Professional Documents
Culture Documents
Sci, Best Practice in Steel Construction - Industrial Buildings - Guidance For Architects, Designers & Constractors PDF
Sci, Best Practice in Steel Construction - Industrial Buildings - Guidance For Architects, Designers & Constractors PDF
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement Discuss me ...
EP37 Best Practice in Steel Construction - Industrial Buildings
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss me ...
Best Practice in Steel Construction - INDUSTRIAL
Industrial Buildings
Contents
The Steel Construction Institute (SCI) develops and promotes
the effective use of steel in construction. It is an independent, 01 Introduction
1
membership based organisation. SCI’s research and development
activities cover multi-storey structures, industrial buildings, bridges, civil engineering
and offshore engineering. Activities encompass design guidance on structural steel,
light steel and stainless steels, dynamic performance, fire engineering, sustainable
construction, architectural design, building physics (acoustic and thermal performance),
value engineering, and information technology.
02 Key Design Factors
2
www.steel-sci.org
This publication presents best practice for the design of steel construction
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Although care has been taken to ensure, to the best of our knowledge, that all data 33
and information contained herein are accurate to the extent that they relate to either
matters of fact or accepted practice or matters of opinion at the time of publication,
the partners in the Euro-Build project and the reviewers assume no responsibility for
any errors in or misinterpretations of such data and/or information or any loss or
06 Case Studies
damage arising from or related to their use.
ISBN 978-1-85942-063-8
47
© 2008. The Steel Construction Institute.
This project was carried out with financial support from the European Commission’s
Created on 30 March 2011
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
01 Introduction
Large enclosures or industrial type buildings are very common in business
parks, leisure and sports buildings. Their functionality and architectural
quality are influenced by many factors, e.g. the development plan, the
variety of usages and the desired quality of the building. Steel offers
numerous possibilities to achieve both pleasant and flexible functional use.
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
appearance when viewed from the inside. individual directional load paths. In addition to the primary steel structure,
Figures 2.2 (c) and (d) show lattice trusses Spatial structures and space trusses are a wide range of secondary components
and cable suspended beams, which may non-directional structures; they can be has also been developed, such as
be beneficial to achieve larger spans, as expanded, but would become heavy for cold formed steel purlins, which also
well as desirable for visual reasons. long spans. Figure 2.4 shows some provide for the stability of the framework
examples of spatial structures. (see Figures 2.6 and 2.7).
Arch structures offer advantageous load-
carrying behaviour as well as having a Portal frames These simple types of structural systems
pleasant visual appearance. In Figure 2.3 Steel portal frames are widely used can also be designed to be architecturally
(a), a building with a three-hinged arch is in most of the European countries more appealing by using curved
shown. Alternatively, the structure can be because they combine structural members, cellular or perforated beams
elevated on columns or integrated in a efficiency with functional application. etc., as illustrated in Figure 2.8.
truss structure, as in Figure 2.3 (d). Various configurations of portal frames
can be designed using the same Innovative structural systems have also
Created on 30 March 2011
The forms of buildings with primary and structural concept as shown in Figure 2.5. been developed in which portal frames
secondary structural elements described Multi-bay frames can also be designed, are created by moment resisting
above are all directional structures, for as in Figure 2.5 (e) and (f), either using connections using articulations and ties,
which the loads are carried primarily on single or pairs of internal columns. as given in Figure 2.9.
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
6˚
6m 6m
25 - 40 m 25 - 30 m
(a) Portal frame - medium span (b) Curved portal frame
6˚
8m 8m
3.5 m
8m 9m 8m 25 m
(c) Portal frame with mezzanine floor (d) Portal frame with overhead crane
6˚
6m
25 m
(e) Two bay portal frame
6˚ 6˚
8m
3.5 m
10 m
(f ) Portal frame with integral office
3˚
10˚
Created on 30 March 2011
6m
40 m
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss me ...
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement Key Design Factors 02
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
The installation process of the primary However, columns can also be internal forces are accounted for in the
structure and secondary members, such constructed in a similar way, as illustrated design of the lattice members, when the
as purlins, is generally carried out using in Figure 2.13, in order to provide lattice truss acts to stabilise the building
mobile cranes, as illustrated in Figure 2.10. in‑plane stability. against lateral loads.
illustrated in Figure 2.11. The two generic A pinned structure is an idealisation used or compression permits the design of
forms are W or N bracing arrangements. in design. Moment-resisting connections lightweight structures. However, structures
In this case, stability is generally provided can be designed using bolted or welded that save on materials use do not
by bracing rather than rigid frame action. connections. The resulting additional necessarily lead to economic solutions.
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
8m 8m 8m
25 m 25 m 25 m
(a) Lattice girder - W form (b) Lattice girder - N form (c) Duo-pitch lattice girder
2.5 m 2.5 m
1.5 m 1.0 m 1.0 m
8m 8m 8m
25 m 25 m 20 m
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
(d) Articulated lattice girder (e) Curved lattice girder (f ) Curved lattice truss and canopy
1.0 m 6˚
2.5 m
6m 6m
20 m 20 m
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Particularly in space structures, the joints the following fire safety issues should performing fire tests, three levels of fire
may be very complex and more time be addressed: design calculations:
consuming to construct and install. • Means of escape (number of Level 1: Classification of structural
Therefore, possible applications of this emergency exits, characteristics of components by using tables.
type of structure are industrial buildings exit signs, number of staircases, Level 2: Simplified calculation methods.
that also serve architectural purposes width of doors). Level 3: Advanced calculation methods.
rather than merely functional buildings. • Fire spread (including fire resistance
and reaction to fire). Building physics
Suspended structures can be designed • Smoke and heat exhaust Thermal insulation
by extending columns outside the building ventilation system. The main purpose of thermal insulation
envelope, as illustrated in Figure 2.14. • Active fire fighting measures (hand in industrial buildings is to ensure an
Suspended structures accomplish longer extinguishers, smoke detectors, adequate indoor climate depending
spans, although the suspension cables or sprinklers, plant fire brigade). on the use of the building. During the
rods also penetrate the building envelope, • Access for the fire brigade. heating season, one of the main
and can be obstructive to the use of the functions of the building envelope is
external space. Fire resistance requirements should be to reduce the heat loss by means of
based on the parameters influencing fire effective insulation. This is particularly
Lattice and suspended structures are growth and development, which include: true for buildings with normal indoor
complex and are not covered in detail in • Risk of fire (probability of fire temperatures, such as retail stores,
this Best Practice Guide. occurrence, fire spread, fire duration, exhibition halls and leisure centres,
fire load, severity of fire, etc.). it is true to a lesser extent for
Fire Safety • Ventilation conditions buildings with low indoor temperatures,
Even though the general context of fire (air input, smoke exhaust). such as workshops and warehouses.
safety regulations is the same throughout • Fire compartment
Europe, national differences do exist. (type, size, geometry). For large panels, thermal bridges
For example a single-storey industrial • Type of structural system. and airtightness of joints have a major
building in the Netherlands with a • Evacuation conditions. influence on the energy-balance of
compartment size of 50 x 100 m has no • Safety of rescue team. the building. The thermal insulation
requirements concerning fire resistance, • Risk for neighbouring buildings. has to be placed without gaps and
Created on 30 March 2011
whereas in France, a fire resistance of • Active fire fighting measures. the building envelope must be sealed
30 minutes is required in many cases, and made airtight at longitudinal and
and in Italy the requirement is possibly as The new generation of European transverse joints.
