Professional Documents
Culture Documents
Wipers Washers and Horn
Wipers Washers and Horn
Front wiper washer system ........... Four Driver control unit input and output signals
No. reference value .................................................. ...... 35
D
System Overview .............................................. . . . . . .Four
Driver control unit Wye - BCM Input and output signal reference value ................................. 36
Per switch reading function .............................. Eight - IPDM E / R Input and output signal reference value ......................... 36
· Component mounting position ....................................... . . . . 11 Back door control unit input and output signals
·circuit diagram .................................................. ........... Twelve No. reference value .................................................. ...... 36
E
Driver control unit input and output signals - How to proceed with fault diagnosis .......................................... 37
- BCM Input and output signal reference value .............................. . . . . 13 - Phenomenon by fault diagnosis Chart .................................. 39
- IPDM E / R Input and output signal reference value ...................... . . . . 13 Rear wiper of the power supply and the ground circuit system ... . . . 40
Wiper amplifier input and output signal reference value ............. . . . . 14 Rear wiper actuation signal system ........................... 41 F
- How to proceed with fault diagnosis ....................................... . . . . 15 Rear wiper motor system ........................... 41
And diagnosis before inspection ................................................. . . . . 15 Rear wiper position detection signal system .................... 42
- Phenomenon by fault diagnosis Chart ................................... 17 Judder occurrence correspondence at the time of .................................. 43
G
Of the wiper amplifier power supply and the ground circuit system .... 17 And removal of the rear wiper arm, mounting ... 43
Front wiper actuation signal system ..................... 19 Rear wiper arm of the stop position adjustment ............. 44
Front wiper motor system ..................... Twenty And removal of the rear wiper motor, Installing
Front wiper motor drive signal system ....... twenty one け .................................................. ................. 44
- Auto-stop signal system ............................ . . . .twenty two Rear wiper blade .................................. 46
H
Judder occurrence correspondence at the time of ................................... twenty three Rear washer injection adjusting the position of the nozzle ... . . . 46
- Removing the front wiper arm, take Rear washer hose route ........................ 46
Bill .................................................. .......... . . . .twenty four And removal of the rear washer nozzle, take
Front wiper arm of the stop position adjustment ....... twenty four Bill .................................................. ............. 47
Removing the front wiper motor link Rear wiper washer switch circuit I
Front washer nozzles of the injection position adjustment - Acquisition of rear wiper-washer switch
Washer hose route ............................ . . . . 27 - Removing the rear wiper washer tank
Remove, mounting ............................................. 47 JA
- Removing the front washer nozzles,
attachment .................................................. ....... 28 - Removing the rear wiper washer pump
Remove, mounting ............................................. 47
Front wiper washer switch
Inspection of the circuit .................................................. ... 28 Horn .................................................. ............ . . . 48
WW - 1
Notes on work
SRS Air bag, care about the pre-tensioner seat belt with a car JKS00C4D
warning : • SRS The configuration of the associated air bag and pretensioner seat belt system components desorption and harness desorption, key
switch OFF In, disconnect the negative battery terminal Three It is carried out after leaving more than minute. (For discharging the electricity stored in the auxiliary power
• The desorption of the components, air tools and power tools, etc. that you do not use.
• SRS Air bag and harness for the pre-tensioner seat belt system is, that you do not repair by solder or the like. In addition, careful attention should be given to
interference with the biting and other parts of the harness.
• SRS That you do not use the electric tester such as circuit testers when the inspection of the air bag and pretensioner seat belt circuit and
separately state. (Working prevention by fine current of the tester)
• The connector of the air bag module and pre-tensioner seat belts, of foreign matter such as a driver plug is not. (Working preventing
electrostatic)
• SRS The airbag and pretensioner seat belt, using the yellow harness connector as identification, and to distinguish from other harness.
• For safety reasons, maintenance work, " SB Seat belt "and" SRS SRS Making reference to the air bag. "
• In front wiper operation, when the wiper by obstacles such as snow is no longer able to operate, it is possible to stop the operation of the wiper for motor
protection. In that case, the switch OFF After the removal of the obstacles to, about Twenty Again switch from elapsed seconds or more ON Front wiper begins to
• Due to factors such as snowfall, the operation of the rear wiper Ten If you stop sec or more BCM But to stop the operation of the rear wiper for motor protection. In this
case after removing the cause of the stop, once the rear wiper switch OFF To to One The rear wiper switch after minute ON Or INT Resume the operation to be in.
• When I opened the hood in a state in which the front wiper was locked back, it might damage the hood.
• When the coating unevenness or part of the oil film adhesion and glass coating agent such as wax on the windshield glass is there is peeling, there is a case where a positive not always be
• In continuous washer pump Thirty If the second is operated more, and cause of failure.
WW - 2
Prepared by
name Use
CONSULT- Ⅱ B
EG1187 0001
Diagnostic program card
EG1187 0100
(version JJD02A )
PBIA3527J
diagnostic connector
PBIA3526J
JA
WW
WW - 3
Front wiper washer system
• BCM Key switch ON Body the signal and the vehicle speed signal CAN And transmits it to the driver control unit using the communication.
• Wiper switch (combination switch) is Five And One of the output terminal Five One of which is constituted by the combination of the input terminals, the
combination state driver control unit terminals when switched on reads.
• The driver control unit of the front wiper LO , HI as well as INT To send an activation signal to the wiper amplifier.
• Wiper amplifier LO , HI as well as INT To operate the front wiper motor by the actuation signal.
Feature Description
System chart
SKIA2966J
• Key switch ON Sometimes, the driver control unit Front wiper by the reading function of the combination switch LO But ON Upon detection of the
state, the front wiper to the wiper amplifier LO To send an actuation signal.
• Wiper amplifier front wiper LO Upon receiving the operation, the relay built in the wiper amplifier ON By, the front wiper motor LO Actuate.
