Professional Documents
Culture Documents
Mechanical QC Material
Mechanical QC Material
FOR
HPPE WAREHOUSE
CLIENT : SHARQ
Table of Contents
No. Description
A. Scope of Work
B. Applicable Codes & references
C. Abbreviations
D. Materials specifications
E. Load Data
F. Basic Load combinations
G. Prokon input and output data
SAUDI DESIGNERS TITLE CAL BY: NAG Date: 21/01/06
ENGINEERING CONSULTANTS DESIGN CALCULATION DOC NO.
P.O.Box 7953, Dammam-31472, DOC-1 REV:00
FOR
K.S.A
Tel: 8346778, Fax: 8326594 HPPE WAREHOUSE SHEET NO. 3
A. Scope of Work:
• Design Of HPPE warehouse Foundation
C. Abbreviations
• DL - Dead Load
• LL - Live Load
• Lr - roof live load
• COL - Collateral Load
• WIND END - Wind End Load
• WIND LEFT - Wind Left Load
• WIND RIGHT - Wind Right Load
• WL - wind load
• E - indicates seismic load
• SEIS1 - indicates seismic load acting from left
to right.
• SEIS2 - indicates seismic load acting from right
to left.
SAUDI DESIGNERS TITLE CAL BY: NAG Date: 21/01/06
ENGINEERING CONSULTANTS DESIGN CALCULATION DOC NO.
P.O.Box 7953, Dammam-31472, DOC-1 REV:00
FOR
K.S.A
Tel: 8346778, Fax: 8326594 HPPE WAREHOUSE SHEET NO. 5
D. Materials Specifications
i) Concrete
The required compressive strength of concrete after 28 days shall be not less
than 4000 Psi (30Mpa) and shall conform to ASTM C320.
b) All epoxy coated reinforced bars shall conform with ASTM – A775-
94d
• Net allowable bearing pressure 100 kpa at 1.0m depth from existing ground
level ref. to Soil Investigation Report:- by osaimi engineering office
Geotechnic & materials specialists job#2005-72
SAUDI DESIGNERS TITLE CAL BY: NAG Date: 21/01/06
ENGINEERING CONSULTANTS DESIGN CALCULATION DOC NO.
P.O.Box 7953, Dammam-31472, DOC-1 REV:00
FOR
K.S.A
Tel: 8346778, Fax: 8326594 HPPE WAREHOUSE SHEET NO. 6
E. Design Assumptions
• We considered the reactions from Zamil as the basic case of loading and we
applied the ACI code to check the stability of sliding and bearing capacity of
foundation.
SAUDI DESIGNERS TITLE CAL BY: NAG Date: 21/01/06
ENGINEERING CONSULTANTS DESIGN CALCULATION DOC NO.
P.O.Box 7953, Dammam-31472, DOC-1 REV:00
FOR
K.S.A
Tel: 8346778, Fax: 8326594 HPPE WAREHOUSE SHEET NO. 7
F. Load Data
All Load Given By Zamil
REV.1
7 1 1 1.20 59.5 9 0 0
7 1 1 1.20 13 6 0 0
7 1 1 1.60 50 20 0 0
7 1 1 0.80 -85 13 0 0
8 1 1 1.20 59.5 9 0 0
8 1 1 1.20 13 6 0 0
8 1 1 0.50 50 20 0 0
8 1 1 1.60 -8 -6 0 0
9 1 1 1.20 59.5 9 0 0
9 1 1 1.20 13 6 0 0
9 1 1 0.50 50 20 0 0
9 1 1 1.60 -206 -6 0 0
10 1 1 1.20 59.5 9 0 0
10 1 1 1.20 13 6 0 0
10 1 1 0.50 50 20 0 0
10 1 1 1.60 -114 -105 0 0
11 1 1 1.20 59.5 9 0 0
11 1 1 1.20 13 6 0 0
11 1 1 0.50 50 20 0 0
11 1 1 1.60 -85 13 0 0
Job Number Sheet
3143 2
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
Load Col LF LF P Hx Hy Mx My
Case no. ULS ULS (kN) (kN) (kN) (kNm) (kNm)
ovt
12 1 1 1.20 59.5 9 0 0
12 1 1 1.20 13 6 0 0
