Professional Documents
Culture Documents
5 April 1979
Contents
1 SCOPE
This EURONORM applies to unalloyed' mild steel flat This EURONORM applies to sheet, coils (minimum
products in commercial quality, bending and profiling width 600 mm), slit coils and cut lengths from sheet or slit
quality, and drawing qualities produced by a continuous coil. It does not apply to general structural steel sheet and
hot-dip zinc coating process. The thickness of the pro- coil (see EURONORM 148 — in preparation). Qualities
duct supplied shall be the finished thickness after coating. for hot-dip zinc coated unalloyed mild steel sheet and coil
for cold forming are given in EURONORM 142.
2 GENERAL DEFINITIONS
For the purposes of this EURONORM, the following A slit coil is a flat product wound in regularly superim-
definitions apply: posed laps, obtained by slitting a coil. The product may be
subdivided into two categories according to whether or
not its width is less than 600 mm.
A sheet is a rectangular flat product not less than 600 mm
in width obtained by cutting up a coil or a slit coil. A cut length is a rectangular flat product less than
600 mm in width, obtained by cutting up a slit coil or a
sheet.
A coil is a flat product not less than 600 mm in width,
wound in regularly superimposed laps after the final pro- Note: The corresponding terms in French, German,
cessing operation. English, Dutch and Italian are given in Annex A.
3 MEASUREMENT
The tole rance on flatne ss is the maximum pe rmitte d dis The e dge cambe r is the late ral de parture of the e dge of the
tance be twe e n the she e t and the flat horizontal surface on material from a straight line , forming a chord.
which it is place d.
The e dge cambe r shall be me asure d on the concave e dge .
3.5 Out of squaren ess The me asuring base shall be a distance of 2 m, taken any
where along the e dge .
The out of square ne ss value 'u' is the orthogonal pro
jection of a transve rse e dge on a longitudinal e dge (se e If the she e t or cut le ngth is less than 2 m long, the me asur
Fig. 1). ing base shall be the ir le ngth.
4 SHEET
Unless othe rwise state d at the time of orde ring, she e t shall be de live re d with normal tole rance s.
The tolerance on flatness shall be as given in the following The out of squareness value 'u' shall not exceed 1% of the
table: actual width of the sheet.
Unless otherwise stated at the time of ordering, the product shall be delivered with normal tolerances.
The tolerances on thickness shall be the same as for sheet If sheets, cut from coil by the customer, are required to
(see Table 1) except in the region of the welds, where they have special flatness characteristics, or if coils are used
are doubled over a length to be determined by special directly for a special purpose, an agreement on tolerances
agreement at the time of ordering. will have to be reached between manufacturer and pur
chaser.
Special tolerances do not apply to Fe Ρ 01 G quality.
The agreed flatness tolerances will only be obtained if the
purchaser carries out adequate flattening, while shearing.
5.2 Tolerances on width
The width tolerances shall be the same as those specified 5.4 Tolerances on edge camber
for sheet (4.3).
The edge camber tolerances shall not exceed 6 mm over a
Special tolerances are obtained by reshearing of the edges. length of 2 m (see 3.6).
Unless otherwise stated at the time of ordering, the product shall be delivered with normal tolerances.
6.1 Tolerances on thickness the region of the welds, the tolerances shall be doubled
over a length to be agreed at the time of ordering.
These shall be identical to those specified for sheet and
coil having widths 1 200 mm or below (see Table 1). In Special tolerances do not apply to Fe Ρ 01 G quality.
Page 4
The tolerances on width shall be as follows: Note: Wide tolerances apply in the case of cut lengths
obtained by reshearing of sheets.
Table 1
s 1 200 > 1 200 s 1 500 > 1 500 s 1 200 > 1 200 s 1 500 > 1 500
Notes
1. For coils or slit coils, these tolerance values refer to the whole length, except in the region of the weld where the values are doubled {see 5.1 and 6.1).
2. For grade Fc Ρ 01 normal tolerances shall be increased by ± 0.01 mm unless otherwise agreed between the manufacturer and purchaser. Special tolerances do not apply to this
grade.
3. Coil may be supplied without welds by agreement between the manufacturer and purchaser.
4. For coatings of types Ζ 450 and Ζ 600, these tolerance values shall be increased by 0.02 mm.
Page 5
ANNEXA
Terminology used in this EURONORM
Large bande refendue Längsgeteiltes Band Slit coil Gesneden breedband Nastro largo cesoiato o
(Spaltband) aus Breit- nastro cesioato
band
Barre (à partir de large Stab (aus Spaltband Cut length (from slit Plaatstrook (uit gesne- Bandella (da nastro
bande refendue ou de oder Blech) coil or sheet) den breedband of plaat) cesioato o da lamiera)
tôle)
BFR 80 DKR 14 DM 5 FF 11,30 LIT 2 200 HFL 5,50 UKL 1.30 USD 2.60