Professional Documents
Culture Documents
Patrick C. Mackey
President, Mercury Marine, Fond du Lac, WI USA
European Regulations Contact:
Product Environmental Engineering Department, Mercury Marine,
Fond du Lac, WI USA
© 2004 Mercury Marine
i
EPA Emissions Regulations
Outboards manufactured by Mercury Marine in the United States are
certified to the United States Environmental Protection Agency as
conforming to the requirements of the regulations for the control of air
pollution from new outboard motors. This certification is contingent on
certain adjustments being set to factory standards. For this reason, the
factory procedure for servicing the product must be strictly followed and,
wherever practicable, returned to the original intent of the design.
Maintenance, replacement, or repair of the emission control devices and
systems may be performed by any marine engine repair establishment
or individual.
Engines are labeled with an Emission Control Information decal as
permanent evidence of EPA certification.
WARNING
The engine exhaust from this product contains chemicals known to the
state of California to cause cancer, birth defects or other reproductive
harm.
Thank You
for your purchase of one of the finest outboards available. You have
made a sound investment in boating pleasure. Your outboard has been
manufactured by Mercury Marine, a world leader in marine technology
and outboard manufacturing since 1939. These years of experience
have been committed to the goal of producing the finest quality
products. This led to Mercury Marine's reputation for strict quality
control, excellence, durability, lasting performance and being the best at
providing after the sale support.
Please read this manual carefully before operating your outboard. This
manual has been prepared to assist you in the operation, safe use and
care of your outboard.
All of us at Mercury Marine took pride in building your outboard and wish
you many years of happy and safe boating.
Again, thank you for your confidence in Mercury Marine.
ii
Warranty Message
The product you have purchased comes with a limited warranty from
Mercury Marine, the terms of the warranty are set forth in the Warranty
Information Section of this manual. The warranty statement contains a
description of what is covered, what is not covered, the duration of
coverage, how to best obtain warranty coverage, important disclaimers
and limitations of damages, and other related information. Please review
this important information.
The description and specifications contained herein were in effect at the
time this manual was approved for printing. Mercury Marine, whose
policy is one of continued improvement, reserves the right to discontinue
models at any time, to change specifications, designs, methods, or
procedures without notice and without incurring obligation.
Mercury Marine, Fond du Lac, Wisconsin U.S.A.
Litho in U.S.A.
© 2004, Mercury Marine
Mercury, Mercury Marine, MerCruiser, Mercury MerCruiser, Mercury
Racing, Mercury Precision Parts, Mercury Propellers, Mariner,
Quicksilver, #1 On The Water, Alpha, Bravo, Pro Max, OptiMax,
Sport-Jet, K-Planes, MerCathode, RideGuide, SmartCraft, Zero Effort, M
with Waves logo, Mercury with Waves logo, and SmartCraft logo are all
registered trademarks of Brunswick Corporation. Mercury Product
Protection logo is a registered service mark of Brunswick Corporation.
Mercury Premier Service
Mercury evaluates the service performance of its dealers and assigns its
highest rating of "Mercury Premier" to those demonstrating an
exceptional commitment to service.
Earning a Mercury Premier Service rating means a dealer:
• Achieves a 12 month service CSI (Customer Satisfaction Index)
score above the national average.
• Possesses all necessary service tools, test equipment, manuals and
parts books.
• Employs at least one Certified or Master technician.
• Provides timely service for all Mercury Marine customers.
• Offers extended service hours and mobile service, when appropriate.
• Uses, displays and stocks adequate inventory of genuine Mercury
Precision Parts.
• Offers a clean, neat shop with well organized tools and service
literature.
iii
TABLE OF CONTENTS
WARRANTY INFORMATION
Transfer Of Warranty................................................................................ 1
Warranty Registration United States And Canada................................... 1
Warranty Registration Outside The United States And Canada............... 2
Four Stroke Outboard Limited Warranty................................................... 3
3 Year Limited Warranty Against Corrosion............................................. 6
Warranty Coverage And Exclusions......................................................... 9
California Emissions Limited Warranty................................................... 11
Star Label............................................................................................... 16
GENERAL INFORMATION
Boater's Responsibilities......................................................................... 18
Before Operating Your Outboard............................................................ 18
Boat Horsepower Capacity..................................................................... 18
High-Speed And High-Performance Boat Operation.............................. 19
Outboard Remote Control Models ......................................................... 19
Remote Steering Notice.......................................................................... 20
Lanyard Stop Switch............................................................................... 21
Protecting People In The Water.............................................................. 23
Passenger Safety Message - Pontoon Boats And Deck Boats.............. 24
Wave And Wake Jumping...................................................................... 25
Impact With Underwater Hazards........................................................... 26
Safety Instructions For Hand Tilled Outboards....................................... 27
Exhaust Emissions................................................................................. 27
Selecting Accessories For Your Outboard.............................................. 29
Safe Boating Suggestions...................................................................... 29
Recording Serial Number....................................................................... 31
40/50/60 4-Stroke Specifications............................................................ 31
Component Identification........................................................................ 33
INSTALLATION
Installing Outboard.................................................................................. 34
Propeller Selection.................................................................................. 35
TRANSPORTING
iv
TABLE OF CONTENTS
Transporting Portable Fuel Tanks.......................................................... 36
Gasoline Recommendations................................................................... 38
Filling Fuel Tank..................................................................................... 39
Engine Oil Recommendations................................................................ 40
Checking And Adding Engine Oil............................................................ 40
OPERATION
MAINTENANCE
Outboard Care........................................................................................ 65
EPA Emissions Regulations................................................................... 65
Inspection And Maintenance Schedule.................................................. 66
Flushing The Cooling System................................................................. 68
Top Cowl Removal And Installation........................................................ 69
Exterior Care........................................................................................... 69
Battery Inspection .................................................................................. 69
v
TABLE OF CONTENTS
Fuel System............................................................................................ 70
Steering Link Rod Fasteners.................................................................. 71
Corrosion Control Anode........................................................................ 73
Propeller Replacement - 87.3 mm(3 - 7/16 in.) Diameter Gearcase...... 73
Propeller Replacement - 108 mm (4 - 1/4 in.) Diameter Gearcase........ 76
Spark Plug Inspection And Replacement............................................... 79
Fuse Replacement.................................................................................. 80
Timing Belt Inspection............................................................................ 81
Lubrication Points................................................................................... 82
Checking Power Trim Fluid..................................................................... 84
Changing Engine Oil .............................................................................. 84
Gearcase Lubrication - For 87.3 mm(3-7/16 in.) Diameter Gearcase.... 86
Gearcase Lubrication - For 108 mm(4 - 1/4 in.) Diameter Gearcase..... 88
Submerged Outboard............................................................................. 89
STORAGE
Storage Preparation................................................................................ 90
Protecting External Outboard Components............................................ 91
Protecting Internal Engine Components................................................. 91
Gearcase................................................................................................ 91
Positioning Outboard For Storage.......................................................... 91
Battery Storage....................................................................................... 91
TROUBLESHOOTING
Starter Motor Will Not Crank The Engine (Electric Start Models)........... 92
Engine Will Not Start............................................................................... 92
Engine Runs Erratically.......................................................................... 92
Performance Loss................................................................................... 93
Battery Will Not Hold Charge.................................................................. 93
vi
TABLE OF CONTENTS
MAINTENANCE LOG
Maintenance Log.................................................................................... 97
vii
viii
WARRANTY INFORMATION
Transfer Of Warranty
The limited warranty is transferable to a subsequent purchaser, but only
for the remainder of the unused portion of the limited warranty. This will
not apply to products used for commercial applications.
To transfer the warranty to the subsequent owner, send or fax a copy of
the bill of sale or purchase agreement, new owner’s name, address and
engine serial number to Mercury Marine’s warranty registration
department.
Mercury Marine
Attn: Warranty Registration Department
W6250 W. Pioneer Road
P.O. Box 1939
Fond du Lac, WI 54936-1939
920-929-5054
Upon processing the transfer of warranty, Mercury Marine will send
registration verification to the new owner of the product by mail.
There is no charge for this service.
For products purchased outside the United States and Canada, contact
the distributor in your country, or the Mercury Marine Service Office
closest to you.
1
WARRANTY INFORMATION
2. To be eligible for warranty coverage, the product must be registered
with Mercury Marine. At the time of sale, the dealer should complete
the warranty registration and immediately submit it to Mercury
Marine via MercNET, E-mail, or mail. Upon receipt of this warranty
registration, Mercury Marine will record the registration.
3. Upon processing the warranty registration, Mercury Marine will send
registration verification by mail to the purchaser of the product. If this
registration verification is not received within 30 days, please contact
your selling dealer immediately. Warranty coverage is not effective
until your product is registered with Mercury Marine.
2
WARRANTY INFORMATION
IMPORTANT: Registration lists must be maintained by the factory and
dealer in some countries by law. It is our desire to have ALL products
registered at the factory should it ever be necessary to contact you.
Make sure your dealer/distributor fills out the warranty registration card
immediately and sends the factory copy to the Marine Power
International Service Center for your area.
5. For further information concerning the Warranty Registration Card
and its relationship to Warranty Claim processing, refer to the
International Warranty.
3
WARRANTY INFORMATION
CONDITIONS THAT MUST BE MET IN ORDER TO OBTAIN
WARRANTY COVERAGE: Warranty coverage is available only to retail
customers that purchase from a Dealer authorized by Mercury Marine to
distribute the product in the country in which the sale occurred, and then
only after the Mercury Marine specified pre-delivery inspection process
is completed and documented. Warranty coverage becomes available
upon proper registration of the product by the authorized dealer.
Inaccurate warranty registration information regarding recreational use,
or subsequent change of use from recreational to commercial (unless
properly re-registered) may void the warranty at the sole discretion of
Mercury Marine. Routine maintenance outlined in the Operation and
Maintenance Manual must be timely performed in order to maintain
warranty coverage. Mercury Marine reserves the right to make warranty
coverage contingent upon proof of proper maintenance.
