Professional Documents
Culture Documents
3AH3 - VCB Manual PDF
3AH3 - VCB Manual PDF
7.2kV to 36kV
3AH3
7.2kV 36kV
General: :
Siemens 3AH3 vacuum circuit-breakers (V- 3AH3 ,
breaker) are of the triple-pole indoor type for rated 7.2kV 36kV.
voltages between 7.2 and 36kV.
- 1/1 -
Basic type
Rated voltage
3 A H 3 1 1 7 - 7
(See catalog HG11 for selection and ordering data of ( 11)
the respective circuit-breaker)
Rating plate
3117-7 2Y 3117-7 2Y
3150 3150
50 50
O- O-
Fig.1/1 .1/1
Rating plate
Note: in the event of any queries state the type : (2), (4),
designation(2), designation code(4) and the serial (3).
number(3).
- 1/2 -
Load current A
1250A 2
2000A 4
2500A 5
3150A 6
4000A 7
Ambient temperature °C
Fig.1/2 Maximum permissible load current as a function of the
switch ambient temperature
. 1/2
-1/3 -
¬ - ® ¯ ° ± ² ³ ´ µ (11)
Note: available :
1. Rated voltage (maximum permissible system voltage) at 50 to 1. ( ) 50-60Hz
60Hz.
2. Rated lightning impulse withstand voltage (peak value) 2. ( )
3. Rated power frequency withstand voltage (RMS value) 3. ( )
4. Rated short-circuit current 4.
5. Rated short-circuit duration 5.
6. Type designation 6.
7. Rated normal current 7.
8. Rated short-circuit making current 8.
9. DC component of rated short-circuit breaking current 9.
10. Pole center distance 10.
11. Switching duties U= Rapid load transfer 11. U=
K= rapid auto-reclosure +U K= +U
E= electrical operating energy E=
- 1/5 -
ms >15
Shortest pulse duration of breaker tripping signal for 1st shunt release /
ms >10
Shortest pulse duration of breaker tripping signal for 2nd and 3rd shunt release
/2 3
Fig.1/5 operating times/ .1/5
*) 8RL74, G
Breaking capacity/
AC 40 to 60 Hz/ 40~60Hz DC/
Voltage Operational current Voltage Operational current/
I (A)
U (V) I (A) U (V) Resistive load/ Inductive load/
(T=20ms)
<230V 10 24 10 10
48 10 9
60 9 7
110 5 4
220 2.5 2
Fig.1/7 Breaking capacity of 3SV92 auxiliary switch
.1/7 3SV92
1 1
) Can be ordered on request, retrofitting possible. ) , .
- 1/8 -
Mechanical interlocking1) .
Operating mechanism of disconnectors can be fitted
1
with a mechanical switchgear interlocking facility. The )
disconnector and the associated circuit-breaker are in .
this case interlocked mechanically. .
The sensing parts check the switch position of the
circuit-breaker and prevent if from closing mechanically
and electrically if the associated disconnector is not in , ,
a position to allow safe operation. On the other hand,
the disconnector is prevented from being operated , . ,
when the circuit-breaker is closed. , .
.
1) Can be ordered on request, retrofitting possible. 1) , .
- 1/9 -
- 2/1 -
Tightening torque:10Nm
: 10Nm
- 2/2 -
- 2/3 -
- 2/4 -
- 2/5 -
On the pole plate (15.) and on the mechanism housing (15.) (60.) 14 –
(60.) there are a total of 14 fixing holes – to suit the ( .3/1). 50
various types of installation (Fig.3/1). For installation of kA .
vacuum circuit breakers with rated short circuit
breaking current > 50kA we recommend to only the
pole plate.
Note: :
Silver-plated parts must not be bolted together with .
aluminium bars.
Use the appropriate M12 nuts and bolts of strength 8 M12 ,
class 8 and corresponding spring elements and plain .
washers.
Control leads
Vacuum circuit-breaker of standard design are 64 X0 (68.7.1).
2
provided with a 64-pole low-voltage plug connector X0 1.5mm
(68.7.1). The corresponding plug for external , .(
connection is designed for crimp connection of control Harting 09 99 000 0110 09 99
2 2
leads with a nominal section area of 1.5mm . Use only 000 0111) ).
crimping tools (e.g. Harting crimp tongs 09 99 000 01
2
10 with positioning sleeve 09 99 000 0111) ).
Earthing
Fig.3/2 70
.3/2
Circuit documents
The wiring and connection of circuit-breaker is shown ,
in the circuit diagram supplied, depending on the .
particular model and complement.
