Professional Documents
Culture Documents
Seat Belts
Seat Belts
SB Seat belt
Notes on belt with car .............................. Two - BCM Input and output reference value ........................................ Twelve C
·Caution .................................................. ................ Two And diagnosis before inspection ................................................. . . . 13
Front seat belt ........................................... Three - Fault diagnosis .................................................. ...... 13
And removal, installation ......................................... Three Second seat belt ..................................... . . . 15
·inspection .................................................. ................ Four - Three Remove point seat belt, mounting ...... Fifteen
D
Seat belt tension reducer .................. Six - Two Remove point seat belt, mounting ...... Sixteen
· Component mounting position ....................................... ...... 6 ·inspection .................................................. ............. 17
·circuit diagram .................................................. ............. Six Third seat belt ............................................ 19
Seat belt warning system .............................. . . . . Ten And removal, installation ................................... . . . 19
· Component mounting position ....................................... . . . . Ten ·inspection .................................................. ............. Twenty E
SB
KA
SB - 1
Notes on work
SRS Air bag, care about the pre-tensioner seat belt with a car JHS000QE
warning : • SRS The configuration of the associated air bag and pretensioner seat belt system components desorption and harness desorption, key
switch OFF In, disconnect the negative battery terminal Three It is carried out after leaving more than minute. (For discharging the electricity stored in the auxiliary power
• The desorption of the components, air tools and power tools, etc. that you do not use.
• SRS Air bag and harness for the pre-tensioner seat belt system is, that you do not repair by solder or the like. In addition, careful attention should be given to
interference with the biting and other parts of the harness.
• SRS That you do not use the electric tester such as circuit testers when the inspection of the air bag and pretensioner seat belt circuit and
separately state. (Working prevention by fine current of the tester)
• The connector of the air bag module and pre-tensioner seat belts, of foreign matter such as a driver plug is not. (Working preventing
electrostatic)
• SRS The airbag and pretensioner seat belt, using the yellow harness connector as identification, and to distinguish from other harness.
• For safety reasons, maintenance work, " SB Seat belt "and" SRS SRS Making reference to the air bag. "
Caution JHS000QF
• When you put in separately the pre-tensioner seat belt is connected to the short-circuit connector to the connector part or, by removing the intermediate harness connector of the
manifold Dokesu part. (Prepare for the unlikely event of the working)
• Pre-tensioner seat belt connector is, that all of the anchor portion seat belt is inserted or removed in the engaged state.
• Pre-tensioner seat belt waste 却要 territory, " SRS SRS Air bag "of "Scrapping process" ( SRS-27 page ) See.
• Exchange and desorption of the pre-tensioner seat belt, also, after you reconnect the pre-tensioner seat belt connector, SRS Normal or inspection to
be using the air bag warning lamp. " SRS SRS Air bag "of "System Inspection" ( SRS-8
page ) See.
• Buckles and the seat belt after the pre-tensioner seat belt working ASSY Do not re-use.
• Oil, grease, cleaning oil, that you do not attach the water, and the like.
• Webbing or has expired, or frayed, are those that are damaged, the seat belt ASSY In exchange.
• Seat belt ASSY The use of genuine parts if you want to exchange the.
SB - 2
Front seat belt
PIIA1823J
E
removal
J
PHIA0187J
8. Remove the mounting screw of the pre-tensioner seat belt retractor, seat belt ASSY A remove.
KA
SB - 3
Front seat belt
Buckle
Four. Remove the anchor bolt, remove the seat belt buckle.
PIIA1828J
attachment
Installation is carried out in the reverse order of removal.
inspection JHS000O5
After collision, the seat belt including a retractor ASSY The mount to inspect all of the sites. In addition, damage to Installing put portion of the seat belt, check that there is no distortion
or the like. If you crash, if you do not want the normal operation or if there is damage, Nissan has recommended the exchange. Result of failure to exchange, there is a possibility that
result in serious personal harm in the event of an accident. In the case of the following to replace the seat belt:
• When the seat belt mounting portion is damaged. (Before installing the new seat belt, the mounting portion damage, to inspect and distortion.)
Pre-inspection
• Key switch in the seat belt is not mounted state ON If the seat belt warning light is on, it turns off and is mounted.
2. Seat belt retractor and the buckle of the anchor bolt Check to make sure that securely tightened.
3. Or the axis of the seat belt shoulder anchor is free to rotate, also, the seat belt adjuster is working properly and
Surely engage or not to confirm.
a. Pull out all the webbing, twist, cut, to check whether there is any other damage.
b. Rewind the webbing. Webbing is confirmed to return to the smooth and completely retractor. Webbing smoothly
When you do not return to the figure, because the dust there is a possibility of the cause, " SEAT BELT , TAPE SET Using "do the work in the following procedure.
