Professional Documents
Culture Documents
The contract allowing you to use this document contains the following terms of use which must be
followed:-
(a) You may view and print a single copy of a document contained in the Subscription for reference
purposes only and only for internal purposes within the site on which such copies are made,
providing such copies are dated and destroyed after the reference usage, typically no more than 60
working days after use, subject to the exception described in clause (b) below. Such copies may not
be filed to form part of any hard copy reference collection.
(b) Where you have a specification or tender requirement to reproduce a document or portions of a
document as part of its documentation for external submission in response to a tender, the necessary
pages of the document, including the whole document if required, may be reproduced and submitted
provided a copyright notice is included. You shall notify SAI Global of any such use. For internal and
archival purposes only, a paper copy may be attached to your documentation and shall be
considered a permanent part of that documentation.
(c) Under no circumstances are you permitted to reproduce all or part of any document for external
use or for use in any other site or group of sites, except as set forth in (b) above.
(d) You may not remove any proprietary markings or electronic watermarks, including any
copyrights and trademarks.
(e) You may copy a maximum of 25% of the content of a document within the Subscription and
paste it to another document for internal use. The copied content in the new document must contain
a copyright notice “Copyright [name of publisher] Date where date is the date of copyrighted material.
Such content is licensed for use only for the duration of the relevant Subscription.
(f) For ISO standards, the material is reproduced from ISO publications under International
Organization for Standardization (ISO) Copyright License number SAI GLOBAL/MCEA/2008. Not for
resale. No part of these ISO publications may be reproduced in any form, electronic retrieval system
or otherwise, except as allowed under the copyright law in the country of use, or with the prior written
consent of ISO (Case postale 56, 1211 Geneva 20, Switzerland, email: copyright@iso.org) or ISO’s
Members.
SAI GLOBAL, Forest Road Office Centre, 210 Route 4 East, Paramus, NJ 07652, USA
201-986-1131. Fax: 201-986-7886. E-mail: sales@ili-info.com. www.ili-info.com
1
Copyrighted material licensed to SGS SA. No further reproduction or distribution permitted.
Printed / viewed by: [maribel.brochero@sgs.com] @ 2015-10-22
C22/C22M − 00 (2015)
10. Certification 11.2.1 Name of manufacturer,
10.1 When specified in the purchase agreement, a manufac- 11.2.2 Description of material, and
turer’s or supplier’s report shall be furnished at the time of 11.2.3 Net or gross weights, or both, of the package.
shipment certifying that the product is in compliance with this 11.3 When shipped in bulk, a card containing the required
specification. information in accordance with 11.2 shall be conspicuously
11. Packaging and Package Marking placed in the carrier.
11.1 Gypsum shall be shipped either in packages or in bulk. NOTE 1—State law may require additional information.
11.2 When shipped in packages for resale, the following
information (See Note 1) shall be legibly marked on each 12. Keywords
package or on a tag of suitable size attached thereto: 12.1 calcium sulfate; gypsum
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/