for potable water, unless otherwise indicated, and with
the following features:
1. Full lug, grooved and flanged valves shall be suitable for bi-directional dead end service
at full rated pressure without the use or need of a downstream flange. Valves NPS 12
(DN 300) and smaller shall not have exposed stem to disc fasteners and no exterior
mounted fasteners to hold the liner.
2. Valve sizes NPS 2 through NPS 6 (DN 50 through DN 150) shall have lever lock
operator; valve sizes NPS 8 (DN 200) and larger shall have weatherproof gear operator.
VALVES 15110 - 6
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
VALVES 15110 - 7
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
A. High-Pressure Butterfly Valves, General: MSS SP-68 API 609 seat pressure and temperature
ratings, ANSI B1634A body pressure and temperature ratings, ANSI B16.5 flange dimensions,
ISO 5211, EN 12116 actuator mounting top works, capable of bi-directional dead-end service at
full-rated pressure without use of downstream flange, carbon-steel body, offset design,
extended-neck for insulation, permanently lubricated 300-series stainless-steel bushings with
graphite and modified PTFE seats, graphite packing and gasket, one-piece duplex stainless-steel
stem, and stainless-steel disc. Maximum steam rating of 50 psig (345 kPa). Valves NPS 6 (DN
150) and smaller shall have lever-lock operator; valves NPS 8 (DN 200) and larger shall have
weatherproof gear operator.
B. Single-Flange, Full-Lug, 285 psig (1964 kPa) CWP Rating, High-Pressure Butterfly Valves:
a. Jamesbury, Inc.
b. Xomox Corporation.
C. Single-Flange, Full-Lug, 720 psig (9960 kPa) CWP Rating, High-Pressure Butterfly Valves:
a. Jamesbury, Inc.
b. Xomox Corporation.
VALVES 15110 - 8
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
B. Class 125, Bronze, Lift Check Valves with TFE Disc: ASTM B-584 bronze body and integral
seat with soldered or threaded end connections, and having 250-psig (1378 kPa) CWP rating.
C. Class 125, Bronze, Lift Check Valves with BUNA Disc: ASTM B-584 bronze body and
integral seat with nonmetallic BUNA disc, soldered or threaded end connections, and having
250-psig (1378 kPa) CWP rating.
D. Class 300, Bronze, Swing Check Valves with Bronze Disc: ASTM B-61 bronze body and seat
with regrinding-type bronze disc, Y-pattern design, threaded end connections, and having 600
psig (4134 kPa) CWP rating.
E. Class 125, Bronze, Swing Check Valves with TFE Disc: ASTM B-62 bronze body and seat
with TFE disc in bronze seat holder, Y-pattern design, soldered or threaded end connections, and
having 200 psig (1378 kPa) CWP rating.
F. Class 125, Bronze, Swing Check Valves with BUNA Disc: ASTM B-62 bronze body and seat
with BUNA disc in bronze seat holder, Y-pattern design, soldered or threaded end connections,
and having 200 psig (1378 kPa) CWP rating.
VALVES 15110 - 9
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
G. Class 150, Bronze, Swing Check Valves with TFE Disc: ASTM B-62 bronze body and seat
with TFE disc in bronze seat holder, Y-pattern design, soldered or threaded end connections, and
having 300 psig (2067 kPa) CWP rating.
B. Class 125, Gray-Iron, Standard Swing Check Valves: ASTM A-126, Class B cast-iron body and
bolted bonnet with flanged end connections; non-asbestos synthetic-fiber gaskets; bronze disc
and seat; and having 200 psig (1378 kPa) CWP rating.
C. Class 125, Gray-Iron, Swing Check Valves with Lever and Weight: ASTM A-126, Class B cast-
iron body and bolted bonnet with flanged end connections; non-asbestos, synthetic-fiber
gaskets; bronze disc and seat, lever and weight; and having 200 psig (1378 kPa) CWP rating.
D. Class 250, Gray-Iron, Swing Check Valves: ASTM A-126, Class B cast-iron body and bolted
bonnet with flanged end connections; non-asbestos synthetic-fiber gaskets; and bronze disc and
seat; and having 500 psig (3445 kPa) CWP rating.
E. Grooved-End, Swing Check Valves: Ductile-iron body with grooved or shouldered ends;
nonasbestos, synthetic-fiber gaskets; rubber seats; and having 250-psig (1725-kPa) CWP
Rating.