high as 90 minutes. At the design stage, regulations allow, in addition to
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
In the summer, the role of the building for industrial buildings, it may be are given in Eurocodes EN 1991‑1‑1,
envelope is to reduce the effects of solar necessary to limit values of acoustic 1991‑1‑3 and 1991‑1‑4. Table 2.1 shows
gain on the interior space. The summer emissions from particular machinery. the relevant actions and structural
heat reduction depends on the total area components and Figure 2.15 shows a
and orientation of openings, as well as the In steel framed buildings, acoustic insula- typical load scheme.
effectiveness of solar protection measures. tion is mainly achieved by the construction
of the building envelope. All measures of Vertical loads
Condensation�����
risk acoustic insulation are based on the Self weight
Thermal and moisture protection are following physical principles: Where possible, unit weights of materials
linked closely, because damage arising • Interruption of transmission, e.g. should be checked with manufacturers’
from high local humidity is often the result by using multi-skin constructions. data. The figures given in Table 2.2 may
of missing or improperly installed thermal • Sound absorption, e.g. by using be taken as typical of roofing materials
insulation. On the other hand, lack of perforated sheeting or cassettes. used in the pre-design of a portal frame
moisture protection can lead to • Reducing response by increasing the construction. The self weight of the steel
condensation in the construction, mass of a component. frame is typically 0.2 to 0.4 kN/m2,
which in turn affects the effectiveness expressed over the plan area.
of the thermal insulation. For single sound sources, a local
enclosure or isolation is recommended. Service loads
In multi-skin roof or wall constructions, In order to reach a high level of acoustic Loading due to services will vary greatly,
condensation risk has to be controlled insulation, special sound-absorbing roof depending on the use of the building. In a
by installing a vapour barrier on the inner and wall cladding are effective. For multi- portal frame structure, heavy point loads
skin of the structure. Wall constructions skin panels the level of sound insulation may occur from such items as suspended
that are vapour proof on both sides, can be controlled by varying the acoustic walkways, runway and lifting beams or air
like sandwich panels, prevent diffusion. operating mass. Due to the complexity of handling units. The following loads may
However, the humidity in the internal this issue, it is recommended to consult be used for pre-design:
space also has to be regulated by air the specialist manufacturers. • A nominal load over the whole of
conditioning. Section 4 covers roof and the roof area of between 0.1 and
floor systems. Loading 0.25 kN/m² on plan depending on the
The actions and combinations of actions use of the building, and whether or
Created on 30 March 2011
Acoustic insulation described in this section should be not a sprinkler system is provided.
In all European countries, minimum considered in the design of a single-
requirements exist on the sound storey industrial building using a steel Imposed load on roofs
insulation of buildings. In addition, structure. Imposed, snow and wind loads EN 1991-1-1 and -3 define characteristic
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
wind uplift
snow load
wind wind
pressure suction
Frame span
10 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
values of various types of imposed Wind uplift forces on cladding can In the first instance, it is necessary to
loads on roofs: be relatively high at the corner of the identify the size of the enclosure and to
• A minimum load of 0.6 kN/m² (on plan) building and at the eaves and ridge. develop a structural scheme, which will
for roof slopes less than 30° is applied, In these areas, it may be necessary provide this functional space taking into
where no access other than for cleaning to reduce the spacing of the purlins account all the above considerations.
and maintenance is intended. and side rails. The importance of each of these conside-
• A concentrated load of 0.9 kN - this rations depends on the type of building.
will only affect the sheeting design. Imperfections For example, the requirements concerning
• A uniformly distributed load due to Equivalent horizontal forces have to a distribution centre will be different from
snow over the complete roof area. be considered due to geometrical and those of a manufacturing unit.
The value of the load depends on the structural imperfections. According to
building’s location and height above EN 1993‑1‑1 for frames sensitive to To develop an effective concept design,
sea level. If multi-bay portal frames buckling in a sway mode, the effect of it is necessary to review these conside-
with roof slopes are used, the effect of imperfections should be allowed for in rations based on their importance,
concentrated snow loads in the frame analysis by means of an equivalent depending on the type of building.
valleys has to be coonsidered. imperfection in the form of: Table 2.3 presents a matrix which
• A non-uniform load caused by snow • initial sway deflections; and / or relates the importance of each
drifting across the roof due to wind • individual bow imperfections consideration to particular types of
blowing across the ridge of the of members. industrial buildings. Note that this
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
combination with high axial forces, • Design life. the structure of the building. In this case,
then second order effects have to be • Sustainability considerations. floor systems from commercial buildings
considered in the verification procedure. • End of life and re-use. can be used, often based on composite
EURO-BUILD in Steel 11
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Services integration
Space optimization
Weather tightness
Acoustic isolation
Sustainability
Landscaping
Design life
Type of single-storey
industrial buildings
Industrial manufacturing
facilities
Distribution centres
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Retail superstores
Processing plants
Leisure centres
Exhibition halls
Aircraft or maintenance
hangars
structures, e.g. integrated floor beams. the design, even if there is no internal located on the top floor of the building,
Another possible solution is to attach the office space. In order to prevent fire spread, additional escape routes are required and
office to the main structure. This requires the compartment size is limited to a active fire fighting measures have to be
particular attention to be paid to the stabili- certain value. Therefore fire walls have to considered. Fire-spread has to be
sation of the combined parts of the building. be provided for separation and should prevented from one compartment to
ensure at least 60 and often 90 minutes another, which can be achieved, for
Apart from structural issues, special fire resistance. This is even more vital if example by a composite slab between
attention has to be paid to: hazardous goods are stored in the building. the office and industrial space.
Created on 30 March 2011
Fire protection Because the office is designed for use by Thermal insulation
For large industrial buildings, fire compart- a larger number of people, fire safety As for fire safety, offices also have
mentation may play an important role in demands are stricter. If the offices are higher requirements on thermal insulation.
12 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
office office
office hall
hall hall
(a) inside (b) outside (c) on top floor Figure 2.16 Possible location of an office
attached to an industrial building
In industrial buildings used for storage is required, typically using two layers of ventilation depends on the size and
purposes of non-sensitive goods, thermal synthetic material. orientation of the building. Roof vents
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
insulation may not be required. In offices, are a common option for natural
however, a high level of comfort is Service integration ventilation in buildings without suitably
needed, which makes thermal insulation For industrial buildings, special large openings, however these need to
necessary. Therefore the interfaces requirements for building services are be carefully positioned so as to maximize
between the cold and the warm often defined, which may be necessary their performance. Hybrid ventilation
compartments have to be designed to for the operation of machines and systems are now popular in industrial
provide adequate insulation. manufacturing lines. buildings. They use predominantly
natural ventilation, but with mechanically
Acoustic performance The service integration should be taken driven fans to improve predictability of
Especially in industrial buildings with into account in the early planning stages. performance over a wider range of
noise-intensive production processes, In particular, the position and size of weather conditions.
