Professional Documents
Culture Documents
Con Adno ZXMSG 5200 Multiplex Service Ga
Con Adno ZXMSG 5200 Multiplex Service Ga
Con Adno ZXMSG 5200 Multiplex Service Ga
Con adno
ZXMSG 5200
Multiplex Service Gateway
Configuration Manual
Version: V3.2
Using SIP Protocol
1. Modify License
Before begin the integration, first we have to modify the license.dat;
1.1. Upload the license.dat to your laptop
Open telnet from command prompt;
ZXAN#dir cfg
Directory of flash:/cfg
attribute size date time name
1 drwx 16384 APR-17-2013 16:50:20 .
2 drwx 16384 JAN-01-1970 00:00:00 ..
3 -rwx 4096 APR-17-2013 13:50:12 nvram.dat
4 -rwx 900 NOV-08-2012 14:37:56 license.dat
5 -rwx 5426 APR-17-2013 16:50:20 startrun.dat
ZXAN#con t
ZXAN(config)# interface mng1
ZXAN(config-if)# boot-server 136.1.1.1 ------- base on clien IP
ZXAN(config-if)# boot-user zte
ZXAN(config-if)# boot-password zte
Con t
1.2. Open WFTP, set username and password by zte and set Home directory as well
ZXAN#upload license.dat
co
3. Configuration
3.1. Configuring a Rack
ZXAN#configure terminal
Enter configuration commands, one per line.
End with CTRL/Z.ctr
ZXAN(config)#
Configure the control rack.
ZXAN(config)#add-rack rackno 1 racktype MSAG
Configing the card based on the modules are installed on the shelf
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 1 POWER
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 3 GELCA
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 4 GELCA
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 5 GELCA
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 6 GELCA
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 7 GPNI
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 8 GPNI
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 16 TSLCE
ZXAN(config)# add-card rackno 1 shelfno 1 slotno 17 POWER
digitmap legend:
S = bisa habis sebelum S atau nambah di belakang S
[2-9] = bisa diisi dari 2 sampai 9
X = diisi angka 0-9
E = diisi *
F = diisi #
. = bisa diisi brpa aja bisa banyak digit
Use the ip route command to set default gateway, if the NM server and ZXMSG 5200 are not in
the same network segment.
Sho ip route
ZXAN(config)# ip route 172.28.53.0 255.255.255.192 172.24.79.1 nda usah di urus
ZXAN(config)# ip route 172.28.1.0 255.255.255.192 172.24.112.1
Muncul fail , itu krn komunikasiantara kita dan sentral blm di Creat..
WRITE..
ZXAN(config)#interface adsl_1/3-6/1-32
ZXAN(config-if)# atm pvc 1 vpi 8 vci 88
ZXAN(config-if)# pvc 1 enable
ZXAN(config-if)# pvc 2 enable
ZXAN(config-if)# pvc 3 enable
ZXAN(config-if)# switchport mode hybrid pvc 1
ZXAN(config-if)# switchport default vlan 111 pvc 1
ZXAN(config-if)# switchport vlan 110 untag pvc 1
ZXAN(config-if)# switchport mode hybrid pvc 2
ZXAN(config-if)# switchport default vlan 3136 pvc 2
ZXAN(config-if)# port-location format dsl-forum pvc 1
ZXAN(config-if)# port-location format dsl-forum pvc 2
ZXAN(config-if)# pppoe-plus enable pvc 2
ZXAN(config-if)# igmp version v2 pvc 1
ZXAN(config-if)# adsl profile DEF1M.PRF
[ROS10]: callwaitno180=0
Scenario; B with three party feature, B calling A, A on hold now and B calling C
B press “FLASH+3+#”, A and B and C join conference.
Make sure that digitmap for 3# is available. Note: # to be symbolized by F
ZXAN#sho msag digitmap
digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85
xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]
x|04[2-9]xxxxxSxxx|85xxxxx
3.13.4. HotLine
HotLine services, both immediate and delay, parameter change under 9999 port.
Execute command:HotLineServCode
[ROS10]:HotLineServCode
HotLineServCode = 0x216b568: value = 0 = 0x0 (blue color show hot line service code)
Display service code by execute command: d 0x216b568
[ROS10]:d 0x216b568
0216b560: 0000 0000 0000 0000 * ......*
0216b570: 0000 0000 0000 0000 0000 0000 0000 0000 *................*
0216b580: 0000 0000 0000 0000 0000 0000 0000 0000 *................*
0216b590: 0000 0000 0000 000b 0000 0001 0000 0000 *................*
0216b5a0: 0000 0000 0000 0005 5a54 4500 0000 0000 *........ZTE.....*
0216b5b0: 0000 0000 0000 0000 0000 0000 0000 0001 *................*
………………………………………..
value = 21 = 0x15
[ROS10]:m 0x216b568
It will output '0000-...',then type 0302(No display,just input),
0216b568: 0000-0302
The'0000-' will display again,and then type 0100,
0216b56a: 0000-0100
Input .(dot) after display '0000-'.
0216b56c: 0000-.
After all the modify, it will show;
value = 1 = 0x1
3.13.5. Abbreviated
For abbreviated feature, make sure the digitmat for abbreviate is available. For example by
dialing “**03” will connecting to specified number, so the digitmap format will be “EE03”.
Note: * to be symbolized by E.
ZXAN#sho msag digitmap
digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85
xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]
x|04[2-9]xxxxxSxxx|85xxxxx
3.13.6. Keyboard
Keyword feature depends on digitmat format. The form for keyword feature is
*34*password*class#
Scenario: A dial *34*1234*1#. So the password is “1234” and class is “1”
Note; Class (0=block all, 1=local only, 2=interlocal, 3=international call)
ZXAN#sho msag digitmap
digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85
xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]
x|04[2-9]xxxxxSxxx|85xxxxx
3.13.7. Fax
Both Huawei and Ericsson IMS do not support T38 and VBD for Fax service, disable fax
priority 1 and fax priority 2
ZXAN(config-msag)# mg capability 1 fax-pri1 0
ZXAN(config-msag)# mg capability 1 fax-pri2 0
3.13.8. EDC
For EDC just make sure the digitmap is available. For example, B*A EDC server number
usually depend on 13 digits. So the digitmap consists of 13 digits.
ZXAN#sho msag digitmap
digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85
xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]
x|04[2-9]xxxxxSxxx|85xxxxx