Release "off"
" "
-Y6 -Y5
-Y7
Motor drive Closing and anti- 1st shunt Switch closing spring charged signal
pumping device release tripping signal
⇑
⇑
⇑
⇑
HA Manual tripping/
Fig.3/3 V circuit-breaker 3AH3 with manual and electrical HE Manual closing/
closing with 64-way plug connector K1 Anti-pumping contactor
.3/3 , 64
3AH3 M1 Motor operating mechanism/
P Energy store/
R1 Resistor/
Tripping via S1 Auxiliary switch/
Tripping via NC NC contact S21, S22 Position switches (cut-out motor after
contact
System wiring charging)
( )
S3 Position switches
(open when closing spring charged )
( )
Breaker wiring
S41, S42 Position switch (signals charged state)
( )
S6, S7 Position switches (for switch tripped signal)
( )
X0 Low-voltage plug connector
- 3/3 -
Release "off"
"
-Y6 -Y5
-Y7
Electrical
manual 1st shunt 1st CT operated Switch
Motor drive Closing and anti- Closing spring charged signal
closing release release tripping signal
pumping device
Fig.3/5 V circuit-breaker 3AH3 with electrical manual closing with HA Manual tripping/
64-way plug connector HE Manual closing/
Example for extended fitting with Y4 and varistor circuit for DC K1 Anti-pumping contactor
.3/5 64 3AH3
Y4
M1 Motor operating mechanism/
P Energy store/
R1 Resistor/
S1 Auxiliary switch/
S21, S22 Position switches (cut-out motor after charging)
With this model, the auxiliary switch terminals are wired to the plug connector as illustrated
( )
S3 Position switches
(open when closing spring charged )
Auxiliary switch standard Auxiliary switch extended
( )
S41, S42 Position switches (signals charged state)
( )
S6, S7 Position switches (for switch tripped signal)
( )
X0 Low-voltage plug connector
! WARNING !
This equipment contains hazardous voltages ,
and mechanical parts which move at high .
speed and may be control remotely.
In particular: :
Do not remove the cover (60.1). Do not reach (60.1).
inside any openings in the operating mecha- .
nism. Dot not touch pole assemblies(19.) (19.) (48.).
and operating rods (48.).
Commissioning
! CAUTION !
The V-breaker may be operated only with the ,
original hand crank (50.), in order to avoid (50.).
injures as a result of the motor suddenly
starting up.
4. Charge the closing spring (62.) with the hand crank (50.) 4. (50.) (62.) ( .4/1), ″ ″
(see Fig.4/1), press the ″close″ push-button (53.) and (53.), , ″ ″ (54.) .
after closing, trip the breaker by pressing the ″open″
push-button (54.).
- 4/1 -
6. Check the auxiliary switch S1 (68.) and position switches 6. 3AH3 , S1 (68.)
(50.4.1) electrically in both end positions by actuating the (50.4.1) .
3AH3 vacuum circuit-breaker.
Closing
Tripping
Safety measure
! DANGER !
Maintenance, repair and subsequent conver- ,
sion work may be carried out only by specially .
trained personnel in accordance with the
operating instructions and/or special
conversions instructions. Training and
information sessions for personnel can be
provided by the competent Siemens
department
before starting any work on V-breakers, ,
reference must be made to the local safety , (DIN VDE 0105/07.83
regulations for high-voltage switchgear, e.g. 9 , 1 ).
the five safety rules (DIN VDE 0105/07.83 ( "
Part 1, Item 9). Switch off the power supply " ).
and then close and open the V-breaker by
hand ( V-breaker in open state "closing spring
discharged" indication visible).
Servicing
Cleaning
To ensure the insulating capacity, it is necessary that . .
the insulating components are clean. Insulating .
components and external breaker parts must be wiped .
with a damp cloth. Use only warm water with the
addition of a mild liquid household detergent as
cleaning agent.
! WARNING !
Windings and terminals must not be touched ,
if the power supply has not been disconnect- .
ed.
Non-observance can result in death or
serious personnel injury.
! CAUTION !
All springs of the operating mechanism must ,
be relaxed and the vacuum circuit-breaker ,"
be brought into the open state, "closing spring " .
discharged" indication visible.
Non-observance can result in personnel injury. .
- 5/1 -
Order No
180 g Klber-Isoflex Topas L32 3AX1133-3A 180 g Klber-Isoflex Topas L32 3AX1133-3A
and 50 g SHELL Tellus Oil 32 and 50 g SHELL Tellus Oil 32
180 g Klber-Isoflex Topas L32 3AX1133-3H 180 g Klber-Isoflex Topas L32 3AX1133-3H
1kg SHELL Tellus Oil 32 3AX1133-2D 1kg SHELL Tellus Oil 32 3AX1133-2D
1kg Klber-Isoflex Topas L32 3AX1133-3E 1kg Klber-Isoflex Topas L32 3AX1133-3E
- 5/2 -
- 5/3 -
Rated voltage Rated short-circuit breaking current Load characteristic number at rated normal current
36 31.5 4 4 4 - -
40 5 5 5 -
Number of breaking operations/
3AX 1530-2B :
A hand crank 3AX 1530-2B for charging the closing
spring can be supplied as an accessory:
,
Owing to the fact that all parts of this breaker type have ,
been optimized to the last the normal service life, it is .
not possible to recommend particular spare parts for
keeping in stock.
:
When ordering spare part state the following: 1. 3AH3 , ( ).
1. Type designation, design code and serial number
of the 3AH3 vacuum circuit-breaker (see rating
plate) 2. ,
2. The designation and part number, making , .
reference to illustrations in these operating
instructions or to a photograph or sketch as
applicable. Alternatively, a sample may be
submitted.
Published by the
Power Transmission and Distribution Group
Schaltwerk Berlin Schaltwerk
Translated by
SLC PTD MC
Edition 1/March 2001 1/03/2001
Subject to change
- 5/5 -