• Key switch ON Sometimes, the driver control unit Front wiper by the reading function of the combination switch HI But ON Upon detection of the
state, the front wiper to the wiper amplifier HI To send an actuation signal.
• Wiper amplifier front wiper HI Upon receiving the operation, the relay built in the wiper amplifier ON By, the front wiper motor HI Actuate.
• Key switch ON Sometimes, the driver control unit Front wiper by the reading function of the combination switch INT But ON Upon detection of the
state, to the following working.
1. Between the combination switch ass volume 1, 2, 3 of ON / OFF It detects the state, to determine the wiper volume.
2. BCM Body from CAN A vehicle speed signal received by the communication, by the wiper volume, while calculating the ass pause time (seconds)
You. After confirming the auto-stop signal, Front wiper between every calculated ass pause time INT To send a signal to the wiper amplifier.
WW - 4
Front wiper washer system
• Wiper amplifier front wiper INT Upon receiving a signal from the driver control unit, a relay that is built in a wiper amplifier ON By, front wiper motor LO
In between to ass working.
• The washer switch about 0.4 Sec or more ON Then, the wiper motor to work.
• The washer switch ON → OFF If you, OFF The wiper motor about from the time that became a Three Time to operate.
• The washer switch during intermittent working ON Then prioritize the washer switch. B
Mist working
• MIST In automatic return type, any to the wiper One When you want to move only times and, a fine rain INT Even at the operating, to use when wiper actuation
feels early.
C
• With regard to working LO In the same control and the operation, the wiper One Time working to stop.
JA
WW
WW - 5
Front wiper washer system
DESCRIPTION OF OPERATION
circuit diagram
TKWA0481J
• 80A ( F / L-3 From) IPDM E / R of Two Backup power voltage is supplied to turn the terminal.
• IPDM E / R Department of 20A (# 74 Through) 38 From turn jack on the front wiper relay Five Backup power voltage is supplied to turn the terminal.
The key switch ON If you, the front wiper relay ON Next to the front wiper relay Three The turn terminal of the street Wye Paanpu Five The voltage is
supplied to the turn terminal. at the same time BCM The body is CAN Key switch using the communication ON And it transmits the signal to the driver control
unit. The front wiper switch LO When you position, the combination switch front wiper LO Of contact ON become, INPUT 1 and OUTPUT3 Circuit is conducting
of.
WW - 6
Front wiper washer system
The driver control unit is front wiper by the reading function of the combination switch LO But ON Upon detection of Jo on purpose, the driver control
unit Five From turn terminal of the wiper amplifier Six Front wiper to turn terminal LO
To send an actuation signal. Front wiper LO Wiper amplifier which receives the actuation signal, the built-in relay ON Then, of the wiper amplifier One From turn terminal of the
wiper motor One Supplying a voltage to turn the terminal, the wiper motor Three Of the wiper amplifier through the turn terminal Three To the ground in turn end child, the front
wiper LO Actuate.
B
Front wiper HI Actuation
• 80A ( F / L-3 From) IPDM E / R of Two Backup power voltage is supplied to turn the terminal.
• IPDM E / R Department of 20A (# 74 Through) 38 From turn jack on the front wiper relay Five Backup power voltage is supplied to turn the terminal.
C
The key switch ON If you, the front wiper relay ON Next to the front wiper relay Three The turn terminal of the street Wye Paanpu Five The voltage is
supplied to the turn terminal. at the same time BCM The body is CAN Key switch using the communication ON And it transmits the signal to the driver control
unit. The front wiper switch HI When you position, the combination switch front wiper HI Of contact ON become, INPUT2 When OUTPUT1 Circuit is conducting
of.
D
The driver control unit is front wiper by the reading function of the combination switch HI But ON Upon detection of the state, the driver control unit Six From turn
terminal of the wiper amplifier Seven Front wiper to turn terminal HI To send the work dynamic signal. Front wiper HI Wiper amplifier which receives the actuation
signal, the built-in relay ON Then, of the wiper amplifier Three Turn terminal or al wiper motor Three Supplying a voltage to turn the terminal, the wiper motor Two Of
E
the wiper amplifier through the turn terminal Two To the ground in turn terminal, the front wiper HI Actuate.
Intermittent working F
• 80A ( F / L-3 From) IPDM E / R of Two Backup power voltage is supplied to turn the terminal.
• IPDM E / R Department of 20A (# 74 Through) 38 From turn jack on the front wiper relay Five Backup power voltage is supplied to turn the terminal.
The key switch ON If you, the front wiper relay ON Next to the front wiper relay Three The turn terminal of the street Wye Paanpu Five A voltage is supplied G
to the turn terminal. at the same time BCM The body is CAN Key switch using the communication ON To send a signal to the de Rye bar control unit. The front
wiper switch INT When you position, the combination switch front wiper INT Of contact ON become, INPUT2 When OUTPUT3 Circuit is conducting of.
The driver control unit is the front wiper is state of the combination switch INT ON To the following working and it is determined that the.
1. Intermittent volume One , Two as well as Three of ON / OFF The state, wiper INT Driver control unit is detected in the same manner as the
I
Then, to determine the state of the wiper volume. Detail is "Intermittent working" ( WW-10 page ) See.
2. BCM Body from CAN A vehicle speed signal received by the communication, by the wiper volume, while calculating the ass pause time (seconds)
To. Of the front wiper motor Five From turn terminal of the driver control unit Twenty After confirming an O-toss top signal to be input to turn terminal, Of
driver control unit for each between calculated ass pause time Five From turn terminal of Wye Paanpu Six Front wiper to turn terminal INT To send a
JA
signal.
WW
WW - 7
Front wiper washer system
Vehicle speed about 35km / h More than the vehicle speed about 65km /
h The following vehicle speed about 65km / h that's all
Vehicle
Pause interval stop the vehicle speed at about 5kmspeed about
/ h that's all 35km / h Less than
Reference: A vehicle speed in the table may differ from the actual speed.