a strict separation between the production ducts should be coordinated with the
unit and the office areas has to be realised. structure and provisions for natural lighting. Mechanical Heat and Ventilation
This may require special measures for Recovery (MHVR) systems use the heat
acoustic insulation, depending on the The use of structural systems, such as from the exiting warm stale air to heat up
production processes. cellular beams and trusses, can facilitate the fresh cool air as it enters the building.
integration of services and help to The warm air is vented out of the building
Floors achieve a coherent appearance alongside the incoming fresh air, allowing
In most cases, the floors for industrial of the building. heat transfer from the exiting to the
buildings are used for vehicles or incoming air. Although this heat transfer
heavy machinery. They are designed The design of the servicing machinery will never be 100% efficient, the use of
to support heavy loads and have to and rooms can be of major importance MHVR systems can significantly reduce
be ’flat’. Concentrated loads due to in industrial buildings. Centralisation
������������������
of the amount of energy required to warm
vehicles, machines, racking and the building services can offer the the fresh air to a comfortable level.
containers have to be considered, advantage of easy maintenance.
depending on the application. Figure 2.17 shows different possible Further issues which may need
solutions of the positioning of the consideration in services design include:
Most industrial buildings have a concrete service rooms. • The possible affect of elements for
floor with a minimum thickness of solar protection on air exchange.
Created on 30 March 2011
150 mm on top of a layer of sand or Natural ventilation reduces the reliance • Odour extraction.
gravel, which is also at least 150 mm on air conditioning systems, which in turn • Control of humidity.
thick. For large floor areas, a sliding layer means a reduction in the building’s CO2 • Control of airtightness.
between the base layer and the concrete emissions. The effectiveness of natural • Acoustic insulation.
EURO-BUILD in Steel 13
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
02 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Lighting
Requirements for the lighting of industrial
buildings depend on the type of use.
The decision to utilise natural daylight (c) internal servicing rooms (d) servicing rooms in the basement
within a building and the type of day-
lighting selected have important implica-
tions for the overall building design.
14 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
03 Support Structures
This section describes common systems used for main support
structures in industrial buildings. The characteristics of portal frames
as well as column and beam structures are described, together with
information on secondary components and connections.
Portal frame structures A number of types of structure can be Portal frame structures
Portal frame buildings are generally low- classified broadly as portal frames.
rise structures, comprising columns and The information given with regard to
horizontal or sloping rafters, connected
by moment-resisting connections.
spans, roof pitch, etc. is typical of the
forms of construction that are illustrated.
Column and beam
structures
Portal frames with hinged column bases Steel sections used in portal frame
are generally preferred as they lead to structures with spans of 12 m to 30 m
Secondary components
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
smaller foundation sizes in comparison to are usually hot rolled sections and are
fixed bases. Furthermore, fixed columns specified in grades S235, S275 or even and bracing
require more expensive connection S355 steel. Use of high-strength steel is
details and therefore are predominately rarely economic in structures where
used only if high horizontal forces have to serviceability (i.e. deflection) or stability
be resisted. However, pinned columns criteria may control the design. Connections
have the disadvantage of leading to
slightly heavier steel weights due to the Frames designed using plastic
lower stiffness of the frame to both global analysis offer greater economy,
vertical and horizontal forces. although elastic global analysis is
preferred in some countries.
This form of rigid frame structure is stable Where plastic analysis is used,
in its own plane and provides a clear the member proportions must be
span that is unobstructed by bracing. appropriate for the development
Stability is achieved by rigid frame action of plastic bending resistance.
provided by continuity at the connections
and this is usually achieved by use of Types of steel portal frames
haunches at the eaves. Pitched roof portal frame
One of the most common structures for
Out-of-plane stability in most cases has industrial buildings is the single-span
to be provided by additional elements, symmetrical portal frame, as shown in
such as tubular braces and purlins Figure 3.2. The following characteristics
(Figure 3.1). By using profiled sheeting, emerged as the most economical and
the stiffening of the roof can be obtained can therefore be seen as a basis at an
by stressed skin diaphragm action early design stage:
without additional bracing. Shear walls, • Span between 15 m and 50 m
cores and the use of fixed ended (25 to 35 m is the most efficient).
columns can also provide out‑of‑plane • Eaves height between 5 and 10 m
restraint to the portal frames. (5 to 6 m is the most efficient).
Created on 30 March 2011
EURO-BUILD in Steel 15
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
03 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
• Roof pitch between 5° and 10° It can be designed to stabilise the frame. Where the crane is of relatively low
(6° is commonly adopted). Often the internal floor requires additional capacity (up to about 20 tonnes),
• Frame spacing between 5 m and fire protection. brackets can be fixed to the columns
8 m (the greater spacings being to support the crane (see Figure 3.5).
associated with the longer span Portal frame with Use of a tie member between haunches
portal frames). external mezzanine across the building or fixed column bases
• Haunches in the rafters at the eaves Offices may be located externally to the may be necessary to reduce the relative
and if necessary at the apex. portal frame, creating an asymmetric eaves deflection. The outward movement
portal structure, as shown in Figure 3.4. of the frame at crane rail level may be of
Table 3.1 can be used as an aid for The main advantage of this framework is critical importance to the functioning of
pre-design of single span portal frames. that large columns and haunches do not the crane.
The use of haunches at the eaves and obstruct the office space. Generally, this
apex both reduces the required depth of additional structure depends on the portal For heavy cranes, it is appropriate to
rafter and achieves an efficient moment frame for its stability. support the crane rails on additional
connection at these points. Often the columns, which may be tied to the portal
haunch is cut from the same size of Crane portal frame with frame columns by bracing in order to
section as the rafter. column brackets provide stability.
Cranes, if needed, have an important
Portal frame with a influence on the design and the Propped portal frame
mezzanine floor dimensions of portal frames. Where the span of a portal frame is
Created on 30 March 2011
Office accommodation is often provided They create additional vertical loads greater than 30 m, and there is no need
within a portal frame structure using as well as considerable horizontal forces, to provide a clear span, a propped portal
a mezzanine floor (see Figure 3.3), which influence the size of the column frame (see Figure 3.6) can reduce the
which may be partial or full width. section, in particular. rafter size and also the horizontal forces
16 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Apex haunch
Eaves haunch
Column
Mezzanine
Mezzanine
Created on 30 March 2011
EURO-BUILD in Steel 17
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
03 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Column
bracket
Figure 3.5 Portal frame with column
brackets
Possible location
* of out of plane restraint
Prop
Clear internal
height
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
18 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Hangers may be
required on long spans
Tie
Industrial door
Gable
bracing
Created on 30 March 2011
Finished
floor level
Personnel door
Figure 3.11 End gables in a frame structure
EURO-BUILD in Steel 19
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
03 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
H
H
Z-shape
min. 80 mm
C-shape
min. 80 mm
Created on 30 March 2011
20 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
to be taken into account during stiffness acts in both directions, and the Purlins
the installation stage by providing structure is stable after installation Purlins transfer the forces from the
temporary bracings. without additional bracing. roof cladding to the primary structural
elements, i.e. rafters. Furthermore, they
Column & beam structures with Secondary components can act as compression members as part
fixed column bases & bracing of the bracing system and provide limited
When using fixed-ended columns, A typical steel portal frame structure with restraint against lateral torsional buckling
larger foundations are required as a its secondary components is shown in of the rafter. For frame spacings up to
result of the additional bending moment. Figure 3.14. Similar systems are provided 7 m, it can be economic to span the
As the columns have low axial forces, for beam and column splices. profiled sheeting between the rafters
the required size of the foundation without the use of purlins. Larger frame
will be large and possibly uneconomic. The bracing systems shown in Figure 3.1 spacings reduce the number of primary
Large columns for industrial buildings are generally achieved by bracing structural elements and foundations,
with a crane may be designed as (usually circular members) in the plane but require the use of heavier purlins.