VALVES 15110 - 10
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
A. Dual-Plate, Iron, Wafer or Grooved Check Valves, General: ANSI B16.1, spring loaded.
B. Dual-Plate, Iron, Wafer or Grooved Check Valves: Class 125, cast-iron, flangeless body with
dual, bronze discs; stainless-steel spring and stop pin; BUNA seat; and having 200 psig (1378
kPa) CWP rating.
a. Metraflex Co.
b. Val-Matic Valve & Mfg. Corp.
A. Lift-Disc Check Valves, General: FCI 74-1 and MIL-V-18436F, with spring-loaded, center-
guided bronze disc and seat.
B. Class 125, Globe, Flanged Lift-Disc Check Valves: Globe style with cast-iron body and flanged
ends, and having 200 psig (1378 kPa) CWP rating.
a. Metraflex Co.
b. Val-Matic Valve & Mfg. Corp.
B. Class 150, Rising-Stem, Union-Ring Bonnet, Bronze Gate Valves: ASTM B-62 bronze body,
bonnet, and wedge, copper-silicone bronze stem, union-ring bonnet, soldered or threaded end
connections; and having 300 psig (2067 kPa) CWP rating.
C. Class 300, Rising-Stem, Stainless-Steel Wedge, Bronze Gate Valves: ASTM B-61 bronze body,
bonnet and seat, stainless-steel wedge and seat, copper-silicone bronze stem, union-ring bonnet,
and threaded end connections; and having 600 psig (4134 kPa) CWP rating.
VALVES 15110 - 11
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
A. Cast-Iron Gate Valves, General: MSS SP-70, Type I with bolted bonnet, flanged end
connections, and non-asbestos packing and gasket.
B. Class 125, OS&Y, Bronze-Mounted, Cast-Iron Gate Valves: ASTM A-126, Class B cast-iron
body and bonnet with bronze trim, and solid-wedge disc; and having 200 psig (1378 kPa) CWP
rating.
C. Class 250, OS&Y, Bronze-Mounted, Cast-Iron Gate Valves: ASTM A-126, Class B cast-iron
body and bonnet with bronze trim, and solid-wedge disc; and having 500 psig (3514kPa) CWP
rating.
B. Class 300, Stainless-Steel Disc, Bronze Globe Valves: ASTM B-61 bronze body and bonnet,
stainless-steel disc and seat, copper-silicone bronze stem, union-ring bonnet, threaded end
connections; and having 600 psig (4134 kPa) CWP rating.
C. Class 150, TFE Disc, Bronze Globe Valves: ASTM B-62 bronze body, bonnet, and seat, TFE
disc, copper-silicone bronze stem, union-ring bonnet, soldered or threaded end connections; and
having 300 psig (2067 kPa) CWP rating.
VALVES 15110 - 12
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
A. Cast-Iron Globe Valves, General: MSS SP-85 with bolted bonnet, flanged end connections, and
non-asbestos packing and gasket.
B. Class 125, Metal Seat, Cast-Iron Globe Valves: ASTM A-126, Class B cast-iron body and
bonnet with bronze trim and having 200 psig (1378 kPa) CWP rating.
C. Class 250, Metal Seat, Cast-Iron Globe Valves: ASTM A-126, Class B cast-iron body and
bonnet with bronze trim and having 500 psig (3445 kPa) CWP rating.
A. Available Manufacturers:
B. Manufacturers:
VALVES 15110 - 13
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
A. Available Manufacturers:
B. Manufacturers:
C. Resilient-Seated, Cast-Iron, Eccentric Plug Valves, NPS 2-1/2 (DN 65) and Smaller: Design
similar to MSS SP-108, and rated for 175-psig (1207-kPa) minimum CWP rating.
D. Resilient-Seated, Cast-Iron, Eccentric Plug Valves, NPS 3 (DN 80) and Larger: MSS SP-108,
and rated for 175-psig (1207-kPa) minimum CWP rating.
A. Available Manufacturers:
B. Manufacturers:
C. Description: Valve actuation assembly with sprocket rim, brackets, and chain.
VALVES 15110 - 14
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
1. Sprocket Rim with Chain Guides: [Ductile iron] [Cast iron] [Aluminum] [Bronze], of
type and size required for valve.[Include zinc coating.]
2. Brackets: Type, number, size, and fasteners required to mount actuator on valve.
3. Chain: [Hot-dip, galvanized steel] [Brass] [Stainless steel], of size required to fit
sprocket rim.
