Professional Documents
Culture Documents
1. Which of the electrical circuit will dissipate more heat : (BLT Page 29 part 1)
a. Figure a
b. Figure b
c. Figure c
d. Both (b) & (c)
3. While running, a synchronous motor is compelled to run at synchronous speed because of:-
(B. L. Thareja Vol II page no 1532, Chapter 38; AC 65-9A, Page-457)
a. damper winding in its pole faces
b. magnetic locking between stator and rotor poles
c. Induced emf. in rotor field winding by stator flux
1(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
4. The speed of a D.C. motor can be controlled by varying: - B.L Thareja, Page – 321
a. Its flux
b. Armature circuit resistance
c. Applied voltage
d. All the above
Page 2 of 11
5. In a thermal switch employing steel and invar element actuation of the contacts under
increasing temperature
condition is caused by: Pallet-223, Chapter 6.
a. expansion of the steel element only
b. contraction of the invar element only
c. expansion of the steel element causing displacement of the in rear element
d. none of the above
8. The method used to rapidly charge a nickel cadmium battery utilizes :- (T.K. Eismin, Page-
Page
52)
a. constant current and constant voltage
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
9. The horn in landing gear warning circuit is activated by: (Ref. EHJ Pallet, 176 & 177)
a. up lock micro s/w
b. down lock micro s/w
c. engine throttle operated micro s/w
d. all the above
10. The condition for LG system horn to come on is: (EHJ Pallett,P-177)
a. Any one LG is not DOWN & locked
b. Any one LG is not UP & locked
c. As in (a) and throttle at landing configuration
d. As in (b) and throttle at take off configuration
13. Mark the correct statement regarding wire bundle : (15A, wire)
a. 3 or more wire going together to the same location
b. 2 or more wire group going to same location
c. 3 or more wire group going to same location
16. Where initial current high & circuit contain high capacitive load, safety device used:
pallett 112
a. Current Limiter
Page
b. Limiting Resister
c. High Rupturing Fuse
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
d. Air Fuse
17. In which side equalizer rings are connected when generators are working in parallel-
pallett pg 18
a. Negative terminal of both generators
b. Negative and Positive terminal of the generator
c. Positive terminals of both generators
18. When full voltage applied on a synchronous motor, Input voltage know as-
(B.L.Thareja Vol II, Chap 38 Page 1501)
a.Breakaway Torque
b. Running Torque
c.Pull in Torque
d.Pull out Torque
19. Two material A and B have resistance Temperature Coefficient of 0.004 and 0.0004 at a
temperature, in what
3(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
proportion A and B join series to produce a circuit having a temperature coefficient of .001?
a. 2
b.3
c.4
d. 5
20. Most common cause of false warning in continuous Loop fire detection system FAA
a. Improper routing or clamping of loops
b. Moisture
c. Dents, Kinks or crushed sensor section
Page 4 of 11
22. Varistor is a solid state device it is primarily consist of- : (BLT Part 1Page 29)
a. Zink oxide
b. Carbons
c. Metal oxide
d. Silicon carbide
24. Which is not the part of Secondary Bonding in aircraft: (Pallett Page 94 Ch-5)
a. Junction Boxes
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
b. Door plates
c. Flight Control Surface
d. Metal conduit
26. Mark the correct statement regarding rain replant system- Pallett page 179.
a. Approximately 5 c.c. fluid flows through the nozzle for approximately 0.25 seconds.
b. Approximately 5 c.c. fluid flows through the nozzle for approximately 0.025 seconds.
c. None of the above
28. In a CSD unit, the control cylinder is mechanically coupled to the: Pallet-221
a. variable displacement unit
b. fixed displacement unit
c. governor
d. none of the above
Page 5 of 11
31. In ATA 100 code wire specification, No. 3 & No. 5 indicates respectively : Pallett- Page-
185
a. Circuit function & Cable segment i.e the portion of the cable between two terminals or
connections.
b. Circuit segment & Cable function i.e the portion of the cable between two terminals or
connections.
c. Circuit unit number and cable radius measured in AWG.
d. Cable numbering which is used to differentiate between cables not having a common
Page
terminal in the
same ckt and the cable size corresponding to AWG sizes.
