Professional Documents
Culture Documents
NOTES
1. Node description
- VB_RLY: Battery voltage supply after main relay
- V_IGK: Battery voltage supply after ignition key
- VBD: Direct battery voltage supply
LSH_UP_PWM
thickness of wiring . 0.5 [mm] is recommended for other
SENS_GND_3
SENS_GND_4
SENS_GND_2
SENS_GND_6
SENS_GND_5
SENS_GND_1
GND_PWR_1
GND_PWR_2
wirings. In case of longer than usual harness or a wire
KNKS_SHD
RLY_MAIN
GND_ECU
CRK_SHD
GND_IGC
with many in-line connector, a sufficient section must be
RLY_EFP
(W_Line)
VB_RLY
VLS_UP
DIAG_K
GND_IV
CRK_B
CRK_A
CAN_H
R_Line
provided.
CAN_L
VCC_3
VCC_1
V_IGK
KNKS
IGC1
IGC2
CAM
1
MAP
TCO
VBD
TPS
TIA
VS
1 3. Red number is corresponding pin number of each
A67 A33 B24 B28 A3 A32 A31 B30 B29 A7 A66 A69 B51 A35 A44 B16 B17 B22 B85 B54 B25 B76 A15 A74 B21 A42A12 A11 B88 B57 B56 A6 component to ECU for paying attention to connection.
A13 A75 B50 B78 B19
1.5
1.5
1.5
1.5
1.5
1.0
1.5
5. Fuse capacities in the diagram are reference values. It
should be determined by customer.
GND
20A
20A
VB_RLY_1
V_IGK VB_RLY_2
10A
Chassis
(Ground) VB_RLY_3 VB_RLY_3 5 8 7
CAN_HIGH
CAN_LOW
15A
Fuel Pump
2
M
VBD
To other CAN Immobilizer
users Control Unit
Signal
GND
Supply
Signal B
Signal A
Supply
Signal
GND
Supply
Supply
Signal
Coil1
GND
supply
GND
Signal
Heater A
Heater B
Signal
GND
Supply
Coil2
Signal
Signal
Signal
GND
GND
8 7 6 5 4 3 2 1
16 15 14 13 12 11 10 9
Battery
(Cyl.2 (Cyl.1 Vehicle Speed terminal(+)
Cyl.3) Cyl.4) CAM Shaft CRK Shaft
Sensor Upstream Knock
Position Position Throttle
Main Relay Fuel Pump Relay Oxygen Engine Coolant Sensor
Sensor Sensor Position
Battery Ignition key TMAP Sensor Sensor Temperature
Dual Relay (Inductive) Sensor
terminal(+) Sensor
RLY_ACCOUT
VEHICLE_SEL
RLY_FAN_H
RLY_FAN_L
HOT_LAMP
STPB_NEG
STPA_NEG
STPB_POS
STPA_POS
DIAG_FAN
PRS_SWT
(Provision)
PRS_ACC
CPPWM
ACIN
ESS
CEL
3
IV1
IV2
IV3
IV4
B59 B90 B60 B89 A73 A61 A62 A1 A2 A71 A39 A10 A45 A9 B52 B87 B23 A41 B83 A68
1.0
1.0
1.0
1.0
Paykan Pickup
only in case of
to Tachometer
(PWM output)
VBD V_IGK
A/C switch
FAN B
V_IGK
VB_RLY_2
V_IGK
FAN A
controller
VB_RLY_2 M
Thermo
V_IGK V_IGK
Compressor
M
A D B C
on
on
sw_b
sw_b
sw_b
sw_c
sw_c
sw_b
on
on
sw_a
sw_a
sw_a
sw_a
On
On
On
On
supply
supply
supply
supply
On
supply
supply
supply
STPB-
supply
supply
STPB+
STPA-
supply
supply
STPA+
On
On
Signal
GND
(default)
(Cyl 1) (Cyl 3) (Cyl 4) (Cyl 2) Canistor Check Hot Lamp
Gasoline Injector Purge Engine
Solenoid Lamp FAN HIGH FAN Control FAN LOW Evaporator AC Compressor Control
Valve Stepper Motor Relay Relay Relay Temperature Relay
Sensor
Status Revision - No. Date Name Description
Date Name Title
Editor 2009.05.08 JY LEE
SIM2K-34VR wiring diagram Sheet
(ROA II) 1/1
Check
A B C D E