WHAT MERCURY WILL DO: Mercury's sole and exclusive obligation
under this warranty is limited to, at our option, repairing a defective part,
replacing such part or parts with new or Mercury Marine certified
re-manufactured parts, or refunding the purchase price of the Mercury
product. Mercury reserves the right to improve or modify products from
time to time without assuming an obligation to modify products
previously manufactured.
HOW TO OBTAIN WARRANTY COVERAGE: The customer must
provide Mercury with a reasonable opportunity to repair, and reasonable
access to the product for warranty service. Warranty claims shall be
made by delivering the product for inspection to a Mercury dealer
authorized to service the product. If purchaser cannot deliver the product
to such a dealer, written notice must be given to Mercury. We will then
arrange for the inspection and any covered repair. Purchaser in that
case shall pay for all related transportation charges and/or travel time. If
the service provided is not covered by this warranty, purchaser shall pay
for all related labor and material, and any other expenses associated
with that service. Purchaser shall not, unless requested by Mercury, ship
the product or parts of the product directly to Mercury. Proof of
registered ownership must be presented to the dealer at the time
warranty service is requested in order to obtain coverage.
U.S. EPA EMISSIONS LIMITED WARRANTY: Consistent with the
obligations created by 40 CFR Part 91, Subpart M, Mercury Marine
provides a two year limited warranty to the retail purchaser, that the
engine is designed, built, and equipped so as to conform at the time of
sale with applicable regulations under section 213 of the Clean Air Act,
and that the engine is free from defects in materials and workmanship
which cause the engine to fail to conform with applicable regulations.
4
WARRANTY INFORMATION
WHAT IS NOT COVERED: This limited warranty does not cover routine
maintenance items, tune ups, adjustments, normal wear and tear,
damage caused by abuse, abnormal use, use of a propeller or gear ratio
that does not allow the engine to run in its recommended wide open
throttle RPM range (see the Operation and Maintenance Manual),
operation of the product in a manner inconsistent with the recommended
operation/duty cycle section of the Operation and maintenance Manual,
neglect, accident, submersion, improper installation (proper installation
specifications and techniques are set forth in the installation instructions
for the product), improper service, use of an accessory or part not
manufactured or sold by us, jet pump impellers and liners, operation with
fuels, oils or lubricants which are not suitable for use with the
product (see the Operation and Maintenance Manual), alteration or
removal of parts, water entering the engine through the fuel intake, air
intake or exhaust system, or damage to the product from insufficient
cooling water caused by blockage of the cooling system by a foreign
body, running the engine out of water, mounting the engine too high on
the transom, or running the boat with the engine trimmed out too far.
Use of the product for racing or other competitive activity, or operating
with a racing type lower unit, at any point, even by a prior owner of the
product, voids the warranty.
Expenses related to haul out, launch, towing, storage, telephone, rental,
inconvenience, slip fees, insurance coverage, loan payments, loss of
time, loss of income, or any other type of incidental or consequential
damages are not covered by this warranty. Also, expenses associated
with the removal and/or replacement of boat partitions or material
caused by boat design for access to the product are not covered by this
warranty.
No individual or entity, including Mercury Marine authorized dealers, has
been given authority by Mercury Marine to make any affirmation,
representation or warranty regarding the product, other than those
contained in this limited warranty, and if made, shall not be enforceable
against Mercury Marine.
For additional information regarding events and circumstances covered
by this warranty, and those that are not, see the Warranty Coverage
section of the Operation and Maintenance Manual, incorporated by
reference into this warranty.
5
WARRANTY INFORMATION
DISCLAIMERS AND LIMITATIONS:
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY
DISCLAIMED. TO THE EXTENT THAT THEY CANNOT BE
DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE LIFE OF THE EXPRESS WARRANTY.
INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED
FROM COVERAGE UNDER THIS WARRANTY. SOME STATES/
COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS,
LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE, AS A
RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO
STATE AND COUNTRY TO COUNTRY.
6
WARRANTY INFORMATION
CONDITIONS THAT MUST BE MET IN ORDER TO OBTAIN
WARRANTY COVERAGE: Warranty coverage is available only to retail
customers that purchase from a Dealer authorized by Mercury Marine to
distribute the product in the country in which the sale occurred, and then
only after the Mercury Marine specified pre-delivery inspection process
is completed and documented. Warranty coverage becomes available
upon proper registration of the product by the authorized dealer.
Corrosion prevention devices specified in the Operation and
Maintenance Manual must be in use on the boat, and routine
maintenance outlined in the Operation and Maintenance Manual must
be timely performed (including without limitation the replacement of
sacrificial anodes, use of specified lubricants, and touch-up of nicks and
scratches) in order to maintain warranty coverage. Mercury Marine
reserves the right to make warranty coverage contingent upon proof of
proper maintenance.
WHAT MERCURY WILL DO: Mercury's sole and exclusive obligation
under this warranty is limited to, at our option, repairing a corroded part,
replacing such part or parts with new or Mercury Marine certified
re-manufactured parts, or refunding the purchase price of the Mercury
product. Mercury reserves the right to improve or modify products from
time to time without assuming an obligation to modify products
previously manufactured.
HOW TO OBTAIN WARRANTY COVERAGE: The customer must
provide Mercury with a reasonable opportunity to repair, and reasonable
access to the product for warranty service. Warranty claims shall be
made by delivering the product for inspection to a Mercury dealer
authorized to service the product. If purchaser cannot deliver the product
to such a dealer, written notice must be given to Mercury. We will then
arrange for the inspection and any covered repair. Purchaser in that
case shall pay for all related transportation charges and/or travel time. If
the service provided is not covered by this warranty, purchaser shall pay
for all related labor and material, and any other expenses associated
with that service. Purchaser shall not, unless requested by Mercury, ship
the product or parts of the product directly to Mercury. Proof of
registered ownership must be presented to the dealer at the time
warranty service is requested in order to obtain coverage.
7
WARRANTY INFORMATION
WHAT IS NOT COVERED: This limited warranty does not cover
electrical system corrosion; corrosion resulting from damage, corrosion
which causes purely cosmetic damage, abuse or improper service;
corrosion to accessories, instruments, steering systems; corrosion to
factory installed jet drive unit; damage due to marine growth; product
sold with less than a one year limited Product warranty; replacement
parts (parts purchased by customer); products used in a commercial
application. Commercial use is defined as any work or employment
related use of the product, or any use of the product which generates
income, for any part of the warranty period, even if the product is only
occasionally used for such purposes.
Corrosion damage caused by stray electrical currents (on-shore power
connections, nearby boats, submerged metal) is not covered by this
corrosion warranty and should be protected against by the use of a
corrosion protection system, such as the Mercury Precision Parts or
Quicksilver MerCathode system and/or Galvanic Isolator. Corrosion
damage caused by improper application of copper base anti-fouling
paints is also not covered by this limited warranty. If anti-fouling
protection is required, Tri-Butyl-Tin-Adipate (TBTA) base anti-fouling
paints are recommended on Outboard and MerCruiser boating
applications. In areas where TBTA base paints are prohibited by law,
copper base paints can be used on the hull and transom. Do not apply
paint to the outboard or MerCruiser product. In addition, care must be
taken to avoid an electrical interconnection between the warranted
product and the paint. For MerCruiser product, an unpainted gap of at
least 38 mm (1.5 in.) should be left around the transom assembly. Refer
to the Operation and Maintenance Manual for additional details.
For additional information regarding events and circumstances covered
by this warranty, and those that are not, see the Warranty Coverage
section of the Operation and Maintenance Manual, incorporated by
reference into this warranty.
8
WARRANTY INFORMATION
DISCLAIMERS AND LIMITATIONS:
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY
DISCLAIMED. TO THE EXTENT THAT THEY CANNOT BE
DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE LIFE OF THE EXPRESS WARRANTY.
INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED
FROM COVERAGE UNDER THIS WARRANTY. SOME STATES/
COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS,
LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE, AS A
RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO
STATE AND COUNTRY TO COUNTRY.
9
WARRANTY INFORMATION
2. Factory installed jet drive units - Specific parts excluded from the
warranty are: The jet drive impeller and jet drive liner damaged by
impact or wear, and water damaged drive shaft bearings as a result
of improper maintenance.
3. Damage caused by neglect, lack of maintenance, accident,
abnormal operation or improper installation or service.
4. Haul out, launch, towing charges, removal and/or replacement of
boat partitions or material because of boat design for necessary
access to the product, all related transportation charges and/or travel
time, etc. Reasonable access must be provided to the product for
warranty service. Customer must deliver product to an authorized
dealer.
5. Additional service work requested by customer other than that
necessary to satisfy the warranty obligation.
6. Labor performed by other than an authorized dealer may be covered
only under following circumstances: When performed on emergency
basis (providing there are no authorized dealers in the area who can
perform the work required or have no facilities to haul out, etc., and
prior factory approval has been given to have the work performed at
this facility).
7. All incidental and/or consequential damages (storage charges,
telephone or rental charges of any type, inconvenience or loss of
time or income) are the owner's responsibility.
8. Use of other than Mercury Precision or Quicksilver parts when
making warranty repairs.
9. Oils, lubricants or fluids changed as a matter of normal maintenance
is customer's responsibility unless loss or contamination of same is
caused by product failure that would be eligible for warranty
consideration.
10. Participating in or preparing for racing or other competitive activity or
operating with a racing type lower unit.
11. Engine noise does not necessarily indicate a serious engine
problem. If diagnosis indicates a serious internal engine condition
which could result in a failure, condition responsible for noise should
be corrected under the warranty.
12. Lower unit and/or propeller damage caused by striking a submerged
object is considered a marine hazard.
13. Water entering engine through the fuel intake, air intake or exhaust
system or submersion.
10
WARRANTY INFORMATION
14. Failure of any parts caused by lack of cooling water, which results
from starting motor out of water, foreign material blocking inlet holes,
motor being mounted too high or trimmed too far out.
15. Use of fuels and lubricants which are not suitable for use with or on
the product. Refer to the Maintenance section.
16. Our limited warranty does not apply to any damage to our products
caused by the installation or use of parts and accessories which are
not manufactured or sold by us. Failures which are not related to the
use of those parts or accessories are covered under warranty if they
otherwise meet the terms of the limited warranty for that product.
