rarano4 Battery Sizing - Open Electrical
Battery Sizing
From Open Electrical
Contents
Introduction
This article looks at the sizing of batteries for
stationary applications (i.e. they don’t move).
Batteries are used in many applications such as AC
and DC uninterruptible power supply (UPS)
systems, solar power systems, telecommunications,
emergency lighting, etc. Whatever the application,
batteries are seen as a mature, proven technology for
storing electrical energy. In addition to storage,
batteries are also used as a means for providing
voltage support for weak power systems (e.g. at the
end of small, long transmission lines).
Why do the calculation?
Sizing a stationary battery is important to ensure that
the loads being supplied or the power system being
supported are adequately catered for by the battery
for the period of time (i.e. autonomy) for which it is
designed. Improper battery sizing can lead to poor
autonomy times, permanent damage to battery cells from over-discharge, low load voltages, etc.
Figure 1. Stationary batteries on a rack (courtesy of
Power Battery)
When to do the calculation?
The calculation can typically be started when the following information is known:
= Battery loads that need to be supported
= Nominal battery voltage
= Autonomy time(s)
IEEE Definitions
IEEE Sid. 485-1997 provides some definitions related to the battery sizing terminology:
battery duty cycle: The loads a battery is expected to supply for specified time periods.
cell size: The rated capacity of a lead-acid cell or the number of positive plates in a cell.
itpshwwn.cpenelecrical orgwikifindex php ?ite=Battery. Sizing v0a Fale higher than the normal tloat voltage, to correct any
inequalities of voltage and specific gravity that may have developed between the cells during service.
full float operation: Operation of a de system with the battery, battery charger, and load all connected
in parallel and with the battery charger supplying the normal de load plus any charging current required
by the battery. (The battery will deliver current only when the load exceeds the charger output)
period: An interval of time in the battery duty cycle during which the load is assumed to be constant for
Purposes of cell sizing calculations.
rated capacity (lead-acid): The capacity assigned to a cell by its manufacturer for a given discharge
Tate, at a specified electrolyte temperature and specific gravity, to a given end-of-discharge voltage.
valve-regulated lead-acid (VRLA) cell: A lead-acid cell that is sealed with the exception of a valve that
opens to the atmosphere when the internal gas pressure in the cell exceeds atmospheric pressure by a
preselected amount. VRLA cells provide a means for recombination of internally generated oxygen and
the suppression of hydrogen gas evolution to limit water consumption.
vented battery: A battery in which the products of electrolysis and evaporation are allowed to escape
freely to the atmosphere. These batteries are commonly referred to as “flooded.”
Battery Characteristics and Types
Battery Components
Battery technology has not changed much in the last 100 years. The standard construction method
involves flooding lead plates in sulfuric acid. The chemical reaction between the positively charged lead
plate and the negatively charged acid allows the battery to store and “give” electricity. The thickness of
the lead plate is closely related to the lifespan of the battery because of a factor called “Positive Grid
Corrosion”. The positive lead plate gradually wears away over time. Thicker plates are used in deep
cycle batteries. This usually translates to a longer battery life. Although plate thickness is not the only
factor related to longer lifespan, it is the most critical variable.
Battery Lifespan
Most of the loss incurred in charging and discharging batteries is due to internal resistance, which is
eventually wasted as heat. Efficiency ratios are relatively high considering that most lead acid batteries
are 85 to 95 percent efficient at storing the energy they receive. Deep cycle batteries used in renewable
energy applications are designed to provide many years of reliable performance with proper care and
maintenance. Proper maintenance and usage play a major role in battery lifespan. Toiling over your
battery bank daily with complex gadgets and a gallon of distilled water, however, is not necessary. The
most common causes of premature battery failure include loss of electrolyte due to heat or overcharging,
undercharging, excessive vibration, freezing or extremely high temperatures, and using tap water among
other factors
Battery Charging Stages
There are three basic stages in charging a battery: bulk, absorption, and float. These terms signify
different voltage and current variables involved in each stage of charging,
= Bulk Charge; In the first stage of the process, current is sent to the batteries at the maximum safe
_ntpuhwww:cpenciecticacrpwikiindex phpie=Batery_ Sizing 210rate, batteries will accept it until voltage is brought up to nearly 80-90 percent full charge level
There are limits on the amount of current the battery and/or wiring can take.
