Professional Documents
Culture Documents
Butt Weld Stainless Steel Fittings PDF
Butt Weld Stainless Steel Fittings PDF
INCHES/METRIC
1. Bevels and lands accurately machined for good welding.
2. True diameter maintained throughout the smooth bore for unrestricted flow.
5. Clear identification of size, schedule or nominal wall thickness, material and heat code.
•2•
STAINLESS STEEL
WELDING FITTINGS
INDEX
90˚ Elbows, Long Radius
Schedules 5S, 10S, 40S, 80S...............................................................................Page 6
Caps
Schedules 5S, 10S, 40S, 80S.............................................................................Page 14
Tolerances ....................................................................................................................Page 5
•3•
MATERIAL AND
MANUFACTURING
SPECIFICATIONS
CCTF Stainless Steel Welding Fittings are manufactured in accordance
with the material specifications of ASTM A-403.
This chart gives the Mechanical and Chemical properties of some of the
most widely used alloys.
Mechanical *Chemical
El. 2in.
Tensile Yield
ANSI Corrosion 50mm
Strength Strength
Pressure Resistant KSI min. KSI min. % C Mn P S SI Ni Cr Mo Ti Co
Fittings Fittings (MPa min.) (MPa min.) Longt.
WP 304 CR 304 75 (515) 30 (205) 35 .08 2.0 0.45 0.30 1.00 8.0-11.0 18.0-20.0
WP 304H CR 304H 75 (515) 30 (205) 35 .04-1.0 2.0 0.45 .030 1.00 8.0-11.0 18.0-20.0
WP 304L CR 304L 70 (485) 25 (170) 35 .035d 2.0 .045 .030 1.00 8.0-13.0 18.0-20.0
WP 316 CR 316 75 (515) 30 (205) 35 .08 2.0 0.45 .030 1.00 10.0-14.0 16.0-18.0 2.0-3.0
WP 316H CR 316H 75 (515) 30 (205) 35 .04-.10 2.0 0.45 .030 1.00 10.0-14.0 16.0-18.0 2.0-3.0
WP 316L CR 316L 70 (485) 25 (170) 35 .035d 2.0 .045 .030 1.00 10.0-16.0 16.0-18.0 2.0-3.0
WP 321 CR 321 75 (515) 30 (205) 35 .08 2.0 0.45 .030 1.00 9.0-13.0 17.0-20.0 e
WP 321H CR 321H 75 (515) 30 (205) 35 .04-.10 2.0 0.45 .030 1.00 9.0-13.0 17.0-20.0 c
WP 347 CR 347 75 (515) 30 (205) 35 .08 2.0 0.45 .030 1.00 9.0-13.0 17.0-20.0 a
WP 347H CR 347H 75 (515) 30 (205) 35 .04-.10 2.0 0.45 .030 1.00 9.0-13.0 17.0-20.0 b
* Maximum values except as indicated. b The columbium plus tantalum content shall not be less than eight times the
carbon content and not more than 1.0 per cent.
See appropriate spec. for exact values.
d For small diameter or thin walls or both, where many drawing passes are
e The titanium content shall not be less than five times the carbon content and
required, a carbon maximum of .040 per cent is necessary in grades WP 304L
not more than .70 per cent.
and WP 316L. Small outside diameter tubes are defined as those less than
a The columbium plus tantalum content shall not be less than ten times the .500 in. (12.7 mm) in outside diameter and light wall tubes as those less than
carbon content and not more than 1.10 per cent. .049 in. (1.24 mm) in average wall thickness (.044 in. (1.12mm) in minimum
c The titanium content shall not be less than four times the carbon content and wall thickness).
not more than .70 per cent.
For the appropriate grade of stainless steel for use with corrosive liquids and gases at various temperatures and
pressures, consult your nearest CCTF office.
CCTF Stainless Steel Welding Fittings also conform with one or more of the following standards:
MSS SP-43 Schedules 5s and 10s only ASME/ANSI B36.19M Stainless Steel Pipe
ASME/ANSI B16.9 Welding Fittings, except short radius ASME/ANSI B16.28 Short Radius Elbows and Returns
•4•
MATERIAL AND
MANUFACTURING
The International System (SI) metric equivalent of British SPECIFICATIONS
units are shown throughout this catalogue.