lattice structures. of the roof or wall. Purlins and side In industrial buildings, hot-rolled
rails support the roof and wall cladding, I‑sections as well as cold-formed profiles
Compared to portal frames, internal and stabilise the steel framework against with Z-, C‑, U- or custom-made shapes
moments in the beams and lateral lateral buckling. Alternatively, panels are used, as shown in Figure 3.12.
deformations are greater. The providing shear stiffness or steel profiled
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
advantages of this system are its sheeting used in diaphragm action When cold-formed purlins are used,
insensitivity to settlement and, in the can be used to provide sufficient out-of- they are usually located at spacings
case of the fixed supports, the base plane stability. of approximately 1.5 m to 2.5 m.
EURO-BUILD in Steel 21
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
03 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Purlins
Cold rolled Rafter
eaves beam
5
Apex haunch
Side 4
rails 3
1 Eaves haunch
Positions of restraint
2 to inner flange of Column
column and rafter
Dado wall Base plate
FFL
Cold rolled
purlins
Sag bars if
necessary
Cold-rolled
eaves beam
Eaves beam
strut
Plan
bracing
Sag rod
Side wall
Created on 30 March 2011
bracing
22 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
hot-rolled I-section
Eaves haunch
End-plate
hot-rolled I-section
EURO-BUILD in Steel 23
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
03 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Apex haunch
Figure 3.17 (Below) Typical examples (if needed)
of nominally pinned column
bases in a portal frame
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Created on 30 March 2011
24 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
EURO-BUILD in Steel 25
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
04 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
so that they provide the level of restraint boundary. Alternatively, an impermeable that significantly less restraint is provided
to the purlins. Alternative forms of membrane on top of the liner tray may to the purlins than with a conventionally
construction using plastic ferrule and Z- be provided. fixed system. Nevertheless, a correctly
or rail and bracket spacers are shown in fixed liner tray will provide adequate
Figure 4.2 and Figure 4.3. Standing seam sheeting restraint to the purlins.
Standing seam sheeting has concealed
As insulation depths have increased to fixings and can be fixed in lengths of up Composite or sandwich panels
provide greater insulation performance, to 30 m. The advantages are that there Composite or sandwich panels are
there has been a move towards ‘rail are no penetrations directly through the formed by creating a foam insulation
and bracket’ solutions, as they provide sheeting that could lead to water leakage, layer between the outer and inner layer of
greater stability. and fixing is rapid. The fastenings are in sheeting. Composite panels have good
the form of clips that hold the sheeting spanning capabilities due to composite
With adequate sealing of joints, the liner down but allow it to move longitudinally action in bending. Both standing seam
trays may be used to form an airtight (see Figure 4.4). The disadvantage is (see Figure 4.5) and direct fixing systems
Outer sheeting
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Insulation
Z spacer
Liner tray
Sheeting
Rail Insulation
Liner tray
Created on 30 March 2011
Bracket
Figure 4.3 (Bottom right) Double-skin
construction using ‘rail and
bracket’ spacers
26 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
are available. These will clearly without or with few joints. The basic Requirements for corrosion protection of
provide widely different levels of material for the outer layers is usually sandwich or composite panels are the
restraint to the purlins. galvanised coated steel sheeting with same as for trapezoidal steel sheets.
thicknesses of 0.4 to 1.0 mm. For foam insulation, the following
Sandwich elements for roofs generally solutions have been developed:
have a width of 1000 mm with thicknesses The inner layers of sandwich panels are • Polyurethane PUR rigid foam;
between 70 and 110 mm, depending on often lined or slotted; special designs • Mineral fibre insulating material;
the required insulation level and structural are available with plane surfaces. • Polystyrene (only used in exceptions
demands. Despite being relatively Close‑pitch flutings have also been due to its lower insulation behaviour).
thick elements, the self-weights are established, which are fully profiled,
comparatively low. Thus the elements yet appearing as a plane surface from The steel skin and the insulating foam
are easy to handle and assemble. a certain distance. Some patterns for are physiologically harmless during
Component lengths of up to 20 m for external surfaces of sandwich panels production and assembly as well as in
roofs and walls permit constructions are shown in Figure 4.6. the permanent use in the building.
Sheeting
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Insulation
Standing seam clip
Sheeting
Insulation
Standing
seam clip
Created on 30 March 2011
EURO-BUILD in Steel 27
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
04 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Flat
Wide profiled
Narrow profiled
Micro-profiled
Trapezoidal
Corrugated
Figure 4.6 Types of external surfaces for
sandwich panels
Composite or sandwich The core insulation is odourless, free buckling of the panel. The darker
panels offer numerous from rot and mould-resistant. Further- the colour of the panel, the higher are
advantages: more it offers good recycling possibilities. the compression forces. Therefore,
for continuous panels, checks for
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
• Panel manufacturing A key factor to be taken into account for ‘temperature in summer’ and
provides short the design of sandwich panels is the ‘temperature in winter’ design
construction time and temperature difference across the element. situations have to be performed,
The separation of the inner and outer skins taking into account the colour of the
cost-efficiency leads to heating and therefore extension panel. At a European level, EN 14509
of the outer sheet due to solar radiation. (in preparation) defines the structural
• Good building physics design method as well as the production
performance For single span panels, this results in and quality principles of sandwich and
a flexure of the panel. Even though composite panels.
• Can be installed in this does not lead to additional internal
nearly all weather forces, it might influence the appearance Manufacturers should be consulted for
conditions of the envelope. more information.
• Long-span capabilities For continuous panels, restaint of flexure Special roofing systems
which minimise the leads to bending and to compressive A flat roof of an industrial building spans
support structure forces in the skins, which can lead to a large area and is exposed to solar effects.