Front wiper INT Wiper amplifier which receives the actuation signal, the built-in relay ON Then, of the wiper amplifier One From turn terminal of the wiper motor One To supply a
voltage to turn the terminal, the front wiper motor Three Of the wiper amplifier through the turn terminal Three To the ground in turn terminal, the front wiper LO In between to
ass working.
• 10A (# twenty two ) From the combination switch Fifteen The power supply voltage is supplied to the turn terminal. When the front wiper switch on
the front washer position, the combination switch Five Watch- Shah motor from turn terminal One Supplying a voltage to turn the terminal, the
combination switch Sixteen , 14 Through the turn terminal is grounded, front washer motor is activated. Front washer motor 0.4 Upon detection of a
Of electric current by operating the transistor in order. Wiper volume position wiper
running second or more, contact the front watch- Shah of combination switch ON become INPUT1 When OUTPUT2 Circuit is conducting of. The driver
control unit to the wiper amplifier LO To send the operation. Washer switch OFF If the driver control unit detects that became a state, LO About the
Mist working
• The wiper switch MIST When position, wiper LO The operation One Times done and then stop.
Overview
• The driver control unit reads the state of the combination switch (lamps, wiper), based on the results, head lamps, to control the related systems,
such as wiper.
• The driver control unit Five One of the output terminal ( OUTPUT1 ~ Five )When Five One of the input terminal ( INPUT1 ~ Five In combination of), maximum Twenty Read the diagnostic
DESCRIPTION OF OPERATION
• The driver control unit is always input terminal ( INPUT1 ~ Five And it outputs a power supply voltage from). At this time, the output terminal ( OUTPUT1 ~ Five )
WW - 8
Front wiper washer system
• The switch of any one (or more) ON When the voltage of the input terminal changes corresponding to the switch, an interface in a driver control
unit detects that condition, the driver control unit switches
ON It is determined that the.
SKIA2833J
E
Combination switch operation table
• The driver control unit reads the operating state of the combination switch in the combination shown in the table below.
I
SKIA2834J
Reference: Head lamp Two We have set the system of the switch.
• The driver control unit OUTPUT3 Of the transistor ON When, INPUT1 Front wiper switch when it detects that the voltage has changed in LO Determined
to be a position, front wiper to the wiper amplifier LO To send an actuation signal.
WW
WW - 9
Front wiper washer system
• The driver control unit again OUTPUT3 When was activated of the transistor, INPUT1 Front wiper when it detects that the voltage has changed in LO
It recognizes that operation is continued.
SKIA2965J
Note: Each OUTPUT Transistor terminals 10ms Operating in the interval. Thus, the switch ON The electrical load from and to
There delay occurs in up to operate. However, the delay is a very small time positions which can not be recognized by the human senses.
Mode of operation
The combination switch reading function there is a mode of operation of the following.
1. Normal time
- When the driver control unit is non-sleep state, OUTPUT ( One ~ Five ) Is of the terminal each 10ms Each time
ON-OFF Operate.
2. Sleep state
- When the driver control unit is in the sleep state, OUTPUT1 as well as Two Of the transistor to stop the output, a low current consumption mode. OUTPUT ( Three ~
Five ) Is 10ms Each time ON-OFF Actuated, it accepts only the input of the light switch system.
SKIA2837J
Intermittent working
Ass volume between the combination switch is intermittent pause time of the wiper One , Intermittent volume Two , Intermittent volume Three of Three And One of the switch BCM A
vehicle speed signal from the (body CAN Determine by a combination of a communication).
WW - 10
Front wiper washer system
Combination switch
Ass interval between the wiper volume position
Intermittent volume 1 between the ass volume Two Intermittent volume Three
Wiper volume 1 ON ON ON
small
During the reading function of the combination switch ass volume One , Two , Three of ON , OFF State the driver Control Ruyunitto will detect.
D
Wiper volume when the driver control unit is the combination switch is in a state of the following One It will assume.
JA
WW
PKIA1395J
WW - 11
Front wiper washer system
SW )
CAN Vehicle speed signal and the key received by the communication SW of ON Body signals CAN Driver communication C / U To
BCM
send to.
driver C / U Of front wiper LO , HI as well as INT To send an activation signal to the wiper amplifier.
Wiper amplifier LO , HI as well as INT To send the wiper motor driving signal by the actuation signal.
TKWA0481J
WW - 12
Front wiper washer system
Driver control unit input and output signal reference value JKS00CV2
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW
Nine INPUT1 C
Ten INPUT2 11
17 B / CAN L - - -
Eighteen B / CAN H - - -
25 OUTPUT 2
SKIA2656J
43 Earth ON - about 0
G
BCM Input and output signal reference value JKS00CV3
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW H
One BAT Power supply OFF - about Twelve
49 B / CAN L - - - I
52 CAN H - - -
53 Earth ON - about 0
63 B / CAN H - - - JA
65 CAN L - - -
WW
Measurement condition
Terminal
Signal name Key Reference value( V)
number Operation or state
SW
WW - 13
Front wiper washer system
Measurement condition
Terminal
Signal name Key Reference value( V)
number Operation or state
SW
Two Wiper motor drive signal ON Wiper SW LO From HI about Twelve About from 0
WW - 14
Front wiper washer system
1. The contents of to get the information from your failure to confirm the request.
2. To grasp the system overview. " System Overview "( WW-4 page ) To see.
3. To verify the configuration status of the system. " Before diagnosis inspection "( WW-15 page ) To see.
Five. Communicate diagnosis. " BCS Body Control System " "Communication Diagnostics" ( BCS-31 page ) To see.
6. From the phenomenon by fault diagnosis table, to repair or replace the cause of the failure. " Another fault diagnosis Chart phenomenon " (WW-17 page) To see.
