Service Parts Information
Model 34 Winch
2) Tulsa Winch*34-SLLRO
tem | _Devcripton [Qh] Od | Curent ftom [__ Description Om | Curent
1 | Dowel Pin 3 20517 46 | CapScrew | 10 | 20276 | 20276
2 | Bushing 4 | 20173 | 32842 47 | Bracket 1 | 20284 | 20284
3 | Cap Screw 4 | 20266 | 20266 48 | Key 4 | 20105 | 20105
4 | Grease Fiting | 5 |... | 21128 49 | CapScrew | 1 | 20278 | 20278
5 | Cap 4 | 20083 | 20053 50 | Washer 1 | 20092 | 20092
6 | Bracket 1 | 20256 | 20256 st | Cap 1 | 21542 | 21542
7 | Bracket 4 | 20129 | 20129 52 | Gasket 2 | 20118 | 20118
& | DrumBrake | 1 | SA1741 | SA1741 3 | Cam 4 | 23875 | 29875
9 | Set Screw 2 | 20515 | 20515 54 | Bearing 2 | 20303 | 20303
10 | Washer 2 | 20096 | 20096 55 | Seal 2 | 20281 | 20281
41 | Clutch 1 | 20262 | 20262 86 | CapScrew | 16 | 90205 | 30205
12 | Clutch 1 | 23598 | 23598 87 | WormRH. 1 | 21641 | 21641
13 | Cap Screw 6 | 20407 | 20407 Worm LH. 1 | 21640 | 21640
14 | Drum 1 | 23695 | 23595 58 | Key 1 | 25393 | 25393
15 | UBot 1 | 21154 | 21154 59 | CapScrew | 8 | 30202 | 939262
60 | Bushing 2 | 32711 | 32840
16 | CapScrew | 5 | 20270 | 20270
17 | DriveScrew | 4 | 21775 | 21775 61 | Housing 1 | 21556 | 21556
18 | NamePlate | 1 | 21184 | 21184 62 | LockWasher | 8 | 20520 | 20520
19 | LockWasher | 8 | 20518 | 20518 63 | Nut 8 | 20274 | 20274
20 | Nut 9 | 20267 | 20267 64 | Pipe Plug 3 | 20286 | 20286
65 | Frame LH. 1 | 20292 | 939269
21 | Nut 5 | 20521 | 20521
22 | Spring 1_| 20958 | 20958 66 | Frame RH. 1 | 20293 | 20293
23 | LockWasher | 16 | 20526 | 20526 67 | Koy 2 | 20098 | 20098
24 | Nut 45 | 20271 | 20271 68 | Shaft 4 | 25493 | 22443
25 | Rod 4 | 20112 | 20112 69 | Bushing 2 | 20169 | 32839
70 | Key 2 | 20874 | 20574
26 | Cap Screw 2 | 20520 | 170177
27 | Arm + | 20094 | 20094 71 | GapScrew | 10 | 21157 | 21157
28 | Clevis 1 | 20054 | 20054 72 | Carrier 2 | 22438 | 22438
29 | Washer 4 | 20617 | 20617 73 | Spacer 4 | 20569 | 20569
30 | Cap Screw 4 | 28578 | 28578 74 | Dowel Pin 2 | 20509 | 164056
75 | GearRH. 1 | 21643 | 21643
31 | Housing 1 | 21365 | 21365 Gear LH 1 | 21642 | 21642
32 | Cotter Pin 1 | 20514 | 20514
33 | levis Pin 1 | 20633 | 939243 76 | Cover 1 | 20127 | 20127
34 | Arm 2 | 20070 | 20070 77 | Breather 1 | 26799 | 26799
5 | Shaft 2 | 20282 | 20282 78 | CapScrew | 4 | 20268 | 20268
79 | Gasket 2 | 20326 | 20326
436 | DriveScrew | 9 80 | LockWasher | 10} 20519 | 20519
37 | Set Screw 4 | 20193 | 20193
38 | Collar 4 | 20230 | 20280 ai | Nut 10 | 20273 | 20273
39 | Yoke 4 | 20264 | 20264 2 | Key 1 | 20279 | 20279
40 | Snap Ring 2 | bare4 | bazea 83 | BrakeDrum | 1 | 29503 | 29503
84 | LockWasher | 1 | 20115 | 20115
41 | Pin 1 | 20116 | 20116 8 | Lock Nut 1 | 20114 | 20114
42 | Set Screw 2 | 20737 | 20737
43 | Cotter Pin 2 | 20074 | 20474 86 | Brake Shoe | 2 | $A1733 | Sai733
44 | Rod RH" 1 | 20111 | 20111 87 | CamPiate 1 | Sasses | Sa3568
Rod LH, 1 | 20113 | 20113 | [+88 | instruction
45 | Arm 1 | 20072 | 20072 Plate 1
{Part of $A3568 Cam Plate.