PART 3 - EXECUTION
0.1 EXAMINATION
A. Examine piping system for compliance with requirements for installation tolerances and other
conditions affecting performance.
1. Proceed with installation only after unsatisfactory conditions have been corrected.
B. Examine valve interior for cleanliness, freedom from foreign matter, and corrosion. Remove
special packing materials, such as blocks, used to prevent disc movement during shipping and
handling.
C. Operate valves in positions from fully open to fully closed. Examine guides and seats made
accessible by such operations.
D. Examine threads on valve and mating pipe for form and cleanliness.
E. Examine mating flange faces for conditions that might cause leakage. Check bolting for
proper size, length, and material. Verify that gasket is of proper size, that its material
composition is suitable for service, and that it is free from defects and damage.
A. Refer to piping Sections for specific valve applications. If valve applications are not
indicated, use the following:
B. If valves with specified SWP classes or CWP ratings are not available, the same types of
valves with higher SWP class or CWP ratings may be substituted.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 150, with TFE disc, bronze.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
bronze.
VALVES 15110 - 15
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
5. Butterfly Valves, NPS 2 to NPS 12 (DN 50 to DN 300): Single-flange, full lug, [200-psig
(1380-kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
6. Butterfly Valves, NPS 14 (DN 350) and Larger: Single-flange, full lug, 150-psig (1035-
kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
7. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange, 285 psig
(1964 kPa) CWP rating.
8. Grooved-End, Ductile-Iron Butterfly Valves, NPS 2 to NPS 8 (DN 50 to DN 200) 300-
psig (2070-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
9. Grooved-End, Ductile-Iron Butterfly Valves, NPS 10 to NPS 12 (DN 250 to DN 300):
200-psig (1380-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
10. Lift Check Valves, NPS 2 (DN 50) and Smaller: Class 125, bronze with TFE disc.
11. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 150 , bronze with TFE disc.
12. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast-iron, standard .
13. Grooved-End Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end,
ductile-iron, swing check valves.
14. Dual-Plate Check Valves, NPS 2-1/2 (DN 65) and Larger: Wafer, iron.
15. Spring-Loaded, Center-Guided Lift-Disc Check Valves, NPS 2-1/2 (DN 65) and Larger:
Class 125, flanged end, iron.
16. Gate Valves, NPS 2 (DN 50) and Smaller: Class 150 , rising stem, union-ring bonnet,
bronze trim, solid wedge, bronze.
17. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, OS&Y, bronze mounted, cast
iron.
18. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
19. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
20. Plug Valves, NPS 2 (DN 50) and Larger: Class [125 or 150] [250 or 300], [lubricated]
[nonlubricated]-type, cast iron.
21. Resilient-Seated, Eccentric Plug Valves, NPS 3 (DN 80) and Larger: 175-psig (1207-
kPa) CWP rating, cast iron.
1. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, bronze trim, bronze.
2. Equipment-Isolation Ball Valves, NPS 2 (DN 50) and Smaller: Safety-exhaust, bronze.
3. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
4. Butterfly Valves, NPS 2 to NPS 12 (DN 50 to DN 300): Single-flange, full lug, 200-psig
(1380-kPa) CWP rating, bronze disc, BUNA liner, ferrous alloy.
5. Butterfly Valves, NPS 14 (DN 350) and Larger: Single-flange, full lug, 150-psig (1035-
kPa) CWP rating, bronze disc, BUNA liner, ferrous alloy.
6. Grooved-End, Ductile-Iron Butterfly Valves, NPS 2 to NPS 8 (DN 50 to DN 200):300-
psig (2070-kPa) CWP rating, BUNA-encapsulated ductile-iron disc.
7. Grooved-End, Ductile-Iron Butterfly Valves, NPS 10 to NPS 12 (DN 250 to DN 300):
200-psig (1380-kPa) CWP rating, BUNA-encapsulated ductile-iron disc.
8. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange full lug,
285 psig (1964 kPa) CWP rating.
9. Lift Check Valves, NPS 2 (DN 50) and Smaller: Class 125, bronze with BUNA disc.
10. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 125 , BUNA, bronze.
11. Grooved-End, Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end,
ductile-iron swing check valves.