C
7. Again, performing the operation check. If there is abnormal Two To implement the inspection again from the procedure.
8. Exit.
• CONSULT - In Ⅱ and the front display can be set change of the vehicle speed sensing wiper.
select a
OFF -
F
CONSULT-II Function of JKS00CV8
CONSULT - Ⅱ is BCM from CAN Receiving data by the communication line, a combination of transmission of the command, there is another work support display functions each site.
G
BCM Diagnostic site inspection item, diagnosis mode Content
Beauty CONSULT- To connect the Ⅱ. For more information separate volume " CONSULT- Ⅱ instruction manual
WW - 15
Front wiper washer system
• [ BCM ] If you do not display, "diagnostic system selection" screen after printed out, " CONSULT-II
Note at the time of use "( LAN-4 page ) See.
SKIA2660J
For more information, separate " CONSULT- Ⅱ instruction manual (common) (Supplement One ) (Supplement Two
SKIA2661J
Work support
Vehicle speed sensing wiper setting
Operation procedure
3. Touch the vehicle speed sensing wiper setting] in the "work item selection" screen.
7. Touch [END].
WW - 16
Front wiper washer system
• " The power supply and the ground circuit system of the wiper amplifier "( WW-17 Page ) See.
• " LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
Front wiper is not working • " Front wiper actuation signal system "( WW-19 page ) See. B
• " Front wiper motor system "( WW-20 page ) See.
• " Front wiper motor drive signal line "( WW-21 page )
See.
• Front wiper drive ASSY Mechanical failure.
Front wiper does not return to the stop position " Auto-stop signal system "( WW-22 page ) See. C
• " LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
• " Front wiper actuation signal system "( WW-19 page ) ( LO Referring to the work dynamic signal
Front wiper LO It does not operate only only).
• " Front wiper motor system "( WW-20 page ) See. D
• " Front wiper motor drive signal line "( WW-21 page )
See.
• " LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
• " Front wiper actuation signal system "( WW-19 page ) ( HI Referring to the actuation signal E
Front wiper HI It does not operate only only).
• " Front wiper motor system "( WW-20 page ) See.
• " Front wiper motor drive signal line "( WW-21 page )
See.
" LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
It does not operate the front wiper is intermittent only F
• " LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
You can not ass volume adjustment between the front wiper
• " Auto-stop signal system "( WW-22 page ) See.
• Confirmation of setting change function "Diagnosis before inspection" ( WW-15 page ) See. G
It is not carried out the control of the speed of the intermittent time • " BCS Body Control System " "Communication Diagnostics "
(BCS-31 page ) See.
Wiper is not wiped off at the time of the front washer working " LT Lighting systems " "Combination switch
inspection"( LT-120 page ) See.
" LT Lighting systems " "Lamp, abnormal operation movement of the wiper" ( LT-123 H
Front wiper is abnormal operation
page ) See.
The power supply and the ground circuit system of the wiper amplifier JKS00CVA
I
1. Fuse inspection
• Blow below the fuse is to check whether or not there.
# 74 Twenty A IPDM E / R
Fuse position " PG Power supply and ground circuit components "on "Terminal sequence" ( PG-3 page ) See.
WW
Inspection results OK Or?
OK » Two What.
WW - 17
Front wiper washer system
2. Front wiper relay vehicle side harness connector One , Five Ban terminal
Terminal
Measurement condition Voltage( V)
(+) (-)
SKIA2949J
OK » Three What.
2. Front wiper relay vehicle side harness connector Two Ban terminal ~ Bo
OK » Four What.
OK » Five What.
SKIA2951J
WW - 18
Front wiper washer system
2. Front wiper relay vehicle side harness connector Three Ban terminal ~ Wa
Ipaanpu vehicle side harness connector Five To check the continuity between the turn terminal.
B
Three ~ Five : Yes conduction
OK » Six What.
C
NG Her between »front wiper relay - wiper amplifier SKIA2952J
grounding.
E
Inspection results OK Or?
OK »Normal.
To management.
F
SKIA2953J
G
1. LO Actuation signal circuit inspection
Amplifier vehicle side harness connector Six To check the continuity between the turn terminal.
I
Inspection results OK Or?
OK » Two What.
SKIA2954J
To.
JA
WW
WW - 19
Front wiper washer system
driver C / U Vehicle side harness connector Six Ban terminal ~ wiper amplifier vehicle side harness connector Seven
OK » Three What.
To.
SKIA2955J
Nectar Five , Six To check the voltage between the turn pin-body earth.
Terminal
Measurement condition Voltage( V)
(+) (-)
OK »Normal.
NG »Driver C / U To exchange.
Terminal
Operation of the motor
(+) (-)
OK »Normal.
WW - 20
Front wiper washer system
Child-wiper amplifier vehicle side harness connector 1, 2, 3 To check the continuity between the turn
terminal.
C
One ~ One : Yes conduction
NG »Repair the harness between the front wiper motor - wiper amplifier.
3. To operate the wiper switch, the front wiper motor vehicle side F
Harness connector One , Three The voltage across the terminals turn-body earth to point inspection.
Terminal
Measurement condition Voltage( V)
G
(+) (-)
One
Body earth Wiper SW LO about Twelve SKIA2959J
OK »Normal.
JA
WW
WW - 21
Front wiper washer system
2. The wiper switch LO The position, the driver C / U Vehicle side harness
Scan connector Twenty To check the voltage between the turn pin-body earth.
Terminal
Measurement condition Voltage( V)
(+) (-)
Twenty body
Earth wiper SW LO about Twelve And about 0 The provision for Return Ri
SKIA2960J
OK » Five What.
NG » Two What.
3. Front wiper motor vehicle side harness connector Five Ban terminal ~
Wiper amplifier vehicle side harness connector Four To check the continuity between the turn terminal.
OK » Three What.
