Professional Documents
Culture Documents
CAUTIONS
1. Please read this service manual carefully and make sure all elements of anti-static are in place before the
repair work is carried out.
2. Servicing and alignment MUST be undertaken by qualified personnel only.
3. Please use specified tools and equipments for servicing, in which the parameters need to be calibrated with
specified criteria.
ATTENTION
Boards, which contain Electrostatic Sensitive Device(ESD), art indicated. Following information is
ESD handling:
- Service personnel should ground themselves by using a wrist strap when exchange system
boards.
- When repairs are made to a system board, they should spread the floor with anti-static mat which is also grounded.
- Keep sensitive parts in these protective packages until these are used.
- When returning system boards or parts like EEPROM to the factory, use the protective packages as described
Content
1. Brief Introduction….………………………………………………………………………………….3
2. Exploded View……………………………………………………………………………………….4
3. Tools………………………………………………………………………………………………….5
Disassembly................…………………………………………………………………………...6-8
Assembly…………………………………………………………………………………………9-11
Specifications:
Network: 850/900/1800/1900MHz
Display: 2.4 QVGA 240*320
Camera: 0.3Mega
Talk time: 600 min
Stand-by: 240 hour
Lithium Battery: Standard (900mAh)
USB Data cable: USB 1.1
Customer Service Service Manual
Chapter 3 Tools
Tweezers Screw
Driver
Cable
Wrist
grounding
strap
Pick Antistatic
gloves
PC, Download cable Others
5
Customer Service Service Manual
3. Prize up the back cover by pick 4. Stick protection film for LCM.
5. Stick protection film for front cover. 6. Take out the PCBA by pick.
Finished.
6
Customer Service Service Manual
2. Assembly Process
3. Tear down the protection film. 4. Install the rear cover module.
Finished.
7
Customer Service Service Manual
Camera
connector
5.2 Side B
PCBA (Side B) Location of Components Side B
U705 BT IC
J301
MT6622
T-flash connector
U801 TV
MT5193
U101
CPU
X203
26MHZ
J201 battery J502、J503 U502 RF
PA IC J301 I/O
conector SIM connector
RF7176 connector
8
Customer Service Service Manual
9
Customer Service Service Manual
ATV
NMI601
MT6250
10
Customer Service Service Manual
MT6250 is a GSM/GPRS handset chip solution which integrates RF, analog baseband, digital
baseband as well as Power Management Unit(PMU) and can greatly reduce the component count
and make a smaller PCB size MT6250 including Bluetooth and FM. Besides,MT6250 is capable of
Single Antenna Interference Cancellation (SAIC) and AMR speechTMBased on a 32-bit ARM7EJ-S
RISC
Processor,MT6250 provides an unprecedented platform with high quality modem performance.
11
Customer Service Service Manual
MT6250
Audio circuit
CAMERA Data
transportation
Keypad control side
connector circuit
BT Data
transportation
Data
control side
transportation
circuit
12
Customer Service Service Manual
Clock signal
transportation side
32.768 khz Clock
crystal
MT6250
13
Customer Service Service Manual
MT6250
14
Customer Service Service Manual
Positive
pole
Temperature
detection
15
Customer Service Service Manual
Charging input
Data download
The RF7176 simplifies the phone design by eliminating the need for the complicated control
loop, harmonic filters, and TX/RX switch along with their associated matching components. The
power control loop can be driven directly from the DAC output in the baseband circuit. The
module has two RX ports for GSM850/EGSM900 and DCS1800/PCS1900. To control the mode of
operation, there are three logic control signals. TX Enable, Gpctrl1. The RF7176 offers high
efficiency at the rated pout as backed-off efficiency is improved in this TXM.
16
Customer Service Service Manual
Start frequency
Power input
antennal
RF DC
RF7176
Signal AC
17
Customer Service Service Manual
SIM 1 Data
SIM 1 reset
18
Customer Service Service Manual
System Overview
The Media Tek MT5193 is a single chip universal analog television/FM receiver that
integrates VHF/UHF full-band RF tuner, alignment-free multistandard TV/FM demodulator, audio
processor, video processor, scalar/rotation functions, and power regulators. It is low power and
high sensitivity device optimized for mobile applications such as handset, PDA, notebook, PMP,
and other portable devices.
