ANF - ANT HGRS
Governor & Governor GearLo 6 tg aU Lea
Governor & Governor Gear
60
Outline
Poe
Page
60-01b-00 | 41
The RHD or UGB type hydraulic governor is used for this engine.
This governor is a high performance variable speed governor.
AAs the hydraulic fluid is contained in the governor, piping and sub-tank installation are unnecessary when
installing the governor on the engine. It is a very compact structure.
The governor is driven with the bevel gear that has been installed on the cam gear of the engine.
‘The following remote controller is supplied.
Type of Controller
Outline of operation
Governor Motor Controller
When the motor operates, the speed setting screw moves vertically, and
speed setting screw movement changes the set load of the speeder spring
to vary engine speed.
‘The engine speed can also be changed manually in the same way by turn-
ing the synchronizer knob.
Please refer to attach "SERVICE MANUAL GOVERNOR MODEL RHD or UG8" for the structure and opera-
tion, repair and maintenance, and adjustment of the RHD series hydraulic governor and controller.
"Scalaaiienanianonay:EY26 OPERATION MANUAL
Governor & Governor Gear No. Page
60 Overhaul of Governor Link eaten (oa
‘Adjustment on linkage of governor gear.
1) Shift the start/stop handle into the STOP setting, and adjust rack adjust screws of fuel injection pumps of all
cylinders so that these rack scales are coordinated to the graduation "8" to "9" in each ease, (At this time,
confirm that the No.1 lever can move lightly.)
Fig. 60-02-1 Governor Link (Type RHD Governor)
Star/Stop Handle
Governor No.t Lever Shaft Fuel Pump
2) Adjust the coupling bolt of the No.2 lever so that the distance between the center of the No.1 lever shaft
and the center of coupling rod becomes about 85 mm, and then connect the coupling rod to the governor
lever.
Fig. 60-02-2 Set Point of Link
\ About sSmm
Not Lever Shaft Center
3) Insert a blade screwdriver into the end of output shaft, and turn this shaft fully toward the fuel DECREASE.
side to bring the pointer to set in graduation "0"
Next, tum the output shaft toward the fuel INCREASE side by one graduation to set the pointer in gradua-
tion "1", and fix the governor lever to the output shaft by clamping the mounting bolt,
4) Confirm that there is no twist existing to the governor gear.
5) Operating the start/stop handle to the RUN position and then to the STOP position, confirm the rack scale
of each fuel injection pump.
STOP position: A position ofthe start/stop handle corresponding to a position of the injection pump where
the injection sound is not issued as the flywheel is turned.
cane,=) trol) Vale) EOL
Peery
Governor & Governor Gear No.
Overhaul of Governor Link
60-02b-00
2, [In the case of an engine equipped with Type UG-8 governor]
1) Shift the start/stop handle into the STOP setting, and adjust rack adjust screws of fuel injection pumps of all
‘cylinders so that these rack scales are coordinated to the graduation "8" to "9" in each ease, (At this time,
‘confirm that the No.1 lever can move lightly.)
Fig. 60-02-8 Governor Link (Type UG-8 Governor)
Start/Stop Handle
Governor
NO.t Lever Shaft Fuel Pump
2) Adjust the coupling bolt of the No.2 lever so that the distance between the center of the No.1 lever shaft and the
ccenter of coupling rod becomes about 115 mm, and then connect the coupling rad to the governor lever.
Fig. 60-02-4 Set Point of Link
Coupling Rod
‘About 115mm \ %
3) Insert a blade screwdriver into the end of output shaft, and tum this shaft fully toward the fuel DECREASE.
side to bring the pointer to set in graduation "0".
Next, turn the output shaft toward the fuel INCREASE side by one graduation to set the pointer in gradua-
tion "1", and fix the governor lever to the output shaft by clamping the mounting bolt.
No.1 Lever Shaft Center
4) Confirm that there is no twist existing to the governor gear.
5) Operating the start/stop handle to the RUN position and then to the STOP position, confirm the rack scale
of each fuel injection pump.
STOP position: A position of the start/stop handle corresponding to a position of the injection pump where
the injection sound is not issued as the flywheel is turned.
7 WANAEY26 OPERATION MANUAL Pee
Governor & Governor Gear No. as
60
Overhaul of Governor Gear | soosa00 | v2
1) Governor
Refer to the attached Hydraulic Governor Service Manual.
2) Governor driving gear
[Cautions for disassembly & reassembly] |
(1) Replace ball bearings of governor driving gear with the new ones by 8,000-10,000 hours of operation
{about two years) or when they are resulted in abnormal wear.
(2) When fitting the driving gear, confirm of the backlash of bevel gear, and adjust the backlash by regulating
the number of shims of the bevel gear boss part. For backlash of bevel gear, refer to Section 00-09
(3) When mounting the governor, check to see if there is not any forcing tofiting of governor shaft and spline
coupling.