12. Dual-Plate Check Valves, NPS 2-1/2 (DN 65) and Larger: Wafer, Class 125 iron.
VALVES 15110 - 16
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
13. Spring-Loaded, Center-Guided, Lift-Disc Check Valves, NPS 2-1/2 (DN 65) and Larger:
Class 125, flanged end, iron.
14. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
1. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, bronze trim, bronze.
2. Equipment-Isolation Ball Valves, NPS 2 (DN 50) and Smaller: Safety-exhaust, bronze.
3. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
4. Butterfly Valves, NPS 2 to NPS 12 (DN 50 to DN 300): Single-flange, full lug, 200-psig
(1380-kPa) CWP rating, bronze disc, BUNA liner, ferrous alloy.
5. Butterfly Valves, NPS 14 (DN 350) and Larger: Single-flange, full lug, 150-psig (1035-
kPa) CWP rating, bronze disc, BUNA liner, ferrous alloy.
6. Grooved-End, Ductile-Iron Butterfly Valves, NPS 2 to NPS 8 (DN 50 to DN 200): 300-
psig (2070-kPa) CWP rating, BUNA-encapsulated ductile-iron disc.
7. Grooved-End, Ductile-Iron Butterfly Valves, NPS 10 to NPS 12 (DN 250 to DN 300):
200-psig (1380-kPa) CWP rating, BUNA-encapsulated ductile-iron disc.
8. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange full lug,
285 psig (1964 kPa) CWP rating.
9. Lift Check Valves, NPS 2 (DN 50) and Smaller: Class 125 bronze with BUNA disc.
10. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
11. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end, ductile-iron swing
check vavles.
12. Dual-Plate Check Valves, NPS 2-1/2 (DN 65) and Larger: Wafer, iron.
13. Spring-Loaded, Center-Guided, Lift-Disc Check Valves, NPS 2-1/2 (DN 65) and Larger:
Class 125, flanged end, iron.
14. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 150, with TFE disc, bronze.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
bronze.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
5. Butterfly Valves, NPS 2 to NPS 12 (DN 50 to DN 300): Single-flange, full lug, 200-psig
(1380-kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
6. Butterfly Valves, NPS 14 (DN 350) and Larger: Single-flange, full lug, 150-psig (1035-
kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
7. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange, 285 psig
(1964 kPa) CWP rating.
8. Grooved-End, Ductile-Iron Butterfly Valves, NPS 2 to NPS 8 (DN 50 to DN 200): 300-
psig (2070-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
9. Grooved-End, Ductile-Iron Butterfly Valves, NPS 10 to NPS 12 (DN 250 to DN 300):
200-psig (1380-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
10. Lift Check Valves, NPS 2 (DN 50) and Smaller: Class 125, bronze with TFE disc.
11. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 150 , bronze with TFE disc.
12. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron, standard .
13. Grooved-End Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end,
ductile-iron, swing check valves.
14. Dual-Plate Check Valves, NPS 2-1/2 (DN 65) and Larger: Wafer, iron.
VALVES 15110 - 17
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
15. Spring-Loaded, Center-Guided, Lift-Disc, Iron Check Valves, NPS 2-1/2 (DN 65) and
Larger: Class 125, flanged end, iron.
16. Gate Valves, NPS 2 (DN 50) and Smaller: Class 150, rising stem, union-ring bonnet,
bronze trim, solid wedge, bronze.
17. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, OS&Y, bronze mounted, cast
iron.
18. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
19. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
20. Plug Valves, NPS 2 (DN 50) and Larger: Class [125 or 150] [250 or 300], [lubricated]
[nonlubricated]-type, cast iron.
21. Resilient-Seated, Eccentric Plug Valves, NPS 3 (DN 80) and Larger: 175-psig (1207-
kPa) CWP rating, cast iron.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 150, with TFE disc, bronze.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
bronze.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
5. Butterfly Valves, NPS 2 to NPS 12 (DN 50 to DN 300): Single-flange, full lug, 200-psig
(1380-kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
6. Butterfly Valves, NPS 14 (DN 350) and Larger: Single-flange, full lug, 150-psig (1035-
kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
7. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Smaller: Single-flange full lug,
285 psig (1964 kPa) CWP rating.
8. Grooved-End, Ductile-Iron Butterfly Valves, NPS 2 to NPS 8 (DN 50 to DN 200): 300-
psig (2070-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
9. Grooved-End, Ductile-Iron Butterfly Valves, NPS 10 to NPS 12 (DN 250 to DN 300):
200-psig (1380-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
10. Lift Check Valves, NPS 2 (DN 50) and Smaller: Class 125 , bronze with TFE disc.
11. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 150 , bronze with TFE disc.
12. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast-iron, standard .
13. Grooved-End Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end,
ductile-iron, swing check valves.
14. Dual-Plate Check Valves, NPS 2-1/2 (DN 65) and Larger: Wafer, iron.
15. Spring-Loaded, Center-Guided, Lift-Disc Check Valves, NPS 2-1/2 (DN 65) and Larger:
Class 125, flanged end, iron.
16. Gate Valves, NPS 2 (DN 50) and Smaller: Class 150 , rising stem, union-ring bonnet,
bronze trim, solid wedge, bronze.
17. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, OS&Y, bronze-mounted, cast
iron.
18. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
19. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
20. Plug Valves, NPS 2 (DN 50) and Larger: Class [125 or 150] [250 or 300], [lubricated-
type with FDA-approved-material sealant] [nonlubricated-type], cast iron.
21. Resilient-Seated, Eccentric Plug Valves, NPS 3 (DN 80) and Larger: 175-psig (1207-
kPa) CWP rating, cast iron.
VALVES 15110 - 18
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 150, with TFE disc, bronze.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
copper alloy.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
5. Butterfly Valves, NPS 2 to NPS 12 (DN 50 to DN 300): Single-flange, full lug, 200-psig
(1380-kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
6. Butterfly Valves, NPS 14 (DN 350) and Larger: Single-flange, full lug, 150-psig (1035-
kPa) CWP rating, bronze disc, EPDM liner, ferrous alloy.
7. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange, 285 psig
(1964 kPa) CWP rating.
8. Grooved-End, Ductile-Iron Butterfly Valves, NPS 2 to NPS 8 (DN 50 to DN 200): 300-
psig (2070-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
9. Grooved-End, Ductile-Iron Butterfly Valves, NPS 10 to NPS 12 (DN 250 to DN 300):
200-psig (1380-kPa) CWP rating, EPDM- encapsulated ductile-iron disc.
10. Lift Check Valves, NPS 2 (DN 50) and Smaller: Class 125, bronze with TFE disc.
11. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 150 , bronze with TFE disc.
12. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron, standard .
13. Grooved-End Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end,
ductile-iron, swing check valves.
14. Dual-Plate Check Valves, NPS 2-1/2 (DN 65) and Larger: Wafer, iron.
15. Spring-Loaded, Center-Guided, Lift-Disc Check Valves, NPS 2-1/2 (DN 65) and Larger:
Class 125, flanged end, iron.
16. Gate Valves, NPS 2 (DN 50) and Smaller: Class 150 , rising stem, union-ring bonnet,
bronze trim, solid wedge, bronze.
17. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, OS&Y, bronze-mounted, cast
iron.
18. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
19. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
I. [Sanitary Waste] [and] [Storm Drainage] Piping: Use the following types of valves:
1. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
bronze.
2. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
3. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 125 , bronze with TFE disc.
4. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron, standard .
5. Grooved-End Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Grooved-end,
ductile-iron, swing check valves.
6. Gate Valves, NPS 2 (DN 50) and Smaller: Class 150 , rising stem, union-ring bonnet,
bronze trim, solid wedge, bronze.
7. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, OS&Y, bronze-mounted, cast
iron.
8. Globe Valves, NPS 2 (DN 50) and Smaller: Class 150 , TFE disc, bronze.
9. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
10. Plug Valves, NPS 2 (DN 50) and Larger: Class 125 or 150, [lubricated]
[nonlubricated]-type, cast iron.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 300, with stainless-steel disc, bronze.
VALVES 15110 - 19
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
bronze.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 150, full -port, ferrous alloy.
5. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange 285 psig
(1964 kPa) CWP rating.
6. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 150 , bronze with TFE disc.
7. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, , cast-iron, standard .
8. Gate Valves, NPS 2 (DN 50) and Smaller: Class 150 , rising stem, union-ring bonnet,
bronze trim, solid wedge, bronze.
9. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 125, OS&Y, bronze-mounted, cast
iron.
10. Globe Valves, NPS 2 (DN 50) and Smaller: Type 2, Class 150 , TFE disc, bronze.
11. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 125; cast iron.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 300; with stainless-steel disc, bronze.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Class 250, Two -piece, full port, stainless-steel
trim, bronze.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 300, full -port, ferrous alloy.
