Professional Documents
Culture Documents
CCNA 4 v6 ScaN EIGRP Practice Skills Assessment Answers
CCNA 4 v6 ScaN EIGRP Practice Skills Assessment Answers
February 24,
2017
Type A
Type B
Type C
Introduction
In this practice skills assessment, you will configure the Major City network with EIGRP
1/39
routing and enhanced switching. The network is configured with both IPv4 and IPv6 on all
devices. This will allow you to implement routing in both EIGRP for IPv4 and EIGRP for IPv6.
Your goal is to achieve full connectivity between all LAN hosts and the remote Town Server
in both IPv4 and IPv6. For a full list of tasks, see below.
You are not required to configure the following:
• The Primary network switches
• Most of the network hosts and the Town Server
• The Town Cloud
All IOS device configurations should be completed from a direct terminal connection
to the device console.
You will practice and be assessed on the following skills:
• Configuration of IPv4 and IPv6 default routes
• Configuration of EIGRP for IPv4
• Configuration of EIGRP for IPv6
• Customization of EIGRP for IPv4 and EIGRP for IPv6
You will configure specific devices with the following:
Router Ed_Dept:
• IPv4 and IPv6 default route
• EIGRP for IPv4 and EIGRP for IPv6
• Router ID
• Interface bandwidth
• Redistribution of default routes
Router Primary-1:
• EIGRP for IPv4 and EIGRP for IPv6
• HSRP
• Interface bandwidth
• EIGRP for IPv4 passive interface
Router Primary-2:
• IPv4 default route
• HSRP
Router High_School:
• EIGRP for IPv4 and EIGRP for IPv6
• Router ID
• Interface bandwidth
• EIGRP for IPv4 passive interfaces
Switch Dist-1:
• RPVST+ activation
• RPVST primary root bridge priority
• EtherChannel channel groups
• Static trunking with native VLAN
• DTP
2/39
• VTP
Switch Acc-1:
• RPVST+ activation
• PortFast
• BPDU Guard
• EtherChannel channel groups
• Static trunking with native VLAN
• DTP
• VTP
Switch Acc-2:
• RPVST+ activation
• RPVST secondary root bridge priority
• EtherChannel channel groups
• Static trunking with native VLAN
• DTP
• VTP
PC PC-A:
• Default gateway
PC PC-M:
• Default gateway
Addressing Table
Use the following addresses to configure the network. Some addresses are preconfigured
on devices that you are not required to configure, and are provided for reference purposes
only.
S0/0/1 192.168.100.21/30
2001:DB8:1B::1/64
FE80::1 link local
S0/1/0 203.0.113.18/30
2001:DB8:99::2/64
FE80::1 link local
3/39
Primary-1 S0/0/0 192.168.100.10/30
(Hospital_1)
(CCNAv6.com) 2001:DB8:1A::2/64
FE80::2 link local
S0/0/1 192.168.100.33/30
2001:DB8:2::1/64
FE80::2 link local
G0/0 10.1.0.3/24
2001:DB8:20::3/64
FE80::2 link local
G0/0 10.1.0.2/24
2001:DB8:20::2/64
FE80::22 link local
S0/0/1 192.168.100.22/30
2001:DB8:1B::2/64
FE80::3 link local
S0/1/0 2001:DB8:E::2/64
G0/0.10 10.10.0.1/24
2001:DB8:3:10::1/64
FE80::3 link local
G0/0.15 10.15.0.1/24
4/39
2001:DB8:3:15::1/64
FE80::3 link local
G0/0.20 10.20.0.1/24
2001:DB8:3:20::1/64
FE80::3 link local
Instructions
Requirements:
1. Configure router Primary-1 with HSRP as follows:
- The group number is 1.
- Virtual gateway IP address: 10.1.0.1
- The router should immediately become the active router.
- The priority should be 150.
2. Configure router Primary-2 as follows:
- Virtual gateway IP address: 10.1.0.1
6/39
- Leave all other HSRP values at the default.
3. In order for the Primary-2 router to provide connectivity to the Internet, it requires a
default route to be configured as you are directed in Step 1-1 above. This router is not
configured with EIGRP.
4. Configure hosts PC-A and PC-M with the correct default gateway addresses.
1 Dist-1 Fa0/3
Fa0/4
Acc-1 Fa0/3
Fa0/4
2 Dist-1 Fa0/5
Fa0/6
Acc-2 Fa0/5
Fa0/6
3 Acc-1 Fa0/1
Fa0/2
Acc-2 Fa0/1
Fa0/2
1. Configure EtherChannels with the LACP protocol using the information in the table.
2. Both sides of the channel should ask if the other side is willing to participate in the
channel.