NG »Repair the harness between the front wiper motor - wiper amplifier.
2. Front wiper relay vehicle side harness connector Three Ban terminal-off
Ron To wiper motor vehicle side harness connector Six To check the continuity between the turn
terminal.
OK » Four What.
WW - 22
Front wiper washer system
Front wiper motor vehicle side harness connector Four To check the continuity between the
B
Inspection results OK Or?
2. Front wiper motor vehicle side harness connector Five Ban terminal ~
driver C / U Vehicle side harness connector Twenty To check the continuity between the turn terminal.
E
Five ~ Twenty : Yes conduction
OK »Normal.
Cause treatment
Oil film adhesion of the wax and the like to the window glass • Use the oil film up agents, and the like, to remove the oil film of the glass surface.
surface. • Oil of the wiper refill (wiper rubber) portion is also removed.
• Remove the blade from the wiper arm, to check the gap between the glass surface of the end of the arm and the wiper
stop position in the thickness gauge. Gap: about 0.6mm
I
• Adjustment, the arm tip Two Scissors using the
JA
ELH0173D
WW
Reference: Oil film up and peeling of the glass coating agent Nissan original glass treatment set ( KA500 - 89902 Phrase)
You can use the lean all, dropped Nissan genuine strong oil film ( KA200 - 89921 ) May be used.
WW - 23
Front wiper washer system
removal
1. The wiper switch ON From to and, by operating the wiper motor OFF To (auto stop).
2. Open the hood and remove the nut cover wiper arm mounting nut (each One Remove the pieces).
3. Lift the driver's seat side wiper arm, remove the wiper arm from the vehicle.
Four. Lift the passenger side wiper arm to close the hood, remove the wiper arm from the vehicle.
attachment
1. As the arm attachment sites cleaning and mounting nut is hard to loose, as shown in FIG.
To.
ELH0717D
2. As the center tip of the width of the wiper blade comes to the position shown in the figure, the word
The Lee par blade down on the surface of the glass. (When the blade tip Conform to
the marking that has been set in the blade set position of the black print set is easy.)
Torque with a wiper arm mounting nut tightening ( Nm { Kg- m}): 16.7 ~ 22.6 { 1.7
~ 2.3 }
Four. To inject the washer liquid. The wiper switch ON After actuating the wiper motor to OFF (An auto
To top).
Five. Wiper blades to make sure that you are stopped at the position shown in FIG.
Detail is, " Removing the front wiper arm, mounting "( WW-24 page ) See.
WW - 24
Front wiper washer system
PKIA1397J
removal
1. Remove the front wiper arm. Detail is "Removing the front wiper arm, mounting" ( WW-24 page )
See. F
2. Remove the cowl top cover. " EI Exterior and interior "of "Cowl top" ( EI-13 page ) See.
G
Four. Front wiper motor link mounting bolts ( Five Remove the book), the ring
Five. Take the wiper link from the wiper frame and the motor arm
remove.
H
6. Wiper motor mounting bolts ( Three Remove the book), or wiper frame
PKIA1398J
I
attachment
1. The wiper motor connected to the vehicle side connector, the wiper switch ON Or by operating the wiper motor in the
WW
Wiper motor mounting bolt tightening torque ( Nm { kg- m}): 5.0 ~ 6.0 { 0.5 ~ 0.61
}
Four. Attaching the wiper link to the wiper frame and the motor arm.
L
Five. Attaching the wiper motor link to the vehicle.
WW - 25
Front wiper washer system
Wiper motor ASSY With mounting bolt tightening torque ( Nm { kg- m}): 3.8 ~ 5.1 { 0.39
~ 0.52 }
6. The wiper motor link connected to the vehicle side connector, the wiper switch ON To, operate the wiper motor
The wiper switch from by OFF To (auto stop).
7. Attach the cowl top cover. " EI Exterior and interior "of "Cowl top" ( EI-13 page ) See.
8. Attaching the wiper arm. Detail is "Removing the front wiper arm, mounting" ( WW-24 page )
Caution : • Dropping the wiper motor, it does not interfere with other parts.
• Note the grease state of the mating portion of the motor arm and the wiper link (retainer portion), to apply the grease as needed. Nisan MP
WW - 26
Front wiper washer system
A 262 439 80
C
PKIA1399J
Injection position adjustment, insert the needle or the like is carried out by moving up and down, left and right to the injection holes.
PKIA1400J
JA
WW
L
PKIA1401J
WW - 27
Front wiper washer system
removal
2. Unlock the clip the nozzle elevation point side by pulling in the direction of the arrow, the nozzle
PKIA1402J
When you blew in the forward direction (the injection hole side) you can ventilation, to check and not be able to
PKIA1403J
attachment
3. Perform a nozzle injection position adjustment. " Injection position adjustment of the front washer nozzles "( WW-27 page ) See.
Caution : Since the point There are different, it mounted so as not to mistake the left and right of the nozzle.
Detail is" LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
3. Figure the direction of the arrow to nail ( Two Wiper washer scan while pressing the point)
Pull the switch on the passenger side door direction, to the outside to take than the spiral cable.
PKIA1404J
WW - 28
Front wiper washer system
removal
1. Washer fluid inlet side of the screw ( One Washer to remove the book)
PKIA1405J
2. Remove the front side of the right fender protector. " EI Exterior
Interior "of "Fender protector" ( EI-15 page ) See. D
E
Five. Remove the washer hose, remove the washer tank from vehicle
It is.
PKIA1406J
F
attachment
Mounting with caution in the following tasks, carried out in the reverse order of removal.
Caution : After installation, put the water until the washer tank inlet top surface, to make sure that there is no water leakage.
Washer tank mounting screw tightening torque ( Nm { kg-m }): 3.8 ~ 5.1 { 0.39 ~ 0.52 G
}
H
removal
1. Remove the front side of the right fender protector. " EI Exterior
Interior "of "Fender protector" ( EI-15 page ) See.