11
WARRANTY INFORMATION
DURATION OF COVERAGE: This limited warranty provides coverage
for the components of the emissions control systems of new, 2001
model year (and later) outboards, sold to retail customers in California
for 4 years from either the date the product is first sold, or first put into
service, whichever occurs first, or the accumulation of 250 hours of
engine operation (as determined by the engines hour meter, if any).
Emission related normal maintenance items such as spark plugs and
filters, that are on the warranted parts list (see following) are warranted
up to their first required replacement interval only. (See Maintenance -
Inspection and Maintenance Schedule). The repair or replacement of
parts, or the performance of service under this warranty, does not
extend the life of this warranty beyond its original expiration date.
Unexpired warranty coverage can be transferred to a subsequent
purchaser. (See instructions on transfer of warranty).
HOW TO OBTAIN WARRANTY COVERAGE: The customer must
provide Mercury with a reasonable opportunity to repair, and reasonable
access to the product for warranty service. Warranty claims shall be
made by delivering the product for inspection to a Mercury dealer
authorized to service the product. If purchaser cannot deliver the product
to such a dealer, please notify Mercury Marine and Mercury will then
arrange for the inspection and any covered repair. Purchaser in that
case shall pay for all related transportation charges and/or travel time. If
the service provided is not covered by this warranty, purchaser shall pay
for all related labor and material, and any other expenses associated
with that service. Purchaser shall not, unless requested by Mercury, ship
the product or parts of the product directly to Mercury.
WHAT MERCURY WILL DO: Mercury Marine's sole and exclusive
obligation under this warranty is limited to, at our expense and at our
option, repairing or replacing defective parts with new or Mercury Marine
certified re-manufactured parts, or refunding the purchase price of the
Mercury product. Mercury reserves the right to improve or modify
products from time to time without assuming an obligation to modify
products previously manufactured.
12
WARRANTY INFORMATION
WHAT IS NOT COVERED: This limited warranty does not cover routine
maintenance items, tune ups, adjustments, normal wear and tear,
damage caused by abuse, abnormal use, use of a propeller or gear ratio
that does not allow the engine to run in its recommended wide open
throttle RPM range (see General Information - Specifications), operation
of the product in a manner inconsistent with the recommended operation
procedures, neglect, accident, submersion, improper installation (proper
installation specifications and techniques are set forth in the installation
instructions for the product), improper service, use of an accessory or
part not manufactured or sold by us, jet pump impellers and liners,
operation with fuels, oils or lubricants which are not suitable for use with
the product (see Fuel and Oil), alteration or removal of parts, or water
entering the engine through the fuel intake, air intake or exhaust system.
Use of the product for racing or other competitive activity, or operating
with a racing type lower unit, at any point, even by a prior owner of the
product, voids the warranty.
Expenses related to haul out, launch, towing, storage, telephone, rental,
inconvenience, slip fees, insurance coverage, loan payments, loss of
time, loss of income, or any other type of incidental or consequential
damages are not covered by this warranty. Also, expenses associated
with the removal and/or replacement of boat partitions or material
caused by boat design for access to the product are not covered by this
warranty.
Non-warranty maintenance, replacement, or repair of emission control
devices and systems may be performed by any marine engine repair
establishment or individual. The use of non-Mercury parts for
non-warranty maintenance or repairs will not be grounds for disallowing
other warranty work. The use of add-on (as defined at section
1900 (b)(1) and (b)(10) of Title 13 of the California Code of Regulations)
or modified parts not exempted by the California Air Resources Board
may be grounds for disallowing a warranty claim, at the discretion of
Mercury Marine. Failures of warranted parts caused by the use of a
non-exempted add-on or modified part will not be covered.
COMPONENTS OF THE EMISSIONS CONTROL SYSTEM:
1. Fuel Metering System
a. Carburetor and internal parts (and/or pressure regulator or fuel
injection system)
b. Cold start enrichment system
c. Intake valves
2. Air Induction System
a. Intake manifold
13
WARRANTY INFORMATION
b. Turbocharger systems (where applicable)
3. Ignition System
a. Spark plugs
b. Magneto or electronic ignition system
c. Spark advance/retard system
d. Ignition coil and/or control module
e. Ignition wires
4. Lubrication System (4-Stroke engines excluded)
a. Oil pump and internal parts
b. Oil injectors
c. Oil meter
5. Exhaust system
a. Exhaust manifold
b. Exhaust valves
6. Miscellaneous Items Used in Above Systems
a. Hoses, clamps, fittings, tubing, sealing gaskets or devices, and
mounting hardware.
b. Pulleys, belts and idlers.
c. Vacuum, temperature, check and time sensitive valves and
switches
d. Electronic controls.
14
WARRANTY INFORMATION
CALIFORNIA AIR RESOURCES BOARD EXPLANATION OF
YOUR CALIFORNIA EMISSION CONTROL WARRANTY
STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The California Air
Resources Board is pleased to explain the emission control system
warranty on your 2001 model year and later outboard engine. In
California, new outboard engines must be designed, built and equipped
to meet the State's stringent anti-smog standards. Mercury Marine must
warrant the emission control system on your outboard engine for the
periods of time listed below provided there has been no abuse, neglect
or improper maintenance of your outboard engine.
Your emission control system may include parts such as the carburetor
or fuel injection system, the ignition system, and catalytic converter. Also
included may be hoses, belts, connectors and other emission-related
assemblies.
Where a warrantable condition exists, Mercury Marine will repair your
outboard engine at no cost to you, including diagnosis, parts and labor.
MANUFACTURER'S WARRANTY COVERAGE: Select emission control
parts from model year 2001 and later outboard engines are warranted
for 4 years, or for 250 hours of use, whichever occurs first. However,
warranty coverage based on the hourly period is only permitted for
outboard engines and personal watercraft equipped with appropriate
hour meters or their equivalent. If any emission related part on your
engine is defective under warranty, the part will be repaired or replaced
by Mercury Marine.
OWNER'S WARRANTY RESPONSIBILITIES: As the outboard engine
owner, you are responsible for the performance of the required
maintenance listed in the Maintenance section. Mercury Marine
recommends that you retain all receipts covering maintenance on your
outboard engine, but Mercury Marine cannot deny warranty solely for
the lack of receipts or your failure to ensure the performance of all
scheduled maintenance.
As the outboard engine owner, you should however be aware that
Mercury Marine may deny you warranty coverage if your outboard
engine or a part has failed due to abuse, neglect, improper maintenance
or unapproved modifications.
You are responsible for presenting your outboard to a Mercury dealer
authorized to service the product as soon as a problem exists. The
warranty repairs will be completed in a reasonable amount of time, not
to exceed 30 days.
15
WARRANTY INFORMATION
If you have any questions regarding your warranty rights and
responsibilities, you should contact Mercury Marine at 1-920-929-5040.
Star Label
Outboards are labeled on the cowl with one of the following star labels.
The Symbol for Cleaner Marine Engines Means:
Cleaner Air and Water - for a healthier lifestyle and environment.
Better Fuel Economy - burns up to 30-40 percent less gas and oil than
conventional carbureted two-stroke engines, saving money and
resources.
Longer Emission Warranty - Protects consumer for worry free operation.
16
WARRANTY INFORMATION
Four Stars - Super Ultra Low Emission
The four Star label identifies engines that
meet the Air Resources Board's Sterndrive
F
RN T
and Inboard marine engine 2009 exhaust
emission standards. Personal Watercraft
and Outboard marine engines may also
ob00711 comply with these standards. Engines
meeting these standards have 90% lower
emissions than One Star - Low Emission
engines.
17
GENERAL INFORMATION
Boater's Responsibilities
The operator (driver) is responsible for the correct and safe operation of
the boat and safety of its occupants and general public. It is strongly
recommended that each operator (driver) read and understand this
entire manual before operating the outboard.
Be sure at least one additional person on board is instructed in the
basics of starting and operating the outboard and boat handling in case
the driver is unable to operate the boat.
DANGER
DANGER - indicates an imminently hazardous situation that, if not
avoided, will result in death or serious injury.
WARNING
WARNING - indicates a potentially hazardous situation that, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION - indicates a potentially hazardous situation that, if not
avoided, may result in minor or moderate injury or property damage. It
may also be used to alert against unsafe practices.
18
GENERAL INFORMATION
Do not overpower or overload your boat. Most boats will carry a required
capacity plate indicating the maximum acceptable power and load as
determined by the manufacturer following certain federal guidelines. If in
doubt, contact your dealer or the boat manufacturer.
ob00306
ob00307
19
GENERAL INFORMATION
WARNING
Avoid serious injury or death from a sudden unexpected acceleration
when starting your engine. The design of this outboard requires that
the remote control used with it must have a built in start in neutral only
protection device.
ob00308
WARNING
Disengagement of a steering link rod can result in the boat taking a
full, sudden, sharp turn. This potentially violent action can cause
occupants to be thrown overboard exposing them to serious injury or
death.
a ob00309
a - Self-locking nuts
20
GENERAL INFORMATION
Lanyard Stop Switch
The purpose of a lanyard stop switch is to turn off the engine when the
operator moves far enough away from the operator's position (as in
accidental ejection from the operator's position) to activate the switch.
Tiller handle outboards and some remote control units are equipped with
a lanyard stop switch. A lanyard stop switch can be installed as an
accessory - generally on the dashboard or side adjacent to the
operator's position.
