Professional Documents
Culture Documents
* See Manual for full CIP Object Model. 305 R Phase B RMS Voltage (L2-L3)
306 R Phase C RMS Voltage (L3-L1)
307 R Average RMS Voltage
Table 3. EtherNet/IP - S611 Default Assembly 308 R Motor Power (KW)
Default Input Word Data 314 R Motor Thermal Capacity %
Assembly 0x79
(121d) 0 Device Status 400 R/W Command Register
1 RMS Current 0x00AA - Reset Relay
Avg 0x00DD - Relay Off
2 RMS Voltage ** See Manual for full Modbus register map.
Avg
3 Latched Fault
Bits
Table 5. Modbus Registers - S611
Default Output Byte Data
Assembly 0x6A Modbus
(106d) 0 Control Byte Register R/W Description
Bit Bit Definition 300 R Motor Control Status
0 Run1 301 R Current Scale Factor
1 Permissive 302 R Phase A RMS Current
2 Fault reset 303 R Phase B RMS Current
3-5 Reserved 304 R Phase C RMS Current
6 Out 1 305 R Average RMS Current
7 Out 2 306 R Phase A RMS Voltage (L1-L2)
307 R Phase B RMS Voltage (L2-L3)
* See Manual for full CIP Object Model.
308 R Phase C RMS Voltage (L3-L1)
309 R Average RMS Voltage
310 R Motor Power (KW)
314 R Motor Thermal Capacity %
400 R/W Motor Control
** See Manual for full Modbus register map.
RS485 Ethernet
Example: Isolated 24Vdc Input
Example 120VAC IO Module RS485 Ethernet Source + -
- All inputs are isolated. - - Connect isolated power source
+ D1 D0
between C and Inputs. Pin 1
Pin 1 D1 D0
24VDC
24 +
24VDC
24 + Power Supply
Power Supply
0V -
0V -
C C
C C
24VDCISO
120VAC I1 I1
I1 I1
I2 I2 I2 I2
ON I3 I3 ON
I3 I3
OFF OFF
I4 I4 I4 I4
1 1
NO Q1 2 NO Q1 2
4 4
NO Q1 8 NO Q1
AC/DC
8
16
NO Q2 AC/DC 16
32 NO Q2 32
64
C C 128 64
C C 128
NC Q2
On
AC/DC NC Q2
On
AC/DC
Pin 12
Pin 12
Figure 1. C441R—120 Vac Input Specification Figure 2. C441T 24 Vdc Input Specification - Isolated
RS485 Ethernet
Example: Non Isolated 24Vdc Input Source
Table 6. 120 Vac Inputs - Connect C and 0V together. + -
- Use 24 to source inputs.
D1 D0
Specification Value Pin 1
Number of inputs 4
24 +
Nominal voltage 120V ac
Nominal current 15 mA 0V -
24VDC
Type 50/60 Hz Power Supply C C
Input type IEC 61131-2, type 1 digital I1 I1
I2 I2
I3 I3 ON
OFF
I4 I4
1
NO Q1 2
4
NO Q1 8
AC/DC 16
NO Q2 32
64
C C 128
NC Q2
On
AC/DC
Pin 12
Certifications Reference
Agency certifications UL® 508 C441/Standalone I/O Manual MN04201001E
cUL® (CSA® C22.2 No. 14)
S611 Manual MN03902011E
CE (low voltage directive)
EtherNet/IP conformance tested
Description Rating
Transportation and Temperature -40°C to 85°C (-40°F to 185°F)
Storage Humidity 5-95% non condensing
Operating Temperature -20°C to 55°C (-4°F to 131°F)
Humidity 5-95% non condensing
Altitude Above 6600 ft (2000m)
Consult factory
Shock 15G any direction for 11 ms
IEC 60068-2-27
Vibration 5-150 Hz, 3G, 0.42mm
IEC 60068-2-6 peak-to-peak
Pollution 3
Degree
Notes:
For use with Eaton UL Listed Power Supply Catalog Nos. PSS55A,
PSS55B, PSS55C or PSS160E.
Eaton Corporation
Electrical Sector
1000 Cherrington Parkway
Moon Township, PA 15108
United States
877-ETN-CARE (877-386-2273)
Eaton.com PowerChain Management is a registered
© 2012 Eaton Corporation trademark of Eaton Corporation.
All Rights Reserved
Publication No. IL04209008E / Rev 005 All other trademarks are property of their
February 2012 respective owners.