Professional Documents
Culture Documents
www.Broadcast-Devices.com
Table of Contents
I. Introduction
II. Specifications
III. Installation
IV. Warranty
V. Schematic Diagrams
A. Functional Diagram
B. Setup Diagram
C. CTD-300 Schematics
Introduction
The CTD-300 Composite Decoder/AES Generator is intended to be used to convert an analog composite
base band stereo waveform into a pair of AES3 digital outputs. The CTD-300 will accept the selected
composite signal, decode it back to left/right which with proper jumper selection can be routed to the rear
panel XLR connectors or convert it to a pair of AES3 compatible streams suitable for input to digital
exciter equipment. Suggested uses include converting any composite stereo generator or STL to an AES
signal compatible with modern digital AM/FM digital exciters. Analog output is a balanced +4 dBm
left/right output for analog decoder applications if AES output is not needed. See the setup diagram at rear
of this manual for more information.
Carefully unpack the unit after receipt and inspect for damage that may have occurred during shipping. If
damage is noted, contact the shipper immediately and file a damage claim. The contents of the package
have been insured to cover total replacement cost. Make certain that the package contents are the same as
noted on the packing slip. If not, contact Broadcast Devices, Inc.
General Description
The CTD-300 contains a high quality, phase locked loop stereo decoder, analog to digital converter and
AES transmitter. Stereo composite audio is routed to the stereo decoder where it is converted back to
analog left/right and then routed to a 24 bit analog to digital converter. The output of the converter is then
routed to an AES transmitter/DA where it is outputted on a pair of XLR connectors at the rear of the
chassis. In this configuration it is possible to drive a pair of digital input exciters simultaneously with the
same composite source. It is also possible to output a balanced +4 dBm left/right output to the XLR
connectors if AES output is not needed.
Specifications
Composite Input Impedance: 100K unbalanced – Accepts 3.5 Volt RMS composite
Output Impedance: 110 ohm balanced - digital 600 ohms balanced – analog
Number of outputs: 2 – AES3 or 1 – analog left/right
Sample rate: 32, 44.1, 48 or 96 KHz
Pre/de emphasis: 50 or 75uS selectable.
II. Installation
1. Apply normal composite level audio to the B.N.C. connector input. Connect the AES outputs to
suitable AES equipped exciters or BDI AES-302 digital audio switcher/DA and observe
modulation on a suitable modulation monitor. If level adjustment is necessary, there are two
options for adjusting level. If the overall level needs adjustment, turn VR1 up or down as
necessary to maintain desired modulation level. If balance between left and right channels is not
correct, this can be compensated for by adjusting VR2 and 3. VR2 is left channel and VR3 is right
channel. Refer to the setup diagram at the rear of the manual for location of these controls.
2. The CTD-1/SDM-1 is normally shipped from the factory with 75 uS pre and de emphasis
capability for North American applications and 50 uS for European applications. Jumpers JP3, 4
are installed for pre emphasis. In the case of 50 uS pre emphasis a pair of capacitors is supplied to
be placed across JP3 and JP4. These capacitor jumpers are found in a plastic bag inside the unit.
For de emphasized or flat frequency response audio output, remove jumpers JP3 and JP4.Pre
emphasis is defeated as a factory default.
3. Sample rate adjustment. The CTD-300 is normally shipped configured for 44.1 KHz sample rate.
Other sample rates are possible including 32, 48 and 96 KHz. To adjust sample rate to other than
44.1 KHz, consult the sample rate chart on the setup diagram page at the rear of the manual.
Broadcast Devices, Inc. products are warranted against failure due to faulty materials or workmanship for
a period of one year from the date of shipment to the ultimate user. The warranty covers repair or
replacement of defective parts at the factory, provided the unit has been returned prepaid by the user. All
shipments to the factory shall have affixed to the outside of the container an R. A. number obtained from
the factory. The above warranty is void if the unit has been modified by the user outside of any
recommendations from the factory or if the unit has been abused or operated outside of its electrical or
environmental specifications. If customer conducted field tests suggest that the unit may be faulty, whether
or not the unit is in warranty, a full report of the difficulty should be sent to Broadcast Devices, Inc. factory
at Cortlandt Manor, New York. The office may suggest further tests or authorize return for factory
evaluation.