The lanyard is a cord usually between 122 and 152 cm (4 and 5 feet) in
length when stretched out, with an element on one end made to be
inserted into the switch and a snap on the other end for attaching to the
operator. The lanyard is coiled to make its at-rest condition as short as
possible to minimize the likelihood of lanyard entanglement with nearby
objects. Its stretched-out length is made to minimize the likelihood of
accidental activation should the operator choose to move around in an
area close to the normal operator's position. If it is desired to have a
shorter lanyard, wrap the lanyard around the operator's wrist or leg, or
tie a knot in the lanyard.
a b
ob00310
a - Lanyard cord b - Lanyard stop switch
21
GENERAL INFORMATION
Important Safety Information: The purpose of a lanyard stop switch is to
stop the engine when the operator moves far enough away from the
operator's position to activate the switch. This would occur if the
operator accidentally falls overboard or moves within the boat a
sufficient distance from the operator's position. Falling overboard and
accidental ejections are more likely to occur in certain types of boats
such as low sided inflatables, bass boats, high performance boats, and
light, sensitive handling fishing boats operated by a hand tiller. Falling
overboard and accidental ejections are also likely to occur as a result of
poor operating practices such as sitting on the back of the seat or
gunwale at planing speeds, standing at planing speeds, sitting on
elevated fishing boat decks, operating at planing speeds in shallow or
obstacle infested waters, releasing your grip on a steering wheel or tiller
handle that is pulling in one direction, drinking alcohol or consuming
drugs, or daring, high speed boat maneuvers.
While activation of the lanyard stop switch will stop the engine
immediately, a boat will continue to coast for some distance depending
upon the velocity and degree of any turn at shut down. However, the
boat will not complete a full circle. While the boat is coasting, it can
cause injury to anyone in the boat's path as seriously as the boat would
when under power.
We strongly recommend that other occupants be instructed on proper
starting and operating procedures should they be required to operate the
engine in an emergency (e.g. if the operator is accidentally ejected).
WARNING
Should the operator fall out of the boat, the possibility of serious injury
or death from being run over by the boat can be greatly reduced by
stopping the engine immediately. Always properly connect both ends
of the stop switch lanyard to the stop switch and the operator.
WARNING
Avoid serious injury or death from deceleration forces resulting from
accidental or unintended stop switch activation. The boat operator
should never leave the operator's station without first disconnecting
the stop switch lanyard from the operator.
22
GENERAL INFORMATION
Accidental or unintended activation of the switch during normal
operation is also a possibility. This could cause any, or all, of the
following potentially hazardous situations:
• Occupants could be thrown forward due to unexpected loss of
forward motion - a particular concern for passengers in the front of
the boat who could be ejected over the bow and possibly struck by
the gearcase or propeller.
• Loss of power and directional control in heavy seas, strong current
or high winds.
• Loss of control when docking.
ob00311
Always slow down and exercise extreme caution any time you are
boating in an area where there might be people in the water.
Whenever a boat is moving (coasting) and the outboard gear shift is in
neutral position, there is sufficient force by the water on the propeller to
cause the propeller to rotate. This neutral propeller rotation can cause
serious injury.
WHILE BOAT IS STATIONARY
WARNING
Stop your engine immediately whenever anyone in the water is near
your boat. Serious injury to the person in the water is likely if contacted
by a rotating propeller, a moving boat, a moving gearcase, or any solid
device rigidly attached to a moving boat or gearcase.
Shift outboard into neutral and shut off the engine before allowing
people to swim or be in the water near your boat.
23
GENERAL INFORMATION
Passenger Safety Message - Pontoon Boats And
Deck Boats
Whenever the boat is in motion, observe the location of all passengers.
Do not allow any passengers to stand or use seats other than those
designated for traveling faster than idle speed. A sudden reduction in
boat speed, such as plunging into a large wave or wake, a sudden
throttle reduction, or a sharp change of boat direction, could throw them
over the front of boat. Falling over the front of the boat between the two
pontoons will position them to be run over by the outboard.
BOATS HAVING AN OPEN FRONT DECK
No one should ever be on the deck in front of the fence while the boat is
in motion. Keep all passengers behind the front fence or enclosure.
Persons on the front deck could easily be thrown overboard or persons
dangling their feet over the front edge could get their legs caught by a
wave and pulled into the water.
ob00312
WARNING
Avoid serious injury or death from falling over the front end of a
pontoon or deck boat and being run over by the outboard. Stay back
from the front end of the deck and remain seated while the boat is in
motion.
24
GENERAL INFORMATION
Any unexpected, sudden reduction in boat speed could result in the
elevated passenger falling over the front of the boat.
ob00313
ob00314
The primary concern is the boat changing direction while in the midst of
the jump. In such case the landing may cause the boat to veer violently
in a new direction. Such a sharp change in direction can cause
occupants to be thrown out of their seats, or out of the boat.
WARNING
Avoid serious injury or death from being thrown within or out of a boat
when it lands after jumping a wave or wake. Avoid wave or wake
jumping whenever possible. Instruct all occupants that if a wake or
wave jump occurs, get low and hang on to a boat hand hold.
There is another less common hazardous result from allowing your boat
to launch off a wave or wake. If the bow of your boat pitches down far
enough while airborne, upon water contact it may penetrate under the
water surface and submarine for an instant. This will bring the boat to a
nearly instantaneous stop and can send the occupants flying forward.
The boat may also steer sharply to one side.
25
GENERAL INFORMATION
Impact With Underwater Hazards
Reduce speed and proceed with caution whenever you drive a boat in
shallow water areas, or in areas where you suspect underwater
obstacles may exist which could be struck by the outboard or the boat
bottom. The most important thing you can do to help reduce injury or
impact damage from striking a floating or underwater object is to control
the boat speed. Under these conditions, boat speed should be kept to a
minimum planing speed 24 to 40 km/h (15 to 25 MPH) .
ob00315
WARNING
To avoid serious injury or death from all or part of an outboard coming
into the boat after striking a floating or underwater obstacle maintain a
top speed no greater than minimum planing speed.
26
GENERAL INFORMATION
The boat should also be checked for any hull fractures, transom
fractures, or water leaks.
Operating a damaged outboard could cause additional damage to other
parts of the outboard, or could affect control of the boat. If continued
running is necessary, do so at greatly reduced speeds.
WARNING
Avoid serious injury or death from loss of boat control. Continued
boating with major impact damage can result in sudden outboard
component failure with or without subsequent impacts. Have the
outboard thoroughly inspected and any necessary repairs made.
WARNING
Avoid serious injury or death from being struck by a disconnected
outboard. Do not accelerate above idle speed in water suspected of
containing underwater obstacles if the outboard is not attached to the
transom correctly.
Exhaust Emissions
BE ALERT TO CARBON MONOXIDE POISONING
Carbon monoxide is present in the exhaust fumes of all internal
combustion engines. This includes the outboards, sterndrives and
inboard engines that propel boats, as well as the generators that power
various boat accessories. Carbon monoxide is a deadly gas that is
odorless, colorless and tasteless.
27
GENERAL INFORMATION
Early symptoms of carbon monoxide poisoning which should not be
confused with seasickness or intoxication, include headache, dizziness,
drowsiness, and nausea.
WARNING
Avoid the combination of a running engine and poor ventilation.
Prolonged exposure to carbon monoxide in sufficient concentration
can lead to unconsciousness, brain damage, or death.
GOOD VENTILATION
Ventilate passenger area, open side curtains, or forward hatches to
remove fumes.
ob00316
ob00317
a - Running the engine when the boat is moored in a confined
space.
b - Mooring close to another boat that has its engine running.
28
GENERAL INFORMATION
WHILE BOAT IS MOVING
a b
ob00318
a - Running the boat with the trim angle of the bow too high.
b - Running the boat with no forward hatches open.
WARNING
Check with your dealer before installation of accessories. The misuse
of acceptable accessories or the use of unacceptable accessories can
result in serious injury, death, or product failure.
29
GENERAL INFORMATION
Know and obey all nautical rules and laws of the waterways. Boat
operators should complete a boating safety course. Courses are offered
in the U.S.A. by 1) The U.S. Coast Guard Auxiliary, 2) The Power
Squadron, 3) The Red Cross and 4) your state boating law enforcement
agency. Inquiries may be made to the Boating Hotline, 1-800-368-5647
or the Boat U.S. Foundation information number 1-800-336-BOAT.
Make sure everyone in the boat is properly seated. Do not allow anyone
to sit or ride on any part of the boat that was not intended for such use.
This includes the back of seats, gunwales, transom, bow, decks, raised
fishing seats, any rotating fishing seat; or anywhere that an unexpected
acceleration, sudden stopping, unexpected loss of boat control, or
sudden boat movement could cause a person to be thrown overboard or
into the boat.
Never be under the influence of alcohol or drugs while boating (it is the
law). Alcohol or drug use impairs your judgment and greatly reduces
your ability to react quickly.
Prepare other boat operators. Instruct at least one other person on
board in the basics of starting and operating the outboard, and boat
handling, in case the driver becomes disabled or falls overboard.
Passenger boarding. Stop the engine whenever passengers are
boarding, unloading, or are near the back (stern) of the boat. Just
shifting the outboard into neutral is not sufficient.
Be alert. The operator of the boat is responsible by law to maintain a
proper lookout by sight and hearing. The operator must have an
unobstructed view particularly to the front. No passengers, load, or
fishing seats should block the operators view when operating the boat
above idle speed.
Never drive your boat directly behind a water skier in case the skier falls.
As an example, your boat traveling at 40 km/h (25 MPH) will overtake a
fallen skier 61 m (200 ft.) in front of you in 5 seconds.
Watch fallen skiers. When using your boat for water skiing or similar
activities, always keep a fallen or down skier on the operator's side of
the boat while returning to assist the skier. The operator should always
have the down skier in sight and never back up to the skier or anyone in
the water.
30
GENERAL INFORMATION
Report accidents. Boat operators are required by law to file a Boating
Accident Report with their state boating law enforcement agency when
their boat is involved in certain boating accidents. A boating accident
must be reported if 1) there is loss of life or probable loss of life, 2) there
is personal injury requiring medical treatment beyond first aid, 3) there is
damage to boats or other property where the damage value exceeds
$500.00 or 4) there is complete loss of the boat. Seek further assistance
from local law enforcement.
a
OTXXXXXX b
20XX
XXXX c
e
d
XX
ob00319
a - Serial number d - Year manufactured
b - Model year e - Certified Europe Insignia (as
c - Model designation applicable)
31
GENERAL INFORMATION
Models 40 50 60
Cylinder Bore 65 mm (2.559 in.)
Stroke 75 mm (2.953 in.)
Valve
Clearance (Cold)
Intake Valve 0.15-0.25mm (0.006-0.010 in.)