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
32. The Anti-collision beacon that employs a V- shaped reflector is: (Pallett Page 146)
a. Rotated at about 45 rev/min
b. Rotated at 70-75 cycles/min
c. Rotated at 80-90 cycles/min
d. Rotated at 90-cycles/min
33. If a Lead acid battery is not retaining charge, probable cause may be: BLT- 1 Page 362
chapter 9
a. Set for high charging rate
b. Low electrolyte
c. Defective cell
d. Electrolyte level is below the plate
34. While utilizing co-axial cable, it should be secured firmly along its entire length and
supporting clamp are
placed: (FAA Airmen Question Bank)
5(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
a. at 1 feet interval
b. at 2 feet interval
c. at 4 feet interval
d. wherever cable defines
35. In aircraft ESDS devices after removing from aircraft & taking for line maintenance:
(Esmin page 274)
a. ESDS should be shorted by wire
b. ESDS should be shorted by shorting-clips
c. Both a and b
37. The mechanical power developed by the armature of a D.C motor is equal to: BLT –II
page 1028
a. armature current multiplied by back e.m.f
b. power input minus losses
c. power output multiplied by efficiency
d. power output plus iron losses
38. When external AC power is connected to TRU, its output: (Ref. EHJ Pallet, 63)
a. energies d.c. control relay circuits
b. is connected to d.c. bus bar to operate d.c. consumers
c. both a & b are correct
d. is used sparingly on ground
Page
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
b. current constant
c. power constant
d. Main flux constant
41. The effect of increasing the length of air-gap in an induction motor will be to increase the
:
BLT II Page 1309.
a. power factor
b. speed
c. Magnetizing current
d. air gap flux
6(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
42. In a very simple system, busbars are made up of : (Pallett- page 76 Chapter 5)
a. strips of interlinked terminals
b. thick metal strip
c. thick metal rod
d. Both (b) and (c)
45. Which one can be operated both manually and electrically: (Palette- Page 99 Chapter 6)
a. Proximity switch
b. Rotating switch
c. Micro-switch
d. Thermal switch
46. what indicates the number of circuits each pole can complete through the switch :
(Palette- Page 100 Chapter 6).
a. Pole
b. Throw
c. Both (a) and (b)
d. Bi-pole
Page
47. Method employed in CRT to generate free electrons: (BLT Chapter 73- Page 2695)
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
48. Mark the correct statement related to NPN Transistor: V.K Mehta Page 755
a. Collector is highly doped for supply of carrier
b. Base is least doped and has thin layer.
C. Emitter has relatively low voltage
49. White crystals on Ni-Cd battery is formed due to: ( Pallett Chap-01 – page 23 )
a. Over charging
b. Under Charging
c. Charge can be checked by voltage test
50. State of charge of Nickel Cadmium battery can be determined by: (Pallett- Chap- 01 Page
23)
7(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
a. Electrolytic level
b. By relative density of the electrolyte
c. Battery Voltage check
d. Battery voltage on-charge condition and the electrolyte should be at maximum level.
51. A non-return valve fitted in the air inlet prevents: (Pallett Chapter 01 Page 24)
a. air from cabin to enters the battery ventilation chamber and continues through to the
outside of the aircraft.
b. Fumes and gases from escaping into the aircraft when no pressure differentials exist
on the ground.
c. Leakage of battery fumes by pressure differential.
54. In order to achieve the best possible commutation, commutator are employed with: Pallett
page 7
a. A support ring, or end frame, that can be rotated to alter the position of the brushes
relative to the magnetic neutral axis.
b. brushes with short leads or "pigtails"
c. Flexible copper braid moulded into the brush during manufacture.