PicturesModel —-— SUE Se GE 8. ee Ee L R °
= TYPEUNIT SERIES TYPE WORM WORM ANGLE GEARBOX LOCATION INPUT SHAFT LOCATION _ CABLE SPOOL
Code: Omiritdesicuny 54" Mode! D=Doublelead L = Left (From Behind Truck) (Relating to Truck) 0 = Over Drum
G=Speed Reducer F=FlushShait S=SingleLead A=Right bet F = Front U= Under Orum
R= Right R= Rear
Moving
z Not Approved for Lifting or People!
Read Operating and Safety Manual Before Using Any Winch!BRAKE ADJUSTMENT
FREQUENCY: Brake adjustment should be checked dally during
heavy use or after one (1) nour of winch operation. Inspection of
Dako shoes and drum for woar should be made after every ten (10)
hours of winch operation.
PROCEDURE:
To Adjust Brakes:
1 Remove load from winch cable.
2 Remove sprocket, coupler, universal Joint, or motor trom input
shat of winch,
‘ote: It power source to winch requires no appreciable torque
totum in-a “Neutral” or "OM" position and an adaptor
an be made to ft the coupling, this step le not necessary.
3. Using a suitable adapter, place a torque wrench on the Input
‘shaft of the winch (87)
4.Moasure torque while turning the Input shat in the payout ai-
rection. Torque seltings should be as follows:
‘Model Torque (bt)
34 70
Note: The torque value above Is necessary to brake the rated
oad of the winch. In no caso shaula the brake setting
‘ver be Increased above this torque value.
‘5. To adjust the brake torque, loosen the two cap screws (28) and
fotate the cam (63). To incroace tho brake seting, rotate away
from the "0" or center setting, To reduce the brake seting, To
tate the cam back toward the “0” or center setting,
8, Recheck the torque value as indicated In 4. above.
To Inspect or Repair Brakes:
1. Loosen and remove cap screws (26) and washers (29) trom
brake assembly.
Tulsa Winch, Inc.
PO Box 1130
Jenks, OK 74037
918-298-8300
918-298-8301 (tax)
‘wow tulsawineh com
sales @tulsawinch com
2, Gently pry the cam (53) out of the cover (87)
Caution: Be sure to note which set of drilled and tapped holes
were used t0 position the cam. Failure to re-intall tho
{amin this position will result in the brake engaging In.
the inhaul rather than the payout mode.
'8.Remove the cap scrows (80) from the cover (87).
4. Remove the cover (67) from the brake housing (21)
5. The brake shoes (86) may now be removed for inspection
6.If the shoe linings are worn flush with the rivet heads, they
should be replaced.
7. Inspect the drum (83) for severe wear or scoring, 1 necessary,
lace the drum.
8. To remove the brake drum, remove the nut (86) and washer (84)
8. Insert two cap screws in the holes provided In the brake drum
nd, using a gear puller, remove tho drum.
410. Inspsct the Inside lower part of the brake housing for the pre-
sence of ol. an oll leak exists, replace the seal (35)
To Change Direction of Brake Engagement:
{. Remove cap screws (28) and washers (20).
2.Rolate cam (53) In either direction until enother set of drlled
{nd tapped holes becomes visible through the slots in the cam,
3: Reinstall the cap serews (26) and washers (2) In these tapped
4, Adjust brake as described above.
Caution: Any change in winch mounting, direction of cable
Paling. oF replacement of worm and gear may etfect
the operation of the brake. It you have ary question about
the performance of the brake on your Tulsa
Winch, stop using it immediately and. contact Tul
‘Winch’ er one o our authorized dietbutors
07.01 1M