2. Securing the webbing of the center pillar belt outlet clip or the like.
3. The webbing and the through hole of the through-anchor, through a thin wire, the webbing through while pulling the wire at both ends by hand
Several times along the surface of the hole, to move up and down to remove the stickies.
Four. Dirt that can not be taken in the wire is, to clean the hole through the webbing in such a clean cloth.
Five. At a position where the webbing of the through-anchor belt through hole is in contact TAPE The paste thing.
Reference: TAPE When the paste is, it is pasted in as there are no wrinkles and sagging.
6. Remove the fixing of the seat belt, to see if the webbing unwinds smoothly.
SB - 4
Front seat belt
c. To wear the seat belt buckle. Firm to see if the seat belt is stopped at that time.
d. The seat belt is removed from the buckle. Release the seat belt, the webbing and the tongue is to make sure to return to the original position.
ELR mechanism
• ELR Mechanism, in an emergency such as a sudden braking by locking the retractor is a mechanism to prevent the stretch webbing more.
B
• The inspection, there is a static inspection and dynamic inspection, or retractor is operating normally, it is determined by performing the following items.
C
Subtracting quickly webbing in the forward direction, the retractor Lock, to make sure that will not be drawn out is the webbing.
warning : • There is nothing to be other cars and obstacles, to perform the following tests in a safe wide place.
• Is paved, dry carried out at the road surface is, wet road surface, road and general road that is not paved, it is not the line in the high-speed road. (Which D
may lead to an accident or injury.)
• Occupant sitting on the seat of the retractor to check the driver and features, the assumption that the retractor is not locked, to prepare for that
reason.
1. Tighten the seat belt of the driver's seat and the other occupants of the seat. E
3. While stopped, locked retractor, the webbing is confirmed that no elongation more. Retractor
If it is not locked, the single item inspection of the retractor.
F
Four. Notifies the undecided of a sudden stop to the passenger, the driver and other passengers on the assumption that the retractor does not lock, the preparation of the order
2. As shown in the figure, do not twist the retractor, tilt the seat belt retractor from the mounted position,
Slowly pull out the webbing.
SHIA0272J J
KA
SB - 5
Seat belt tension reducer
PIIA1983J
PIIA1984J
Tension reducer power supply circuit and the ground system inspection
1. Fuse inspection
• # Eleven To check the fuse.
SB - 6
Seat belt tension reducer
OK » Three What
PIIA2024J
3. Tension reducer - the driver's seat (passenger seat) sheet between the conduction inspection
D
1. Driver's seat and remove the (passenger seat) connector located under the seat.
2. Tension reducer vehicle side connector One Ban terminal - the driver's seat (assistant
's Seat) seat Five ( One ) Perform the conduction inspection between Pin. (): The
OK » Four What
NG »Tension reducer vehicle side connector - the driver's seat (passenger seat) sheet
SB
PIIA2025J
KA
SB - 7
Seat belt tension reducer
Four. Driver's seat (passenger seat) seat - seat belt buckle SW Connector between the conduction inspection
2. Driver's seat (passenger seat) sheet Five ( One ) Pin-seat belt buckle SW
OK » Five What
PIIA1979J
Five. Seat belt buckle SW Connector - the driver's seat (passenger seat) sheet between the conduction inspection
• Seat belt buckle SW 2 Ban terminal - the driver's seat (passenger seat) sheet Seven
( Six ) No. perform terminal conduction inspection of. (): The front
OK » Six What
PIIA1980J
SB - 8
Seat belt tension reducer
• Driver's seat (passenger seat) sheet Seven ( Six ) Th carry out the conduction inspections between the terminals
- body earth.
C
PIIA1981J
2. Sea Insert the seat belt tongue in the seat belt buckle
Seatbelt buckle SW 2 Ban terminal ~ seat belt buckle SW 3 Perform the conduction inspection turn
E
terminal.