Exhaust Valve 0.25-0.35mm (0.010-0.014 in.)
Recommended Spark
Champion RA8HC
Plug
Spark Plug Gap 1.0mm (0.040 in.)
Gear Ratio
83mm (3-1/4 in.) 1.83:1
Diameter Gearcase
108mm (4-1/4 in.) 2.31:1 or 2.33:1
Diameter Gearcase
Recommended
Refer to Fuel & Oil
Gasoline
Recommended Oil Refer to Fuel & Oil
Gearcase Lubricant
Capacity
83mm (3-1/4 in.) 340 ml (11.5 fl. oz.)
Diameter Gearcase
108mm (4-1/4 in.) 710 ml (24.0 fl. oz.)
Diameter Gearcase
Engine Oil Capacity 3.0 Liter (3 Quarts)
Battery Rating
Operation Above 465 Marine Cranking Amps (MCA) or 350
0 °C (32 °F) Cold Cranking AMPS (CCA)
Operation Below 1000 Marine Cranking Amps (MCA) or 750
0 °C (32 °F) Cold Cranking AMPS (CCA)
Ampere Hours (Ah) 70 -100
32
GENERAL INFORMATION
Component Identification
m
l
k
j n
a
i o
b
p
c
h
g
d
f
e ob00647
33
INSTALLATION
Installing Outboard
WARNING
Before operation, the outboard must be correctly installed with the
required mounting hardware as shown. Failure to correctly fasten
outboard could result in outboard ejecting off boat transom causing
serious injury, death, or property damage.
ob00658
ob00659
34
INSTALLATION
Propeller Selection
For best all around performance from your outboard/boat combination,
select a propeller that allows the engine to operate in the upper half of
the recommended full throttle RPM range with the boat normally
loaded (refer to General Information - Specifications). This RPM range
allows for better acceleration while maintaining maximum boat speed.
ob00323
35
TRANSPORTING
Trailering Boat/Outboard
Trailer your boat with the outboard tilted down in a vertical operating
position.
If additional ground clearance is required, the outboard should be tilted
up using an accessory outboard support device. Refer to your local
dealer for recommendations. Additional clearance may be required for
railroad crossings, driveways and trailer bouncing.
ob00324
IMPORTANT: Do not rely on the power trim/tilt system or tilt support
lever to maintain proper ground clearance for trailering. The outboard tilt
support lever is not intended to support the outboard for trailering.
Shift the outboard to forward gear. This prevents the propeller from
spinning freely.
ob00325
36
TRANSPORTING
AUTO-VENTING TYPE FUEL TANK
1. Disconnect the remote fuel line from tank. This will close the air vent
and prevent escape of fuel or vapors from tank.
2. Install tether cap over the fuel line connector stem. This will protect
the connector stem from being accidently pushed-in, thus, allowing
fuel or vapor to escape.
b ob00326
a - Connector stem b - Tether cap
37
FUEL & OIL
Gasoline Recommendations
UNITED STATES AND CANADA
Use a major brand of automotive unleaded gasoline with a minimum
posted octane rating of 87. Mid-grade automotive gasolines that contain
fuel injector cleaner are preferred for added internal engine cleanliness.
Leaded gasoline is not recommended.
INTERNATIONAL
Use a major brand of automotive unleaded gasoline with a minimum
posted octane rating of 90RON. Automotive gasolines that contain fuel
injector cleaner are preferred for added internal engine cleanliness.
Leaded gasoline is acceptable in areas where unleaded gasoline is not
available.
USING REFORMULATED (OXYGENATED) FUELS - UNITED
STATES ONLY
This type of fuel is required in certain areas of the United States. The
two types of reformulated ingredients in these fuels are alcohol (Ethanol)
or Ether (MTBE or ETBE). If Ethanol is the oxygenates that is used in
the gasoline, refer to Alcohol in Gasoline.
These reformulated fuels are acceptable for use in the Mercury engine.
ALCOHOL IN GASOLINE
We do not recommend the use of gasoline which contains alcohol
because of the possible adverse effect the alcohol may have on the fuel
system. In general, if only gasoline containing alcohol is available, it
must not contain more than 10% ethanol or 5% methanol, and the
addition of a water separating fuel filter is recommended.
If gasoline containing alcohol is used or if you suspect the presence of
alcohol in your gasoline, increase your inspection of the fuel system,
visually checking for fuel leaks or abnormalities.
Gasoline containing alcohol may cause the following problems to your
outboard and fuel system:
• Corrosion of metal parts
• Deterioration of elastomers and plastic parts
• Wear and damage of internal engine parts
• Starting and operating difficulties
• Vapor lock or fuel starvation
Some of these adverse effects are due to the tendency of gasoline
containing alcohol to absorb moisture from the air, resulting in a phase
of water and alcohol which separates from the gasoline in the fuel tank.
38
FUEL & OIL
The adverse effects of alcohol are more severe with methanol and are
worse with increasing content of alcohol.
Fill fuel tanks outdoors away from heat, sparks, and open flames.
Remove portable fuel tanks from boat to refill them.
Always stop engine before refilling tanks.
Do not completely fill the fuel tanks. Leave approximately 10% of the
tank volume unfilled. Fuel will expand in volume as its temperature rises
and can leak under pressure if the tank is completely filled.
PORTABLE FUEL TANK PLACEMENT IN THE BOAT
Place the fuel tank in the boat so the vent is higher than the fuel level
under normal boat operating conditions.
39
FUEL & OIL
Engine Oil Recommendations
We recommend the use of Mercury or Quicksilver SAE 10W-30
multi-viscosity 4-stroke outboard oil for general, all-temperature use. If
SAE 25W-40 multi-viscosity oil is preferred, use Mercury MerCruiser
4-cycle engine oil or Quicksilver sterndrive & inboard 4-cycle engine oil.
Never use 4-cycle engine oil that is not certified to meet or exceed any
one or combination of the following American Petroleum Institute (API)
Service Classification SH, SG, SF, CF-4, CE, CD, CDII. Severe engine
damage may result from use of an inferior oil.
a b
F° C°
+100 +38
+80 +27
+60 +16
+40 +4
+20 –7
0 –18
ob00327
40
FUEL & OIL
2. Flip the handle up and pull out the dipstick. Wipe it with a clean rag
or towel and push it back in all the way.
3. Pull the dipstick back out again and observe the oil level. If the oil
level is low, remove the oil filler cap and fill to (but not over) the
upper oil level with the recommended oil.
ob01456
b
a
ob00648
a - Dipstick b - Oil filler cap
41
FEATURES & CONTROLS
Remote Control Features
Your boat may be equipped with one of the Mercury Precision or
Quicksilver remote controls shown. If not, consult your dealer for a
description of the functions and operations of the remote control.
c c
c
a
a b
b h
f g
i
a
i
d
d f
e g f
e ob00329
42
FEATURES & CONTROLS
Warning System
The outboard warning system incorporates a warning horn inside the
boat. Remote control models will have the warning horn located inside
the remote control or connected to the ignition key switch. Tiller handle
models will have the warning horn located in the ignition key panel.
a b c ob00332
a - Horn inside remote control c - Horn in ignition key panel
b - Horn connected to ignition
key switch
Warning Horn
Function Sound Description
Start Up One Beep Normal System Test
Engine Fault Six Beeps at Start Up The horn sounds
or While Driving when there may be a
problem with one of
the engine functions.
Have your dealer
check the engine soon.
43
FEATURES & CONTROLS
Warning Horn
Function Sound Description
Engine Fault Three Beeps every 4 Engine problem has
Minutes occurred. Engine will
run rough and/or stall.
Engine may not start.
Advancing the remote
control neutral fast
idle feature or
advancing the tiller
handle throttle grip
half way may assist
starting. Have your
dealer check the
engine
Engine Fault Intermittent Beep Engine problem has
occurred. Engine will
not run. Have your
dealer check the
engine
Cooling System Continuous Engine Guardian
Problem System is activated.
Power limit will vary
with level of overheat.
Shift outboard into
neutral and check for
a steady stream of
water coming out of
the water pump
indicator hole. If no
water is coming out of
the water pump
indicator hole or flow
is intermittent, stop
engine and check
water intake holes for
obstruction.
44
FEATURES & CONTROLS
Warning Horn
Function Sound Description
Low Oil Pressure Continuous Engine Guardian
System is activated.
Power will be limited
to 2000 RPM. First,
stop the engine and
check the oil level.
Add oil if necessary.
Engine Overspeed Continuous The warning horn is
activated any time
engine speed
exceeds the
maximum allowable
RPM. The system will
limit the engine speed
to within the allowable
range. Engine
overspeed indicates a
condition that should
be corrected.
Overspeed could be
caused by incorrect
propeller pitch, engine
height, trim angle, etc.
Battery Voltage to Continuous Engine Guardian
High or to Low System is activated.
Power limit will restrict
engine speed to 75%.
Coolant Sensor Continuous Engine Guardian
Failure System is activated.
Power limit will restrict
engine speed to 50%.
45
FEATURES & CONTROLS
If Guardian System has been activated, reduce throttle speed. The horn
will turn off when throttle speed is within the allowable limit. Consult your
dealer for assistance.
SMARTCRAFT PRODUCT
A Mercury SmartCraft System instrument package can be purchased for
this outboard. A few of the functions the instrument package will display
are engine RPM, coolant temperature, battery voltage, fuel consumption
and engine operating hours.
The SmartCraft Instrument package will also aid in Engine Guardian
diagnostics. The SmartCraft Instrument package will display critical
engine alarm data and potential problems.
b
c
d
ob00338
a - Remote control trim switch c - Tilt range of travel
b - Panel mount trim switch d - Trim range of travel
46
FEATURES & CONTROLS
POWER TRIM OPERATION
With most boats, operating around the middle of the trim range will give
satisfactory results. However, to take full advantage of the trimming
capability there may be times when you choose to trim your outboard all
the way in or out. Along with an improvement in some performance
aspects comes a greater responsibility for the operator, and this is being
aware of some potential control hazards.
The most significant control hazard is a pull or torque that can be felt on
the steering wheel or tiller handle. This steering torque results from the
outboard being trimmed so that the propeller shaft is not parallel to the
water surface.