Created on 30 March 2011
28 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Sandwich Sandwich Profile sheet long. joint transv. joint Type of fastening
Steel Sub- Timber Sub- Steel Sub- sheets/sheet sheets/sheet element
structure structure structure
A A
Z
Stahl-Informations-Zentrum: Dach und Fassadenelemente aus Stahl - Erfolgreich Planen und Konstruieren, Figure 4.8 Range of application for
Dokumentation 588, Düsseldorf, 2005 fastening elements in
various claddings
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Advantage can be taken from this exposure For the fastening of steel sheeting, Wall Systems
by integrating a membrane with photo- (self-tapping) screws or rivets are used. Numerous systems exist for the
conductive cells into the roof to capture For profiled sheeting, at least every design of external walls for industrial
solar energy. There are economic
�������������
and second rib has to be fixed to the supporting buildings. Cladding types made of
easy to process products on the market. structure. If sheets are used as a stressed steel sheeting are most frequently
skin diaphragm, the number of fixings used, because they offer high-quality
Another steel roof cladding system has have to be designed so that they resist standards, short construction time and
been developed with an integrated system the applied shear flow. cost-efficiency. Generally, steel sheet
of water channels in order to collect and wall cladding follows the same generic
use the heat (a solar thermal collector). For sandwich elements, the designer has types as roof cladding, and the main
to consider the influence of the fastening types are:
Fastening elements method on the strength of the panel. • Sheeting, orientated vertically and
Fastening techniques include the supported on side rails;
connections of the sheets to the Figure 4.8 shows the different types of • Sheeting or structural liner trays
supporting structure and the fastening elements depending on the spanning horizontally between
connections between sheets. support structure. primary frame;
Created on 30 March 2011
EURO-BUILD in Steel 29
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
04 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
• Composite or sandwich panels with a thickness of 40 to 120 mm, and in For the completion of the facades,
spanning horizontally between the some cases up to 200 mm for elements special formed components for the
columns, eliminating side rails; used in cold stores. transitions between wall and roof have
• Metallic cassette supported been developed. For high quality facades,
by side rails. To achieve a good appearance of the manufacturers offer angled or rounded
building, the following aspects are important: components for the roof or corner
Different forms of cladding may be used • Texture of the surface. sections. These special components
together for visual effect in the same • Colour. have to be of the same quality and colour
facade. Some examples are illustrated • Detailing of joints. as the adjacent elements.
in Figure 4.9 to Figure 4.11. • Type of fixing.
Fire design of walls
Brickwork is often used as a ‘dado’ In addition, for a modern construction Where buildings are close to a site
wall for impact resistance, as shown system, the client expects practically boundary, national building regulations
in Figure 4.11. invisible fixings and clean transitions at usually require that the wall is designed
the building’s corners. Nevertheless, to prevent spread of fire to adjacent
Sandwich or composite panels through fixings are still commonly used. property. Fire tests have shown that a
Sandwich or composite panels are The details comprise either hidden fixings number of types of panels can perform
double skin continuously produced or elements with additional clip fasteners; adequately, provided that they remain
elements with various types of core as shown in Figure 4.5 and Figure 4.12. fixed to the structure. Further guidance
Created on 30 March 2011
insulation. They are the most common By the use of additional clip fasteners, should be sought from the manufacturers.
choice of wall cladding for industrial slight dents that may occur at the fixings
buildings in Europe. For walls, sandwich due to improper assembly or temperature It is often considered necessary to
elements have widths of 600 to 1200 mm influence can be avoided. provide slotted holes in the side rail
30 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
connections to allow for thermal The use of this architectural high-quality colours for the façade. A variety of
expansion. In order to ensure that this façade does not automatically lead to colours, including pastel shading and
does not compromise the stability of the higher costs. In the example shown in metallic finishes, are available from many
column by removing the restraint under Figure 4.14, hot-rolled sections are used sheeting suppliers. Figure 4.15 shows
normal conditions, the slotted holes are for the structure as well as a standardised an example of a building well integrated
fitted with washers made from a material façade-system. By integrating solar gains with its surroundings by the use of
that will melt at high temperatures and into the thermal balance, running costs coloured facades.
allow the side rail to move relative to are also reduced significantly. The structure
the column under fire conditions only. supporting the façade and the detailing As an additional feature, photovoltaic
An example of this type of detail is can be adapted from solutions for multi- panels may be integrated in the façade.
shown in Figure 4.13. storey buildings, where these kinds of Despite the fact that the angle to the sun
building envelopes are common practice. is not optimal, the use of multi-layer
Other types of façades coatings makes the solar cells less
Many other types of façade materials Another modern way of designing dependent on the angle of incidence of
may be used for industrial buildings, for industrial buildings in an architecturally the sun’s rays. An example of this
example glass, as shown in Figure 4.14. appealing way is of the use of different technology is shown in Figure 4.16.
Slotted
hole for
expansion
Cleat Splice
plate
Created on 30 March 2011
EURO-BUILD in Steel 31
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
04 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
32 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
05 National Practice
In this section, some national practices are given for several countries.
The construction systems have been identified as good practice in the
countries concerned, although they may not be widely used in Europe.
shop and the part of the beam with insulation and fire resistance. Often the
constant height is then connected on site waterproofing layer is fixed to the load-
using a bolted connection. bearing layer by a clamped joint with
EURO-BUILD in Steel 33
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
05 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
water-proofing layer
sliding system
special sliding system, so that the transmission losses through the The easier the calculation method,
waterproofing layer does not need building envelope have to be satisfied. the more conservative is the result.
to be penetrated. The heating installation does not have
to be considered. There are also fewer Using the simplified calculation method 1,
External walls restrictions concerning the thermal single-storey industrial buildings can be
For industrial buildings in Germany, many insulation, which leads to smaller designed in unprotected steel up to a
types of walls are used depending on the thicknesses of insulation. plan area of 1,800 m² without providing
building use, building physics require- any active fire-fighting measures. By use
ments and the fire boundary conditions. Fire safety of automatic sprinkler units, the maximum
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
*Area of heat extraction surfaces ≥ 5% and width of building ≤ 40 m Table 5.1 Allowable size of fire compart-
ments for industrial buildings
34 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
EURO-BUILD in Steel 35
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
05 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
non-steel cellular beams are becoming a popular the Netherlands, except for barns and
10%
sandwich alternative to solid web sections. stables in the agricultural sector.
45%
Roofs
Unlike other European countries, the
vast majority of industrial buildings in the
Netherlands have flat roofs. Pitched roofs
are very rare in single-storey buildings in
36 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Fire protection will be renovated, and it is encouraged to industrial buildings can be identified as:
The main reason for the high market find a parking solution inside the building • Built-up ‘I’ shaped sections for the
share of steel products in industrial envelope to decrease the pressure on primary structure of portal frames
buildings is the requirement for fire public space (Figure 5.8). (tapered columns and rafters from
resistance. In the Netherlands, these 750 mm deep to 1280 mm deep,
requirements are relatively low in Energy usually from steel grade S275JR).
comparison to other European countries. In 2012, all new industrial buildings will • Cold-formed ‘Z’ and ‘C’ shaped
have to be ‘energy neutral’. This means sections for the secondary structural
For single-storey buildings and most that the energy consumption has to be members (roof purlins, side walls, etc.).
industrial buildings with a small office, equal to or less than the energy produced. • Roof and wall cladding systems in
there are no requirements for fire In the town of Zaandam, an experimental compliance with new fire regulations.
resistance from the construction. In some ‘zero-energy shed’ has been built with
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
cases, 30 or 60 minutes is required for promising results, and this technology Generally, tapered rafters have spans of
escape routes, for fire compartments or is potentially useable more widely. 25-50 m but it is possible to design spans
for prevention of fire spread between of 60-70 m without intermediate supports.
spaces and to adjacent buildings. These Current Practice in Spain On the other hand, the typical spacings
requirements are usually easy to meet Structure between portal frames are 9-10 m, and
with simple fire protection measures. Most industrial buildings in Spain are columns are of 7-12 m height.
constructed from built‑up sections,
Parking although hot rolled sections are often The complementary sub‑systems consist
At the moment about 70,000 hectares of used for bespoke shed designs. of mezzanine floors, crane runway beams,
land is in use as an industrial development Construction components include crane beams, roof platforms, canopies,
area. This is approximately 2% of the structural systems, roof and wall cladding parapets, and all accessories needed for
total area of the Netherlands. The Dutch systems. The pre-engineered systems a complete and functional building.
government is trying to stop the rapidly are delivered on site ready to be
increasing area zoned for economic assembled. This complete process is The foundation requirements of these
activities. Increasingly, industrial and quick, efficient and economic. steel buildings are reduced significantly
commercial buildings in these districts The structural elements in many Spanish because of the open spaces provided by
Created on 30 March 2011
EURO-BUILD in Steel 37
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
05 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Code Description
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Spanish Structural Steel Design Code (Instrucción de Acero Estructural). This regulation will be
EAE
compulsory in 2009.