12 1 1 1.00 -4 -6 0 0
13 1 1 1.20 59.5 9 0 0
13 1 1 1.20 13 6 0 0
13 1 1 1.00 4 6 0 0
14 1 1 0.90 59.5 9 0 0
14 1 1 0.90 13 6 0 0
14 1 1 1.60 -114 -105 0 0
15 1 1 0.90 59.5 9 0 0
15 1 1 0.90 13 6 0 0
15 1 1 1.60 -85 13 0 0
16 1 1 0.90 59.5 9 0 0
16 1 1 0.90 13 6 0 0
16 1 1 1.00 -4 -6 0 0
17 1 1 0.90 59.5 9 0 0
17 1 1 0.90 13 6 0 0
17 1 1 1.00 4 6 0 0
Sketch of Base
C1
X
D1
B
A
Y
Mx
P
Hx
X
Z
Y
Job Number Sheet
3143 3
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
Output for Load Case 1
Output for Load Case 1
Soil pressure (ULS) (kN/m²) 51.71
Soil pressure (SLS) (kN/m²) 36.94
SF overturning (SLS) 23.19
SF overturning (ULS) 23.19
Safety Factor slip (ULS) 14.19
Safety Factor uplift (ULS) >100
Bottom
Design moment X (kNm/m) 12.61
Reinforcement X (mm²/m) 78
Design moment Y (kNm/m) 8.33
Reinforcement Y (mm²/m) 54
Top
Design moment X (kNm/m) 0.00
Reinforcement X (mm²/m) 0
Design moment Y (kNm/m) 0.00
Reinforcement Y (mm²/m) 0
Linear Shear X (MPa) 0.032
vc (MPa) 0.673
Linear Shear Y (MPa) 0.023
vc (MPa) 0.672
Linear Shear Other (MPa) 0.000
Punching Shear (MPa) 0.061
vc (MPa) 1.661
Cost 0.00
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
7 1 1 1.20 59.5 -9 0 0
7 1 1 1.20 13 -6 0 0
7 1 1 1.60 50 -20 0 0
7 1 1 0.80 -114 105 0 0
8 1 1 1.20 59.5 -9 0 0
8 1 1 1.20 13 -6 0 0
8 1 1 0.50 50 -20 0 0
8 1 1 1.60 -8 6 0 0
9 1 1 1.20 59.5 -9 0 0
9 1 1 1.20 13 -6 0 0
9 1 1 0.50 50 -20 0 0
9 1 1 1.60 -206 6 0 0
10 1 1 1.20 59.5 -9 0 0
10 1 1 1.20 13 -6 0 0
10 1 1 0.50 50 -20 0 0
10 1 1 1.60 -85 -13 0 0
11 1 1 1.20 59.5 -9 0 0
11 1 1 1.20 13 -6 0 0
11 1 1 0.50 50 -20 0 0
11 1 1 1.60 -114 105 0 0
Job Number Sheet
3143 21
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
Load Col LF LF P Hx Hy Mx My
Case no. ULS ULS (kN) (kN) (kN) (kNm) (kNm)
ovt
12 1 1 1.20 59.5 -9 0 0
12 1 1 1.20 13 -6 0 0
12 1 1 1.00 4 -6 0 0
13 1 1 1.20 59.5 -9 0 0
13 1 1 1.20 13 -6 0 0
13 1 1 1.00 -4 6 0 0
14 1 1 0.90 59.5 -9 0 0
14 1 1 0.90 13 -6 0 0
14 1 1 1.60 -85 -13 0 0
15 1 1 0.90 59.5 -9 0 0
15 1 1 0.90 13 -6 0 0
15 1 1 1.60 -114 105 0 0
16 1 1 0.90 59.5 -9 0 0
16 1 1 0.90 13 -6 0 0
16 1 1 1.00 4 -6 0 0
17 1 1 0.90 59.5 -9 0 0
17 1 1 0.90 13 -6 0 0
17 1 1 1.00 -4 6 0 0
Sketch of Base
C1
X
D1
B
A
Y
Mx
P
Hx
X
Z
Y
Job Number Sheet
3143 22
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
Output for Load Case 1
Output for Load Case 1
Soil pressure (ULS) (kN/m²) 51.71
Soil pressure (SLS) (kN/m²) 36.94
SF overturning (SLS) 23.19
SF overturning (ULS) 23.19
Safety Factor slip (ULS) 14.19
Safety Factor uplift (ULS) >100
Bottom
Design moment X (kNm/m) 12.61
Reinforcement X (mm²/m) 78
Design moment Y (kNm/m) 8.33
Reinforcement Y (mm²/m) 51
Top
Design moment X (kNm/m) 0.00
Reinforcement X (mm²/m) 0
Design moment Y (kNm/m) 0.00
Reinforcement Y (mm²/m) 0
Linear Shear X (MPa) 0.032
vc (MPa) 0.673
Linear Shear Y (MPa) 0.022
vc (MPa) 0.672
Linear Shear Other (MPa) 0.000