= Absorption Charge: In the second stage, voltage peaks and stabilizes and current begins to taper
off as internal resistance rises. The charge controller puts out maximum voltage at this stage,
Float Charge: This can also be referred to as trickle charging or a maintenance charge. In this
stage, voltage is reduced to lower levels in order to reduce gassing and prolong battery life. The
main purpose of this stage is basically to maintain the battery's charge in a controlled manner. In
Pulse Width Modulation (PWM) the charger sends small, short charging cycles or “pulses” when
it senses small drops in voltage.
Depth of Discharge DOD)
The Depth of Discharge (DOD) is used to describe how deeply the battery is discharged. If the battery is
100% fully charged, it means the DOD of this battery is 0%. If the battery has delivered 30% of its
energy, here are 70% energy reserved, the DOD of this battery is 30%. And if a battery is 100% empty,
the DOD of this battery is 100%. DOD always can be treated as how much energy that the battery
delivered.
Determining battery state of charge
There are a few ways to determine the state of charge on a battery, each with their own level of
accuracy. As there is no direct method to measure a battery’s state of charge, there are numerous ways to
g0 about it. One way to gauge a battery is by measuring its static voltage and comparing it to a
standardized chart. This is the least accurate method, but it only involves an inexpensive digital meter.
Another method of gauging the battery involves measuring the density or specific gravity of the sulfuric
acid electrolyte. This is the most accurate test, yet it is only applicable to the flooded types. This method
involves measuring the cell's electrolyte density with a battery hydrometer. Electrolyte density is lower
when the battery is discharged and higher as the cells are charged. The battery’s chemical reactions
affect the density of the electrolyte at a constant rate that is predictable enough to get a good indication
of the cell’s state of charge. Using an amp-hour meter one can also obtain an accurate indication of the
battery’s state of charge. Amp-hour meters keep track of all power moving in and out of the battery by
time, and the state of charge is determined by comparing flow rates.
Amp-Hour rating & Capacity
All deep cycle batteries are classified and rated in amp-hours. Amp-hours is the term used to describe a
standardized rate of discharge measuring current relative to time. It is calculated by multiplying amps
and hours. The generally accepted rating time period for most manufacturers is 20 hours. This means
that the battery will provide the rated amperage for about 20 hours until it is down to 10.5 volts or
completely dead. Some battery manufacturers will use 100 hours as the standard fo make them look
better, yet it can be useful in long-term backup calculations.
Renewable Applications
There are three main types of batteries that are commonly used in renewable energy systems, each with
their own advantages and disadvantages. Flooded or “wet” batteries are the most cost efficient and the
most widely used batteries in photovoltaic applications. They require regular maintenance and need to
be used in a vented location, and are extremely well suited for renewable energy applications. Sealed
batteries come in two varieties, the gel cell and Absorbed Glass Mat (AGM) type. The gel cell uses a
hich cpenelecrcalcrgwikiiediex php rate=Batery Slzing anoroto Batery Sizing - Open Bcc
silica additive in its electrolyte solution that causes it to stiffen or gel, eliminating some of the issues
with venting and spillage. The Absorbed Glass Mat construction method suspends the electrolyte in
close proximity with the plate’s active material. These batteries are sealed, requiring virtually no
maintenance. They are more suitable for remote applications where regular maintenance is difficult, or
enclosed locations where venting is an issue.
= a) Flooded Lead Acid (FLA)
Flooded lead acid batteries are the most commonly used batteries, and have the longest track record in
solar electric systems. They usually have the longest life and the lowest cost per amp-hour of any of the
other choices. The downside is that they do require regular maintenance in the form of watering,
equalizing charges and keeping the terminals clean. These cells are often referred to as “wet” cells, and
they come in two varieties: the serviceable, and the maintenance-free type (which means they are
designed to die as soon as the warranty runs out), The serviceable wet cells come with removable caps,
and are the smarter choice, as they allow you to check their status with a hydrometer.
= b) Gelled Electrolyte Sealed Lead Acid (GEL)
Gel sealed batteries use silica to stiffen or “gel” the electrolyte solution, greatly reducing the gasses, and
volatility of the cell. Since all matter expands and contracts with heat, batteries are not truly sealed, but
are "valve regulated”. This means that a tiny valve maintains slight positive pressure. AGM batteries are
slowly phasing out gel technology, but there still are many applications for the gel cells. The recharge
voltage for charging Gel cells are usually lower than the other styles of lead acid batteries, and should be
charged at a slower rate. When they are charged too fast, gas pockets will form on the plates and force
the gelled electrolyte away from the plate, decreasing the capacity until the gas finds its way to the top of
the battery and recombines with the electrolyte.