Units sent to the factory should be well packed and shipped to Broadcast Devices, Inc. 5 Crestview
Avenue, Cortlandt Manor, NY 10567. Remember to affix the R.A. number to the outside of the carton.
Any packages received without such R.A. number will be refused. Note: freight collect shipments will also
be refused. When the unit has been received, inspected and tested, the customer will receive a report of the
findings along with a quotation for recommended repairs, which are found falling outside of the standard
warranty. Units returned for in-warranty repairs which are found not to be defective will be subject to an
evaluation and handling charge. In-warranty units will be repaired at no charge and returned via prepaid
freight.
Out-of-warranty units needing repair require a purchase order and will be invoiced for parts, labor, and
shipping charges.
When ordering replacement part, always specify A) Part number or Description, and Quantity; B) Date of
Purchase, Where Purchased; C) Any Special Shipping Instructions. Always specify a street address, as
shipping companies cannot deliver to a postal box.
Broadcast Devices, Inc. is not responsible for any other manufacturer’s warranty on original equipment.
Nor are we responsible for any failure, damage, or loss of property that may occur due to the installation or
operation of our equipment outside of recommended specifications.
V. Schematic Diagrams
A. Functional Diagram
B. Setup Diagram
C. CTD-300 Schematic
5 4 3 2 1
L1A
2
J1
D L1D D
Left Output 2 T2 3
1 8
4
Analog Pre emphasis ADC/AES Transmitters 6
Schott-37246
L3D
100K Stereo Decoder 2 T2
VR3 1 8
L4D
2
Right Output 4 5
6 J2
Schott-37246
3
L3A
JP3 JP4
4
C C
B B
A
CTD-1 Functional Block Diagram A
5 4 3 2 1
5 4 3 2 1
CTD-1 Rev. E
D D
L3A L3D
L1A L1D
L2A L2D
Jumpers shown in
VR2 -Left Level digital output position
1 2 3 4 5 6 7 8 9 10
Right Ch. Pre Emphasis JP4 ON
44 KHz
S1
B 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 B
ON ON
32 KHz 48 KHz
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
ON ON
96 KHz
44 KHz
A A
U11 R1 2 T1 NOTES:
+5V 2 1 8 TXP1
1 1. AGND & DGND TIED 1 POINT ONLY.
3 54R9 1/4W
+5V
4.7K 0805
4.7K 0805
2 PRO D
R5 R6 1 19 6
+5V C7/C3 VD+ +5V
24 7 R61 2 T2
CRE/FC1
470K 0805
TXM2 23 5 1 8 TXP2
TXM1 M2
22 C1
TXM0 M1 R32 CR2 +5V
21 .1 0805 10 54R9 1/4W C71 U16C
M0 MMBD7000
9 18 9 R62 8
V GND TXN2
10 C/SBF 11 4 5 10
11 6 RST~ .1 0805 9
14
U D D D
12 16 54R9 1/4W Schott-37246
C9/C15 VCC +5V