Spanish Technical Building Code (Código Técnico de la Edificación): Basic Documents: Basis of design
CTE
(DB-SE), actions (DB‑SE‑AE) and design of steel structures (DB‑SE‑A).
EN 1993-1-1 Eurocode 3: Design of steel structures. Part 1-1: General rules and regulations for buildings.
Eurocode 3: Design of steel structures. Part 1-3: Supplementary rules for cold formed thin gauge members
EN 1993-1-3
and sheeting.
Spanish Regulation of Fire Security in Industrial Building (RSCIEI - Reglamento de Seguridad Contra
RSCIEI Incendios en los Establecimientos Industriales) The RSCIEI is a compulsory document for the fire safety
design of industrial buildings.
the clear span system, the longer bay • The use of tapered built-up primary Public and private companies,
lengths and the lower weight of the structure. structural members (columns and contractors and designers benefit as a
rafters) results in up to a 40% weight result of the cost savings and from the
Steel industrial buildings use a variety of advantage for the main rigid frames faster construction process.
materials that satisfy a wide range of when compared to the use of
structural requirements. This flexibility conventional hot rolled sections. Regulations
provides an unlimited range of building • The use of ‘Z’ shaped secondary The main regulations affecting the design
configurations and applications. structural members (roof purlins and of industrial buildings in Spain are given
side rails), particularly the overlapping in Table 5.2.
Structural advantages of the ‘Z’ shaped purlins at the frames,
This structural system offers many results in up to a 25% weight saving Fire safety engineering
advantages compared to traditional for the secondary members. The Spanish Fire Safety Regulation for
construction. Advanced design and • Generally, all the components are industrial buildings (RSCIEI) requires an
fabrication methods help to reduce costs factory-produced on automated assessment of the fire resistance of the
through faster construction and production lines, saving many building according to the expected fire
minimised labour on site. problems in installation. loads, compartment size and
Created on 30 March 2011
38 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss me ...
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement National Practice 05
resistance, i.e. detached sheds with low Current practice in Sweden 150 mm of mineral wool. The buildings
fire load, fire safety engineering offers a A typical Swedish industrial building often comprise an office space in parts of
more competitive approach in the case of Open plan buildings, such as industrial the building using an intermediate floor.
high fire loads or layouts requiring larger buildings, are a very important market for
compartment sizes. An example of a steel in Sweden (SBI, 2004). Common The most common and often most
model used to determine structural dimensions for light industrial buildings economic way of stabilising an open
performance and time to collapse of a are spans between 15 and 25 m with a plan building is to insert wind bracing
steel framed industrial building in fire is height of 5 to 8 m. Building plan areas at the ends and in the long sides and
given in Figure 5.12. of 1500-2000 m² are common. Often to utilise the profiled sheeting in the
companies specialising in these systems roof as a stiff stressed skin diaphragm,
Acknowledgements deliver the building as a turnkey product. as shown in Figure 5.13. The columns
Created on 30 March 2011
The images shown have been provided are designed as pinned. The wall
by Prado Transformados Metálicos S.A. Modern buildings of this type are usually sheeting may also be used as a
(www.pradotm.com). insulated with approximately 120 to stressed skin diaphragm.
EURO-BUILD in Steel 39
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
05 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
N
qah/2 qah/2+N
N
h
qah/2 b
a
A typical open plan building is shown in considered as pin-ended at the base, Roof cladding
Figure 5.14. Often a gabled roof with an four bolts are recommended in order to There are a number of products for
angle of 3.6° or 5.7° is used. The spacing provide column stability during erection. roofs, mainly profiled sheeting and tiles.
between rafters is typically 6 to 10 m. The profiled sheeting is typically of the
The walls are made from composite panels For non-insulated industrial buildings, form shown in Figure 5.15. Roof tiles
or profiled sheeting placed on light steel the profiled sheeting is supported by may be used for roof slopes of 14° and
side rails. The insulation is placed on top purlins, and Z‑profiles are often used more. Roofing tiles use traditional colours
of the profiled sheeting and covered with as purlins up to 12 m span. and are significantly lighter than ceramic
a suitable roof material. A plastic membrane or concrete tiles.
is used for air and moisture-tightness. Using pinned columns, it is essential to
stabilise the building during erection. Deep profiled sheeting may be used for
Lattice trusses are generally used for It is often necessary to brace columns insulated roofs with spans up to around
the rafters. Spans up to 45 m can be and sometimes the rafters too. As bracing 11 m and the longer spans are achieved
achieved with standard sections. of the columns is necessary during erection, with sheeting stiffened in both directions.
Created on 30 March 2011
The columns are typically HEA-sections, it is common to design the bracing as Shorter spans, up to 8 m, are achieved
fastened with four anchor bolts on a permanent, thus not considering with more traditional profiles.
base plate. Although the columns are diaphragm action of the walls.
40 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
EURO-BUILD in Steel 41
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
05 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
The roof is usually designed to also act as There are products on the Swedish the high value activities for which these
a stressed skin diaphragm which enables market that can satisfy and exceed the buildings are employed. The introduction
it to be constructed without bracing. Swedish building regulations as to the of a revised Part L, with its more onerous
heat insulation of industrial buildings. requirements, and the European ‘Energy
Profiled sheeting is used as load bearing Typical U-values for a 150 mm composite Performance of Buildings’ Directive in
elements for insulated roofs. The height panel are 0.24-0.28 W/m²K and there are April 2006 have led to the following
of the profile is chosen depending on the standard solutions for U-values down to requirements:
span. Insulation in the form of mineral 0.17 W/m²K. • The need to achieve a saving of
wool is used in two layers with plastic foil around 23 to 28% in CO2 emissions
as a damp proof layer and an air barrier. Current Practice in the UK when measured against the equivalent
General Issues building to 2002 Regulations;
Trapezoidal sheeting is used as the The construction of large single-storey • The introduction of energy passports
external roof material. A minimum roof industrial buildings, widely known as for many types of buildings.
angle of 3.6° is required. ‘sheds’, is a significant part of the UK
steel construction sector. They are used Selection of Steel for Single-storey
U‑values of below 0.3 W/m²K can be as retail stores, distribution warehouses, Industrial Buildings
achieved, dependant on the thickness of manufacturing facilities and leisure centres. The following criteria can affect the
the insulation. This meets the Swedish value that the building brings to the
building regulations. Examples of innovations are the use of clients and users:
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
There are slotted separators for fastening envelope systems, in particular related to
of the profiled sheeting, allowing for the energy conservation demands of The client may at some point wish to sell
mineral wool as insulation. Part L of the UK Building Regulations and the building to an investment
42 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
organisation. To facilitate this option, quality materials with a longer life Value for money
criteria such as minimum height and expectancy and reduced maintenance Steel has achieved a large market share
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
higher imposed loads are often specified costs are encouraged. in this sector because of responsiveness
to maintain the asset value and provide to client demand. With the increasing
flexibility for future uses. Sustainability complexity in design, there is also an
Energy costs and the reduction of CO2 increased inter-dependency between the
Maintenance emissions are becoming increasingly various elements and a high degree of
Many buildings are constructed for important and sustainability is now a cooperation and coordination.
