PROTON MODEL 520
STEREO AMPLIFIER
CONTENTS
SPECIFICATION.
ALIGNMENT.
BLOCK DIAGRAM.
WIRING DIAGRAM.
CIRCUIT DIAGRAM.
PCB PARTS LOCATION (TOP VIEW).
PCB PARTS LOCATION (BOTTOM VIEW)
ELECTRICAL PARTS LIST.
MECHANICAL PARTS LIST. 12
ASSEMBLY DIAGRAM, -13
PACKING DIAGRAM. 14SPECIFICATION
Continuous RMS Power Output per Channel
at 8 OHM 20-20kitz:
T.H.D. at Rated Power 20W:
I.M.D, at Rated Power 200:
Clipping Power at 8 OHM/4 OHM/2 Oni:
Dynamic Power at 8 OHY/4 OHM/2 OHM:
Damping Factor:
Frequency Response 20-20kii
Power Bandwidth at T.H.D. 1%:
High Level Input Resistance/Capacitance:
Line Input Sensitivity (video) :
(Tape Play):
(Phono MM) +
(Phono MC High/Low) +
Residual Noise (flat!
Channel Crosstalk (1kit2) :
Function Crosstalk (1kit2):
S/N Ratio (Unweighted) (DAD) :
(rape Play)
(Phono MM) :
(Phono MC):
Bass Control @ 1002 (Boost/cut) :
Trable Control @ 10kiiz (Boost/cut) :
spass BQ @ 75Hz:
Loudness @ -30aB (10082):
(ok) +
Phono Input Resistance (MM/MC) :
Phono Input Capacitance (Selectable) :
Phono Overload @ T.H.D. 18 mH
(202 /ktt2 20k:
Phono T.H.D. at 4.5V Output (MM) :
(ve):
Riaa Response Accuracy MM/MC:
‘vor UK Only Bass BQ Button is
Replaced by Infrasonic Filter
urn Over Freauency:
Slope:
20"
0.0158
0.0158
27w/36H1/40"
52W/80W/1008
90
40.248
10-6 0kitz
40K O8M/220pF
150nv
150nv
2.5m
0.2/0.1
O.anv
soaB
soap
soa,
9045
soap
sap
+9/-9a8
+9/-94B
+308
+6aB
+348
47% OBM/100 OM
100pe/200pP/320pF
26mv/280nv/2,80
o.o1s
0.038
+4$-0.245/4-0.545
20H
12aB/oct,ALIGNMENT
IDLE CURRENT ALIGNMENT
1. Set the volume control at minimum position.
2. Push on POWER for 5 minutes preheating.
3. Remove the load from speaker terminals.
4. Connect DC millivolt-meter across R665 for left channel and
R666 for right channel. The meter sensitivity should be set _
at 100mV full scale deflection.
5. Insert 560 OHM carbon resistor to Rxl (left channel) and Rx2
(cight channel) paralled with R657(left channel) and R65@
(right channel).
6. After insert 560 OHM, if the reading from meter is between
25mv and SOmV, the alignment is completed.
7. If the reading were less than 25nV. The value of Rxl or Rx2
should be reduced till the reading is between 25nv and 50mv.
8. If the reading were more than 50mV. The value of Rxl or Rx2
should be increase till the reading is between 25mV and 5Omv.
9. Finally , short the R665(left channel) and the R666 (right
channel) 1 OHM resistors.
DC OFF-SET ALIGNMENT
1, Set the volume control at minimum position.
2. Push on POWER for 5 minutes pre-hearting.
3. Connect a DC millvolt-meter to speaker terminals of each
channel. The meter sensitivity should be set at 100mv full
scale deflection. The positive input of the meter should be
connected to the red (+) speaker terminal.
4. Adjust VR5(Left channel) and VR6(right channel) till the
meter reading is zero.BLOCK DIAGRAMWIRING DIAGRAMWVHYDVIC LINDHID(M3IA dOL) NOILVOO1 SLYWd dod(M3IA WOLLOS) NOILV901 SLYVd 8dELECTRICAL PARTS LIST
a
[essere
8
a
eebssayaa
GuGeeeegaae
R
i
RESE
geed
Bias
Bs
GGRRReeeeeeesegeeee
SEEERERRRER EE
SESRRREEE
RRRRR TREE
gaaeegkvageed
SEQGREGSERSRRETE
aa
ae| |eteene [isms [lems Gane oor con
| [esse [arse [mmo aa or ca
| [eemem [roms [tema ‘ce ser oan tenons west
| [esrse: | ietemnc [atom oy ger same
caress | inser sesaee
carci | inane congo
j [esvons | emer coe
| coezs-c690 | a7-srrioe 507-9508
| fessvars | rearee ono
| [ese | mena eoraoe
| [serene | seer eon
cascone |inanenr eoges
cone ooo
te ements eee ng ot a ate en tor SegTaseine Sty Si BenWVYSVIG ATSWassyPACKING DIAGRAM
@ sms 8)PROTON
FULET ELECTRONIC
INDUSTRIAL CO, LTD,
68; Seo.1, San Ming Fd.
Panchiao, Taipel Hsien,
Taiwan, RO.
Tel ; (02]9625195-40
TTelox: $1903 FULETCO
PROTON CORPORATION
737 West Artesia Blvd
‘Compton CA. 90220
USA
Tol: (213) 696-5151
Telex: 02340652344
-ROTON INTERNATIONAL
376 Marlborough Street
Boston, MA. 02115
USA.
Tol: (617) 596-1011
Telex: (0254) 7108260495,
DIALCOM SVR
Printed in Taiwan