= c) Sealed Absorbed Glass Mat (AGM)
Absorbed Glass Mat (AGM) is a class of valve-regulated lead acid battery (VLRA) in which the
electrolyte is held in glass mats as opposed to freely flooding the plates. This is achieved by weaving
very thin glass fibers into a mat to increase surface area enough to hold sufficient electrolyte for the
lifetime of the cell. The advantages to using the AGM batteries are many, yet these batteries are
typically twice the cost of their flooded-cell counterpart. On the plus side, these cells can hold roughly
15 times the amp hour capacity of a similar size flooded battery due to their higher power density.
‘Another factor that improves their efficiency is the higher lead purity used in AGM cells. Because of
their sandwich construction, each plate no longer has to support its own weight. Their low internal
resistance allows them to be charged and discharged much faster than other types. AGM cells function
well in colder temperatures and are highly resistant to vibration, There are many advantages to using the
AGM cells over their flooded counterpart that are beyond the scope of this article.
Maintenance & Monitoring
Proper maintenance and monitoring will greatly extend the life of your batteries. Flooded batteries need
to be checked regularly to make sure electrolyte levels are full. The chemical reaction releases gases, as
water molecules are split into hydrogen and oxygen. This, in turn, consumes water and creates the need
to replace it regularly. Only distilled water should ever be used in batteries, and you should never add
any kind of acid solution. The connections from battery to battery and to the charging and load circuits
should always be kept clean and free of corrosion. Corrosion is created upon charging, when a slight
acid mist forms as the electrolyte bubbles. Corrosion buildup will create a good deal of electrical
resistance, eventually contributing to a shortened battery life and malfunctions. A good way to keep up
on the terminals is to regularly clean them with a baking soda solution
tpl openclectrical orgwikindex phpite=Batery. Sizing anosaranoa Battery Sizing - Open Electrical
Future Trends
Companies world-wide are quickly adjusting to the increased global market for solar systems by
developing batteries that are better suited for photovoltaic systems. At some distant point in the future, it
is likely that lead-acid batteries will become extinct, as newer technologies in lithium ion and Nickel
metal hydride continue to evolve. Because lead-acid batteries are under the hood of virtually every car,
advancements in lead-acid technology, however are still being made. New developments in lead-acid
technology usually originate in the auto industry. Efficiency ratings are constantly going up, as new
sensors and improved materials are helping batteries achieve longer lifespan.
Calculation Methodology
The calculation is based on a mixture of normal industry practice and technical standards IEEE Std 485
(1997, R2003) (http://ieeexplore.ieee.org/xpl/mostRecentlssue,jsp?punumber=4899) "Recommended
Practice for Sizing Lead-Acid Batteries for Stationary Applications" and IEEE Std 1115 (2000, R2005)
(http://ieeexplore.icee.org/xpl/mostRecentlssue.jsp?punumber=6976) "Recommended Practice for
Sizing Nickel-Cadmium Batteries for Stationary Applications". The calculation is based on the ampere
hour method for sizing battery capacity (rather than sizing by positive plates).
The focus of this calculation is on standard lead-acid or nickel-cadmium (NiCd) batteries, so please
consult specific supplier information for other types of batteries (e.g. lithium-ion, nickel-metal hydride,
etc). Note also that the design of the battery charger is beyond the scope of this calculation.
There are five main steps in this calculation:
1) Collect the loads that the battery needs to support
2) Construct a load profile and caiculate the design energy (VAh)
3) Select the battery type and determine the characteristics of the cell
4) Select the number of battery cells to be connected in series
5) Calculate the required Ampere-hour (Ah) capacity of the battery
Step 1: Collect the battery loads
‘The first step is to determine the loads that the battery will be supporting. This is largely specific to the
application of the battery, for example an AC UPS System or a Solar Power System.
Step 2: Construct the Load Profile
Refer to the Load Profile Calculation for details on how to construct a load profile and calculate the
design energy, Eq, in VAb.
The autonomy time is often specified by the Client (i.e. in their standards). Alternatively, IEEE 446,
"IEEE Recommended Practice for Emergency and Standby Power Systems for Industrial and
Commercial Applications" has some guidance (particularly Table 3-2) for autonomy times. Note that
IEEE 485 and IEEE 1115 refer to the load profile as the "duty cycle".