Fig. 60-03-1 Type RHD Governor Driver
_- Spline Coupling
fe
eens
ts |
spacer
Circ — ~~ Adjusting Shim
Bevel Gear —
g
wanasanbEY26 OPERATION MANUAL
Governor & Governor Gear Wo.
Overhaul of Governor Gear 60-03a-00
Fig. 60-03-2 Type UG-8 Governor Driver
— Govenor
— Spline Coupling
_— Driving Shaft
vVanasanpi. et eae ee]
fn
MEANT SLUEDRERAR be
Parts List of Governor & Driving Device 60.51b-00
A: RHD S147/<+4£4#, With RHD Type Governor Spec.
RIS4 4 — 1
=
VAMAZARLhe hd eed
poe Mey tet Ue tte |
60 BEASTS SURDRERER i toes
Parts List of Governor & Driving Device 60-51b-00 213
° B : UG-8 BAi/<+4t#R, With UG-8 Type Governor Spec.
ea o @—i8
RI9174 1
OPPOSITE SIDE OF FLYWHEEL
‘F 6005 BEARING, 6005 NTN 1 1
16} 1 24101-062054 | AFUYF 6205 BEARING, 6205 NTN 1 1
16 1 26212-100602 | 9ZAS#/Lb 10x60 | STUD, BOLT 10 x 60 4
1 26206-100602 | ALF 10x60 BOLT 10 x 60 4
7} 4 26706-10002 | ty b 10 ‘NUT, 10 10 | 10
Wy 1 | 26871-14002 | SYyvttyb (RYED14 | NUT, 14 1 1
WW} 1 = | 43400-004020 | HANH RU Viva Y | GASKET, GOVERNOR 1 4%
20] 1 138603-61780 | ¢Lb—Ya vyu¥F JOINT 1
2 1 22301-060360 | F—/AEY (9) 6x36 | PIN, 6 x 36 1
22) 1 26212-100602 | YTAEALb 10x60 | STUD, BOLT 10 x 60 4
ou GaLe kd htt ch a kh a iconaera ead
No. Pe
60 maEEMAR bs
Parts List of Governor Linkage 60-52b-00 V3
wansaaana UL Ted
Pa waa ys ee
Parts List of Governor Linkage 0-52-00 | 28
A: RMD 2Hi/<+4t#R. With RHD Type Governor Spec.
B : UG-8 SAi/<+tt#R, With UG-8 Type Governor Spec.
Paleare ides ceca BRE Part Name stay | a*
X | 761695-66010 | #3979 Y9FL7S(RHD | GOV.LINKAGE, RHD Tset
x 761695-66031 | #39Y99FY9=(UG—B | GOV.LINKAGE, UG-8 set
1 1 137600-51540 | AA(FANRI LTD ‘SPRING, SHAFT 6 6
2 1 137600-51560 | Y¥F(FANLITD JOINT 6 6
3 1 135210-61090 | JO4YADFTY ‘LEAD 1 1
4 1 11695-66090 | Lvt—(FTLEARY LEVER, STOP PISTON 1 1
5 1 139964-66480 | NO 3L/<—(B LEVER, 3RD B 1 6
1 151695-66610 | NO 3L/<-(B LEVER, 3RD B 1
1 151695-66600 | NO. 2 Lvt— LEVER, 2ND 1
1 146673-66950 | NO. 2 Lt— LEVER, 2ND 1
¥ 1 151695-66700 | S477b(1 ST Lv<— | SHAFT, 1ST LEVER 1 1
8 1 153604-66760 | Jyya(1 STOVIb BUSH, 1ST LEVER SHAFT | 4 4
9 1 138613-66802 | NO 1 Lbvi— LEVER, 1ST 6 6
10 1 139653-66810 | Lvi—P FHA RETAINER, LEVER 6 6
W 1 142613-66820 | aF4 ATT PIECE, FIXING 6 6
12 1 142822-66830 | s<* ‘SPRING 6 6
13, 1 151695-66830 | AVL KC SY FLAS | BOLT, RACK ADJUST 6 6
14 1 138613-66840 | FAVE AY ‘SCREW, ADJUSTING 1 1
15, 1 142613-66841 | AFAKAD— COLLAR, THRUST 8 8
16 1 151695-66850 | FF ASYVAE-Z PIECE, DISTANCE 6 6
7 1 151604-66860 | Y9O7/NKA(1 ST LS HOUSING, BEARING 1 1
18 1 151695-66880 | Y994744(1 STL ‘STAND, LEVER BEARING | 3 3
19 1 138613-66920 | si ‘SPRING 1 1
20] 2 x 18613-66160 | AO ‘SPRING SHOE 1 1
a 2 x 137600-66830 | 2¥9 (SP HOOK, SPRING 1 1