NPS (Nominal Pipe Size) = DN*, (Nominal Diameter)
Operating Pressure Class = PN*, (Pressure Number)
1 inch = 25.4 millimetres
1 pound, weight = 0.4536 kilograms
1 pound, pressure = 0.06895 bars
* From the SI designations, Diamètre Nominal and
Pression Nominale
(1) Dimensional Tolerances MSS SP-43
90˚ & 45˚ Reducers,
All Fittings Elbows, (2)
Lap-Joint
Lap-Joint Caps
Tees, Stub Ends
Stub Ends
Crosses
* Centre to end dimension A for NPS 3/4 (DN 20) may be 1.50 (38mm) at
the manufacturer’s option.
INCHES POUNDS
•6• MILLIMETRES KILOGRAMS
90˚ ELBOW
LONG RADIUS
Schedules 5S, 10S, 40S, 80S
ASME/ANSI B16.28
Schedule 5S Schedule 10S Schedule 40S Schedule 80S
NPS Outside Center Inside Wall Inside Wall Inside Wall Inside Wall
Diameter To End Diameter Thickness Approx. Diameter Thickness Approx. Diameter Thickness Approx. Diameter Thickness Approx.
DN O.D. B I.D. T WT. I.D. T WT. I.D. T WT. I.D. T WT.
1 1.32 1.00 1.185 .065 .12 1.097 .109 .23 1.049 .133 .25 .957 .179 .41
25 33 25 30.10 1.65 .05 27.85 2.75 .1 26.65 3.40 .11 24.30 4.55 .18
1 1/4 1.66 1.25 1.530 .065 .25 1.442 .109 .38 1.380 .140 .40 1.278 .191 .63
32 42 32 38.85 1.65 .11 36.65 2.75 .17 35.05 3.55 .18 32.45 4.85 .28
1 1/2 1.90 1.50 1.770 .065 .42 1.682 .109 .49 1.610 .145 .56 1.500 .200 .75
40 48 38 44.95 1.65 .19 42.70 2.75 .22 40.90 3.70 .25 38.10 5.10 .34
2 2.38 2.00 2.245 .065 .63 2.157 .109 .81 2.067 .154 1 1.939 .218 1.5
50 60 51 57.00 1.65 .28 54.80 2.75 .36 52.50 3.90 .45 49.25 5.55 .68
2 1/2 2.88 2.50 2.709 .083 1.22 2.635 .120 1.36 2.469 .203 2.13 2.323 .276 2.8
65 73 64 68.80 2.10 .55 66.95 3.05 .6 62.70 5.15 .96 59.00 7.00 1.3
3 3.50 3.00 3.334 .083 1.7 3.260 .120 2.17 3.068 .216 3 2.900 .300 4.25
80 89 76 84.70 2.10 .8 82.80 3.05 1.0 77.95 5.50 1.4 73.65 7.60 1.9
3 1/2 4.00 3.50 3.834 .083 2.3 3.760 .120 3.03 3.548 .226 4.5 3.364 .318 6
90 102 89 97.40 2.10 1.0 95.50 3.05 1.4 90.10 5.75 2 85.45 8.10 2.7
4 4.50 4.00 4.334 .083 2.95 4.260 .120 3.8 4.026 .237 6.25 3.826 .337 8.5
100 114 102 100.10 2.10 1.3 108.20 3.05 1.7 102.25 6.00 2.8 97.20 8.55 3.8
5 5.56 5.00 5.345 .109 4.24 5.295 .134 5.19 5.047 .258 9.6 4.813 .375 14
125 141 127 135.75 2.75 1.9 134.50 3.40 2.3 128.20 6.55 4.3 122.25 9.55 6.3
6 6.62 6.00 6.407 .109 6.09 6.357 .134 7.45 6.065 .280 18 5.761 .432 23
150 168 152 162.75 2.75 2.7 161.50 3.40 3.4 154.05 7.10 8.1 146.35 10.95 10.4
INCHES POUNDS
MILLIMETRES KILOGRAMS •7•
45˚ ELBOW
LONG RADIUS
Schedules 5S, 10S, 40S, 80S
MSS SP-43
ASME/ANSI B16.9
* Centre to end dimension B for NPS 3/4 (DN 20) may be 0.75 (19mm) at
the manufacturer’s option.
INCHES POUNDS
•8• MILLIMETRES KILOGRAMS
STRAIGHT &
REDUCING TEES
Schedules 5S, 10S, 40S, 80S
MSS SP-43
ASME/ANSI B.16.9
Centre to End Approximate Weight
O.D. O.D.