Step 3: Select Battery Type
The next step is to select the battery type (e.g. sealed lead-acid, nickel-cadmium, etc). The selection
process is not covered in detail here, but the following factors should be taken into account (as suggested
by IEEE):
Iitpuhwaw cpandlectrcal orgwikitndes php ile=Batlery_ Sizing sroarora Bator Sizng- Open Electrical
Physical characteristics, e.g. dimensions, weight, container material, intercell connections,
terminals
application design life and expected life of cell
Frequency and depth of discharge
Ambient temperature
Charging characteristics
Maintenance requirements
Ventilation requirements
Cell orientation requirements (sealed lead-acid and NiCd)
Seismic factors (shock and vibration)
Next, find the characteristics of the battery cells, typically from supplier data sheets. The characteristics
that should be collected include:
= Battery cell capacities (Ah)
= Cell temperature
= Electrolyte density at full charge (for lead-acid batteries)
= Cell float voltage
= Cell end-of-discharge voltage (EODV).
Battery manufacturers will often quote battery Ah capacities based on a number of different EODVs. For
lead-acid batteries, the selection of an EODV is largely based on an EODV that prevents damage of the
cell through over-discharge (from over-expansion of the cell plates). Typically, 1.75V to 1.8V per cell is
used when discharging over longer than 1 hour. For short discharge durations (i.e. <15 minutes), lower
EODVs of around 1.67V per cell may be used without damaging the cell.
Nickel-Cadmium (NiCd) don't suffer from damaged cells due to over-discharge. Typical EODVs for Ni-
Cd batteries are 1.0V to 1.14V per cell.
Step 4: Number of Cells in Series
The most common number of cells for a specific voltage rating is shown below:
Rated
Voltage Lead-Acid
Ni-Cd
48V 36-40
1sv_ | 60 92-100
2sov | 120 184-200
However, the number of cells in a battery can also be calculated to more accurately match the tolerances
of the load. The number of battery cells required to be connected in series must fall between the two
following limits:
‘ac(1 + Vimaz)
Ve
@ Niias
titaihvwn.opendecioa argwikiindphptitorBatery Sizing 0rarian0%4 ‘Batery Sizing- Open Esetical
@ Nmnin =
where Nj,q2 is the maximum number of battery cells
Nyain is the minimum number of battery cells
Vac is the nominal battery voltage (Vdc)
Vimaz is the maximum load voltage tolerance (%)
Vimin is the minimum load voltage tolerance (%)
, is the cell charging voltage (Vde)
Vooq is the cell end of discharge voltage (Vdc)
The limits are based on the minimum and maximum voltage tolerances of the load. As a maximum, the
battery at float voltage (or boost voltage if applicable) needs to be within the maximum voltage range of
the load. Likewise as a minimum, the battery at its end of discharge voltage must be within the minimum
voltage range of the load. The cell charging voltage depends on the type of charge cycle that is being
used, e.g, float, boost, equalising, etc, and the maximum value should be chosen.
Select the number of cells in between these two limits (more or less arbitrary, though somewhere in the
middle of the min/max values would be most appropriate).
Step 5: Determine Battery Capacity
‘The minimum battery capacity required to accommodate the design load over the specified autonomy
time can be calculated as follows:
Elka X ke he)
Onin = es
‘de a
where C',,;, is the minimum battery capacity (Ah)
Eyq is the design energy over the autonomy time (VAh)
Vie is the nominal battery voltage (Vde)
Kg is a battery ageing factor (%)
key is a temperature correction factor (%)
kr. is a capacity rating factor (%)
Iedog is the maximum depth of discharge (%)
Select a battery Ah capacity that exceeds the minimum capacity calculated above. The battery discharge
rate (C rating) should also be specified, approximately the duration of discharge (e.g. for 8 hours of
discharge, use the C8 rate). The selected battery specification is therefore the Ah capacity and the
discharge rate (e.g. 500Ah C10).
An explanation of the different factors:
= Ageing factor captures the decrease in battery performance due to age.
‘The performance of a lead-acid battery is relatively stable but drops markedly at latter
stages of life. The "knee point" of its life vs performance curve is approximately when the
battery can deliver 80% of its rated capacity. After this point, the battery has reached the
end of its useful life and should be replaced. Therefore, to cnsure that battery can meet
pitwww.opendectical orguikindex prodtive=Batery Sizing mosonora
Battery Sizing - Open Electrical
capacity throughout its
useful life, an ageing
factor of 1.25 should be
applied (i.e. 1/0.8).
There are some
exceptions, check with
the manufacturer.