WARNING
Avoid possible serious injury or death. When the outboard is trimmed
in or out beyond a neutral steering condition, a pull on the steering
wheel or tiller handle in either direction may result. Failure to keep a
continuous firm grip on the steering wheel or tiller handle when this
condition exists can result in loss of boat control as the outboard can
turn freely. The boat can now spin out or go into a very tight maximum
turn which, if unexpected, can result in occupants being thrown within
the boat or out of the boat.
47
FEATURES & CONTROLS
• In excess can lower the bow of some boats to a point where they
begin to plow with their bow in the water while on plane. This can
result in an unexpected turn in either direction (called bow steering
or over-steering) if any turn is attempted, or if a significant wave is
encountered.
WARNING
Avoid possible serious injury or death. Adjust outboard to an
intermediate trim position as soon as boat is on plane to avoid
possible ejection due to boat spin out. Do not attempt to turn boat
when on plane if outboard is trimmed extremely in or down and
there is a pull on the steering wheel or tiller handle.
• In rare circumstances, the owner may decide to limit the trim in. This
can be accomplished by repositioning the tilt stop pins into whatever
adjustment holes in the transom brackets are desired.
Trimming Out or Up can:
• Lift the bow higher out of the water.
• Generally increase top speed.
• Increase clearance over submerged objects or a shallow bottom.
• Increase steering torque or pull to the left at a normal installation
height (with the normal right hand rotation propeller).
• In excess can cause boat porpoising (bouncing) or propeller
ventilation.
• Cause engine overheating if any cooling water intake holes are
above the water line.
TILTING OPERATION
To tilt outboard, shut off the engine and press the trim/tilt switch or
auxiliary tilt switch to the up position. The outboard will tilt up until the
switch is released or it reaches its maximum tilt position.
1. Engage the tilt support lever, by rotating knob to bring the support
lever upward.
2. Lower outboard to rest on the tilt support lever.
48
FEATURES & CONTROLS
3. Disengage the tilt support lever, by raising the outboard off the
support lever and rotating the lever down. Lower the outboard.
b ob00336
a - Tilt support lever b - Knob
MANUAL TILTING
If the outboard cannot be tilted using the power trim/tilt switch, the
outboard can be manually tilted.
1. Turn out the manual tilt release valve 3 turns counterclockwise. This
allows manual tilting of the outboard. Tilt the outboard to the desired
position and tighten the manual tilt release valve.
ob00339
NOTE: The manual tilt release valve must be tightened before operating
the outboard to prevent the outboard from tilting up during reverse
operation.
49
FEATURES & CONTROLS
AUXILIARY TILT SWITCH
The auxiliary tilt switch can be used to tilt the outboard up or down using
the power trim system.
ob00340
a - Auxiliary tilt switch
ob00334
50
FEATURES & CONTROLS
Throttle Grip Friction Adjustment - Tiller Handle
Models
Throttle Grip Friction Knob - Turn friction knob to set and maintain the
throttle at desired speed. Turn knob clockwise to tighten friction and turn
knob counterclockwise to loosen friction.
a
b
ob00341
a - Loosen friction b - Tighten friction
a b
c
ob00342
a - Tighten friction c - Locknut
b - Loosen friction
51
FEATURES & CONTROLS
REMOTE STEERING MODELS
WARNING
Avoid possible serious injury or death from loss of boat control.
Maintain sufficient steering friction to prevent the outboard from
steering into a full turn if the tiller handle is released.
a b
ob00343
a - Loosen friction b - Tighten friction
ob00344
NOTE: Trim tab adjustment will have little effect reducing steering
torque if the outboard is installed with the anti-ventilation plate
approximately 50 mm (2 in.) or more above the boat bottom.
52
FEATURES & CONTROLS
MODELS WITHOUT POWER TRIM
Operate your boat at normal cruising speed trimmed to desired position
by installing the tilt pin in the desired tilt pin hole. Turn your boat left and
right and note the direction the boat turns more easily.
If adjustment is necessary, loosen trim tab bolt and make small
adjustments at a time. If the boat turns more easily to the left, move the
trailing edge of trim tab to the left. If the boat turns more easily to the
right move the trailing edge of trim tab to the right. Retighten bolt and
retest.
MODELS WITH POWER TRIM
Operate your boat at normal cruising speed, trimmed to desired position.
Turn your boat left and right and note the direction the boat turns more
easily.
If adjustment is necessary, loosen trim tab bolt and make small
adjustments at a time. If the boat turns more easily to the left, move the
trailing edge of trim tab to the left. If the boat turns more easily to the
right move the trailing edge of trim tab to the right. Retighten bolt and
retest.
53
OPERATION
Pre-Starting Check List
• Operator knows safe navigation, boating, and operating procedures.
• An approved personal flotation device of suitable size for each
person aboard and readily accessible (it is the law).
• A ring type life buoy or buoyant cushion designed to be thrown to a
person in the water.
• Know your boats maximum load capacity. Look at the boat capacity
plate.
• Fuel supply OK.
• Arrange passengers and load in the boat so the weight is distributed
evenly and everyone is seated in a proper seat.
• Tell someone where you are going and when you expect to return.
• It is illegal to operate a boat while under the influence of alcohol or
drugs.
• Know the waters and area you will be boating; tides, currents, sand
bars, rocks, and other hazards.
• Make inspection checks listed in Maintenance - Inspection and
Maintenance Schedule.
54
OPERATION
Wash down the outboard exterior and flush out the exhaust outlet of the
propeller and gearcase with fresh water after each use. Each month,
spray Mercury Precision or Quicksilver Corrosion Guard on external
metal surfaces. Do not spray on corrosion control anodes as this will
reduce the effectiveness of the anodes.
Pre-Starting Instructions
1. Connect the remote fuel line to the outboard. Make sure connector is
snapped into place.
ob00345
ob00346
55
OPERATION
3. Make sure the cooling water intake is submerged.
CAUTION
Never start or operate your outboard (even momentarily) without
water circulating through all the cooling water intake holes in the
gearcase to prevent damage to the water pump (running dry) or
overheating of the engine.
ob00347
1. For the first hour of operation, run the engine at varied throttle
settings up to 3500 RPM or at approximately half throttle.
2. For the second hour of operation, run the engine at varied throttle
settings up to 4500 RPM or at three-quarter throttle, and during this
period of time, run it at full throttle for approximately one minute
every ten minutes.
3. For the next eight hours of operation, avoid continuous operation at
full throttle for more than five minutes at a time.
56
OPERATION
CAUTION
Never start or operate your outboard (even momentarily) without water
circulating through all the cooling water intake holes in the gearcase to
prevent damage to the water pump (running dry) or overheating of the
engine.
1. Open fuel tank vent screw (in filler cap) on manual venting type fuel
tanks.
ob00348
2. Squeeze the fuel line primer bulb several times until it feels firm.
ob00349
ob00350
ob00351
57
OPERATION
5. Move the neutral fast idle speed feature to the fully closed position.
a a
b
ob00353
a - Fully closed position b - Maximum fast idle speed
position
ob00354
8. After engine starts, check for a steady stream of water flowing out of
the water pump indicator hole.
ob00331
58
OPERATION
WARMING UP ENGINE
Before beginning operation, allow the engine to warm up at idling speed
for 3 minutes.
CAUTION
Never start or operate your outboard (even momentarily) without water
circulating through all the cooling water intake holes in the gearcase to
prevent damage to the water pump (running dry) or overheating of the
engine.
1. Open fuel tank vent screw (in filler cap) on manual venting type fuel
tanks.
ob00348
2. Squeeze the fuel line primer bulb several times until it feels firm.
ob00349
ob00350
59
OPERATION
4. Shift outboard to neutral (N) position.
ob00355
b
0%100
0%100
a
START
START START
START
ob00356
a - Start position b - Half-way position
ob00354
WARNING
RAPID ACCELERATION HAZARD - Before shifting your outboard
from neutral into gear, decrease engine speed to slow. This will
prevent a rapid acceleration that can cause people in the boat to
be thrown from their seats or out of the boat, causing injury or
death.
60
OPERATION
8. Check for a steady stream of water flowing out of the water pump
indicator hole.
ob00331
Gear Shifting
IMPORTANT: Observe the following:
• Never shift outboard into gear unless engine speed is at idle.
• Do not shift outboard into reverse when the engine is not running.
• Your outboard has three gear shift positions to provide operation:
Forward (F), Neutral (out of gear), and Reverse (R).
F N R F N R
ob00358
61
OPERATION
• Remote Control Models - When shifting, always stop at neutral
position and allow the engine speed to return to idle.
ob00308
START
ob00359
ob00360
ob00361
Emergency Starting
If the starter system fails, use the spare starter rope (provided) and
follow procedure.
62
OPERATION
NOTE: EFI models - Engine must have a fully charged battery to start
the engine.
1. Remove flywheel cover or manual starter assembly.
ob00362
N N
ob00363
WARNING
When using emergency starter rope to start engine, the start in
gear protection device is inoperative. Make sure to set the
outboard gear shift into neutral to prevent outboard from starting in
gear. Sudden unexpected acceleration could result in serious
injury or death.
3. Electric Start Models - Turn the ignition key to "on" position.
ob00364
63
OPERATION
WARNING
To prevent getting an electrical shock, do not touch any ignition
component, wiring, or spark plug wire when starting or running the
engine.
WARNING
The exposed moving flywheel can cause serious injury. Keep your
hands, hair, clothing, tools, and other objects away from engine
when starting or running the engine. Do not attempt to reinstall the
flywheel cover or top cowl when engine is running.
4. Place the starter rope knot into the flywheel notch and wind the rope
clockwise around the flywheel.
5. Pull the starter rope to start the engine.
ob00365
64
MAINTENANCE
Outboard Care
To keep your outboard in the best operating condition, it is important that
your outboard receive the periodic inspections and maintenance listed in
the Inspection and Maintenance Schedule. We urge you to keep it
maintained properly to ensure the safety of you and your passengers,
and retain its dependability.