Step 2-2: Configure Trunking.
Configure trunking as follows:
1. The trunk between High_School and Dist-1 should be active.
2. The trunk between High_School and Dist-1 should use the native VLAN value
preconfigured on High_School.
3. Configure all of the port channel interfaces as static trunks with the appropriate native
VLAN.
4. Disable DTP negotiation on all of the trunks.
7/39
Step 2-3: Configure VTP.
Configure switches Dist-1, Acc-1, and Acc-2 with VTP as follows:
1. Switch Dist-1 should be the only VTP server in the domain.
2. The other switches in the domain should be configured as clients.
Use the following values:
- VTP domain: TownEd
- VTP Password: TWE_123!
Note: In order for the VLANs to be distributed from the VTP server to the client switches,
you may need to take action to increment the VTP revision number. This can be done by
adding and deleting a VLAN on the VTP server after the switches in the domain have
complete VTP configurations and trunking is operating correctly.
Copy and Paste script for each router and switch into User EXEC mode
8/39
Ed_Dept Router:
9/39
en
conf ter
ip route 0.0.0.0 0.0.0.0 s0/1/0
ipv6 unicast-routing
ipv6 route ::/0 s0/1/0
router eigrp 99
network 192.168.100.8 0.0.0.3
network 192.168.100.20 0.0.0.3
eigrp router-id 1.1.1.1
exit
ipv6 router eigrp 99
eigrp router-id 1.1.1.1
no shutdown
exit
int s0/0/0
ipv6 eigrp 99
int s0/0/1
ipv6 eigrp 99
exit
int s0/1/0
ipv6 eigrp 99
exit
int s0/0/0
bandwidth 2000
exit
int s0/0/1
bandwidth 2000
exit
router eigrp 99
redistribute static
exit
ipv6 router eigrp 99
redistribute static
Primary-2 Router:
en
conf ter
ip route 0.0.0.0 0.0.0.0 s0/0/0
int g0/0
standby 1 ip 10.1.0.1
standby version 2
10/39
Primary-1 Router
en
conf ter
router eigrp 99
network 10.1.0.0 0.0.0.255
network 192.168.100.8 0.0.0.3
network 192.168.100.32 0.0.0.3
eigrp router-id 2.2.2.2
exit
ipv6 unicast-routing
ipv6 router eigrp 99
eigrp router-id 2.2.2.2
no shutdown
exit
int s0/0/1
ipv6 eigrp 99
int s0/0/0
ipv6 eigrp 99
int g0/0
ipv6 eigrp 99
exit
int s0/0/0
bandwidth 2000
exit
router eigrp 99
passive-interface g0/0
exit
int g0/0
standby 1 ip 10.1.0.1
standby 1 preempt
standby 1 priority 150
standby version 2
High_School Router
11/39
en
conf ter
router eigrp 99
network 10.10.0.0 0.0.0.255
network 10.15.0.0 0.0.0.255
network 10.20.0.0 0.0.0.255
network 192.168.100.20 0.0.0.3
network 192.168.100.32 0.0.0.3
eigrp router-id 3.3.3.3
exit
ipv6 unicast-routing
ipv6 router eigrp 99
eigrp router-id 3.3.3.3
no shutdown
exit
int g0/0.10
ipv6 eigrp 99
int g0/0.15
ipv6 eigrp 99
int g0/0.20
ipv6 eigrp 99
exit
int s0/0/0
ipv6 eigrp 99
int s0/0/1
ipv6 eigrp 99
int s0/1/0
ipv6 eigrp 99
exit
int s0/0/1
bandwidth 2000
exit
router eigrp 99
passive-interface g0/0.10
passive-interface g0/0.15
passive-interface g0/0.20
exit
int g0/0
no sh
Dist-1 Switch
12/39
en
conf ter
int range f0/3-4
channel-group 1 mode active
int range f0/5-6
channel-group 2 mode active
exit
int g0/1
no shutdown
int g0/1
switchport mode trunk
switchport trunk native vlan 99
int g0/1
switchport nonegotiate
Acc-1 Switch:
13/39
en
conf ter
int range f0/3-4
channel-group 1 mode active
int range f0/1-2
channel-group 3 mode active
exit
Acc-2 Switch
14/39
en
conf ter
int range f0/5-6
channel-group 2 mode active
int port-channel 2
switchport mode trunk
switchport trunk native vlan 99
switchport nonegotiate
int range f0/1-2
switchport mode trunk
switchport trunk native vlan 99
int port-channel 3
switchport mode trunk
switchport trunk native vlan 99
switchport nonegotiate
exit
15/39
- Enter telnet 2001:DB8:E::1
- Authenticate your Telnet session with the password cisco.