JA
PKIA1407J
attachment
Installation work is attention to the work of the following, carried out in the reverse order of removal. WW
Caution : When the washer pump mounting, that twist, etc. of the packing is defunct.
WW - 29
Front wiper washer system
removal
1. IPDM E / R A remove. " PG Power supply and ground circuit components "on
2. Remove the connector of the wiper amplifier, IPDM E / R From the bracket
PKIA1422J
attachment
Installation is carried out in the reverse order of removal.
WW - 30
Rear wiper-washer system
• BCM Key switch ON Body signals CAN Using a communication be sent to the back-door control unit.
• Wiper switch (combination switch) is Five And One of the output terminal Five One of which is constituted by the combination of the input terminals, the
combination state driver control unit terminals when switched on reads.
• The driver control unit is operated and the rear wiper INT To send an activation signal to the back-door control unit. B
• Back door control unit rear wiper operation and INT By the actuation signal to drive the rear wiper motor.
Feature Description
C
System chart
SKIA2968J
G
• The driver control unit rear wiper by the reading function of the combination switch INT But ON Upon detection of the state, the body to the back I
door control unit CAN Rear wiper with communication INT To send an actuation signal.
• Key switch ON Sometimes, the back door control unit rear wiper INT Upon receiving the activation signal, about the rear wiper motor Seven To operate in the second
interval.
JA
Washer interlocking actuation
• The rear washer switch about 0.4 Sec or more ON Then, the rear wiper motor to work.
• The rear washer switch ON → OFF When, rear wiper One Time working to return to the set position. Thereafter, it operates as follows. Set position → Inverted position
(about Two Second pause) → Set position → Inverted position (about Two Second pause) → Set position
WW
• The rear washer switch during intermittent working ON Then prioritize the rear washer switch.
WW - 31
Rear wiper-washer system
DESCRIPTION OF OPERATION
circuit diagram
TKWA0482J
terminal Thirty Of the rear wiper motor through the turn terminal One The power supply voltage is supplied to the turn terminal. at the same time, BCM The body is CAN
Key switch using the communication ON To send a signal to the back-door control unit. The rear wiper switch ON When you position, the contacts of the rear wiper
The driver control unit rear wiper by the reading function of the combination switch ON State and the detection result, body CAN The rear wiper
actuation signal using a communication And transmits it to the back door control unit. Backdoor control unit which receives the rear wiper actuation
signal, the rear wiper motor Four From turn terminal of the back door control unit Ten Grounded in turn terminal, to operate the rear wiper motor.
Contact of the back door switch When the back door is open at the time of rear wiper actuated ON Next, the back door control unit Sixteen Ban
terminal is grounded. Back door control unit recognizes the back door is opened, and to stop the rear wiper motors.
• 20A (# 41 ) From the back door control unit Four Backup power voltage is supplied to turn the terminal. The key switch ON If you, IPDM E / R of One From turn terminal Thirty
Of the rear wiper motor through the turn terminal One The power supply voltage is supplied to the turn terminal. at the same time, BCM The body is CAN Key switch using the
WW - 32
Rear wiper-washer system
The rear wiper switch INT When you position, the contacts of the rear wiper combination switch ON become, INPUT4
When OUTPUT1 Circuit is conducting of.
The driver control unit rear wiper by the reading function of the combination switch ON State and the detection result, body CAN Rear wiper using a
communication INT An actuation signal And transmits it to the back door control unit. Rear wiper INT Backdoor control unit that has received the operation
signal, the rear wiper motor Four From turn terminal of the back door control unit Ten Grounded in turn terminal, about the rear wiper motor Seven To
• 10A (# twenty two ) From the combination switch Fifteen The power supply voltage is supplied to the turn terminal. When the rear wiper switch to the rear washer
position, the combination switch Five Washer motors from turn terminal One Supplying a voltage to turn the terminal, the combination switch Sixteen , 14 Through the C
turn terminal is grounded, washer motors is activated. Washer motor 0.4 Upon detection of a running second or more, the contact point of the combination switch
rear washer is ON become INPUT3 When OUTPUT2 Circuit is conducting of. The driver control unit body CAN Using a communication to send a rear wiper activation
signal to the back door control units. The rear washer switch ON → OFF When, rear wiper One Time working to return to the set position. After that, the sea urchin
working good following. Set position → Inverted position (about Two Second pause) → Set position → Inverted position (about Two Second pause) → Set position D
For more information about the features " Wiper switch reading function of driver control unit " (WW-8 page ) See. F
JA
WW
WW - 33
Rear wiper-washer system
PKIA1408J
Of front wiper LO , HI as well as INT Back door actuation signal C / U Send to.
driver C / U
back door C / U LO , HI as well as INT To rear wiper motor driven by the actuation signal.
WW - 34
Rear wiper-washer system
TKWA0482J
G
Driver control unit input and output signal reference value JKS00CVJ
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW H
Eleven INPUT3
Twelve INPUT4
I
ON Light, turn, wiper OFF
State of
13 INPUT5
SKIA2655J
17 B / CAN L - - - JA
Eighteen B / CAN H - - -
25 OUTPUT 2
WW
ON Light, turn, wiper OFF
26 OUTPUT 1 State of
SKIA2656J
43 Earth ON - about 0 L
WW - 35
Rear wiper-washer system
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW
49 B / CAN L - - -
52 CAN H - - -
53 Earth ON - about 0
63 B / CAN H - - -
65 CAN L - - -
Measurement condition
Terminal
Signal name Key Reference value( V)
number Operation or state
SW
Back door control unit input and output signal reference value JKS00CVM
Measurement condition
Terminal
Signal name Key Reference value( V)
number Operation or state
SW
Five B / CAN L - - -
Six B / CAN H - - -
Nine Rear wiper position detection signal ON Rear wiper SW ON about Twelve And about 0 repeat
issue
WW - 36
Rear wiper-washer system
1. The contents of to get the information from your failure to confirm the request.
2. To grasp the system overview. " System Overview "( WW-31 page ) See.
Four. Communicate diagnosis. " BCS Body Control System " "Communication Diagnostics" ( BCS-31 page ) To see. B
Five. From the phenomenon by fault diagnosis table, to repair or replace the cause of the failure. " Another fault diagnosis Chart phenomenon " (WW-39 page) To see.