5. High-Pressure Butterfly Valves, NPS 3 (DN 80) and Larger: Single-flange 720 psig
(4960 kPa) CWP rating.
6. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 300, bronze with bronze disc.
7. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, cast-iron, standard .
8. Gate Valves, NPS 2 (DN 50) and Smaller: Class 300, rising stem, union-ring bonnet,
stainless-steel trim, solid wedge, bronze.
9. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, OS&Y, bronze-mounted, cast
iron.
10. Globe Valves, NPS 2 (DN 50) and Smaller: Class 300, stainless-steel disc, bronze.
11. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, cast iron.
1. Angle Valves, NPS 2 (DN 50) and Smaller: Class 300, stainless-steel disc, bronze.
2. Angle Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, cast iron.
3. Ball Valves, NPS 2 (DN 50) and Smaller: Two -piece, full port, stainless-steel trim,
bronze.
4. Ball Valves, NPS 2-1/2 (DN 65) and Larger: Class 300, full -port, ferrous alloy.
5. High-Pressure Butterfly Valves, NPS 2-1/2 (DN 65) and Larger: Single-flange, 720 psig
(4960 kPa) CWP rating.
6. Swing Check Valves, NPS 2 (DN 50) and Smaller: Class 300, bronze with bronze disc.
7. Swing Check Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, gray iron, standard .
8. Gate Valves, NPS 2 (DN 50) and Smaller: Class 300, rising stem, union-ring bonnet,
stainless-steel trim, solid wedge, bronze.
9. Gate Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, OS&Y, bronze-mounted, cast
iron.
10. Globe Valves, NPS 2 (DN 50) and Smaller: Class 300, stainless-steel disc, bronze.
11. Globe Valves, NPS 2-1/2 (DN 65) and Larger: Class 250, cast iron.
VALVES 15110 - 20
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
12. Plug Valves, NPS 2 (DN 50) and Larger: Class [125 or 150] [250 or 300], [lubricated]
[nonlubricated]-type, cast iron.
M. Select valves, except wafer and flangeless types, with the following end connections:
1. For Copper Tubing, NPS 2 (DN 50) and Smaller: Solder-joint or threaded ends, except
provide valves with threaded ends for [condenser water,] heating hot water, steam, and
steam condensate services.
2. For Copper Tubing, NPS 2-1/2 to NPS 4 (DN 65 to DN 100): Flanged [soldered or
threaded] ends.
3. For Copper Tubing, NPS 5 (DN 125) and Larger: Flanged ends.
4. For Steel Piping, NPS 2 (DN 50) and Smaller: Threaded ends.
5. For Steel Piping, NPS 2-1/2 to NPS 4 (DN 65 to DN 100): Flanged [or threaded] ends.
6. For Steel Piping, NPS 5 (DN 125) and Larger: Flanged ends.
7. For Grooved-End, [Copper Tubing] [and] [Steel Piping]: Valve ends may be grooved.
Do not use for steam or steam condensate piping.
B. Install valves with unions or flanges at each piece of equipment arranged to allow service,
maintenance, and equipment removal without system shutdown.
C. Locate valves for easy access and provide separate support where necessary.
D. Install valves in horizontal piping with stem at or above center of pipe. Butterfly valves may
be installed with stem horizontal to allow support for the disc and the cleaning action of the
disc.
F. Install chainwheel operators on valves [NPS 4 (DN 100)] <Insert other> and larger and more
than [84 inches (2100 mm)] <Insert other> above floor. Extend chains to [60 inches (1520
mm)] <Insert other> above finished floor elevation.
A. Refer to Division 15 Section "Basic Mechanical Materials and Methods" for basic piping joint
construction.
VALVES 15110 - 21
Copyright 1999 AIA MASTERSPEC 6/99
PRODUCT MASTERSPEC LICENSED BY ARCOM TO NIBCO, INC.
B. Grooved Joints: Assemble joints with keyed coupling housing, gasket, lubricant, and bolts
according to coupling and fitting manufacturer's written instructions.
C. Soldered Joints: Use ASTM B 813, water-flushable, lead-free flux; ASTM B 32, lead-free-
alloy solder; and ASTM B 828 procedure, unless otherwise indicated.
0.5 ADJUSTING
A. Adjust or replace valve packing after piping systems have been tested and put into service but
before final adjusting and balancing. Replace valves if persistent leaking occurs.
VALVES 15110 - 22