Professional Documents
Culture Documents
DONATE
Centrifuge
A centrifuge was the first device to separate chemical isotopes, used by Jesse Beams
of the University of Virginia to separate chlorine-35 from chlorine-37 in 1934. In 1940,
American physicists thought that the centrifuge was the best possibility for large-scale
enrichment, and Beams received government money to attempt uranium enrichment via
centrifuge.
Centrifugal force in a cylinder spinning rapidly on its vertical axis would separate a
gaseous mixture of two isotopes. This is because the lighter U-235 isotope would be
less affected by the action and could be drawn off at the top center of the cylinder. A
cascade system composed of thousands of centrifuges could produce a rich mixture.
Beams pioneered this method and received much of the early funding.
A high-speed centrifuge initially seemed promising for uranium enrichment, but the
Manhattan Project failed to produce a workable model, and research stopped during the
war. The centrifuge Beams constructed could separate U-235 from U-238, but required
huge amounts of energy and could only sustain a short run before breaking down; in
other words, it was not suited for industrial production. Manhattan Project scientists
opted to pursue gaseous diffusion over gas centrifuges as the primary method for uranium isotope separation, and in January 1944
Army support for the gas centrifuge method was dropped.
In the early 1950s, however, a German POW in the Soviet Union produced an efficient and durable centrifuge. Because the centrifuge
does not require massive capital investment or special equipment, it is the preferred method of separation today, and poses the biggest
threat for proliferation.
While centrifuges were thought a lost cause in American nuclear engineering, scientists abroad continued to work on them. Soviet
physicists felt, correctly, that gaseous diffusion did not make sense, since it would use more power than it could produce. Fritz Lange, a
German émigré working for the Soviet program, set to work on constructing a centrifuge. All his designs, however, used a horizontal
centrifuge, which would invariably break due to the pull of gravity on the underside.
Max Steenbeck and Gernot Zippe, prisoners of war from Germany and Austria, were the next to tackle problem. Working in a POW camp,
Steenbeck and Zippe made several improvements on Beam's design. The centrifuge rotor was made to spin on the tip of a needle, like a
top, thus eliminating friction, while the centrifuge was spun via an electromagnetic field. Though it took more research to adapt this to a
scalable design, the basic design problems had been solved.
After release from the prisoner camp, Steeneck returned to East Germany, while Zippe traveled the world, marketing his centrifuge.
In the late 1950s, Zippe worked as a researcher at the University of Virginia, where he built a centrifuge largely from memory. Atomic
Energy Commission officials marveled at the simplicity of his design. Subsequent US efforts to build a centrifuge progressed very
smoothly. Because a functioning uranium-enrichment centrifuge can be built fairly quickly by a small team without prior experience,
there are little technical barriers to proliferation. This design would spread to become the main method for enriching uranium, and
remains so today.
Electromagnetic Separation
The electromagnetic method, pioneered by Alfred Nier of the University of Minnesota, used a mass spectrometer, or spectrograph, to
send a stream of charged particles through a strong magnetic field. Atoms of the lighter isotope (U-235) would be deflected more by the
magnetic field than those of the heavier isotope (U-238), resulting in two streams that could then be collected by different receivers.
The electromagnetic method as it existed in 1940, however, would have taken too long to separate quantities sufficient to be used in
the current war. In fact, 27,000 years would have been required for a single spectrometer to separate 1 gram of uranium-235.
Ernest O. Lawrence of the Radiation Lab at the University of California at Berkeley favored this method and converted his giant cyclotron
to accomplish this form of separation more efficiently. This model led to the eventual design and construction of the huge Y-12 Plant
complex at Oak Ridge, Tennessee. Because of its exorbitant cost, electromagnetic separation was largely abandoned after the war for
weapons production, but it played an important role in the development of the field of nuclear medicine.
Gaseous Diffusion
Gaseous diffusion’s principle was simple: molecules of a lighter isotope would pass
through a porous barrier more readily than those of a heavier isotope. The tiny weight
difference between U-235 and U-238 meant that initial separation would be negligible.
Repeat the process hundreds of times in sequential "cascades," though, and the end
product would be significantly enriched uranium.
Centrifuge research faltered in 1942, and General Leslie Groves pushed for more
research into gaseous diffusion. In mid-1943, Roosevelt and Churchill signed the
Quebec Agreement, under which British nuclear research was subsumed into the
Manhattan Project; this meant full exchange of information. But serious problems
remained. Besides the need for a porous barrier, component design would have to
accommodate uranium hexafluoride, one of the most corrosive gases in the world.
Groves soon ordered the construction of K-25, but as construction crews cleared the site and poured the foundation it was still unclear
what exactly was going to go inside the plant. To protect the pipes from corrosion, contractors undertook the new process of nickel
coating. Sealing the pipes was also a problem, as grease would interfere with the process and uranium hexafluoride could not be
permitted to leak out. The eventual solution was a completely novel seal material: Teflon.
Kellex Corporation undertook the barrier problem: developing a thin metal membrane with millions of tiny openings. After months of
research and competition with an incomplete design from the team at Columbia, Groves accepted the Kellex design and ordered it
installed in K-25. K-25, the largest roofed building in the world upon construction, would eventually serve as an intermediary step
between S-50 and Y-12. Gaseous diffusion was important throughout the Cold War, but uses far more energy than centrifuges, and is
now nearly obsolete.
Like other enrichment methods, liquid thermal diffusion was at an early stage in 1940.
Abelson eventually relocated his experimentation to the Naval Research Laboratory in
Washington, DC, whereupon money was obtained to construct a pilot plant at the
Philadelphia Navy Yard. When Oppenheimer learned the Navy was using liquid thermal
diffusion for enriched uranium in submarines, the Manhattan Project subsequently built
the S-50 Plant, which enriched uranium slightly before it was sent to K-25 and Y-12 for
further enrichement. The inefficiency of this method meant that, like electromagnetic separation, it was obsolete after the war.
[The text for this page was adapted and taken from the U.S. Department of Energy's official Manhattan Project history: F. G. Gosling,
The Manhattan Project: Making the Atomic Bomb (DOE/MA-0001; Washington: History Division, Department of Energy, January 1999), 5-
6.]
Browse our collection of oral histories with workers, families, service members, and more about their experiences in the Manhattan
Project.
Tour some of the key locations of the Manhattan Project with an audio guide.
MAIN MENU
DONATE
info@nuclearmuseum.org Contact Us