6. Again, performing the operation check. If there is abnormal Two To implement the inspection again from the procedure.
C
7. Exit.
JA
WW
WW - 37
Rear wiper-washer system
Five. The key switch ACC West, Ten The rear defogger switch within seconds Ten Press more times.
7. While holding down the rear defogger switch to the lamp lit, the key switch ON When you switch the monitor is activated.
8. On the passenger side setting temperature display unit and the rear air conditioning setting temperature display unit 99 But
Is blinking, and operates the switch monitored switch, left and right map lamp blinks,
the buzzer of the roof control unit is ringing blow.
9. When the following conditions are met to terminate the switch monitor.
Five. Air conditioning OFF Press the switch, to stop the air conditioning.
6. While holding down the vehicle information switch, temperature control dial (right) Ten Within seconds Thirty Click to manipulate or more.
SKIA2767J
WW - 38
Rear wiper-washer system
8. Joystick " switch " When you select a switch monitor cause
To do.
9. On the passenger side setting temperature display unit and the rear air conditioning setting temperature display unit 99 But
Is blinking, and operates the switch monitored switch, left and right map lamp blinks,
the buzzer of the roof control unit is ringing blow.
B
Ten. When the following conditions are met to terminate the switch monitor.
SKIA2771J
E
Switch monitored switch
• " The power supply and the ground circuit system of the rear wiper "( WW-40 page ) G
See.
• " LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
Rear wiper does not return to the stop position " Rear wiper position detection signal line "( WW-42 page ) See.
" LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
Rear wiper switch ON It does not operate only at the time of
I
• " LT Lighting systems " "Inspection of the combination switch" ( LT-120 page ) See.
It does not operate the rear wiper is intermittent only
• " Rear wiper position detection signal line "( WW-42 page ) See.
Wiper is not wiped off at the time of the rear washer working " LT Lighting systems " "Combination switch JA
inspection"( LT-120 page ) See.
Rear wiper does not stop when you open the back door " Back door switch line "( WW-43 page ) See.
" LT Lighting systems " "Lamp, abnormal operation movement of the wiper" ( LT-123
Rear wiper is abnormal operation
page ) See.
WW
WW - 39
Rear wiper-washer system
The power supply and the ground circuit system of the rear wiper JKS00CVQ
1. Fuse inspection
• Blow below the fuse is to check whether or not there.
Fuse position " PG Power supply and ground circuit components "on "Terminal sequence" ( PG-3 page ) See.
OK » Two What.
3. Rear wiper motor vehicle side harness connector One Ban terminal ~ Bo
OK » Three What.
SKIA2969J
NG »The harness between the fuse - rear wiper motor Osamu
To management.
2. back door C / U Vehicle side harness connector Four Ban terminal ~ Body
OK » Four What.
back door C / U Vehicle side harness connector Eleven To check the continuity between the turn pin-body
grounding.
OK »Normal.
To. Fuse
SKIA2971J
WW - 40
Rear wiper-washer system
2. back door C / U And remove the connector of the rear wiper motor.
3. back door C / U Vehicle side harness connector Ten Ban terminal ~ Riyawai
B
Per motor vehicle side harness connector Four To point detects the conduction between the turn terminal.
SKIA2972J
OK » Two What.
NG »Back door C / U To repair the harness between the ~ rear wiper motor.
D
1. back door C / U And connect the connector of the rear wiper motor
To. E
2. The key switch ON To.
3. To operate the rear wiper switch, the back door C / U Vehicle side harness
Scan connector Ten To check the voltage between the turn pin-body earth.
F
Terminal
Measurement condition Voltage( V)
(+) (-)
Ten body
Earth Rear wiper SW OFF about Twelve G
OK »Normal.
2. The connector on the rear wiper motor 12V Voltage added, Meaux
Terminal
Operation of the motor
(+) (-)
OK »Normal.
WW - 41
Rear wiper-washer system
2. The rear wiper switch ON Then, back door C / U Vehicle side hard
Ness connector Nine To check the voltage between the turn pin-body earth.
Terminal
Measurement condition Voltage( V)
(+) (-)
Body earth Rear wiper SW about Twelve And about 0 The provision for
Nine
ON Return Ri
SKIA2975J
OK »Normal.
NG » Two What.
2. Rear wiper motor and the back door C / U Remove the connector.
3. Rear wiper motor vehicle side harness connector Two Ban terminal ~ back
Kudoa C / U Vehicle side harness connector Nine To check the continuity between the turn terminal.
SKIA2976J
OK » Three What.
Rear wiper motor vehicle side harness connector Three To check the continuity between the
SKIA2977J
WW - 42
Rear wiper-washer system
) See.
OK »Normal.
NG »Back door switch inspection" BL Body lock security "of "Back door switch inspection "
(BL-45 page ) See.
C
Corresponding at the time of judder occurrence JKS009XN
treatment
D
Oil film adhesion of the wax and the like to the window glass • Use the oil film up agents, and the like, to remove the oil film of the glass surface.
surface. • Oil of the wiper refill (wiper rubber) portion is also removed.
