Professional Documents
Culture Documents
MOHAMMED AIJAZ
Email : mdaijazec@gmail.com
Tel : 0091 8096082009
OBJECTIVE
To seek a challenging, responsible position in the field of Construction Industry, where I can
apply my technical and analytical skills efficiently.
EXECUTIVE SUMMARY
About 8+ years of experience in Planning, Managing, Executing,Construction
Projects.
Organize, implement, conduct and manage the QA/QC Programs as per the
Company's Quality Policy.
Checking, submitting and approving the Hold Points.
Conduct inspection in sites as per the submitted RFI’s.
Raise the NCR and CAR against any incompliance to the contract specification.
Coordinate all inspections; monitor the required tests and record inspections and
tests made as per the Contract Plan and Contract Specifications.
Coordinate with the Project Manager regarding work performance and hold
authority to stop work in any area where discrepancies remain uncorrected and/or
cancel the stop work order upon satisfactory correction of noted deficiencies.
Provide technical support to the Project Manager and guidance to site staff in
submission of materials for approval, request for inspection, shop drawings.
Assist QA/QC Manager in conducting internal quality audits.
Ensure that Non-Conformance Report (NCR) is raised once the activities deviated
from the Contract Specifications or normal construction industry practices.
Coordinate with the project staff to compile and maintain pertinent records of
inspection and testing until end of the contract and all pertinent records.
Team Leading and Conducting Regular meetings to avoid gaps and ensure timely
completion of project.
Attend Monthly Project Review Meetings (PRM) and alert the project team of any
potential problems.
Good at handling team and planning in advance to meet the Target timelines.
Team Leading and Conducting Regular meetings to avoid gaps and ensure timely
completion of project.
Tracking and reporting the Site progress for all areas weekly & Monthly
EDUCATION
B.E – ( Electronics and Communication Engineer ]
TECHNICAL SUMMARY
Area of Excellence
WORK EXPERIENCE
WORKED AT : Gentech Automation Limited as a QA/QC Senior Engineer. (Sep 2015 – Mar
2018)
Gentech Automation is a largest Engineering, Construction , Instrumentation
Projects.Their projects are running all over the India services to Homes and Commercial
Businesses.
Shop Drawing
Qc Excavation, trench & shoring
Materials / Equipment WORKED AT : Al Harbi Trading And
Contracting As a QC Engineer (MEP) in
Formworks / Shuttering Saudi Arabia , Jubail . (May 2013 – Aug
Scaffolding / flatform 2015)
Cleanliness & Access
Embedded Anchor Bolts Project :1 ( Royal Commission, Jubail -
Reinforcement (FBECR / Polymer 725C03)
Excavation, trench & shoring
Al Harbi Trading and Contracting,
Survey,Level & Alignment / Line
Electro -Mechanical Construction
Compaction (FDT)
Project, Irrigation water pump station,
Embedded pipes Jubail, KSA
Preparation of Construction Joint
Hold Point Ensured implementation of quality
Waterproofing / Vapor Barrier control as per Royal Commission
Verification of Rate of Placement Engineering Standards while
Provision of Hot-Weather executing electrical works; ensured
Concreting equipment and devices used comply
with Royal Commission Standards
and were tested according to standard procedures.
Ground rods and grounding cables
Main Distribution Board (MDB), Motor Control Center (MCC) panel, Lighting
Panel (LP), Power Panels (PP), Fire Alarm Control Panel (FACP), Access Control
Panel Boards and Control Panel of Package Air Conditioning Unit
Auxiliary power outlets, motor, emergency light and lighting fixtures
LV and MV switchgears; worked on pre-commissioning as well
Supervise and make sure that all terminated cables from the Primary and Secondary
side of Transformers has markers and approved by STC representatives
Transformers, HV & LV switchgear, control gear, bus-bars, panels, auto change over
switches, voltage regulators, distribution panels and their associated wiring
Conducted inspection on high & low voltage termination, splicing, and cable pulling
operations, above & below ground electrical installations, switchgears, MCC,
electrical motors, generators, transformers, panel board’s switchgears, DCS, ATS,
MTS & battery system
Implemented project quality plan including testing, and pre-commissioning activities
of electrical equipment & system such as power Control, instrument cables, fire
detection & alarm, junction boxes panels, Battery/UPS system, switchgear, MCCs
Coordinated with senior-level and project management to resolve discrepancies/check
revision of works.
Supervise the installation of low voltage panel board, switchboard, conduit fittings,
boxes receptacles, & switches.
Installation of RTU for industrial Lift Stations.
Ensure alignment with other areas of project by coordinating with structural, piping,
and instrumentation departments regarding designing and modelling issues.
Advocated for quality by implementing project quality plan for covering, testing, and
pre-commissioning activities of electrical equipment & system such as power
Control, instrument cables, fire detection & alarm, junction boxes panels,
Battery/UPS system, switchgear, MCCs.
Demonstrate strong knowledge and understanding of cables by supervising and
monitoring Advance quality by resolving on-site problems by applying approved
procedures.
WORKED AT : Kantar Operations Pvt Ltd As a Analyst ,Hyderabad India. (Mar 2011-
Sep 2012 )
Kantar Operations to provide Engineering,communication,
Automation, & development and systems integration company specializing in
Automation applications ranging from work flow automation to process control.
PERSONAL DETAILS
(Mohammed Aijaz)