104
Ge
WIRE ROPE CLIPS
BENEFITS & FEATURES:
+ Precision manufactured and galvanized
to meet federal specifications
(FF-C-450 Type 1 Class 1) on 1/4"
and larger
* Drop forged base
t
va) 50 | Mass [ve-2amc| 072 | oat | oa? | oa2 | 038
ane | 50 | was | zoe) os | oss | 059 | os | 050
| 50 | Meas |ss-raunc) 103 | 05 | 075 | 96 | o56
sme | 50 | wor | sotoinc) 150 | 075 | oss | o7 | 68
‘ap | so | wows (7nesanc| 150 | 075 | 100 | as | a75
me | 50 | mama |setmmc) 1a | too | aso | 108 | oe
v2 | 2 | meso | veramc) 168 | to | 119 | 416 | oe
ss | 2 | mse jane-ramc| 2a | 125 | tat | izs | oo
se | 20 | wast one-ainc| 238 | 125 | 131 | 1 | aoe
au | 10 | masa |sernmc| 275 | 14 | 150 | tae | tos
me | 10 | mass autounc) 313 | 16s | 175 | 16a | 125
1 | 10 | wast |ausome| sso | 181 | tae | ize | ta
reve) 5 | mass |se-10mc | 388 | 200 | 200 | ran | 1.25
va || mas | rmouec | 42s | ann | am | am | tae
rye) 5 | wasr | eo | aes | 2m | 2m | 225 | 144
sve | 5 | ose | rmounc | aoe | 238 | 250 | 250 | tae
NOTE: VB" wea 9/8" paced ee per go Ong, 24" & rer hoped assem in factory packs nd tapped
PROPER USE OF WIRE ROPE CLIPS
Reter to the chart above when folowing these instructions. Turn back specified
‘amount of rope from thimble or loop. APP frst clip one base width from dead
end of rope. Apply U-bolt over dead end of wire rope, ensuring live end rests in
Saddle. Tighten nuts evenly, alternate from one nut to the other until reaching the
commended torque,
nen two clips are required, apply the second clip as near the thimble or loop
as possible. Tighten nuts evenly, alternating unt reaching the recommended
torque. When more than two clips are required, apply the second clip as near
the loop or thimble as possible and turn nuts on second clip fly, But do not
tighten: Proceed to Step 3,
3 When three or more clips are required, space additional clips equally between
the first two and take up rope slack. Then tighten nuts on each U-bolt evenly,
alternating from one nut to the other until reaching the recommended torque.
4. Apply an intial load equal to loads expected in use. Inspect for proper
‘orientation and spacing of clips and retighten the nuts to recommended torque,
care INSPECTION
* Care should be exercised inthe installation * Visually inspect wire
and use of wire rope clips so that the clip, rope clips
‘ire rope, or thimble is not damaged before each use,
* Do not over torque of under torque the nuts, * Be certain threads are
“Too much torque can result in damage to the not stripped and that
cilp andor the wire rope. Too ile torque can ruts are tight.
result in the wire rope slipping. Torque nuts * Check torque of nuts
to the value specified in the accompanying periodical.
instructions. + Replace distorted thimbles,
* Clips should not be subjected to bending + Shorten wire rope and form
for come in contact with sharp object.
now loop if damaged
* Avoid exposure to corrosive mediums. . ”
Replace distorted thimbles.
eve) 3a) aoe
19 re | 304 | on
tat
169
194
2a
231
20
28
a6
aa
350
az
425
Sago
NEVER INSTALL THE U-BOLT
‘ON THE LIVE SIDE!
IMPROPER USE
(OF WIRE ROPE CLIPS =
WW.CMWORKS.COM