Professional Documents
Culture Documents
Features Description
• Switch mode controller for single switch LED drivers HV9910B is an open loop, current mode control, LED
• Enhanced drop-in replacement to the HV9910 driver IC. This IC can be programmed to operate in
• Open loop peak current controller either a constant frequency or constant off-time mode.
• Internal 8.0 to 450V linear regulator It includes an 8.0 - 450V linear regulator which allows it
• Constant frequency or constant off-time operation to work from a wide range of input voltages without the
need for an external low voltage supply. HV9910B
• Linear and PWM dimming capability
includes a PWM-dimming input that can accept an
• Requires few external components for operation external control signal with a duty ratio of 0 - 100% and
a frequency of up to a few kilohertz. It also includes a 0
Applications - 250mV linear dimming input which can be used for lin-
ear dimming of the LED current.
• DC/DC or AC/DC LED driver applications
• RGB backlighting LED driver HV9910B is ideally suited for buck LED drivers. Since
• Back lighting of flat panel displays the HV9910B operates in open loop current mode con-
• General purpose constant current source trol, the controller achieves good output current regula-
• Signage and decorative LED lighting tion without the need for any loop compensation. PWM
dimming response is limited only by the rate of rise and
• Chargers
fall of the inductor current, enabling very fast rise and
fall times. HV9910B requires only three external com-
ponents, apart from the power stage, to produce a con-
trolled LED current. This makes HV9910B an ideal
solution for low cost LED drivers.
VIN 1 16 NC
NC 2 15 NC
NC 3 14 RT
CS 4 13 LD
CS 2 7 LD NC 6 11 NC
GND 3 6 VDD NC 7 10 NC
CIN
CO
D1
CDD L1
VIN
VDD
HV9910B
LD GATE Q1
PWMD CS
RT GND
RCS
RT
Input
Input DC supply voltage 3
VINDC 8.0 - 450 V DC input voltage
range2
Shut-down mode supply 3
IINSD - 0.5 1.0 mA Pin PWMD to GND
current
Internal Regulator
VIN = 8.0V, IDD(ext) = 0, 500pF
VDD Internally regulated voltage - 7.25 7.5 7.75 V at GATE; RT = 226kΩ, PWMD
= VDD
VIN = 8.0 - 450V, IDD(ext) = 0,
∆VDD, line Line regulation of VDD - 0 - 1.0 V 500pF at GATE; RT = 226kΩ,
PWMD = VDD
IDD(ext) = 0 - 1.0mA, 500pF at
∆VDD, load Load regulation of VDD - 0 - 100 mV GATE; RT = 226kΩ, PWMD =
VDD
VDD undervoltage lockout 3
UVLO 6.45 6.7 6.95 V VDD rising
threshold
VDD undervoltage lockout
∆UVLO - - 500 - mV VDD falling
hysteresis
Current that the regulator
4
IIN,MAX can supply before IC goes 5.0 - - mA VIN = 8.0V
into UVLO
PWM Dimming
3
VEN(lo) Pin PWMD input low voltage - - 0.8 V VIN = 8.0 - 450V
VEN(hi) Pin PWMD input high voltage 3 2.0 - - V VIN = 8.0 - 450V
Pin PWMD pull-down resis-
REN - 50 100 150 kΩ VPWMD = 5.0V
tance at PWMD
POR
LD -
+
CS Blanking R Q GATE
+
250mV - S
Oscillator
GND RT PWMD
XXXXXXXX HV9910B
XX e3 YYWW LG e3 1447
NNN 343
XXXXXXXXXXX HV9910BNG
XXXXXXXXX e3 1447343 e3
YYWWNNN
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for product code or customer-specific information. Package may or
not include the corporate logo.
Note: For the most current package drawings, see the Microchip Packaging Specification at www.microchip.com/packaging.
Note 1 E1 E
(Index Area L2 Gauge
D/2 x E1/2) Plane
1 L Seating
L1 θ Plane
A A2 Note 1
Seating h
Plane
e b
A1
Side View A View A-A
Note: For the most current package drawings, see the Microchip Packaging Specification at www.microchip.com/packaging.
Note:
1. 7KLVFKDPIHUIHDWXUHLVRSWLRQDO,ILWLVQRWSUHVHQWWKHQD3LQLGHQWL¿HUPXVWEHORFDWHGLQWKHLQGH[DUHDLQGLFDWHG7KH3LQLGHQWL¿HUFDQEH
DPROGHGPDUNLGHQWL¿HUDQHPEHGGHGPHWDOPDUNHURUDSULQWHGLQGLFDWRU
Symbol A A1 A2 b D E E1 e h L L1 L2 ș ș
MIN 1.35* 0.10 1.25 0.31 9.80* 5.80* 3.80* 0.25 0.40 0O 5O
Dimension 1.27 1.04 0.25
NOM - - - - 9.90 6.00 3.90 - - - -
(mm) BSC REF BSC
MAX 1.75 0.25 1.65* 0.51 10.00* 6.20* 4.00* 0.50 1.27 8O 15O
JEDEC Registration MS-012, Variation AC, Issue E, Sept. 2005.
7KLVGLPHQVLRQLVQRWVSHFL¿HGLQWKH-('(&GUDZLQJ
Drawings are not to scale.
Note: For Media Types M901 and M934, the base quantity for tape and reel was stan-
dardized to 2600/reel. Both options will result in delivery of the same number of
parts/reel.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
QUALITY MANAGEMENT SYSTEM Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
CERTIFIED BY DNV Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
== ISO/TS 16949 == devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.