Professional Documents
Culture Documents
Heatmasters Group
Heatmasters Group is selection of heat treatment companies in seven countries. The Group
has its roots in Finland and has over 35 years of experience in heat treatments, so they
understand the demands made on high performance heat treatment equipment and services.
Strong investments on heat treatment control systems with computer‐based technology and
use of GSM data transfer has made Heatmasters one of the leading suppliers of heat
treatment equipment. They design, manufacture, sell and service heat treatment equipment
and accessories. Productivity, accuracy and reliability are the key properties of our products.
Furthermore Heatmasters Group offers heat treatment services in its own workshops in seven
countries and at clients project sites. First‐class performance and accurate temperature
measurements are essential for their heat treatment works.
Heatmasters specialists serve clients on several industries, helping them to find suitable,
effective and economical solutions in heat treatment.
www.heatmasters.net
®
EN ISO 17663:2009
Tapio Finnström
HEATMASTERS SWEDEN AB
Tagenevägen 34B
425 37 Hisings Kärra
Tel +46 31 572 141
Fax +46 31 572 120
www.heatmasters.net
®
QUALITY
www.heatmasters.net
®
EN ISO17663:2009
SCOPE
This international standard provides guidance for manufacturers that perform heat
treatment or produce heat-treated products or components
This standard can also be used as a basis for assessing the manufacturer or
heat treatment company in respect to its heat treatment capability
www.heatmasters.net
®
EN ISO 17663:2009
NORMATIVE REFERENCES
www.heatmasters.net
®
EN ISO17663:2009
EN ISO 13916
Standard defines different temperatures and the measurement
(Tp) preheating temperature
(Ti) interpass temperature
(Tm) maintenance temperature
Distance of measuring point
e < 50 mm A=4 x e, min. 50 mm
e > 50 mm A = 75 mm
www.heatmasters.net
®
EN ISO17663:2009
IEC 60584-2
www.heatmasters.net
®
EN ISO17663:2009
EN 10052
www.heatmasters.net
®
EN ISO 17663:2009
SUBCONTRACTING
The manufacturer shall ensure that the subcontractor can comply with the quality
requirements the specifications
Any subcontractor shall work under the orders and responsibility of the manufacturer and
shall comply with the relevant requirements of the standard
Message of these sentences means that the company that is ordering heat treatment services
from other company must have knowledge to evaluate subcontractor
=
Know basic content of this standard
www.heatmasters.net
®
EN ISO 17663:2009
PERSONNEL
The manufacturer shall appoint a sufficient number of competent personnel for the
planning, performing and supervising of the heat‐treatment work according to specified
requirements
The competence of personnel shall be confirmed by the manufacturer
www.heatmasters.net
®
EN ISO 17663:2009
EQUIPMENT
For an evaluation of capacity and capability, the manufacturer shall maintain a list of
essential equipment used for heat treatment
The equipment shall be adequate for the application concerned.
All devices used for adjusting, measuring and recording the temperature shall be suitably
validated at specified intervals by calibrated measuring instruments.
A file shall be kept on validated equipment including the validity.
www.heatmasters.net
®
EN ISO 17663:2009
HEAT TREATMENT ACTIVITIES
Heat treatment shall, as appropriate, be carried out in furnaces
www.heatmasters.net
®
EN ISO 17663:2009
HEAT TREATMENT STAGES AND PARAMETERS
The manufacturer of the product or component is responsible for determining the heat
treatment parameters
Use of right heat
treatment parameters
has direct influence to
the result of the process
www.heatmasters.net
®
EN ISO 17663:2009
LOADING AND TIMING OF THE PROCESS
In some cases loading temperature
should be specified
www.heatmasters.net
®
EN ISO 17663:2009
HEATING RATE
Heating rate is related to
type and thickness of the
material.
The given value is
maximum heating rate
www.heatmasters.net
®
EN ISO 17663:2009
HOLDING STAGE
Holding temperature and
time is related to type
and thickness of the
material.
Value of holding
temperature is normally
given as a temperature
range
www.heatmasters.net
®
EN ISO 17663:2009
COOLING RATE & UNLOADING TEMPERATURE
Cooling rate is related to
type and thickness of the
material.
The given value is the
maximum value for
cooling rate
After unloading
temperature the product
can be cooled
uncontrolled
www.heatmasters.net
®
EN ISO 17663:2009
HOLDING TIME
Holding time starts when the temperature of all measuring points has reached
minimum value of the range of the holding temperature
Holding time stops when one
of the measuring points falls
below the minimum value of
the range of the holding
temperature
The holding time depends on the type of heat treatment, material and material
thickness
www.heatmasters.net
®
INFLUENCE TO HARDNESS
Place of the welding seam
Black diagram
Heat treatment not used
Yellow diagram
Preheating in 300 °C
Red diagram
Stress relieving done in 680 °C
www.heatmasters.net
®
www.heatmasters.net
®
www.heatmasters.net
®
EN ISO 17663:2009
MINIMUM NUMBER OF MEASURING POINTS
www.heatmasters.net
®
EN ISO 17663:2009
HEATING ZONE & INSULATION ZONE
Width of the heating
zone (A)is determined
with a formula
Du = outside diameter,
e = wall thickness
Width of the insulation heating zone (B)
is 2 x A
www.heatmasters.net
®
EN ISO17663:2009
HEATED BAND-WIDTH
L2 ≥ 2 ,5 (2D2 4 t 2)t 2
L3 ≥ 2 ,5 (2D3 4 t 3)t 3
www.heatmasters.net
®
EN ISO 17663:2009
HEAT TREATMENT RECORD
www.heatmasters.net
®
EXAMPLES
SHOULD RING YOUR BELLS
www.heatmasters.net
®
EXAMPLES
SHOULD RING YOUR BELLS
www.heatmasters.net
END OF THIS PART