Punching Shear (MPa) 0.058
vc (MPa) 1.661
Cost 0.00
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
0.60 X 0.60 X
2.60
2.60
0.35 0.35
3.00 3.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.50 0.50
7 1 1 1.20 57 0 0 0
7 1 1 1.20 28 0 0 0
7 1 1 1.60 105 0 0 0
7 1 1 0.80 -213 31 0 0
8 1 1 1.20 57 0 0 0
8 1 1 1.20 28 0 0 0
8 1 1 0.50 105 0 0 0
8 1 1 1.60 -197 0 0 0
9 1 1 1.20 57 0 0 0
9 1 1 1.20 28 0 0 0
9 1 1 0.50 105 0 0 0
9 1 1 1.60 -197 0 0 0
10 1 1 1.20 57 0 0 0
10 1 1 1.20 28 0 0 0
10 1 1 0.50 105 0 0 0
10 1 1 1.60 -213 -31 0 0
11 1 1 1.20 57 0 0 0
11 1 1 1.20 28 0 0 0
11 1 1 0.50 105 0 0 0
11 1 1 1.60 -213 31 0 0
Job Number Sheet
3143 40
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
Load Col LF LF P Hx Hy Mx My
Case no. ULS ULS (kN) (kN) (kN) (kNm) (kNm)
ovt
12 1 1 1.20 57 0 0 0
12 1 1 1.20 28 0 0 0
12 1 1 1.00 0 -6 0 0
13 1 1 1.20 57 0 0 0
13 1 1 1.20 28 0 0 0
13 1 1 1.00 0 6 0 0
14 1 1 0.90 57 0 0 0
14 1 1 0.90 28 0 0 0
14 1 1 1.60 -213 -31 0 0
15 1 1 0.90 57 0 0 0
15 1 1 0.90 28 0 0 0
15 1 1 1.60 -213 31 0 0
16 1 1 0.90 57 0 0 0
16 1 1 0.90 28 0 0 0
16 1 1 1.00 0 -6 0 0
17 1 1 0.90 57 0 0 0
17 1 1 0.90 28 0 0 0
17 1 1 1.00 0 6 0 0
Sketch of Base
C1
X
D1
B
A
Y
Mx
P
Hx
X
Z
Y
Job Number Sheet
3143 41
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
Output for Load Case 1
Output for Load Case 1
Soil pressure (ULS) (kN/m²) 58.89
Soil pressure (SLS) (kN/m²) 42.07
SF overturning (SLS) >100
SF overturning (ULS) >100
Safety Factor slip (ULS) >100
Safety Factor uplift (ULS) >100
Bottom
Design moment X (kNm/m) 9.80
Reinforcement X (mm²/m) 60
Design moment Y (kNm/m) 9.35
Reinforcement Y (mm²/m) 58
Top
Design moment X (kNm/m) 0.00
Reinforcement X (mm²/m) 0
Design moment Y (kNm/m) 0.00
Reinforcement Y (mm²/m) 0
Linear Shear X (MPa) 0.026
vc (MPa) 0.673
Linear Shear Y (MPa) 0.025
vc (MPa) 0.672
Linear Shear Other (MPa) 0.000
Punching Shear (MPa) 0.061
vc (MPa) 1.661
Cost 0.00
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
0.70 0.70
X X
2.60
2.60
0.45 0.45
2.90 2.90
Y Y
Mx Mx
P P
Hx Hx
1.00
1.00
1.00 1.00
0.50 0.50
Sketch of Base
Job Number Sheet
3143 59
Job Title
HPPE WAREHOUSE
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com SHARQ
Calcs by Checked by Date
E-Mail : mail@prokon.com NAG YAA 1/21/2006
C1
X
D1
B
A
Y
Mx
P
Hx
X
Z
0.40 X 0.40 X
2.00
2.00
0.30 0.30
2.00 2.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.40 0.40
0.40 X 0.40 X
2.00
2.00
0.30 0.30
2.00 2.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.40 0.40
0.40 X 0.40 X
2.00
2.00
0.30 0.30
2.00 2.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.40 0.40
0.40 X 0.40 X
2.00
2.00
0.30 0.30
2.00 2.00
Y Y
Mx Mx
P P
Hx Hx
0.60
0.60
0.60 0.60
0.40 0.40
I. Foundation Details
See Attachments (B &D)
SAUDI DESIGNERS TITLE CAL BY: NAG Date: 21/01/06
ENGINEERING CONSULTANTS DESIGN CALCULATION DOC NO.