- Move to privileged EXEC mode using the password admin.
C:\>telnet 2001:DB8:E::1
cisco
en
admin
conf ter
int g0/0
no sh
Additional Default Gateway IP: 10.1.0.1 for PCs PC-A & PC-M
16/39
17/39
18/39
Scaling Networks - Practice Skills Assessment - EIGRP
Connect the PC to the Switch/Router using a Console cable
Copy and Paste script for each router and switch into User EXEC mode
19/39
DataCenter Router:
20/39
en
conf ter
ip route 0.0.0.0 0.0.0.0 s0/1/0
ipv6 unicast-routing
ipv6 route ::/0 s0/1/0
router eigrp 99
network 192.168.100.8 0.0.0.3
network 192.168.100.20 0.0.0.3
eigrp router-id 1.1.1.1
exit
ipv6 router eigrp 99
eigrp router-id 1.1.1.1
no shutdown
exit
int s0/0/0
ipv6 eigrp 99
int s0/0/1
ipv6 eigrp 99
exit
int s0/1/0
ipv6 eigrp 99
exit
int s0/0/0
bandwidth 2000
exit
int s0/0/1
bandwidth 2000
exit
router eigrp 99
redistribute static
exit
ipv6 router eigrp 99
redistribute static
Clinic_10 Router:
en
conf ter
ip route 0.0.0.0 0.0.0.0 s0/0/0
int g0/0
standby 1 ip 10.1.0.1
standby version 2
21/39
Hospital_1 Router:
en
conf ter
router eigrp 99
network 10.1.0.0 0.0.0.255
network 192.168.100.8 0.0.0.3
network 192.168.100.32 0.0.0.3
eigrp router-id 2.2.2.2
exit
ipv6 unicast-routing
ipv6 router eigrp 99
eigrp router-id 2.2.2.2
no shutdown
exit
int s0/0/1
ipv6 eigrp 99
int s0/0/0
ipv6 eigrp 99
int g0/0
ipv6 eigrp 99
exit
int s0/0/0
bandwidth 2000
exit
router eigrp 99
passive-interface g0/0
exit
int g0/0
standby 1 ip 10.1.0.1
standby 1 preempt
standby 1 priority 150
standby version 2
Hospital_2 Router:
22/39
en
conf ter
router eigrp 99
network 10.10.0.0 0.0.0.255
network 10.15.0.0 0.0.0.255
network 10.20.0.0 0.0.0.255
network 192.168.100.20 0.0.0.3
network 192.168.100.32 0.0.0.3
eigrp router-id 3.3.3.3
exit
ipv6 unicast-routing
ipv6 router eigrp 99
eigrp router-id 3.3.3.3
no shutdown
exit
int g0/0.10
ipv6 eigrp 99
int g0/0.15
ipv6 eigrp 99
int g0/0.20
ipv6 eigrp 99
exit
int s0/0/0
ipv6 eigrp 99
int s0/0/1
ipv6 eigrp 99
int s0/1/0
ipv6 eigrp 99
exit
int s0/0/1
bandwidth 2000
exit
router eigrp 99
passive-interface g0/0.10
passive-interface g0/0.15
passive-interface g0/0.20
exit
int g0/0
no sh
Net_1 Switch:
23/39
en
conf ter
int range f0/3-4
channel-group 1 mode active
int range f0/5-6
channel-group 2 mode active
exit
int g0/1
no shutdown
int g0/1
switchport mode trunk
switchport trunk native vlan 99
int g0/1
switchport nonegotiate
FL_1 Switch:
24/39
en
conf ter
int range f0/3-4
channel-group 1 mode active
int range f0/1-2
channel-group 3 mode active
exit
FL_2 Switch:
25/39
en
conf ter
int range f0/5-6
channel-group 2 mode active
int port-channel 2
switchport mode trunk
switchport trunk native vlan 99
switchport nonegotiate
int range f0/1-2
switchport mode trunk
switchport trunk native vlan 99
int port-channel 3
switchport mode trunk
switchport trunk native vlan 99
switchport nonegotiate
exit
26/39
- Enter telnet 2001:DB8:E::1
- Authenticate your Telnet session with the password cisco.
- Move to privileged EXEC mode using the password admin.