Page
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
a. Deep cycling
b. Fresh charge
c. Battery cycling
56. Mark the correct statement regarding landing horn: Pallett Page 176
a. Horn reset when thrust lever idle & flap position is up
b. horn reset when final phase of landing & flap down position
58. Which one is the most accurate type of frequency measuring instrument? FAA-Jeppessen
a. integrated circuit chip having a clock circuit
b. Electro dynamo meter using electromagnetic fields
8(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
59. Mark the correct statement about TRU and static inverter (pallet) Check!!!
a. TRU is connected to respective DC/AC busbar
b. Static inverter directly connected to battery
c. TRU connected to the battery
d. Static inverter connected to non-essential bus bars,
60. When both the inputs are high and Output are low: BLT
a. Positive NOR & Negative NAND
b. Positive OR & Negative AND
c. Positive NOR & Negative NAND
d. Positive NAND & Negative NOR
63. 8-Bit register that store the memory output when a memory read operation is performed, is known
as:
a. Program counter
b. Memory data register
c. Memory address register
d. Instruction register
Page
64. When a transformer designed for low frequency is used with higher frequency. Palltte 63
a. in this case the primary current will be reduced and the transformer will function normally
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
b. in this case the primary current will be high and there is a risk of excessive heat generation in the
primary winding and subsequent burnout.
68. MTCS:
a. When open circuit occur in a circuit, current return into the system
b. When short circuit occur current return to system
c. As in b) & voltage low level condition light brightness is low
9(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
d. As in b) and c)
69. The iron loss of a transformer at 400 Hz is low. Assuming that eddy current & hysteresis loss vary
as the square of flux
density. The iron loss of the Transformer at rated voltage but at 50 Hz would be-------- watt: BLT-
1209
a. 80
b. 640
c. 1.25
d. 100
73. In the case of split bus bar method: page 81 pallett Check!!!
a. Used between non-parallel generator
b. In the case both the generator fails the main DC busbar will become isolated from the essential DC
busbar
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
77. In a generator what eliminates possible sparking to the brush guide caused by the movement of the
brush within the
holder: FAA
a. Brush spring tensions.
b. The brush pigtails
c. Undercutting of the mica on the commutator
10(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
78. The voltage in an ac transformer that contains twice as many as loops as the primary will be: FAA
a. Greater & the amperage less than in the primary
b. Less & the amperage greater than the primary.
79. In the case of synchronous motor : Pallett page 143
a. F=PN/60 (P:no. of pairs of poles, N:synchronous speed, F: power-supply frequency )
b. b. F=60/PN
c. c. F=P60/N
81. When constant frequency generators are operating in parallel the shearing of a real load is
controlled by : pallet 221
a. Varying the excitation current in each generator
b. Varying the output speed of the CSD unit
c. By shedding certain load.
Page 11 of 11
82. The primary reason for providing compensating winding in a DC generator is to: BLT-965
a. Compensate for decrease in main flux
b. Neutralize armature mmf
c. Neutralize cross magnetizing flux
d. Maintain uniform flux distribution
83. The main function if interlope is to minimize ________between the brushes and the commutator
when the DC machine
is rotated: BLT-965
a. Friction
b. Sparking
c. Current
d. Wear and tear
Page
84. The moving system of an indicating type of electrical instrument is subjected to: FAA
a. A deflecting torque
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM
WWW.DGCAQUESTIONPAPERS.IN - (ES FEB 2015)
b. A controlling torque
c. A damping torque
d. All of the above
85. The meter suitable for only direct current measurement is: FAA
a. Moving-iron type
b. Permanent magnet type
c. Electromagnet type
d. Hot wire type
86. The ratio of the true power to the apparent power in an a.c circuit is known as: Pallett
a. Reactive power
b. Power factor
c. Real power
87. The phase voltage of a three phase star connected a.c generator is: Pallett
a. Equal to line voltage
b. Greater than line voltage
11(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers
[[{{ Dear Followers If you have previous year DGCA question papers or other useful data then you can
submit your question papers or data (with your name and details) here at ” aviatorslinks@gmail.com ” or
you can share on facebook also and help other students in their exam preparation. We will publish ur
document on our webpage with your name and details within 24 hr.
"You feel good because you're helping others, and the others feel good because they're getting help.”
We are not generating any type of revenue from this webpage this is only for helping aviators.
Share more n more document with us.
Thanks
Gud Luck
www.dgcaquestionpapers.blogspot.com ]]]}}
Page
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT AVIATORSLINKS@GMAIL.COM