Professional Documents
Culture Documents
DESCRIPTION
Bostik Seal ‘N’ Flex FC is a fast cure high performance
one component polyurethane elastomeric joint sealant.
When fully cured, Seal ‘N’ Flex FC will provide a tough,
flexible seal capable of cyclic expansion and compression
to 50% of original joint width without primer on most
substrates. Seal ‘N’ Flex FC is unaffected by ultra-violet
radiation, atmospheric contamination or pollution. Its
excellent weatherability enables it to retain its original
properties after years of exposure (C.S.I.R.O. RILEM
exposure study.
Place the cartridge in a suitable Bostik extrusion gun and Technology Aromatic
press the trigger. For sausages, a barrel gun is required, Appearance Non-sag smooth
this is available from Bostik. Clip the end of the sausage thixotropic paste
and place complete sausage with pierced end located at Cure System Moisture curing
the top o the nozzle. Screw top of nozzle and housing
on barrel of gun. Using the trigger on the gun extrude Tack free time (minutes) 45 minutes
product from the sausage to stop product flow, using Rate cure in mm/24 hrs 3.5
the thumb depress the catch plate mechanism located at
the very rear of the gun, directly above the trigger. Apply Hardness shore A 50 + 5%
Seal ‘N’ Flex FC in a continuous operation using positive Tensile Strength > 2.1 N/mm2
pressure adequate to properly fill and seal a cavity.
Application temperature 5 C to 35 C
Construction Adhesive Applications Temperature Resistance -40 C to +70 C
Seal ‘N’ Flex FC does not need to be applied to both Color Grey, black and white
surfaces to be bonded, but both surfaces, must be Full cure Depends on thickness (e.g.
prepared in accordance with preparatory work. 10mm will cure 3 days
approx.)
Apply in beads or daubs to the prepared substrate.
Materials being adhered can be bonded immediately *Average laboratory values provided as a general guide
**Actual field performance will depend on installation and site conditions
or left open for up to 15 minutes after application prior
to bonding. If no mechanical fixing is to be used in PRECAUTION
conjunction with adhesive, clamping is necessary until • Seal ‘N’ Flex FC should not be used in highly
full cure is achieved. Use only enough sealant to achieve chlorinated areas such as swimming pools, spas etc.
adequate bond (dependant on surface texture). Excess without prior consultation with Bostik Technical
sealant can be removed by dry cloth or solvent wipe Services
before curing. • Seal ‘N’ Flex FC should not be used in glazing
applications subject to UV light radiation or direct
If adhesive is to be exposed, smooth off with spatula or
sunlight exposure without prior consultation with
putty knife to flush finish.
Bostik
Construction Sealant/Adhesive Applications • Seal ‘N’ Flex FC should not be applied or finished with
wet tooling techniques, using solvents, water or
Seal ‘N’ Flex FC is especially suitable for vertical joint
detergent/soap solutions
sealing or in flooring applications such as saw cuts,
• Seal ‘N’ Flex FC sealant should not be applied to
jointing. More joint movement can be accommodated
unpredictable absorptive surfaces such as marble,
in a thin bead of sealant than in a thick bead. The
limestone or granite unless a standard of appearance
ratio of joint width of sealant to depth should be
has been agreed on as a result of testing for stain
2:1. The use of a bond breaker prevents undesirable
and/or discoloration.
three-sided-adhesion. Open cell polyurethane foam or
• Do not use in interior or exterior structural sealing
closed cell polyethylene foam rod is the recommended
below the waterline in marine applications
back up material to control correct sealant geometry.
• Do not apply at temperature below 5 C
Install back up material or joint filler, as specified. Apply • Do not apply to surfaces with special protective or
Seal ‘N’ Flex FC continuously using positive pressure cosmetic coating such as mirrors, reflective glass
to properly fill and seal the joint. Tool the sealant with or surfaces coated with Teflon, polyurethane or
adequate pressure to spread the sealant against the polypropylene. Will not adhere to polyethylene,
back up material and onto the joint sides. Excess sealant polypropylene or PTFE.
should be wiped from all surfaces while still uncured.
Remove any masking tapes prior to sealant curing PAINTABILITY
Bostik Seal ‘N’ Flex FC can be painted as early as 24
PACKAGING
hours after application using water borne coating and
Seal ‘N’ Flex FC is supplied in 380gm (300ml) cartridges most epoxy flooring systems. Coatings containing
and 720gm (600ml) sausages, 20 per carton. high solvent contents such as gloss enamels or high
oil based undercoats may cause the surface of the
COVERAGE
sealant to react creating a tacky surface to develop. A
Pack Size Lineal metres Lineal metres field test is recommended to ensure compatibility. To
6mm bead 20mm bead obtain best appearance and performance the paint must
380 gm ct (300ml) 10 2.3 approximate the elongation capabilities of the sealant.
720 gm sgs. (600ml) 19 44 High build coatings with some elastomeric ability such
as quality acrylic emulsions have the capability to absorb
low movement without significant distortion of the
paint film. Please contact Bostik Technical Department
if unsure of any paint system. DISCLAIMER:
The information in this Technical Data Sheet is intended for the assistance
P.A.T.S (Pretested Adhesion to Substrate) of users and is of a general nature. It reflects the extent of our knowledge
and experience of our products and is based on tests which we believe to be
Programme reliable. However, no guarantee of accuracy can be given due to the wide range
of surfaces, environmental and field conditions and variations encountered in
Bostik offer a service in which a program has been
raw materials, manufacturing equipment and methods at the place where the
established to eliminate potential field problems by work is performed. Some of these will be beyond our knowledge and control.
Users are asked to make sure that the TDS in their possession is the latest issue.
pre-testing Bostik adhesives with samples of building
Likewise, we recommend users carry out their own tests to determine the
materials to which the adhesive will be applied. suitability of the product for their particular purposes.
This service is available on large projects where Any claim for a defective product must be filed within 30 days of discovery of
pre-application testing will aid in determining the a problem and must be submitted with written proof of purchase. Claims are
not transferrable or assignable and extend only to the original purchaser/user.
proper surface preparation method to achieve optimum Bostik reserves the right to inspect alleged failure and no responsibility will be
adhesion. Consult a Bostik representative for further accepted unless Bostik is given the opportunity to do so. Bostik limits its liability
to the replacement of the product/s proven faulty.
information. the capability to absorb low movement
HEALTH AND SAFETYant distortion of the paint film.
FIRE
Seal ‘N’ Flex FC is non-flammable
BOSTIK HOTLINE
BOSTIK PHILIPPINES, INC.
35/F Penthouse Raffles Corporate Center
F. Ortigas Jr. Road, Ortigas Business Center Smart help +63 2 900 5656
Pasig City Philippines
Tel No: +63 2 900 5856 | Fax: +63 2 900 5616