Professional Documents
Culture Documents
XR2 RemoteControl Rev 122911 PDF
XR2 RemoteControl Rev 122911 PDF
Enjoy your your remote to control your TV. Digital Transport Adapter GENERAL TROUBLESHOOTING Esto es lo que tu control remoto puede hacer.
XFINITY TV ®
Remote Control Q: Why does the All Power button flash
Program your remote functions (Power, VOL+, VOL – and Mute), codes on the back of this guide, follow the and is no further than 15 feet away. Also, All Power: One button to turn on/off both
All Power: Un sólo botón para encender/
to get started. follow the steps below: steps below to search for your code. make sure your digital set-top box or DTA the TV and set-top box.
apagar tu televisor y tu caja decodificadora.
1. Turn on your TV. is powered on and in plain sight.
VOL+/ – : Sube y baja el volumen de tu
HERE’S HOW: 2. On your remote, press and hold the Setup SAVE YOUR TV CODE Q: W hy does the All Power button flash VOL+/ – : Turns the volume up and down
DTA o caja decodificadora. Después de que
1. Install the batteries. button for 3 seconds until the All Power For future reference, write the valid red then green while I am programming on the DTA or set-top box. After your remote
tu control remoto esté programado, estos
button changes from red to green. manufacturer’s code for your TV here: my remote? is programmed, these keys operate the TV’s
2. Find the manufacturer’s code for your TV botones operan el control del volumen de tu
3. Enter 9-9-1. The All Power button will A: You may have entered the wrong code. volume control.
(see other side). televisor.
flash green, twice. Check the code and try programming again.
3. Turn on your TV and digital set-top box CH / : Selects the next higher
4. Press the CH button multiple times until CH / : Selecciona el siguiente canal
or DTA (Digital Transport Adapter).
the TV turns off.
PAIRED REMOTE or lower channel.
hacia arriba o hacia abajo.
4. On your remote, press and hold the TROUBLESHOOTING Mute: Turns the sound on and off.
Setup button for three seconds until 5. After the TV turns off, press Setup. Mute: Enciende y apaga el sonido.
Q: W hen paired, why does the All Power
the All Power button changes from red button flash green then red when
to green. pressing a button on the remote?
Helpful Tip: Additional remote control
5. Enter the first manufacturer’s code you Video Controls: Controlan la visualización
programming support, including code lookup A: The device you are paired with may not
found in Step 2. The All Power button Video Controls: Controls On Demand or de On Demand o DVR, Play (reproducir)/
tools and frequently asked questions, can be be powered on or you might be out of
will flash green twice. DVR viewing, Play/Pause, Fast-Forward, Pause (pausa), Fast-Forward (avanzar
found at www.xfinity.com/remotes. communication range. Make sure the
Rewind and Exit/Stop. rápidamente), Rewind (retroceder
6. Press the TV Power button on the Additional Feature: If you would like device is powered on and move closer to the
rápidamente) y Exit (salir)/Stop (parar).
remote control. If the TV turns off, you to place your digital set-top box or DTA device. If this does not work, try re-pairing
your remote by following the instructions in Replay: Jumps back 15 seconds within an
know the code has been accepted. Turn out of line of site (for example, in an Replay: Retrocede 15 segundos dentro de
the TV back on and make sure that the “Installing your digital set-top box or DTA out On Demand or DVR program.
entertainment center or behind your TV), un programa de On Demand o en el DVR.
VOL+/ – and Mute buttons also work. follow the instructions above to program the of sight.”
Rec: Records content currently being
If so, you’re all set! remote control for your TV, then refer to the Rec: Graba el contenido que se está viendo
Q: How
can I tell which digital set-top box viewed.
7. If not, repeat these steps using the next “Installing your digital set-top box or DTA out or DTA my remote control has been en ese momento.
manufacturer’s code found in Step 2 (You of sight” instructions on the other side of this paired with? Note: Some features above require a DVR
may need to try several codes to find instruction sheet. set-top box and/or access to On Demand Nota: Algunas funciones mencionadas
XFINITY XR2 A: Once paired to a device, the remote will anteriormente requieren de una caja
the one that works for your TV). If you only work with that specific set-top box programming.
Remote Control still can’t find a code that works, see the xfinity.com/remotes or DTA. Color-coded stickers have been
decodificadora de DVR o acceso a la
programación On Demand.
USER’S GUIDE
“Can’t Find Your Code?” section. included in the packaging to make it easier
to quickly identify which device is paired
with your remote.
XFINITY/Menu: Ingresa a los menús de la
XFINITY/Menu: Enters the on-screen
guía en pantalla.
guide menus.
Guide: Atajo a los listados de televisión.
Guide: Shortcut to TV listings.
¡Disfruta de Programar tu control remoto para OK: Selecciona el artículo resaltado dentro
controlar tu televisor es sencillo. Diagnóstico de problemas OK: Selects the highlighted item within de la guía.