State not insert the seat belt tongue: state plugged None conduction
seat belt tongue : Yes conduction
OK »Normal
SB
KA
SB - 9
Seat belt warning system
PIIA1988J
PIIA1989J
SB - 10
Seat belt warning system
System summary
CAN ( Controller Area Network ) And is a serial communication for real-time applications, is a multi-communication of automotive that have excellent data
communication speed and error detection capability. Is equipped with a number of electronic control unit in the car, them of the control unit is not necessarily
running alone, it is working while such cooperation to share the other control units and information. CAN In the communication, each of the control unit Two The
communication lines ( CAN H line, CAN L By connecting a line), It is possible to communicate with a small wiring much information. In addition, transmission and
B
reception of each of the control unit data Was carried out, each control unit reads only the data that need in the data communicating.
2WD car( ABS With car / Adaptive cruise control system without a car)
C
E
SKIA2521J
●: Submit ○: reception
SB
SKIA2523J
●: Submit ○: reception
In Terri
Con
Jefferies Con J
To Adaptive Laser
cement bi
Low cruise VDC / radar
key Yu Natick Steering
Luba control TCS / sensor nickel To reference
IPDM E /
The main signal name / Connection unit ECCS BCM tion angle
C/U valve systems ABS C / R
meter sensor
ASSY U
- A / TC / C/U KA
U One
SB - 11
Seat belt warning system
4WD car( ABS With car / Adaptive cruise control system Mukuruma)
SKIA2525J
●: Submit ○: reception
ABS
Control Aku Intelligent
Combi
Transformer valve Ju er Kiyu knit three
Nesho IPDM E /
The main signal name / Connection unit ECCS fur C / ter C / BCM
C/U Nme ter R
U ASSY - U
Remarks One
A / TC / U
4WD car( VDC With car / Car with adaptive cruise control system)
SKIA2527J
●: Submit ○: reception
Con In Terri
To Jefferies Con
Adaptive Laser
Transformer Low cement bi
cruise VDC / radar
ECC file over C Luba key Yu Natick Steering
control TCS / sensor IPDM E /
The main signal name / Connection unit SC / /U valve BCM nickel tion angle
systems ABS C / R
U ASS To Reference meter sensor
U
Y- One
C/U
A / TC
/U
Measurement condition
Terminal number Signal name Reference value
Key SW Operation or state
SB - 12
Seat belt warning system
1. Fuse inspection
• Blow to the components of the fuse of the following to check whether or not there.
B
Caution : Fuse number " PG Power supply and ground circuit components "on "Fuses and fusible links" ( PG-3 page )
See.
OK »Normal D
E
Seat belt warning lamp is not lit
page ) reference.
OK » Two What
G
NG »Combination meter exchange
2. BCM self-diagnosis
• BCM Perform a self-diagnosis. " BCS Body Control System " " CONSULT- According to the Ⅱ CAN Communication inspection " (BCS-29 SB
page ) reference.
OK » Three What
NG » BCM Replacement I
KA
SB - 13
Seat belt warning system
3. BCM Between the connector - the driver's seat connector conduction inspection
2. Seat belt buckle under the driver's seat SW Remove the connector.
3. BCM Vehicle side harness connector 28 Ban terminal - the driver's seat vehicle side
OK » Four What
NG » BCM The vehicle-side connector - the driver's seat vehicle side harness
PIIA1985J
• Driver's seat connector Seven Inspect the conduction of turn terminal and the body earth.
OK » Five What
PIIA1986J
State not insert the seat belt tongue: state inserting the no seat belt
tongue conduction: Yes conduction
OK »Normal
SB - 14
Second seat belt
PIIA1824J
E
removal
Retractor unit
6. Remove the screw and anchor bolts that attach the seat belt retractor, seat belt ASSY The Remove
It is.
SB
Buckle
attachment
Installation is carried out in the reverse order of removal.
KA
SB - 15
Second seat belt
PIIA1825J
PIIA1826J
removal
1. Remove the second sheet. " SE Sheet "of "Removing, mounting" ( SE-21 page ) See.
2. Remove the seat back and the seat cushion. " SE Sheet "of "Decomposition of the seat back, the assembly" ( SE-21 Page
Di ) , " Decomposition of the seat cushion, the assembly "( SE-24 page ) See.
3. Remove the anchor bolt, remove the seat belt buckles and the seat belt tongue.
attachment
SB - 16
Second seat belt
inspection JHS000QB
After the collision, the retractor unit, seat belt anchor portion, damage the floor anchor portion and the outer anchor portion, boiled is possible to check that there is no such
look. Nissan cases as described below, and recommend replacement because it may result in serious personal harm.
• ELR Is, in the event of an emergency, such as sudden braking by locking retractor, is a mechanism that as the webbing is not pulled out any more.