P.O.Box 7953, Dammam-31472, DOC-1 REV:00
FOR
K.S.A
Tel: 8346778, Fax: 8326594 HPPE WAREHOUSE SHEET NO. 11
G. PEDESTAL DESIGN
y
x
Bars: User-defined
Date: 12/13/05
Time: 09:13:38
-400
P = 0 kN
PCACOL V3.00 (PCA 1999) - Licensed to: Your company name, City, ST
File: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Column: P1 Engineer: ng
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Project: HPPE WAREHOUSE
Column: P1 Engineer: ng
Code: ACI 318-95 Units: Metric
Material Properties:
====================
f'c = 25 MPa fy = 400 MPa
Ec = 23500 MPa Es = 200000 MPa
fc = 21.25 MPa Rupture strain = Infinity
Ultimate strain = 0.003 mm/mm
Beta1 = 0.85
Section:
========
Rectangular: Width = 350 mm Depth = 600 mm
Reinforcement:
==============
Rebar Database: User-defined
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 6 6 28 # 8 8 50 # 10 10 79
# 12 12 113 # 14 14 154 # 16 16 201
# 18 18 254 # 20 20 314 # 25 25 491
# 28 28 616 # 32 32 801 # 40 40 1256
Confinement: Tied; #10 ties with #20 bars, #10 with larger bars.
phi(a) = 0.8, phi(b) = 0.9, phi(c) = 0.7
Layout: Rectangular
Pattern: Equal Bar Spacing (Cover to transverse reinforcement)
Total steel area, As = 2412 mm^2 at 1.15%
12 #16 Cover = 30 mm
Control Points:
===============
Axial Load P X-Moment Y-Moment N.A. depth
Bending about kN kN-m kN-m mm
--------------------- ------------ ------------ ------------ -----------
X @ Pure compression 3763.2 0 0 1656
@ Max compression 3010.6 174 0 592
@ fs = 0.0 2812.9 209 0 552
@ fs = 0.5*fy 2035.0 301 -0 414
@ Balanced point 1492.5 332 -0 331
@ Pure bending 0.0 224 -0 90
@ Pure tension -868.3 0 0 0
y
x
Bars: User-defined
Date: 12/13/05
Time: 09:16:16
-600
P = 0 kN
PCACOL V3.00 (PCA 1999) - Licensed to: Your company name, City, ST
File: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Column: P2 Engineer: ng
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Project: HPPE WAREHOUSE
Column: P2 Engineer: ng
Code: ACI 318-95 Units: Metric
Material Properties:
====================
f'c = 25 MPa fy = 400 MPa
Ec = 23500 MPa Es = 200000 MPa
fc = 21.25 MPa Rupture strain = Infinity
Ultimate strain = 0.003 mm/mm
Beta1 = 0.85
Section:
========
Rectangular: Width = 450 mm Depth = 700 mm
Reinforcement:
==============
Rebar Database: User-defined
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 6 6 28 # 8 8 50 # 10 10 79
# 12 12 113 # 14 14 154 # 16 16 201
# 18 18 254 # 20 20 314 # 25 25 491
# 28 28 616 # 32 32 801 # 40 40 1256
Confinement: Tied; #10 ties with #20 bars, #10 with larger bars.