22 1 22137-220000 | #A#(SH* 22 WASHER, = 22, 6 6
23. 1 22212-060000 | W*% FHA 6 WASHER, 6 6 6
24) 1 22312-060300 | A¢aNED 6X30 | PIN, 6X 30 6 6
ny60 BaEESAR
Parts List of Governor Linkage 60-52b-00 33
Mo [ton | tar | Part to. saen Part Hane | ROW | sours
3) 1 22322-050350 | F#—/KED 5X35 PIN, 5X 35 a+ 2
26) 1 22351-050035 | AFYYFXY 460A X35) PIN, 5.0AX 36 15 | 15
a} i 22451-10100 | yey 1.0X 100 | WIRE, 1.0X 100 1 1
eB) 1 26206-080202 | AL b 8x 20 BOLT, 8X 20 242
2a} 1 26206-120252 as a 2x 25 BOLT, 12X 25 6 | 6
go] 4 26567-06012 | +XaaT(+776 xX 12 | SOREN, 6 X 12 6 | 6
ala 26577-040082 | #5aaH47+ 4x @ | SOREN, 4X 8 ‘fa
32] 1 26706-080002 | +b 8 NUT, 8 1 1
33] 1 26756-06002 | KAP Yb 6 NUT, 6 6 | 6
34) 1 26796-100002 | KAF Yb 10 NUT, 10 1 1
35] 1 138987-66820 APALAFES | RETAINER, THRUST 1 1
WABAZARLk dhe e ck A a eh Uc Ce
SHEN EILR BR
Parts List of Start/Stop Lever
=)
SIDE OF FLYWHEELAe Leh ee ee
eo RABY EBB a a
Parts List of Start/Stop Lever 60-53-00 | 2/2
He | owt | oa | Part ho ease Part none | Oy | as
1 1 151695-66010 FAINDEMSL BRACKET, HANDLE 1
2 1 139653-66050 | wYF4s\y K/L A CMP | HANDLE, START/STOP A | 1
3 2 x 139653-66253 | sw F4 Ny KIL HANDLE, START/STOP- 1
4 2 139653-66261 | WWYF4NYELOD SHAFT, START/STOP 1
5 2 138613-66270 | sw F4s\> KIL YF | KNOB, HANDLE 1
6 2 139653-66280 | WY F4ANY KYA CLAW, HANDLE 1
7 a x 137600-66300 | »\> KLE PIN, HANDLE 1
8 2 130140-66540 |< ‘SPRING 1
9 1 151604-66170 | Lui—¥4 Jy a BUSH, LEVER MOUNT 1
10 1 147673-66200 | Lai—bU Ie E4 MOUNT, LEVER 1
W 1 151695-66210 | A4 NUR YTTS PLATE, LABEL SETTING | 1
12 1 141616-66220 | WWYF4 IVY Eb ATS | PLATE, STOPPER 1
13 1 137600-66230 | b A 7ILb BOLT, STOPPING 2
14 1 153604-66760 | PYYaA(1 STU¥Tb BUSH, 1ST LEVER SHAFT 1
15 1 22137-06000 | ##4(S H+ 6 WASHER, = 6 3
16 1 | 22137-10000 | #7 4(5 10 WASHER, 10 2
7 1 22242-00360 | KAD C(UD 36 RING, 36 1
18 1 26116-060302 | AL b 6X 30 BOLT, 6X 30 3
19 1 26206-100402 | Lk 10X 40 BOLT, 10X 40 2
20 1 26206-120252 | #ALh 12x 25 BOLT, 12X 25 2
21 1 26716-060002 | Yb 6 NUT, 6 3
22 1 46130-00010 | 4 POAT IF ‘SWITCH, MICRO 1
23 1 151695-66930 | 2>(Q-K4447—4% | POINTER, LOAD INDICA. 1
4 1 22212-08000 | WA FHA 8 WASHER, = 8 1
6 1 26206-080102 | AL 8x 10 BOLT, 8X 10 1
26 1 151695-66920 | AF (VYF4 Vy FIL | LABEL, HANDLE 1
2 1 13790-91451 | #\-A-ADYA-—YAYb | RIVET, PARKERIZED 4
SeLeh ed eM Uo td
eo MRR (HEAT) BER ee ia
Parts List of Link A’ ssy (Hydraulic Type) 60-54b-00 | 12
‘A: RHO 894i/S-tk#R, With RHD Type Governor Spec.
Ak
ep
Ww
om
DF FLYWHEEL
B : UG-8 A123/S7-4t4R, With UG-8 Type Governor Spec.
23484
POSITE SIDE OF FLYWHEEL reel
7 Sm—asaeaeeEY26
eet A coco
Cty
ea READ) BRR bee"
Parts List of Link A’ ssy (Hydraulic Type) ap
‘A: RMD A!4i/