owner occupation. Where a building is key issue within the planning process.
let, ‘full repairing 25 year leases’ In the future, it is likely that planning Design Issues
(where the tenant is responsible for permission will be easier to obtain with Steel construction is one of the most
maintenance), are being replaced by sustainable, environmentally friendly efficient sectors in the construction
shorter leases, where the owner carries solutions. Many clients, potential clients industry. Leading suppliers manufacture
maintenance responsibility. Where the and occupiers have sustainability the components offsite, using computer
original owner has responsibility for policies against which their performance controlled equipment driven directly by
maintenance, the choice of better is monitored. information contained in 3D computer
Created on 30 March 2011
EURO-BUILD in Steel 43
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
05 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
models used for detailing. In addition to Energy performance the interfaces between the various
informing the manufacturing process, Reductions in U‑values over recent years specialist systems. This task is traditionally
the information in the model is also used for have lead to a considerable increase in undertaken by the architect, but better
ordering, scheduling, delivery and erection. insulation thickness, with implications for coordination is achieved if the main
stability (particularly of built-up systems), contractor is responsible for the design.
Choice of primary frame cladding weight and consequential
The most popular choice of structural handling requirements. However, the Design process
form for single-storey buildings with point has now been reached where Attributes that should be considered,
spans of 25 to 60 m is the portal frame further increases in insulation thickness in addition to those required by the
because of its structural efficiency and are unlikely to lead to significant Regulations, include:
ease of fabrication and erection. Portal improvements in energy performance. • Overall geometrical considerations.
frames may be designed using elastic or • Minimum height (clearance for crane
plastic analysis techniques. Elastically For many applications, roof lights are beams, depth of haunch, etc.).
designed portal frames are likely to be important because they reduce the amount • Achieving maximum lettable area
heavier, but are simpler to design and of artificial lighting that is needed and, according to the conventions for
detail using non‑specialist design software. consequently, the energy demands of the measurement.
building. However, they also increase • Column layouts to give appropriate
For longer spans, lattice trusses may be solar gain, which can lead to overheating future flexibility of use.
used as an alternative to portal frames. in summer and increase cooling demand. • Loading and future loading
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
44 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Aspect of Design Current Designs Future Designs (in addition to current practice)
Portal frames of 30‑35 m span with 6° roof slope Steel portal frames with 2° slope
Building form and
structure 6‑8 m bay width with internal columns
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
at 12‑16 m spacing
Fibre reinforced 200 mm concrete ground slab Post‑tensioned concrete ground slab
Adjoining steel framed office of 13.5 m
depth in 6 and 7.5 m spans
EURO-BUILD in Steel 45
Created on 30 March 2011
46
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement Discuss
05 Best me ...
EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
06 Case Studies
A series of Case Studies are presented in this Section to illustrate the
design and construction principles discussed earlier. The Case Studies
cover a range of building forms and locations throughout Europe.
The Case Studies and their structural • Netto Supermarket, Sweden. Cargo Hub,
systems are summarised as follows: Lightweight column and beam
• Cargo Hub, East Midlands Airport, UK. structure using stressed skin action. East Midlands Airport
Two bay portal frame and cellular • Distribution Centre,
beams for mezzanine floor and
adjacent office area.
Waghäusel, Germany.
Rack-supported storage system
Airbus Industrial Hall,
• Airbus Industrial Hall, Toulouse, France. with cassette walls and a ‘green’ roof Toulouse
Long-span lattice trusses using steel sheeting for economical
for flexibility of space and fast- warehouse construction.
Cactus Shopping Centre,
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
track construction.
• Cactus Shopping centre,
Esch/Alzette, Luxembourg.
Esch/Alzette
Portal frames using curved cellular
beams for column free internal space Netto Supermarket,
and maximum transparency.
Sweden
Distribution Centre,
Waghäusel
Created on 30 March 2011
EURO-BUILD in Steel 47
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
06 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Application Benefits:
• Simple portal frame
solution provides
efficient use of space
• Mezzanine floor using
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
48 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Project Team Construction Details The fire engineering strategy was also
Client: Roof and roof trusses key to the whole building concept and the
DHL The two bay portal frame structures floor of the mezzanine was designed with
Architect: were designed plastically to achieve the an open steel grillage in order to allow for
Burkes Green most efficient solution for the 40,000 m2 smoke extraction at high level.
Consultant: warehouse building. Mechanical handling
Burkes Green equipment was supported by an The 2 bay portal frame was designed
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Contractor: independent mezzanine structure with a ‘stiff’ line of columns and was
Howard Associates which used cellular steel beams. constructed before the design of the
Steelwork mechanical handling system had been
Westcol The same technology was used for the completed. The flexible design of the
Services: 9,000 m2 office building, which had to be steel structure made installation of this
Couch Perry Wilkes flexible in its use, as the predicted system easier in dry internal conditions.
lifespan in its current format was only
15 years. Cellular beams were chosen to The open sided canopy was also proble-
provide services integration through the matical, being 22.5 m span and 45 m
600 mm diameter openings. The design wide between supports. The canopy
of the office area was further complicated projected at 45O and was connected to
by the need to span over a service road, the portal frame structure for its stability.
which necessitated supporting the floors The roof of the office comprised curved
from a long span truss of roof level. steel beams of 150 m radius.
Created on 30 March 2011
EURO-BUILD in Steel 49
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
06 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Application Benefits:
• Fast track construction
• Efficient use of
steel components
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
• Flexibility of
space organisation
• Sustainable design
approach
• High crane facilities
This industrial building covers • Two parallel industrial rolling cranes,
200,000 m² of floor space, is 45 m high 35 m span, 30 tonnes capacity for
and provides spans of more than 115 m. fuselage transportation.
Criteria to be met were efficient space • Two dual loads 2 x 4 suspended
occupancy and flexibility in arrangement cranes for normal service.
of the internal space.
The wing‑lifting cranes roll on rails
Due to the expected change in the suspended on the truss of the frame of
industrial process after several years of the roof. Sliding doors provide a
production, a reconfiguration/refurbishing 117 x 32 m² opening. They are supported
approach design was considered, taking by their own structural frame. This huge
count of rapid financial return. structure was designed and installed
Architectural and structural appearance economically using fabricated sections
were intended to be an attractive and a trussed upper beam.
reflection of the company performance.
50 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Contractor: along the building and made of rectan- • Rapid connection operations in a
URSSA (Spain), CIMOLAI (Italy), gular hollow steel sections. Each roof critical erection phase.
CASTEL et FROMAGET, JOSEPH element comprises a pair of front and • No welding operation during assembly.
