Professional Documents
Culture Documents
Dist-003H Shortcut PDF
Dist-003H Shortcut PDF
1. Lesson Objectives
Short cut distillation modeling
Initial column sizing
2. Prerequisites
Aspen HYSYS V8.0
Introduction to vapor liquid equilibrium
3. Background
Short Cut Distillation Block
The Short Cut Column performs Fenske-Underwood short cut calculations for simple refluxed towers. The
Fenske minimum number of trays and the Underwood minimum reflux are calculated. A specified ref lux ratio
can then be used to calculate the vapor and liquid traffic rates in the enriching and stripping sections, the
condenser duty and reboiler duty, the number of ideal trays, and the optimal feed location. The Short Cut
Column is only an estimate of the Column performance and is restricted to simple refluxed Columns. For more
realistic results the rigorous Column operation should be used. This operation can provide initial estimates for
most simple Columns
1
Dist-003H Revised: Nov 7, 2012
The examples presented are solely intended to illustrate specific concepts and principles. They may not
reflect an industrial application or real situation.
4.02. Create a component list. In the Component Lists folder select Add. Add Ethane and Ethylene to the
component list. You may need to type “ethene” in the Search for field to find ethylene.
2
Dist-003H Revised: Nov 7, 2012
4.03. Define property package. In the Fluid Packages folder select Add. Select Peng-Robinson as the
property package.
4.04. Go to the simulation environment by clicking on the Simulation button below the navigation pane.
4.05. Add a Short Cut Distillation model to the flowsheet from the Model Palette.
4.06. Double click on the column (T-100). Create an Inlet called Feed, a Condenser Duty called Q-Cond, a
Distillate called Dist, a Reboiler Duty called Q-Reb, and a Bottoms called Bot. Check the Liquid radio
button under Top Product Phase, which specifies a total condenser.
3
Dist-003H Revised: Nov 7, 2012
4.07. Define feed stream. Go to the Worksheet tab. Enter a Vapour Fraction of 1, a Pressure of 350 psig
(25.14 bar), and a Mass Flow of 7,300,000 lb/day (1.38e+005 kg/h).
4.08. In the Composition form enter Mass Fractions of 0.315 for Ethane and 0.685 for Ethylene. The feed
stream should solve.
4
Dist-003H Revised: Nov 7, 2012
4.09. Go to the Parameters form under the Design tab in the Shortcut Column window. Using the recovery
percentages specified in the problem statement along with a simple mass balance, it can be determined
that the mole fraction of ethane in the distillate stream will be approximately 0.004, and the mole
fraction of ethylene in the bottoms will be approximately 0.002. Enter these values into the
Components grid in the Parameters form.
4.10. Specify the Condenser and Reboiler Pressures to both be 300 psig (21.698 bar). You can see that HYSYS
has now calculated the Minimum Reflux Ratio required to complete the specified separation with an
infinite number of stages.
4.11. You may now enter a Reflux Ratio and the Shortcut Column will calculate the number of stages, feed
stage location, condenser and reboiler temperatures, and material and energy flows. For example,
enter 4.5 as the External Reflux Ratio.
5
Dist-003H Revised: Nov 7, 2012
4.12. In the Performance tab you will see the following results.
6
Dist-003H Revised: Nov 7, 2012
5. Conclusions
Estimation using the Short Cut Column can be done very quickly, even for complex distillation systems. The
results can then be used as a starting point for more complex analysis, such as a with a rigorous distillation
model.
6. Copyright
Copyright © 2012 by Aspen Technology, Inc. (“AspenTech”). All rights reserved. This work may not be
reproduced or distributed in any form or by any means without the prior written consent of
AspenTech. ASPENTECH MAKES NO WARRANTY OR REPRESENTATION, EITHER EXPRESSED OR IMPLIED, WITH
RESPECT TO THIS WORK and assumes no liability for any errors or omissions. In no event will AspenTech be
liable to you for damages, including any loss of profits, lost savings, or other incidental or consequential
damages arising out of the use of the information contained in, or the digital files supplied with or for use with,
this work. This work and its contents are provided for educational purposes only.
AspenTech®, aspenONE®, and the Aspen leaf logo, are trademarks of Aspen Technology, I nc.. Brands and
product names mentioned in this documentation are trademarks or service marks of their respective companies.