Reference: Oil film up and peeling of the glass coating agent Nissan original glass treatment set ( KA500 - 89902 Phrase)
You can use the lean all, dropped Nissan genuine strong oil film ( KA200 - 89921 ) May be used.
removal
1. The wiper switch ON From to and, by operating the wiper motor OFF To (auto stop).
3. Lift the wiper arm, remove the wiper arm from the vehicle.
attachment
H
1. Cleaning and mounting nut is hard to loose as shown in the illustration arm attachment site
So. Cause
JA
SKIA0082J
WW
WW - 43
Rear wiper-washer system
2. As the center tip of the width of the wiper blade comes to the position shown in the figure, the word
The Lee par blade down on the surface of the glass. (When the blade tip Conform to
the marking that has been set in the black print of the grade set position set easily.)
- 10 mm
3. The wiper arm nuts ( One Tightening in this), take the nut cover
wear. PKIA1409J
Torque with a wiper arm mounting nut tightening ( Nm { kg-m }): 4.0 ~ 6.0 { 0.41 ~
0.61 }
(Resin arm)
Four. To inject the washer fluid. The wiper switch ON A manner, the actuates the wiper motor OFF (Auto
To stop).
Five. Wiper blades to make sure that you are stopped at the position shown in FIG.
Detail is, " Removing the rear wiper arm, mounting "( WW-43 page ) See.
PKIA1410J
WW - 44
Rear wiper-washer system
removal
2. Remove the rear wiper arm. " Removing the rear wiper arm ,
attachment"( WW-43 page ) See.
B
3. Remove the roof spoiler. " EI Exterior and interior "of "Rufusupoi
Error "( EI-26 page ) See.
Four. Remove the connector of the wiper motor on the back door inside. Rear
View camera mounted on vehicles, remove also the connector of the rear view camera. PKIA1411J
C
Five. Remove the lead wire of a grommet that entered the back door from the wiper motor (for rubber watertight), of the wiper motor
Take out the connector and the connector of the rear view camera (rear view camera mounted on vehicles only).
6. Rear wiper motor mounting screw ( Three Remove the book), remove the rear wiper motor from vehicle.
D
Caution : Dropping the rear wiper motor, it does not interfere with other parts.
attachment
Torque with a wiper motor mounting screw tightening ( Nm { kg-m }): 3.8 ~ 5.1
{ 0.39 ~ 0.52 }
2. The back door of the connector and the connector of the rear view camera of the wiper motor (rear view camera mounted on vehicles only)
F
Add to the through-hole.
3. Fitting of the lead wire grommet (rubber for watertight) to the back door.
Four. The wiper motor connected to the vehicle side connector, the wiper switch ON Or by operating the wiper motor in the
Five. Installing a roof spoiler on the vehicle. " EI Exterior and interior "of "Roof spoiler" ( EI-26 page ) See.
6. Mounting the wiper arm on the vehicle. Detail is " Removing the rear wiper arm, mounting " (WW-43 page ) See.
Torque with a wiper arm mounting nut tightening ( Nm { kg-m }): 4.0 ~ 6.0 { 0.41 ~ 0.61
}
(Resin arm)
I
7. Do the stop position adjustment of the wiper arm.
JA
WW
WW - 45
Rear wiper-washer system
Removal, installation
removal
Arrows in FIG the wiper blade A In direction, unlock further turning from the stopper
position, remove.
PKIA1412J
attachment
A 35 Hundred Hundred
B 35 Hundred Sixty
PKIA1413J
Injection position adjustment, insert the needle or the like is carried out by moving up and down, left and right to the injection holes.
PKIA1414J
Detail is, " Washer hose route "( WW-27 page ) See.
WW - 46
Rear wiper-washer system
removal
1. The washer nozzle in the clockwise direction Ninety ° Turn, or rear spoiler
Et al pull out.
PKIA1415J
When you blew in the forward direction (the injection hole side) you can ventilation, to check and not be able to
D
ventilation when smoked.
PKIA1416J
F
attachment
Mounting is performed in reverse order of removal.
Performing the rear washer jet position adjustment of the nozzle after installation. To perform a nozzle
G
injection position adjustment.
Detail is," LT "Combination switch" in the lighting system. " " Inspection of the combination switch "( LT-120
page ) See. H
Detail is, " Removing the front wiper-washer switch, mounting "( WW-28 page ) See.
I
Removing the rear wiper-washer tank, mounting JKS009XW
Detail is, " Removing the front wiper-washer tank, mounting "( WW-29 page ) See.
JA
Detail is, " Removing the front wiper-washer pump, mounting "( WW-29 page ) See.
WW
WW - 47
Horn
removal
1. Remove the front grille upper. " EI Exterior and interior "of "Front grille" ( EI-11 page ) See.
3. Horn mounting bolts (each One Remove the book), remove the horn from the vehicle.
PKIA1417J
attachment
Mounting note the work of the following, carried out in the reverse order of removal.
Horn mounting bolt tightening torque ( N- m { kg-m }): 5.00 ~ 6.79 { 0.51 ~ 0.69 }
WW - 48
Cigarette lighter
removal
1. Installation lower center panel ASSY A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5
page ) See.
B
2. Pull out the cigarette lighter.
3. Cigarette lighter socket inside of the square hole ( Two From the point) part, cigar
Hold down the claws of the writer Ring remove remove the connector pull the socket to
the front. C
D
PKIA1418J
attachment
Installation is carried out in the reverse order of removal and attention to the work of the following.
E
Caution : Align the cut-out portion of the cigarette lighter ring and the cigarette lighter socket is attached.
JA
WW
WW - 49
Power socket
removal
3. Than the square holes of the inner socket inside, the inner case projection ( Two Place)
While holding down the, remove press the inner socket to the front.
Four. The nails of the inner case with lid ( Two Press the point), Riyakonbine
Remove the inner case with lid than tion lamp lid.
PKIA1420J
attachment
Mounting note the work of the following, carried out in the reverse order of removal.
Caution : Align the groove of the inner case section and the inner socket and rear combination lamps lid with lid, taken
Put Ri.
WW - 50