For Ni-Cd batteries, the
principles are similar to
lead-acid cells. Please
consult the battery
‘manufacturer for
suitable ageing factors,
but generally, applying a
factor of 1.25 is
standard. For
applications with high
temperatures and/or
frequent deep
discharges, a higher
factor of 1.43 may be
[NOTE ube toed ved end ci oes 1215 specie yer ty be wed for
used. For more elt nag oa fl yee nay Forces fear Seg eee be Sear
Salons Sei Be Table 1. Temperature correction factors for vented lead-acid cells
(from IEEE 485)
be used.
Temperature
correction factor is an allowance to capture the ambient installation temperature. The
capacity for battery cells are typicall quoted for a standard operating temperature of 25C and
where this differs with the installation temperature, a correction factor must be applied.
IEEE 485 gives guidance for vented lead-acid cells (see figure right), however for sealed
lead-acid and Ni-Cd cells, please consult manufacturer recommendations. Note that high
temperatures lower battery life irrespective of capacity and the correction factor is for
capacity sizing only, i.e. you CANNOT increase battery life by increasing capacity.
Capacity rating factor accounts for voltage depressions during battery discharge. Lead-
acid batteries experience a voltage dip during the early stages of discharge followed by
some recovery. Ni-Cds may have lower voltages on discharge due to prolonged float
charging (constant voltage). Both of these effects should be accounted for by the capacity
rating factor - please see the manufacturer's recommendations. For Ni-Cd cells, IEEE 1115
Annex C suggests that for float charging applications, K, = rated capacity in Ah / discharge
current in Amps (for specified discharge time and EODV).
Worked Example
Step 1 and 2: Collect Battery Loads and Construct Load Profile
The loads and load profile from the simple example in the Energy Load Profile Calculation will be used
(ee the figure right). The design energy demand calculated for this system is Ey = 3,242.8 VAh.
Step 3: Select Battery Type
tout. openeloctrical orgwikifndex phpe-Batery Sizing anot2ii2r2014 Baltery Sizing Open Electiical
Vented lead acid batteries have been —
selected for this example. 700
Step 4: Number of Cells in
Series 500 |
Suppose that the nominal battery
voltage is Ve = 120Vde, the cell
Load (VA)
charging voltage is V, = 2.25Vde/cell,
the end-of-discharge voltage is Vegg~
1.8Vde/cell, and the minimum and 100 5
maximum load voltage tolerances are
Vignin = 10% and Vmax = 20% |
012345 67 8 9 1011121314
respectively. ‘Time (hours)
|
The maximum number of cells in series Figure 2. Load profile for this example
is:
_ Vie(1 + Visas)
Ve
120 x (1+ 0.!
pas themereeereenert all lls
= 22 = 64 cells
The minimum number of cells in series is:
Vae(1 = Vimin)
‘cod
_ 120x (1
ae 1.8
Nin
60 cells
The selected number of cells in series is 62 cells.
Step 5: Determine Battery Capacity
Given a depth of discharge kjoq = 80%, battery ageing factor k, = 25%, temperature correction factor for
vented cells at 30 deg C of k, = 0.956 and a capacity rating factor of k, = 10%, the minimum battery
capacity is:
Eq x kg X he X he
Opal Te oe as
3,242.8 x 1.25 x 1.1 x 0.956
a a 4d al
120 x 0.8 can
Computer Software
itpitww comelerica.orgwikifindex.ohottile=Battery Sizing a0araz014 ‘ater Sizing - Open Sectical
Some battery manufacturers (such as Alcad (http://www alcad.com/) ) also provide software programs to
size batteries using basic input data such as load profiles, autonomies, etc. The software will size the
batteries and will often also provide details regarding different battery rack (or enclosure) dimensions.
Android App
If you have an android phone then we suggest using our app "Battery Sizing Tool
(hitps://play.google.conv/store/apps/details?id=com_altersource.batterysizing&hl-en|) ".
What Next?
Using the results of the battery sizing calculation, the approximate dimensions of the batteries can be
estimated based on typical vendor information. This will assist in determining the size, number and
dimensions of the battery racks or cabinets required, which can then be used as input into the equipment
/ room layouts. Preliminary budget pricing can also be estimated based on the calculation results.
Retrieved from "http://vww.openelectrical.org/wiki/index.php?title—Battery_Sizing"
Category: Calculations
= This page was last modified on 16 February 2014, at 17:29.
hiipulvwu.openelectrcal.orqwikiindex phpMite=Batery Sizing roo