Professional Documents
Culture Documents
T.A.MATRIX Plumbing NC II
T.A.MATRIX Plumbing NC II
FACILITIES TOOLS
TRAINING TRAINEE & VENUE DATE & REMARKS
TIME
ACTIVITIES EQUIPMENT
WORKSTATION AREA
-PRELIMINARIES Power point
1. Prayer Presentation
2. Attendance ALL TRAINEES Computer
Projector
3. Orientation on school policies
Workshop Layout
4. Orientation on CBT Delivery and TR/CBC
different components CBLM LECTURE
Attendance Sheet ROOM
Pen & Paper
Data Gathering
Sheet
Pre-test
1. PREPARE ESTIMATION OF MATERIALS FOR MULTIPLE PLUMBING UNITS
-STUDY APPROVED PLUMBING PLAN
All measurements in the plans Plumbing Blue
are determined in accordance Print Work Shop
with job requirements with job ALL TRAINEES Plumbing plan Area
requirements and details. Structural plan
Plumbing legends, symbols and Architectural plan
abbreviations are identified and Site development
interpreted in accordance with plan
job requirements. Mechanical plan
Electrical plan
Specification of materials are Plumbing Legend,
identified in the plan according Symbols and
to the job requirements. abbreviation.
Plumbing layout is Floor plan
determined/visualized based on Schematic
isometric drawing, schematic diagram of (DWV)
water line
diagram and details.
When necessary, cost of
materials are estimated based
on the current market price.
- ESTIMATE & FINALIZE MATERIALS
TAKE-OFF
Materials are estimated in Plumbing Blue
accordance with the job Print
requirements. Plumbing plan
Materials and consumables are Structural plan Work Shop
quantified and listed in ALL TRAINEES Architectural plan Area
accordance with the job Site development
requirements. plan
All results are summarized for Mechanical plan
submission in accordance with Electrical plan
job requirements. Plumbing Legend,
Bill of materials and cost Symbols and
abbreviation.
estimate is presented to client /
Floor plan
supervisor for approval.
Schematic
diagram of (DWV)
water line
2. PERFORM MULTIPLE PLUMBING UNITS INSTALLATION AND ASSEMBLIES
- PREPARE MATERIALS FOR Steel tape
DRAINAGE, SANITARY, VENT AND Ballpeen hammer
WATERLINE LAYOUT WORK Hacksaw w/ blade
Work instructions/ plans are Blow torch
read and interpreted in Pointed steel
chisel
accordance with the job Manual pipe Work Shop
requirements. Threader ( ¼’’ – 2’’ Area
Materials, tools, and ALL TRAINEES )
equipment are selected and Pipe wrench ( 10’’,
12’’, 14’’, 18’’, 24’’)
prepared according to job
Pipe vise
requirements.
Bar/hose level
Appropriate PPE are selected
Plumb bob
according to job requirements. Pipe cutter
Pipe reamer
Threading
machine
Welding Machine
Test pump (
manual / power
driven)
Electric grinder
Fushion machine
Grooving machine
Pliers
Wrenches ( open,
box, combination,
adjustable, socket,
allen)
- INSTALL PIPES & FITTINGS FOR
DRAINAGE, SANITARY, VENT AND Steel tape
WATERLINE LAYOUT. Ballpeen hammer
Pipes and fittings are installed Hacksaw w/ blade
as indicated in the approved Blow torch
Work Shop
working plan. ALL TRAINEES Pointed steel
chisel Area
Pipe supports and braces are
installed in accordance with the Manual pipe
Threader ( ¼’’ – 2’’
approved working plan.
)
Correct use of materials, tools Pipe wrench ( 10’’,
and equipment is observed in 12’’, 14’’, 18’’, 24’’)
accordance with manufacturer’s Pipe vise
instruction manual. Bar/hose level
Appropriate PPE is used in Plumb bob
accordance with the job Pipe cutter
requirements. Pipe reamer
Threading
machine
Welding Machine
Test pump (
manual / power
driven)
Electric grinder
Fushion machine
Grooving machine
Pliers
Wrenches ( open,
box, combination,
adjustable, socket,
allen)