C:\>telnet 2001:DB8:E::1
cisco // <~~~ Enter password authenticate Telnet session External>en
admin // <~~~ Enter password to move privileged EXEC mode
External#conf ter
External(config)#int g0/0
External(config-if)#no sh
Additional Default Gateway IP: 10.1.0.1 for PCs Clnc_1 & H1-1
27/39
28/39
TYPE C- Scaling Networks - Practice Skills Assessment - EIGRP
Central Router:
29/39
en
conf ter
ip route 0.0.0.0 0.0.0.0 s0/1/0
ipv6 unicast-routing
ipv6 route ::/0 s0/1/0
router eigrp 99
network 192.168.100.8 0.0.0.3
network 192.168.100.20 0.0.0.3
eigrp router-id 1.1.1.1
exit
ipv6 router eigrp 99
eigrp router-id 1.1.1.1
no shutdown
exit
int s0/0/0
ipv6 eigrp 99
int s0/0/1
ipv6 eigrp 99
exit
int s0/1/0
ipv6 eigrp 99
exit
int s0/0/0
bandwidth 2000
exit
int s0/0/1
bandwidth 2000
exit
router eigrp 99
redistribute static
exit
ipv6 router eigrp 99
redistribute static
East-2 Router:
en
conf ter
ip route 0.0.0.0 0.0.0.0 s0/0/0
int g0/0
standby 1 ip 10.1.0.1
standby version 2
30/39
East Router:
en
conf ter
router eigrp 99
network 10.1.0.0 0.0.0.255
network 192.168.100.8 0.0.0.3
network 192.168.100.32 0.0.0.3
eigrp router-id 2.2.2.2
exit
ipv6 unicast-routing
ipv6 router eigrp 99
eigrp router-id 2.2.2.2
no shutdown
exit
int s0/0/1
ipv6 eigrp 99
int s0/0/0
ipv6 eigrp 99
int g0/0
ipv6 eigrp 99
exit
int s0/0/0
bandwidth 2000
exit
router eigrp 99
passive-interface g0/0
exit
int g0/0
standby 1 ip 10.1.0.1
standby 1 preempt
standby 1 priority 150
standby version 2
West Router:
31/39
en
conf ter
router eigrp 99
network 10.10.0.0 0.0.0.255
network 10.15.0.0 0.0.0.255
network 10.20.0.0 0.0.0.255
network 192.168.100.20 0.0.0.3
network 192.168.100.32 0.0.0.3
eigrp router-id 3.3.3.3
exit
ipv6 unicast-routing
ipv6 router eigrp 99
eigrp router-id 3.3.3.3
no shutdown
exit
int g0/0.10
ipv6 eigrp 99
int g0/0.15
ipv6 eigrp 99
int g0/0.20
ipv6 eigrp 99
exit
int s0/0/0
ipv6 eigrp 99
int s0/0/1
ipv6 eigrp 99
int s0/1/0
ipv6 eigrp 99
exit
int s0/0/1
bandwidth 2000
exit
router eigrp 99
passive-interface g0/0.10
passive-interface g0/0.15
passive-interface g0/0.20
exit
int g0/0
no sh
Net_1 Switch:
32/39
en
conf ter
int range f0/3-4
channel-group 1 mode active
int range f0/5-6
channel-group 2 mode active
exit
int g0/1
no shutdown
int g0/1
switchport mode trunk
switchport trunk native vlan 99
int g0/1
switchport nonegotiate
Bldg-1 Switch:
33/39
en
conf ter
int range f0/3-4
channel-group 1 mode active
int range f0/1-2
channel-group 3 mode active
exit
Bldg-2 Switch:
34/39
en
conf ter
int range f0/5-6
channel-group 2 mode active
int port-channel 2
switchport mode trunk
switchport trunk native vlan 99
switchport nonegotiate
int range f0/1-2
switchport mode trunk
switchport trunk native vlan 99
int port-channel 3
switchport mode trunk
switchport trunk native vlan 99
switchport nonegotiate
exit
35/39
- Enter telnet 2001:DB8:E::1
- Authenticate your Telnet session with the password cisco.
- Move to privileged EXEC mode using the password admin.
C:\>telnet 2001:DB8:E::1
cisco // <~~~ Enter password authenticate Telnet session External>en
admin // <~~~ Enter password to move privileged EXEC mode
External#conf ter
External(config)#int g0/0
External(config-if)#no sh
36/39
37/39
If you only getting 75%, please temporarily uninstall Packet Tracer current version.
Please download and setup “Cisco Packet Tracer 7.0” and Retake Assessment to
getting 100% scores. Goodluck!
Download Full: pka file, PDF file and Answers – 100% Score
38/39
Download
39/39