PARIS, RICHARD DUCROS (France), rear trusses, roof structure, roof service • The truss upper flange element is
BUYCK (Belgium) equipments, fire safety network, etc., and connected and simply sits on a short
Control Office: when completed at ground level is lifted span beam on top of the column.
SOCOTEC and VERITAS and positioned at the top of the columns
in one piece. The vertical deflection of the trusses was
limited to span/2000 due to crane
Columns are rigidly fixed to the ground operation requirements.
and have equal slenderness ratio in each
direction to avoid any horizontal buckling The elements of the main truss spanning
phenomenon during lifting operations. across the building were I shape
fabricated sections and bolted on joints.
Assembly of the trusses at ground level Each column was made of two separate
has the advantage of achieving safe fabricated sections jointed by a
construction, limited use of scaffolding, continuous truss web.
Created on 30 March 2011
EURO-BUILD in Steel 51
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
06 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Application Benefits:
• Column-free internal
space provides
maximum flexibility
• Attractive appearance
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
This medium size supermarket is situated Due to the location of the supermarket in
in the city centre of Esch/Alzette and it a city centre, the local authorities required
replaces an older structure. The owner a fire resistance of 90 minutes for the
wanted to have a modern bright shopping steel structure supporting the roof.
centre and opted for an open space with The Natural Fire Safety Concept was
huge glazed surface for two of the applied to calculate the development of
Created on 30 March 2011
façades. It was a requirement that the the fire in the supermarket. Using this
steel structure, with its long span curved concept, the opportunity for a building
cellular beams, should be visible. with a fully glazed façade and visible
steel structure has been retained.
52 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Contractor: has a single 20 m span. The column the small size of the building. The fire
MABILUX S.A. height is 7.5 m and the maximum height temperature was calculated using the
Fire Engineering: in the middle of the curved beam is 2-zone software Ozone and localised
ArcelorMittal 9.1 m. The distance between adjacent temperatures were calculated using the
main frames is 7.5 m. Hasemi methodology. A set of simulations
was performed to analyse the breaking of
Building Facts Frames are connected by continuous the glazed walls (front and back façades
Construction period: 2003 purlins (IPE200). The roofing is made are completely glazed).
Total height: 9.13 m with a steel decking (HOESCH TR44A),
Ground-plan: 28.5 x 48.0 m insulation and waterproofing. The beams As the maximum resulting steel
are ArcelorMittal Cellular Beams® made temperatures in the columns were
from HEB450 in S235 steel. The height of 880°C, a 3-D finite element analysis
the beam is 590 mm, the diameter of the was performed, taking into account the
openings is 400 mm and the distance whole structure of the building at this
between the openings is 600 mm. temperature. One complete model of the
building in 3 dimensions was analysed.
Natural Fire Safety Concept All the simulations were made using the
ArcelorMittal was asked to perform the FE software SAFIR. The result of this fire
fire engineering of the structure and the engineering approach was the decision
authorities accepted the application of the that the steel structure did not require
Natural Fire Safety Concept. The fire any passive fire protection.
design was based on the prescriptions of
Created on 30 March 2011
EURO-BUILD in Steel 53
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
06 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Application Benefits:
• Rapid building method
• High level of
prefabrication
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
54 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Steel Constructor: bracings, mainly HEA-profiles. HEA- trusses and roof sheeting was about
EAB AB profiles are also used as gable beams. one week, which was done after the
For single span ceiling joists with a casting of the foundation. The next step
maximum span of 10 m, IPE-profiles was to assemble walls and to install the
Building Facts are used. roofing. Finally, the services and the
Shopping area: 750 m² interior work were completed in a
Steel use: 20 tonnes When it is important to keep the building weather-proof building.
Roof sheeting: 1000 m2 height to a minimum, or when it is not
Total erection time: 5 weeks
Total project time: 17 weeks
EURO-BUILD in Steel 55
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss
06 Best me ... Practice in Steel Construction - INDUSTriAL Buildings
Application Benefits:
• Maximum storage density
• Building use is unaffected
by the structure
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
• Cheapest construction
method for high-
bay warehouse
• Short construction period
• Fast return of
capital investment
Dm-drogerie markt – one of the leading The commissioning store was a rack-
drugstore chains in Europe – operates supported storage system, named because
over 1,500 retail outlets and employs the construction of the steel racks also acts
some 20,000 people. With a turnover of as the main support structure for roof and
almost 3 billion Euros, dm-drogerie markt wall. Roof and wall cladding were rapidly
offers a range of some 12,000 product attached to the racking construction parallel
lines. In 2003, dm-drogerie markt decided to the assembly. Compared to traditional
to build a further logistics facility in solutions comprising a main support
Waghäusel, located in southern Germany structure and racks that only support
between Karlsruhe and Mannheim. themselves, the construction period was
significantly shorter, thus achieving an
The distribution centre is divided into earlier return of the investment.
four main parts. While the building for
incoming and outgoing goods, servicing Apart from the short construction period
rooms, as well as offices, social rooms and the comparatively low cost, the
and canteen were built in reinforced significantly shorter amortization period is
concrete, the heart of the complex, an additional advantage. However, the
the commission store, is built in steel. racking system had to be designed taking
The commission store is 90 m long, into account the additional load cases due
125 m wide and 20 m high and it to the self-weight of the building envelope
Created on 30 March 2011
provides space for 24,024 commissioning and imposed wind and snow loads.
and storage bins.
56 EURO-BUILD in Steel
EP37 Best Practice in Steel Construction - Industrial Buildings
Swisslog AG, Buchs, Switzerland isolated cassette elements. The interior The fire walls reach up to 0.5 m above
Steel Construction: cassettes were attached to the gable the roof of the ingoing/outgoing goods
Nedcon Magazijninrichting B.V, columns and the columns of the long- store. Furthermore, an impact resistant
Doetinchem, Netherlands itudinal walls. The roof beams were roof strip made of reinforced concrete
Fire Engineering: arranged in accordance with the division was erected to prevent the fire spread
Brandschutz Hoffmann, Worms of the racks in the longitudinal direction at between commissioning store and hall
Building Services: a spacing of 3.14 m. An extensive ‘green’ for incoming/outgoing goods.
AXIMA GmbH, Karlsruhe roof was achieved using steel sheeting,
100 mm of thermal insulation, a sealant Both the commissioning store and the
layer and soil covering. incoming/outgoing goods store are
Building Facts equipped with full sprinkler systems,
Construction period: There are a total of 5 stair towers with additional in-rack sprinklers in the
2003-2004 in reinforced concrete with a fire commissioning store. In addition, an
Site area: resistance of 90 minutes. At the rear automatic fire alarm system was installed.
70,000 m² wall, external escape catwalks made
Commissioning store:
200,000 m³
Hall for incoming/ outgoing goods:
4,500 m²
Created on 30 March 2011
EURO-BUILD in Steel 57
EP37 Best Practice in Steel Construction - Industrial Buildings
Discuss me ...
ArcelorMittal
Long Carbon, Research and Development,
66, rue de Luxembourg, L - 4009 Esch/Alzette, Luxembourg
www.arcelormittal.com
Labein - Tecnalia
C/Geldo – Parque Tecnológico de Bizkaia – Edificio 700,
48160 Derio, Bizkaia, Spain
www.labein.es
SBI
Vasagatan 52, SE - 111 20 Stockholm,
Sweden
www.sbi.se