phi(a) = 0.8, phi(b) = 0.9, phi(c) = 0.7
Layout: Rectangular
Pattern: Equal Bar Spacing (Cover to transverse reinforcement)
Total steel area, As = 3216 mm^2 at 1.02%
16 #16 Cover = 30 mm
Control Points:
===============
Axial Load P X-Moment Y-Moment N.A. depth
Bending about kN kN-m kN-m mm
--------------------- ------------ ------------ ------------ -----------
X @ Pure compression 5538.3 0 0 1956
@ Max compression 4430.6 302 0 689
@ fs = 0.0 4199.2 351 0 652
@ fs = 0.5*fy 3056.9 518 -0 489
@ Balanced point 2273.0 571 -0 391
@ Pure bending 0.0 356 0 92
@ Pure tension -1157.8 -0 0 0
y
x
Bars: User-defined
Date: 12/13/05
Time: 09:17:16
-200
P = 0 kN
PCACOL V3.00 (PCA 1999) - Licensed to: Your company name, City, ST
File: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Column: P3 Engineer: ng
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Project: HPPE WAREHOUSE
Column: P3 Engineer: ng
Code: ACI 318-95 Units: Metric
Material Properties:
====================
f'c = 25 MPa fy = 400 MPa
Ec = 23500 MPa Es = 200000 MPa
fc = 21.25 MPa Rupture strain = Infinity
Ultimate strain = 0.003 mm/mm
Beta1 = 0.85
Section:
========
Rectangular: Width = 300 mm Depth = 400 mm
Reinforcement:
==============
Rebar Database: User-defined
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 6 6 28 # 8 8 50 # 10 10 79
# 12 12 113 # 14 14 154 # 16 16 201
# 18 18 254 # 20 20 314 # 25 25 491
# 28 28 616 # 32 32 801 # 40 40 1256
Confinement: Tied; #10 ties with #20 bars, #10 with larger bars.
phi(a) = 0.8, phi(b) = 0.9, phi(c) = 0.7
Layout: Rectangular
Pattern: Equal Bar Spacing (Cover to transverse reinforcement)
Total steel area, As = 1608 mm^2 at 1.34%
8 #16 Cover = 30 mm
Control Points:
===============
Axial Load P X-Moment Y-Moment N.A. depth
Bending about kN kN-m kN-m mm
--------------------- ------------ ------------ ------------ -----------
X @ Pure compression 2211.3 -0 0 1056
@ Max compression 1769.1 68 0 398
@ fs = 0.0 1562.0 92 0 352
@ fs = 0.5*fy 1111.8 125 0 264
@ Balanced point 795.1 138 0 211
@ Pure bending 0.0 95 0 62
@ Pure tension -578.9 0 0 0
y
x
Bars: User-defined
Date: 12/13/05
Time: 09:18:31
-800
P = 0 kN
PCACOL V3.00 (PCA 1999) - Licensed to: Your company name, City, ST
File: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Column: P4 Engineer: ng
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\PROGRA~1\PCACOL\DATA\P1L.COL
Project: HPPE WAREHOUSE
Column: P4 Engineer: ng
Code: ACI 318-95 Units: Metric
Material Properties:
====================
f'c = 25 MPa fy = 400 MPa
Ec = 23500 MPa Es = 200000 MPa
fc = 21.25 MPa Rupture strain = Infinity
Ultimate strain = 0.003 mm/mm
Beta1 = 0.85
Section:
========
Rectangular: Width = 600 mm Depth = 700 mm
Reinforcement:
==============
Rebar Database: User-defined
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 6 6 28 # 8 8 50 # 10 10 79
# 12 12 113 # 14 14 154 # 16 16 201
# 18 18 254 # 20 20 314 # 25 25 491
# 28 28 616 # 32 32 801 # 40 40 1256
Confinement: Tied; #10 ties with #20 bars, #10 with larger bars.
phi(a) = 0.8, phi(b) = 0.9, phi(c) = 0.7
Layout: Rectangular
Pattern: Equal Bar Spacing (Cover to transverse reinforcement)
Total steel area, As = 4572 mm^2 at 1.09%
18 #18 Cover = 30 mm
Control Points:
===============
Axial Load P X-Moment Y-Moment N.A. depth
Bending about kN kN-m kN-m mm
--------------------- ------------ ------------ ------------ -----------
X @ Pure compression 7459.7 -0 0 1953
@ Max compression 5967.7 411 0 692
@ fs = 0.0 5624.1 484 0 651
@ fs = 0.5*fy 4081.9 713 0 488
@ Balanced point 3017.9 791 0 391
@ Pure bending 0.0 504 0 92
@ Pure tension -1645.9 -0 0 0