• The three-point seat belt (outside seat) is, ALR There is a (child seat securing mechanism) mechanism, to use when Keru Attach the child seat. ALR Mechanism D
is to function as fully pull out the webbing, and return the webbing little by little, to lock in a particular position, so do not pull out the webbing is it more.
• The inspection, there is a static inspection and dynamic inspection, or retractor is operating normally, it is determined by performing the following items.
E
Subtracting quickly webbing in the forward direction, the retractor Lock, to make sure that will not be drawn out is the webbing.
• Is paved, dry carried out at the road surface is, wet road surface, road and general road that is not paved, it is not carried out in the high-speed road.
(Which may lead to an accident or injury.)
• Occupant sitting on the seat of the retractor to check the driver and features, the assumption that the retractor is not locked, to prepare G
for that.
1. Tighten the seat belt of the driver's seat and the other occupants of the seat.
Four. While stopped, locked retractor, the webbing is confirmed that no pull out any more. Retractor
But unless you lock, the single item inspection of the retractor. I
1. Pull out all the webbing from the retractor until the "clicks into place".
J
2. When you back little by little the webbing, or the operation sound as the "tick" is heard.
3. When you try to pull out the webbing, the webbing is locked, or will not be drawn out any more.
Four. When we returned all of the webbing, ALR Whether the mode is canceled.
KA
SB - 17
Second seat belt
2. As shown in the figure, do not twist the retractor, tilt the seat belt retractor from the position of the in-vehicle mounted state,
Slowly pull out the webbing.
PHIA0189J
SB - 18
Third seat belt
G
PIIA1827J
removal
Retractor unit
SB
1. Remove the anchor cover.
Five. Remove the rear side finisher lower. " EI Exterior and interior "of "Removing, mounting" ( EI-29 page ) See.
6. Remove the screw and anchor bolts that attach the seat belt retractor, seat belt ASSY The Remove
J
It is.
1. Remove the third seat. " SE Sheet "of "Removing, mounting" ( SE-29 page ) See.
KA
2. Remove the seat back and the seat cushion. " SE Sheet "of "Decomposition of the seat back, the assembly" ( SE-29 Page
Di ) , " Decomposition of the seat cushion, the assembly "( SE-31 page ) See.
3. Remove the anchor bolt, remove the seat belt buckles and the seat belt tongue.
L
SB - 19
Third seat belt
attachment
Installation is carried out in the reverse order of removal.
inspection JHS000QD
After the collision, the retractor unit, seat belt anchor portion, the hinge anchor portion and the outer anchor portion damage, to check whether there is no such as seen
boiled. Nissan cases as described below, and recommend replacement because it may result in serious personal harm.
• ELR Is, in the event of an emergency, such as sudden braking by locking retractor, it is a mechanism for so Eubingu is not pulled out any more.
• The three-point seat belt (outside seat) is, ALR There is a (child seat securing mechanism) mechanism, to use when Keru Attach the child seat. ALR Mechanism
is to function as fully pull out the webbing, and return the webbing little by little, to lock in a particular position, so do not pull out the webbing is it more.
• The inspection, there is a static inspection and dynamic inspection, or retractor is operating normally, it is determined by performing the following items.
Subtracting quickly webbing in the forward direction, the retractor Lock, to make sure that will not be drawn out is the webbing.
warning : • There is nothing to be other cars and obstacles, to perform the following tests in a safe wide place.
• Is paved, dry carried out at the road surface is, wet road surface, road and general road that is not paved, it is not carried out in the high-speed road.
(Which may lead to an accident or injury.)
• Occupant sitting on the seat of the retractor to check the driver and features, the assumption that the retractor is not locked, to prepare
for that.
1. Tighten the seat belt of the driver's seat and the other occupants of the seat.
3. It notifies the undecided of a sudden stop to the passenger, the driver and other passengers on the assumption that the retractor does not lock, preparation for the
Four. While stopped, locked retractor, the webbing is confirmed that no pull out any more. Retractor
But unless you lock, the single item inspection of the retractor.
1. Pull out all the webbing from the retractor until the "clicks into place".
2. When you back little by little the webbing, or the operation sound as the "tick" is heard.
3. When you try to pull out the webbing, the webbing is locked, or will not be drawn out any more.
Four. When we returned all of the webbing, ALR Whether the mode is canceled.
SB - 20
Third seat belt
2. As shown in the figure, do not twist the retractor, tilt the seat belt retractor from the position of the in-vehicle mounted state,
Slowly pull out the webbing.
PHIA0189J
SB
KA
SB - 21
Third seat belt
SB - 22