WARNING
Neglected inspection and maintenance service of your outboard or
attempting to perform maintenance or repair on your outboard if you
are not familiar with the correct service and safety procedures could
cause personal injury, death, or product failure.
WARNING
Using a replacement part that is inferior to the original part could result
in personal injury, death, or product failure.
65
MAINTENANCE
EMISSION CERTIFICATION LABEL
An emission certification label, showing emission levels and engine
specifications directly related to emissions, is placed on the engine at
time of manufacture.
a f
b g
c h
d i
e
ob00366
a- Idle speed f - Family number
b- Engine horsepower g - Maximum emission output
c- Piston displacement for the engine family
d- Date of manufacture h - Timing specification
e- Valve clearance (if i - Recommended spark plug
applicable) and gap
OWNER RESPONSIBILITY
The owner/operator is required to have routine engine maintenance
performed to maintain emission levels within prescribed certification
standards.
The owner/operator is not to modify the engine in any manner that would
alter the horsepower or allow emissions levels to exceed their
predetermined factory specifications.
66
MAINTENANCE
• Visually check steering link rod fasteners for proper tightness. See
Steering Link Rod Fasteners.
• Check propeller blades for damage.
AFTER EACH USE
• Flush out the outboard cooling system if operating in salt or polluted
water. See Flushing the Cooling System.
• Wash off all salt deposits and flush out the exhaust outlet of the
propeller and gearcase with fresh water if operating in salt water.
EVERY 100 HOURS OF USE OR ONCE YEARLY,
WHICHEVER OCCURS FIRST
• Lubricate all lubrication points. Lubricate more frequently when used
in salt water. See Lubrication Points.
• Change engine oil and replace the oil filter. The oil should be
changed more often when the engine is operated under adverse
conditions such as extended trolling. See Changing Engine Oil.
• Replace spark plugs at first 100 hours or first year. After that, inspect
spark plugs every 100 hours or once yearly. Replace spark plugs as
needed. See Spark Plug Inspection and Replacement.
• Inspect thermostat visually for corrosion and broken spring. Make
sure thermostat closes completely at room temperature.1.
• Check engine fuel filter for contaminants. See Fuel System.
• Check engine timing setup.1.
• Check corrosion control anodes. Check more frequently when used
in salt water. See Corrosion Control Anodes.
• Drain and replace gear case lubricant. See Gearcase Lubrication.
• Lubricate splines on the drive shaft.1.
• Check and adjust valve clearance, if necessary.1.
• Check power trim fluid. See Checking Power Trim Fluid.
• Inspect battery. See Battery Inspection.
• Check control cable adjustments.1.
• Inspect timing belt. See Timing Belt Inspection.
• Check tightness of bolts, nuts, and other fasteners.
EVERY 300 HOURS OF USE OR THREE YEARS
• Replace water pump impeller (more often if overheating occurs or
reduced water pressure is noted).1.
WARNING
To avoid possible injury when flushing, remove the propeller. Refer to
Propeller Replacement, following.
ob00367
68
MAINTENANCE
Top Cowl Removal And Installation
REMOVAL
1. Unlock the rear latch by pushing lever down.
ob00368
ob00369
INSTALLATION
1. Engage the front hook and push cowl back over the cowl seal.
2. Push cowl down and move the rear latch lever up to lock.
Exterior Care
Your outboard is protected with a durable baked enamel finish. Clean
and wax often using marine cleaners and waxes.
Battery Inspection
The battery should be inspected at periodic intervals to ensure proper
engine starting capability.
IMPORTANT: Read the safety and maintenance instructions which
accompany your battery.
1. Turn off the engine before servicing the battery.
2. Add water as necessary to keep the battery full.
3. Make sure the battery is secure against movement.
4. Battery cable terminals should be clean, tight, and correctly installed.
Positive to positive and negative to negative.
5. Make sure the battery is equipped with a nonconductive shield to
prevent accidental shorting of battery terminals.
69
MAINTENANCE
Fuel System
WARNING
Avoid serious injury or death from gasoline fire or explosion. Carefully
follow all fuel system service instructions. Always stop the engine and
do not smoke or allow open flames or sparks in the area while
servicing any part of the fuel system.
Before servicing any part of the fuel system, stop engine and disconnect
the battery. Drain the fuel system completely. Use an approved
container to collect and store fuel. Wipe up any spillage immediately.
Material used to contain spillage must be disposed of in an approved
receptacle. Any fuel system service must be performed in a well
ventilated area. Inspect any completed service work for sign of fuel
leakage.
FUEL LINE INSPECTION
Visually inspect the fuel line and primer bulb for cracks, swelling, leaks,
hardness, or other signs of deterioration or damage. If any of these
conditions are found, the fuel line or primer bulb must be replaced.
ENGINE FUEL FILTER
Check the fuel filter for water accumulation or sediment. If water is in the
fuel, remove the sight bowl and drain the water. If the filter appears to be
contaminated, remove and replace.
REMOVAL
1. Read Fuel System servicing information and Warning proceeding.
2. Pull out the filter assembly from mount. Hold onto the cover to
prevent it from turning and remove the sight bowl. Empty contents
into an approved container.
70
MAINTENANCE
3. Pull out the filter element and replace it if necessary.
d
ob00649
a - Cover c - O-ring seal
b - Filter element d - Sight bowl
INSTALLATION
IMPORTANT: Visually inspect for fuel leakage from the filter by
squeezing the primer bulb until firm, forcing fuel into the filter.
1. Push the filter element into the cover.
2. Place the O-ring seal into its proper position on the sight bowl, and
screw the sight bowl hand tight into the cover.
3. Push filter assembly back into mount.
71
MAINTENANCE
WARNING
Disengagement of a steering link rod can result in the boat taking a
full, sudden, sharp turn. This potentially violent action can cause
occupants to be thrown overboard exposing them to serious injury or
death.
b
c
a
e ob00373
a- Spacer (12-71970)
b- Nylon insert locknut (11-826709113)
c- Flat washer (2)
d- Nylon insert locknut (11-826709113)
e- Special washer head bolt (10-856680)
Assemble steering link rod to steering cable with two flat washers and
nylon insert locknut. Tighten locknut until it seats, then back nut off 1/4
turn.
Assemble steering link rod to engine with special washer head bolt,
locknut and spacer. First torque bolt, then locknut to specification.
72
MAINTENANCE
Corrosion Control Anode
Your outboard has corrosion control anodes at different locations. An
anode helps protect the outboard against galvanic corrosion by
sacrificing its metal to be slowly corroded instead of the outboard metals.
Each anode requires periodic inspection, especially in salt water which
will accelerate the erosion. To maintain this corrosion protection, always
replace the anode before it is completely eroded. Never paint or apply a
protective coating on the anode as this will reduce effectiveness of the
anode.
One anode is installed on the bottom of the transom bracket assembly.
The trim tab is also an anode on the 87.3 mm (3 - 7/16 in.) diameter
gearcase. The 108 mm (4 - 1/4 in.) diameter gearcase has three
anodes. One of the anodes is the trim tab, and the other two anodes are
located on each side of the gearcase.
a ob00374
73
MAINTENANCE
1. Shift outboard to neutral (N) position.
N N
ob00363
ob00375
ob00376
ob00377
74
MAINTENANCE
6. Coat the propeller shaft with Quicksilver or Mercury Precision
Lubricants Anti-Corrosion Grease or 2-4-C with Teflon.
ob00378
IMPORTANT: To prevent the propeller hub from corroding and seizing
to the propeller shaft (especially in salt water), always apply a coat of
the recommended lubricant to the entire propeller shaft at the
recommended maintenance intervals, and also each time the propeller
is removed.
7. Flo-Torq I Drive Hub Propellers - Install forward thrust hub, propeller,
propeller nut retainer and propeller nut onto the shaft.
b
a
c d
ob00379
a - Propeller nut c - Propeller
b - Propeller nut retainer d - Forward thrust hub
a b c
f
d e
ob00380
a - Propeller nut d - Replaceable drive sleeve
b - Propeller nut retainer e - Propeller
c - Rear thrust hub f - Forward thrust hub
75
MAINTENANCE
9. Place propeller nut retainer over pins. Place a block of wood
between gearcase and propeller and tighten propeller nut to
specifications.
a b
a
b ob00381
a - Pins b - Tabs
N N
ob00363
76
MAINTENANCE
2. Remove spark plug leads to prevent engine from starting.
ob00375
ob00376
ob00377
ob00378
77
MAINTENANCE
IMPORTANT: To prevent the propeller hub from corroding and seizing
to the propeller shaft (especially in salt water), always apply a coat of
the recommended lubricant to the entire propeller shaft at the
recommended maintenance intervals, and also each time the propeller
is removed.
7. Flo-Torq I Drive Hub Propellers - Install thrust washer, propeller,
continuity washer, thrust hub, propeller nut retainer, and propeller
nut onto the shaft.
a b c
d e f ob00382
a b c e f
d ob00421
a - Propeller nut d - Propeller
b - Propeller nut retainer e - Replaceable drive sleeve
c - Thrust hub f - Forward thrust hub
78
MAINTENANCE
9. Flo-Torq III Drive Hub Propellers - Install forward thrust hub,
replaceable drive sleeve, propeller, thrust hub, propeller nut retainer
and propeller nut onto the shaft.
f
a b c e
d 3223
10. Place a block of wood between gearcase and propeller and torque
propeller nut to specifications.
ob00422
79
MAINTENANCE
1. Remove the spark plug leads. Twist the rubber boots slightly and
pull off.
ob00375
ob00423
ob00424
Fuse Replacement
IMPORTANT: Always carry spare 20 AMP fuses.
The electrical wiring circuits on the outboard are protected from overload
by fuses in the wiring. If a fuse is blown, try to locate and correct the
cause of the overload. If the cause is not found, the fuse may blow again.
80
MAINTENANCE
Open the fuse holder and look at the silver colored band inside the fuse.
