Professional Documents
Culture Documents
7:167D
April 2009
P1185 P1184
Type 167D Two-way Switching Valve Type 167DA Three-way Switching Valve
Introduction
The 167D Series switching valves are typically used • Sour Gas Service Capability—NACE MR0175
to deliver constant reduced pressure of gaseous and MR0103 compliant construction available.
fluids to pilot-operated controllers and other • Optional Stainless Steel Construction—
pneumatic instrumentation. The Types 167DS and 167DAS provide high
• The Types 167D and 167DS are two-way resistance to corrosion especially beneficial in
switching valves. offshore applications.
• The Types 167DA and 167DAS are three-way
• Ease of Maintenance—No special tools are
switching valves.
required to perform maintenance, and
all maintenance can be performed with the
Features valve in the line.
• Compact—The Types 167D and 167DA • Rugged Construction—The Types 167D and
switching valves are engineered for outstanding 167DA switching valves are engineered for longer
performance in a compact, lightweight package. service life with minimal maintenance requirements.
• Easy, Accurate Adjustment—With a choice of • Corrosion Resistant Fasteners—Bolting and
springs for optimum resolution, the switching point adjusting screw are double zinc-chromated for
is set to a specific requirement by an adjusting enhanced corrosion resistance. Optional stainless
screw atop the spring case. steel bolting and adjusting screw are also available.
D103235X012
www.emersonprocess.com/regulators
Bulletin 71.7:167D
Specifications
Body Size, Inlet and Outlet Connection Style Spring Case Vent Location
Ports A and C: NPS 1/4 or 1/2, NPT Aligned with inlet standard, other positions optional
Vent and Control Pressure Connections
(Port D) and Port B: 1/4 NPT Material Temperature Capabilities(1)
Nitrile (NBR)
Construction Materials Standard Bolting: -20° to 180°F (-29° to 82°C)
See Table 3 Stainless Steel Bolting: -40° to 180°F (-40° to 82°C)
Maximum Inlet Pressure (Body Rating)(1) Fluorocarbon (FKM):
400 psig (27,6 bar) 0° to 300°F (-18° to 149°C)
Set Pressure Ranges Options
See Table 1 All Types
Maximum Diaphragm Pressure(1) • Handwheel adjusting screw
50 psi (3,4 bar) over outlet pressure setting • NACE MR0175 or NACE MR0103 construction(2)
• Panel mount (includes spring case with 1/4 NPT
Flow and Sizing Coefficients vent, handwheel, and panel mounting nut)
See Table 2 • Closing cap (available on spring case with
Approximate Weights 1/4 NPT vent)
Types 167D and 167DA: 1.2 pounds (0,5 kg) • Fluorocarbon (FKM) elastomers for high
Types 167DS and 167DAS: 2.8 pounds (1 kg) temperatures and/or corrosive chemicals
• Stainless steel stem and valve plug
1. The pressure/temperature limits in this Bulletin and any applicable standard or code limitation should not be exceeded.
2. Product complies with the material requirements of NACE MR0175 or MR0103. Environmental limits may apply.
2
Bulletin 71.7:167D
Adjusting screw
Adjusting screw
Control spring
diaphragm
soft seat
Control spring
O-RING
diaphragm
soft seat
O-RING
port a port c
BODY
valve plug
TYPE 167D two-way switching valve TYPE 167DA three-way switching valve
inlet pressure
outlet pressure
atmospheric pressure INLET PRESSURE
loading pressure OUTLET PRESSURE
ATMOSPHERIC PRESSURE
LOADING PRESSURE
INTERMEDIATE PRESSURE
Figure 2. 167D Series Operational Schematics (Port D not shown)
PILOT SUPPLY PRESSURE
INTERMEDIATE BLEED PRESSURE
PRE-EXPANSION PRESSURE
SSURE VACUUM PRESSURE
E Table 3. Construction Materials TANK PRESSURE
SSURE BYPASS PRESSURE
SSURE PUMP PRESSURE
ED PRESSURE BACK PRESSURE Types
ESSURE part name
E 167D and 167DA 167DS and 167DAS
INLET PRESSURE Body and
OUTLET PRESSURE INLETCase
Spring PRESSURE Aluminum (ASTM B85/Alloy 380) CF8M/CF3M Stainless steel
OUTLET PRESSURE
ATMOSPHERIC Spring
PRESSURE
Retainer Aluminum 316L Stainless steel
LOADING PRESSURE ATMOSPHERIC PRESSURE
Upper Spring Seat
LOADING PRESSURE Zinc-plated steel
INTERMEDIATE PRESSURE 316 Stainless steel
INTERMEDIATE PRESSURE
PILOT SUPPLY Diaphragm Plate
PRESSURE Chromate conversion coated Aluminum
INTERMEDIATE Control
BLEED PRESSURE
PILOTSpring
SUPPLY PRESSURE Zinc-plated steel and Chrome Silicon Inconel®
PRE-EXPANSION PRESSURE