13 5 4 C33 3 U16A 74LS02
D +5V EM1/C8 MCK +5V EN D D
14 6 1uF 10V 1 U16D
EM0/C9 SCK
15 7 12 C21 2 11
RST~ CBL/SBC FSYNC EN
16 8 GND 8 .1 50V 74LS02 13
RST SDATA
D D 12
7
CS8404 26LS31 10uF 6.3v 10uF 6.3v
+5V D
74LS02
+5VA +5VA D
S1 D
4.7K 0805
1 20 C53 C54
2 19 C56 C57
3 18 R63 +5V J5
4 17 2 1 +5V
5 16 CKS0 4 3 .1 0805 .1 0805
6 15 CKS1 6 5 MPXL+ C59 U8 MPXR+
MPXL+ MPXR+
7 14 DFS0 8 7 .22 0805 1 28 R56
VREFL VREFR
8 13 DFS1 10 9 C60 2 27 C61 10 0805
AVSSL AVSSR
9 12 HPFE 12 11 .047 0805 3 26 .047 0805
MCLKSEL VCOM TEST
10 11 14 13 4 AINL+ AINR+ 25
16 15 MPXL- 5 24 MPXR-
MPXL- AINL- AINR- MPXR-
4.7K 0805
4.7K 0805
4.7K 0805
SW DIP-10 6 23
D CKS0 AVDD +5VA
D +5V 7 DVDD AVSS 22
R27 R28 R29 8 21 C63 C64
DVSS BVSS DFS1
C66 C67 9 20 .1 0805 10uF 6.3v U18
OVF DFS1
4.7K 0805
4.7K 0805
GND
GND
M/S~ MCLK
13 LRCK CKSI 16
14 15 C95 C96
BICK SDTO
10uF 25V C97 C98 10uF 6.3v
+5V FSYNC
2
4
AK5385A .1 0805 .1 0805
SCK
SDATA
MCLK
J4
-15V 1 2 LOUT+
3 4 FB L1A
+15V INP TXN1
MPXIN 5 6
7 8 L1D OMIT
9 10 J8-3
BNCIN1P BNCIN1P ROUT+
11 12 FB L2A
13 14 J9-3 TXN2
BNCIN2P 15 16 BNCIN2P L2D OMIT
17 18 J8-M1F2
C99 BNCIN1N BNCIN1N LOUT-
19 20 FB L3A
21 22 J8-M2F1 TXP1
+5V BNCIN2N J9-M1F2
23 24 L3D OMIT
+5V .1 0805 25 26 BNCIN2N
+5V D
U10 27 28 J9-M2F1
24MHZ ROUT-
4 3 FB L4A
VCC OSC TXP2
C70 HDR14x2
14
16
.1 0805 U12A 8 L4D OMIT
+5V D
C20 4 S GND VCC
.1 0805 2 1 1 R Q 5 3 I3A YA 7
GND OE D
4 I2A YB 9 +15V
+5V U16B +15V
D 24.576MHZ 2 D Q 6 5 I1A
U12B 5 3 6 MUX
I0A -15V -15V
10 S 4 13 2 CKS0
+5V I3B S1
U17 13 R 74F74 CKS1
Q 9 6 12 I2B S0 14
+5V +5V
11MHZ
7
Title: \\Main\e\cadence\CTD-1RE.DSN
Date: 2/15/2005 Time : 01:40:10 PM
47K 1% MF 0805
68pF 0805 C44 C45 .1 0805 JP1
150 0805 R51 .0068 0805 .0068 0805 RIGHT JMP2
CR1 C47
ROUT-
820K 0805
MMBZ5242B .1 0805 R50 C51 22uF 25V R37 10uF 25V
4
27K 0805 .047 0805 VR2 C85 10.0K 1% MF 0805
C86 C87 MPXR-
2 NE5532AD8
-
1
10K 22uF 25V 3 + R46
VREF
U7A 22uF 25V 22uF 25V R47 27R 1210
10.0K 1% MF 0805
C46
8
C49 .1 0805 R49
C50 10.0K 1% MF 0805
+15V
10uF 25V
200pF MICA 1210
6 NE5532AD8
-
7
VREF 5 +
U7B
C102
4
VR3 C89 10.0K 1% MF 0805
C90 C91 MPXL-
2 NE5532AD8
-
1
10K 22uF 25V 3 + R58
VREF
U9A 22uF 25V 22uF 25V R59 27R 1210
C65 10.0K 1% MF 0805
8
C68 .1 0805 R60
C69 10.0K 1% MF 0805
+15V
10uF 25V
200pF MICA 1210
6 NE5532AD8
-
+5V 7
VREF 5 +
U9B
R86
200K 0805
VREF
R87
U19 OMIT C93 C94
LM385M3-2.5 10uF 25V .1 0805 Broadcast Devices, Inc.
Title
CTD-1 MPX DECODER ANALOG L-R OUT / A-D
Title: \\Main\e\cadence\CTD-1RE.DSN