MSS SP-43 ANSI B16.9
NPS Outside Outside
DN Dia. Run Dia. Outlet C M SCH. 5S SCH. 10S SCH. 40S SCH. 80S
1/2 straight .84 .84 1.00 1.00 .18 .20 .35 .45
15 straight 21 21 25 25 .08 .09 .16 .2
3/4 x 3/4 x 1/2 1.05 .84 1.12 1.12 .25 .28 .5 .5
20 x 20 x 15 27 21 29 29 .11 .13 .23 .23
3/4 straight 1.05 1.05 1.12 1.12 .21 .28 .45 .6
20 straight 27 27 29 29 .09 .13 .20 .27
1 x 1 x 1/2 1.32 .84 1.50 1.50 .43 .56 .88 1
25 x 25 x 15 33 21 38 38 .19 .25 .40 .45
1 x 1 x 3/4 1.32 1.05 1.50 1.50 .46 .60 .93 1
25 x 25 x 20 33 27 38 38 .21 .27 .42 .45
1 straight 1.32 1.32 1.50 1.50 .35 .60 .75 .88
25 straight 33 33 38 38 .16 .27 .34 .40
1 1/4 x 1 1/4 x 1/2 1.66 .84 1.88 1.88 .65 1.06 1.5 1.75
32 x 32 x 15 42 21 48 48 .29 .48 .68 .79
1 1/4 x 1 1/4 x 3/4 1.66 1.05 1.88 1.88 .67 1.1 1.5 1.75
32 x 32 x 20 42 27 48 48 .30 .50 .68 .79
1 1/4 x 1 1/4 x 1 1.66 1.32 1.88 1.88 .69 1.15 1.5 1.75
32 x 32 x 25 42 33 48 48 .31 .52 .68 .79
1 1/4 straight 1.66 1.66 1.88 1.88 .65 1.1 1.3 1.6
32 straight 42 42 48 48 .29 .50 .59 .72
1 1/2 x 1 1/2 x 1/2 1.90 .84 2.25 2.25 .79 1.33 2 2.5
40 x 40 x 15 48 21 57 57 .36 .60 .9 1.1
1 1/2 x 1 1/2 x 3/4 1.90 1.05 2.25 2.25 .84 1.41 2.13 2.5
40 x 40 x 20 48 27 57 57 .38 .63 .96 1.1
1 1/2 x 1 1/2 x 1 1.90 1.32 2.25 2.25 .86 1.45 2.18 2.5
40 x 40 x 25 48 33 57 57 .39 .65 .98 1.1
1 1/2 x 1 1/2 x 1 1/4 1.90 1.66 2.25 2.25 .89 1.50 2.25 2.5
40 x 40 x 32 48 42 57 57 .40 .68 1.0 1.1
1 1/2 straight 1.90 1.90 2.25 2.25 .89 1.5 2 2.25
40 straight 48 48 57 57 .40 .68 .9 1.0
2 x 2 x 3/4 2.38 1.05 2.50 1.75 .93 1.37 3.25 4
50 x 50 x 20 60 27 64 44 .42 .62 1.46 1.8
2x2x1 2.38 1.32 2.50 2.00 1.0 1.67 3.50 4.1
50 x 50 x 25 60 33 64 51 .45 .75 1.58 1.9
INCHES POUNDS
MILLIMETRES KILOGRAMS •9•
STRAIGHT & REDUCING TEES continued
Centre to End Approximate Weight
MSS SP-43 ANSI B16.9
NPS Outside Outside
DN Dia. Run Dia. Outlet C M SCH. 5S SCH. 10S SCH. 40S SCH. 80S
2 x 2 x 1 1/4 2.38 1.66 2.50 2.25 1.02 1.72 3.6 4.13
50 x 50 x 32 60 42 64 57 .5 .8 1.6 1.9
2 x 2 x 1 1/2 2.38 1.90 2.50 2.38 1.07 1.8 3.75 4.25
50 x 50 x 40 60 48 64 60 .5 .8 1.7 1.9
2 straight 2.38 2.38 2.50 2.50 1.07 1.8 3.5 4
50 straight 60 60 64 64 .5 .8 1.6 1.8