If band is broken, replace the fuse. Replace fuse with a new fuse with
the same rating.
a c
1 3
15
2 4
b d
e
f g
ob00650
a - SmartCraft data bus circuit - 15 AMP fuse
b - Fuel pump/idle air control/fuel injector circuits - SFE 20 AMP
fuse
c - Main relay/accessories - 20 AMP fuse
d - Ignition coil circuit - 20 AMP fuse
e - Spare 20 AMP fuse
f - Good fuse
g - Blown fuse
81
MAINTENANCE
e. Signs of wear on edges or outer surfaces of belt.
ob00427
Lubrication Points
1. Lubricate the following with Quicksilver or Mercury Precision
Lubricants Anti-Corrosion Grease or 2-4-C with Teflon.
• Propeller Shaft - Refer to Propeller Replacement for removal
and installation of the propeller. Coat the entire propeller shaft
with lubricant to prevent the propeller hub from corroding and
seizing to the shaft.
ob00378
82
MAINTENANCE
• Swivel Bracket - Lubricate through fitting.
b
ob00429
a - Tilt support lever b - Swivel bracket
ob00428
WARNING
The end of the steering cable must be fully retracted into the
outboard tilt tube before adding lubricant. Adding lubricant to
steering cable when fully extended could cause steering cable
to become hydraulically locked. A hydraulically locked steering
cable will cause loss of steering control, possibly resulting in
serious injury or death.
• Steering Cable Grease Fitting (If equipped) - Rotate steering
wheel to fully retract the steering cable end into the outboard tilt
tube. Lubricate through fitting.
a
b
ob00432
a - Fitting b - Steering cable end
83
MAINTENANCE
3. Lubricate the following with light weight oil.
• Steering Link Rod Pivot Points - Lubricate points.
ob00433
ob00434
2. Remove fill cap and check fluid level. The fluid level should be even
with the bottom of the fill hole. Add Quicksilver or Mercury Precision
Lubricants Power Trim & Steering Fluid. If not available, use
automotive (ATF) automatic transmission fluid.
ob00435
84
MAINTENANCE
2. Turn the steering on the outboard so that the drain hole is facing
downward. Remove drain plug and drain engine oil into an
appropriate container. Lubricate the seal on the drain plug with oil
and reinstall.
ob00436
ob00437
OIL FILLING
1. Remove the oil fill cap and add oil to proper operating level.
85
MAINTENANCE
2. Idle engine for five minutes and check for leaks. Stop engine and
check oil level on dipstick. Add oil if necessary.
ob00651
a - Oil fill cap
86
MAINTENANCE
3. Remove vent plug and fill/drain plug and drain lubricant.
ob00439
a - Vent plug b - Fill/drain plug
b
c
ob00440
a - Vent hole c - Fill/drain plug
b - Vent plug
87
MAINTENANCE
Gearcase Lubrication - For 108 mm (4 - 1/4 in.)
Diameter Gearcase
When adding or changing gearcase lubricant, visually check for the
presence of water in the lubricant. If water is present, it may have settled
to the bottom and will drain out prior to the lubricant, or it may be mixed
with the lubricant, giving it a milky colored appearance. If water is
noticed, have the gearcase checked by your dealer. Water in the
lubricant may result in premature bearing failure or, in freezing
temperatures, will turn to ice and damage the gearcase.
Examine the drained gearcase lubricant for metal particles. A small
amount of fine metal particles indicates normal gear wear. An excessive
amount of metal filings or larger particles (chips) may indicate abnormal
gear wear and should be checked by an authorized dealer.
DRAINING GEARCASE
1. Place outboard in a vertical operating position.
2. Place a drain pan below outboard.
3. Remove vent plugs and fill/drain plug and drain lubricant.
a
b
ob00441
a - Vent plugs b - Fill/drain plug
88
MAINTENANCE
5. Stop adding lubricant. Install the rear vent plug and sealing washer
before removing lubricant tube.
6. Remove lubricant tube and reinstall cleaned fill/drain plug and
sealing washer.
c
b a d
e
ob00442
a - Front vent plug d - Rear vent plug
b - Front vent hole e - Fill/drain plug and sealing
c - Rear vent hole washer
Submerged Outboard
A submerged outboard will require service within a few hours by an
authorized dealer once the outboard is recovered from the water. This
immediate attention by a servicing dealer is necessary once the engine
is exposed to the atmosphere to minimize internal corrosion damage to
the engine.
89
STORAGE
Storage Preparation
The major consideration in preparing your outboard for storage is to
protect it from rust, corrosion, and damage caused by freezing of
trapped water.
The following storage procedures should be followed to prepare your
outboard for out of season storage or prolonged storage (two months or
longer).
CAUTION
Never start or operate your outboard (even momentarily) without water
circulating through all the cooling water intake holes in the gearcase to
prevent damage to the water pump (running dry) or overheating of the
engine.
FUEL SYSTEM
IMPORTANT: Gasoline containing alcohol (ethanol or methanol) can
cause a formation of acid during storage and can damage the fuel
system. If the gasoline being used contains alcohol, it is advisable to
drain as much of the remaining gasoline as possible from the fuel tank,
remote fuel line, and engine fuel system.
Fill the fuel tank and engine fuel system with treated (stabilized) fuel to
help prevent formation of varnish and gum. Proceed with following
instructions.
• Portable Fuel Tank - Pour the required amount of gasoline
stabilizer (follow instructions on container) into fuel tank. Tip fuel
tank back and forth to mix stabilizer with the fuel.
• Permanently Installed Fuel Tank - Pour the required amount of
gasoline stabilizer (follow instructions on container) into a separate
container and mix with approximately one quart (one liter) of
gasoline. Pour this mixture into fuel tank.
• Remove the fuel filter sight bowl and empty contents in a suitable
container. Refer to Maintenance- Fuel System for removal and
installation of filter. Add 3 cc (1/2 tsp.) of gasoline stabilizer into the
fuel filter sight bowl and reinstall.
• Place the outboard in water or connect flushing attachment for
circulating cooling water. Run the engine for 15 minutes to fill the
engine fuel system.
90
STORAGE
Protecting External Outboard Components
• Lubricate all outboard components listed in Maintenance -
Inspection and Maintenance Schedule.
• Touch up any paint nicks. See your dealer for touch-up paint.
• Spray Quicksilver or Mercury Precision Lubricants Corrosion Guard
on external metal surfaces (except corrosion control anodes).
Gearcase
• Drain and refill the gearcase lubricant (refer to Maintenance -
Gearcase Lubrication).
CAUTION
If outboard is stored tilted up in freezing temperature, trapped cooling
water or rain water that may have entered the propeller exhaust outlet
in the gearcase could freeze and cause damage to the outboard.
Battery Storage
• Follow the battery manufacturer's instructions for storage and
recharging.
• Remove the battery from the boat and check water level. Recharge if
necessary.
• Store the battery in a cool, dry place.
• Periodically check the water level and recharge the battery during
storage.
91
TROUBLESHOOTING
Starter Motor Will Not Crank The Engine (Electric
Start Models)
POSSIBLE CAUSES
• Blown 20 Amp fuse in the starting circuit. Refer to Maintenance
section.
• Outboard is not shifted to neutral position.
• Weak battery or battery connections are loose or corroded.
• Ignition key switch failure.
• Wiring or electrical connection faulty.
• Starter motor or starter solenoid failure.
92
TROUBLESHOOTING
• Incorrect setup and adjustments.
• Fuel is being restricted to the engine.
a. Engine fuel filter is obstructed. Refer to Maintenance section.
b. Fuel tank filter obstructed.
c. Stuck anti-siphon valve located on permanently built-in type fuel
tanks.
d. Fuel line is kinked or pinched.
• Fuel pump failure.
• Ignition system component failure.
• Fuel injection component failure (EFI Models).
Performance Loss
POSSIBLE CAUSES
• Engine Guardian System activated. Refer to Features & Controls -
Warning System.
• Throttle not fully open.
• Damaged or improper size propeller.
• Incorrect engine timing, adjustments, or setup.
• Boat overloaded or load improperly distributed.
• Excessive water in bilge.
• Boat bottom is dirty or damaged.
93
OWNER SERVICE ASSISTANCE
Local Repair Service
Always return your outboard to your local authorized dealer should the
need for service arise. Only he has the factory trained mechanics,
knowledge, special tools, equipment, and genuine parts and accessories
to properly service your engine should the need occur. He knows your
engine best.
Service Assistance
Your satisfaction with your outboard product is very important to your
dealer and to us. If you ever have a problem, question or concern about
your outboard product, contact your dealer or any authorized Mercury
Marine dealership. If additional assistance is required, take these steps.
1. Talk with the dealership's sales manager or service manager. If this
has already been done, then contact the owner of the dealership.
2. Should you have a question, concern, or problem that cannot be
resolved by your dealership, please contact Mercury Marine Service
Office for assistance. Mercury Marine will work with you and your
dealership to resolve all problems.
The following information will be needed by the service office:
• Your name and address
• Daytime telephone number
• Model and serial number of your outboard
• The name and address of your dealership
• Nature of problem
94
OWNER SERVICE ASSISTANCE
Mercury Marine Service Offices
For assistance, call, fax, or write. Please include your daytime telephone
number with mail and fax correspondence.
United States
Telephone (920) 929-5040 Mercury Marine
W6250 W. Pioneer Road
Fax (920) 929-5893 P.O. Box 1939
Website www.mercurymarine.com Fond du Lac, WI 54936-1939
Canada
Telephone (905) 567-6372 Mercury Marine Ltd.
2395 Meadowpine Blvd.
Fax (905) 567-8515 Mississauga, Ontario L5N 7W6
Canada
Australia, Pacific
Telephone (61) (3) 9791-5822 Mercury Marine Australia
132-140 Frankston Road
Fax (61) (3) 9793-5880 Dandenong, Victoria 3164
Australia
95
OWNER SERVICE ASSISTANCE
Japan
Telephone 81-53-423-2500 Mercury Marine - Japan
283-1 Anshin-cho Hamamatsu
Fax 81-53-423-2510 Shizuoka, 435-0005
Japan
Asia, Singapore
Telephone 5466160 Mercury Marine Singapore
72 Loyang Way
Fax 5467789 Singapore, 508762
96
MAINTENANCE LOG
Maintenance Log
Record all maintenance performed on your outboard here. Be sure to
save all work orders and receipts.
97