INTERMEDIATE BLEED PRESSURE
VACUUM PRESSURE Valve Stem
PRE-EXPANSION PRESSURE Brass or Aluminum
TANK PRESSURE VACUUM PRESSURE 316L Stainless steel
BYPASS PRESSURE Valve Plug Brass or 316L Stainless steel
TANK PRESSURE
PUMP PRESSURE Valve Spring
BYPASS PRESSURE 302 Stainless steel or Inconel® (NACE)
BACK PRESSURE PUMPO-Rings,
Diaphragm, PRESSURE Nitrile (NBR) or Fluorocarbon (FKM)
BACK
and PRESSURE
soFt seat
Bolting,
Zinc-plated steel Zinc-plated steel or 316 Stainless steel
Adjusting Screw
HEXNUT Zinc-plated steel or 316 Stainless steel 316 Stainless steel
Handwheel Zinc-plated steel screw with resin handwheel
3
Bulletin 71.7:167D
d PRESSURE GAUGE
type a c
dvc6010 b
WHISTLE
a
A c
type 657 b
1/4 npt
COOLING TOWER
supply TO INSTRUMENT AIR SUPPLY
PUMP
55 PSI (3,8 bar)
PUMP DISCHARGE
type
67cfr
10C0622 AF8400
Figure 3. Typical 167DA or 167DAS Installation Figure 4. Typical 167D or 167DS Installation
(Lockup system using Type 167DA or 167DAS (Warning system using Type 167D or 167DS two-way
to close air circuit to diaphragm of main valve in valve to activate a whistle when pump discharge
case of plant air failure. Main valve will remain in pressure falls.)
position it occupied at time of supply pressure failure.)
4
Bulletin 71.7:167D
type 167da
or 167das
asco solenoid
de-energized
S
d 1 2
a c 3
b
vent
volume tank
1/4 npt
shipped with actuator
GE37992 3/4 npt
position 3
position 4
position 2
GE31784
5
Bulletin 71.7:167D
2.98
(76)
1.49
(38)
vent
3.69
MAX
(94)
side outlet
1/4 npt
2.78
(71)
2.75
(70)
0.63
(16)
inlet connection
1/2 npt and outlet connection
optional 1/2 npt and
1/4 npt optional 1/4 npt
GG01159
Inches
(mm)
6
Bulletin 71.7:167D
Ordering Guide
Type (Select One) Diaphragm, O-Rings, and Valve Plug (Select One)
167D (two-way, aluminum)*** Nitrile (NBR) (standard)***
167DS (two-way, stainless steel)*** Fluorocarbon (FKM)**
167DA (three-way, aluminum)*** Spring Case Vent Location (Select One)
167DAS (three-way, stainless steel)*** Position 1 - Aligned with inlet (standard)***
Body Size (Ports A and C) (Select One) Position 2
NPS 1/4, NPT Position 3
NPS 1/2, NPT Position 4
Quantity (Specify) NACE MR0175 Construction (Optional)(1)
Yes (not available with gauge)**
Spring Case Style (Select One)
Drilled hole vent (Types 167D and 167DA standard)*** NACE MR0103 Construction (Optional)
1/4 NPT vent Yes (not available with gauge)**
(Types 167DS and 167DAS standard)*** Replacement Parts Kit (Optional)
Single hole panel mount*** Yes, send one replacement parts kit to match
Adjusting Screw (Select One) this order.
Square head (Types 167D and 167DA standard)***
Square head with closing cap
(Types 167DS and 167DAS standard)***
Handwheel***
Set Pressure Range (Select One)
0 to 15 psig (0 to 1,0 bar)***
0 to 20 psig (0 to 1,4 bar)***
0 to 35 psig (0 to 2,4 bar)***
0 to 60 psig (0 to 4,1 bar)***
0 to 125 psig (0 to 8,6 bar)***
0 to 150 psig (0 to 10,3 bar)
(Types 167DS and 167DAS only)***
Specification Worksheet
Application (Please designate units):
1. Product complies with the material requirements of NACE MR0175. Environmental
limits may apply.
Specific Use
Line Size
Gas Type and Specific Gravity
Gas Temperature
Does the Application Require Overpressure Protection?
Yes No If yes, which is preferred:
Relief Valve Monitor Regulator
Shutoff Device
Is overpressure protection equipment selection assistance
desired?
Pressure (Please designate units):
Maximum Inlet Pressure (P1max)
Minimum Inlet Pressure (P1min)
Downstream Pressure Setting(s) (P2)
Regulators Quick Order Guide Maximum Flow (Qmax)
*** Readily Available for Shipment
Performance Required:
** Allow Additional Time for Shipment Accuracy Requirements?
Special Order, Constructed from Non-Stocked Parts. Need for Extremely Fast Response?
* Consult your local Sales Office for Availability.
Other Requirements:
Availability of the product being ordered is determined by the component
with the longest shipping time for the requested construction.
7
Bulletin 71.7:167D
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls, Inc., a
business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson
Process Management product remains solely with the purchaser.
©Emerson Process Management Regulator Technologies, Inc., 2009; All Rights Reserved