19
Customer Service Service Manual
7.7 ATV
Power supply
TV signal output
20
Customer Service Service Manual
Can’t Download
Cannot download
OK NO
YES
NO
NO
Check VCORE、VDD、
VADD、VTCXO、VRTC、
VMEM、26MHZ、
21
Customer Service Service Manual
Upgrade the
NO
Check and NO
replace the I/O
connector Check the power manage
supply output:
VCCRE 1.8V
NO
VDD 2.8V
NO
AVDD 2.8V Replace or
VTCXO 2.8V Re-weld CPU
VMEM 2.8V
VRTC 1.2V
YES
YES
26MHZ Check and
YES replace system
clock:26MHz
NO
Replace or re-weld NO
NO
Replace U101
MT6250
END
22
Customer Service Service Manual
YES
Check and
NO
replace I/O
Check the power manage
supply output:
VCCRE 1.8V
NO VDD 2.8V Replace or
AVDD 2.8V Re-weld
VTCXO 2.8V CPU
VMEM 2.8V
VRTC 1.2V
YES
YES
26MHZ
YES Check and replace
system clock:
26MHz
NO NO
Replace or re-weld
NO
Replace U101
MT6250
END
23
Customer Service Service Manual
touch
YES replace RF
method to NO
Check if the capacitance, NO PA, Audio
varistor, LDO tube leakage check and
PA,
YES replace the
NO heat spare
Check and replace , CPU
parts
YES
YES YES
END
24
Customer Service Service Manual
Phone dead
NO
YES
Check the keypad if stuck or YES Check and reinstall the keypad
touch panel do not work to
or replace the touch panel.
make the phone “dead”?
YES
Check the CPU if is rosin U101 Re-weld or replace U101.
joint or damage?
END
25
Customer Service Service Manual
No display or display
abnormality after power on
NO
YES
YES
Change LCD FPC Problem solve
NO
NO
Change or re-solder
U101 MT6250
26
Customer Service Service Manual
Single key can’t All key can’t Some of key can’t work
work work (e.g: 1/2/3, regular problem)
NO
NO
Re-solder or
change CPU
U101 MT6250
27
Customer Service Service Manual
YES
YES
Upgrade software Problem solve
NO
NO
Use external power (2.8V) to
Change LED
check LED can work or not
YES
Problem solve
28
Customer Service Service Manual
Insert SIM
NO Clean or replace
Check if all the
SIM pins are clean SIM connector.
YES NO OK
YES Resolved
If SIM card
Replace SIM card
is available
NO
NO
MT6250 may be
defective YES
Resolder or replace
CPU MT6250
END
29
Customer Service Service Manual
No or weak signal
NO
NO
NO
Replace X801/26M
oscillator to check if
the problem is solved. OK
Resolder or replace
CPU MT6250
END
30
Customer Service Service Manual
No sound or noise
YES
YES NO
YES
Set the phone as The phone is in
Replace speaker.
normal mode Silent mode.
NO
YES
Check if the volume
Turn up the volume.
is in lowest mode.
NO
NO
31
Customer Service Service Manual
Receiver is low.
NO
Set the phone as Check if LS402
handsfree mode is damaged.
YES NO YES
YES
NO
Replace CPU
U101 MT6250
END
32
Customer Service Service Manual
Check if there’s No
Install the MIC cover
MIC cover
Yes
NO
NO
NO
Resolder or replace
CPU U101 MT6250
END
33
Customer Service Service Manual
YES
YES
Replace YES
NO or
Check charge protective tube
U200 be normal. re-solder
YES
Replace or re-solder
CPU U101 MT6250
YES
Resolved
34
Customer Service Service Manual
No charge
YES
YES
YES
Replace
Check charge protective tube be or
normal. re-solder
it
YES
YES
Resolved
35
Customer Service Service Manual
If recognize “charger
connected” NO
YES
There is no symbol
shows charging
Re-solder
Power on and connect charger, or replace
YES
input *#84666*# to check if I/O
ADC is around 0.40A connector
NO
NO
YES YES
YES
Resolved
36
Customer Service Service Manual
NO
YES
YES
NO
Replace
CPU
YES
Defective resolved
37
Customer Service Service Manual
Can’t read
T-Flash card
NO
Re-solder NO Measure if
T-flash slot T-Flash slot pin 4
VMC was 2.8V.
YES
NO YES
NO
Re-solder or
replace CPU
MT6250
38
Customer Service Service Manual
Can’t successfully
take pictures.
NO
NO
NO
Re-solder or Replace
CPU U101 MT6250
39
Customer Service Service Manual
YES
YES
Upgrade SW to check if SW upgrade
problem can be fixed?
NO
Check if there is 2.8v Voltage Replace power manage
input on C807、C808? IC
YES
YES
YES
END
40
Customer Service Service Manual
2. Echo Loop: Receiver shall produce sound when blowing over the mic.
3. Keypad: Press every button on the handset until the screen is clear.
10. Camera: Menu- Camera, test the capture and shooting, no need to save.
50