2 1/2 x 2 1/2 x 1 2.88 1.32 3.00 2.25 1.48 2.49 5 7
65 x 65 x 25 73 33 76 57 .7 1.1 2.3 3.2
2 1/2 x 2 1/2 x 1 1/4 2.88 1.66 3.00 2.50 1.55 2.62 5.25 7.06
65 x 65 x 32 73 42 76 64 .7 1.2 2.4 3.2
2 1/2 x 2 1/2 x 1 1/2 2.88 1.90 3.00 2.62 1.63 2.74 5.5 7.13
65 x 65 x 40 73 48 76 67 .7 1.2 2.5 3.2
2 1/2 x 2 1/2 x 2 2.88 2.38 3.00 2.75 1.78 3 6 7.19
65 x 65 x 50 73 60 76 70 .8 1.4 2.7 3.2
2 1/2 straight 2.88 2.88 3.00 3.00 2.07 3 6 7
65 straight 73 73 76 76 .9 1.4 2.7 3.2
3 x 3 x 1 1/4 3.50 1.66 3.38 2.75 2.47 3.61 6.25 7.6
80 x 80 x 32 89 42 86 70 1.1 1.6 2.8 3.4
3 x 3 x 1 1/2 3.50 1.90 3.38 2.88 2.47 3.65 6.25 7.68
80 x 80 x 40 89 48 86 73 1.1 1.6 2.8 3.5
3x3x2 3.50 2.38 3.38 3.00 2.57 3.75 6.5 8
80 x 80 x 50 89 60 86 76 1.2 1.7 2.9 3.6
3 x 3 x 2 1/2 3.50 2.88 3.38 3.25 2.69 3.9 6.75 8.25
80 x 80 x 65 89 73 86 83 1.2 1.8 3 3.7
3 straight 3.50 3.50 3.38 3.38 2.69 3.9 7 8.5
80 straight 89 89 86 86 1.2 1.8 3.2 3.8
3 1/2 x 3 1/2 x 1 1/2 4.00 1.90 3.75 3.12 3.08 4.2 8 11.5
90 x 90 x 40 102 48 95 79 1.4 1.9 3.6 5.2
3 1/2 x 3 1/2 x 2 4.00 2.38 3.75 3.25 3.19 4.49 8.3 11.8
90 x 90 x 50 102 60 95 83 1.4 2 3.7 5.3
3 1/2 x 3 1/2 x 2 1/2 4.00 2.88 3.75 3.50 3.26 4.73 8.5 12.2
90 x 90 x 65 102 73 95 89 1.5 2.1 3.8 5.5
3 1/2 x 3 1/2 x 3 4.00 3.50 3.75 3.62 3.38 4.9 8.8 12.6
90 x 90 x 80 102 89 95 92 1.5 2.2 4 5.7
3 1/2 straight 4.00 4.00 3.75 3.75 3.38 4.9 9 12
90 straight 102 102 95 95 1.5 2.2 4 5.4
4 x 4 x 1 1/2 4.50 1.90 4.12 3.38 3.7 5.38 11.1 15.2
100 x 100 x 40 114 48 105 86 1.7 2.4 5 6.8
4x4x2 4.50 2.38 4.12 3.50 3.75 5.43 11.2 15.5
100 x 100 x 50 114 60 105 89 1.7 2.4 5 7
4 x 4 x 2 1/2 4.50 2.88 4.12 3.75 3.77 5.45 11.3 15.5
100 x 100 x 65 114 73 105 95 1.7 2.5 5.1 7
4x4x3 4.50 3.50 4.12 3.88 3.88 5.6 11.6 15.6
100 x 100 x 80 114 89 105 98 1.8 2.5 5.2 7
4 x 4 x 3 1/2 4.50 4.00 4.12 4.00 3.94 5.7 11.8 15.6
100 x 100 x 90 114 102 105 102 1.8 2.6 5.3 7
4 straight 4.50 4.50 4.12 4.12 3.94 5.7 12 15.7
100 straight 114 114 105 105 1.8 2.6 5.4 7.1
INCHES POUNDS
MILLIMETRES KILOGRAMS • 13 •
▲
CAPS
Schedules 5S, 10S, 40S, 80S
MSS SP-43
ASME/ANSI B16.9
INCHES POUNDS
• 14 • MILLIMETRES KILOGRAMS
LAP JOINT STUB ENDS
Type A (1)
INCHES
• 16 • MILLIMETRES
SSWF