Professional Documents
Culture Documents
How to configure two DHCP Servers using 2 swithces with 1 DSL. Keep in mind
we cannot use any other additional equipment.
View Question | Asked by : imz.ez
Answer Question Subscribe
There are four routhers and 4 swiches and 40 computers in an office. How will
you connect each devices and configure those devices?
Latest Answer: This is using different network build purpose, so connect first
router to first switch and connect 10 nodes with first switch, this is one
network ex:192.168.1.0 networkand connect second router to second switch
with 10 nodes this is another network ex:192.168.2.0 ...
Read Answers (2) | Asked by : ahmed12
Answer Question Subscribe
Read a Switch
You are given only the IP address of the switch but not the port number. How
will you read that switch?
Latest Answer: If the switch has an Ip address, you telnet to the switch and
provided that there is no password set either at virtual terminals or to enter
the privileged mode, you can enter privileged mode and write sh run and read
the running config. ...
Read Answers (2) | Asked by : ahmed12
Answer Question Subscribe
Network Negotiation
Answer Question Subscribe
Communicating
When two network layers are in communication with one another, these layers
are known as?a.)PDUsb.)peer entiiesc.)PRAMsd.)sockets
Latest Answer: b.) Peer Entities ...
Read Answers (2) | Asked by : chicago57
Answer Question Subscribe
WAP Gateway
Answer Question Subscribe
State the technical steps required for data transmission from server to server
via a router and switch
View Question | Asked by : baby mi
Answer Question Subscribe
Token Ring Segment
You need to connect a Token Ring segment to an Ethernet segment. Would you
use a router, a brouter , or a bridge ?
Latest Answer: Router is needed with two interfaces: one Token Ring, another
Ethernet one. ...
Read Answers (1) | Asked by : Metro2007
Answer Question Subscribe
TCP IP Integration
Answer Question Subscribe
Cable Length
Answer Question Subscribe
ISP Protocol
Which protocol is used to communicate between client and ISP?
Latest Answer: OSPF is used. Because it is considered to be the most efficient
IGP(interior gateway protocol). BGP is more widely used as exterior gateway
protocol(EGP). ...
Read Answers (2) | Asked by : AW Networks
Answer Question Subscribe
You have been given 1 printer and 1 IP Address for installing it in a Networking
EnvironmentHow will you do it?
Latest Answer: Go to the start menu - setting - printers and fax - add a printer -
local printer attached to this pc - create the new port - select the standard
tcp/ip protocol - and enter the ip address and insert the printer CD for driver
and install the printer ...
Read Answers (3) | Asked by : shamz.ek
Answer Question Subscribe
Windows crashed because NTLDR File is missing. How will you restore this file
(Without using Safe Mode Option)?
Latest Answer: Step 1Locate your windows xp/2000 install disk and place it in
your CD/DVD ROM drive. If you do not have this disk then you cannot proceed
any further.Step 2Restart your computer or turn it off then back on again.Step
3When the computer restarts press ...
Read Answers (7) | Asked by : shamz.ek
Answer Question Subscribe
IP V6 PING
How do you ping from one host to another in IPv6 without ARP?
Latest Answer: By using the Neighbour Discovery Protocol (NDP) ...
Read Answers (2) | Asked by : kcrao
Answer Question Subscribe
Answer Question Subscribe
Answer Question Subscribe
What is VLAN and INTERVLAN? Why do we use these techniques?What are the
differences between STP, RSTP and MSTP?
Latest Answer: VLAN are used to segment your network eliminate broadcast it is
also used for security purpose.VLAN of sales department cannot access VLAN of
finance department.InterVLANs are used to create VLAN to VLANs. ...
Read Answers (2) | Asked by : callnitin
Answer Question Subscribe
Latest Answer: It is a tool used to check and repair disk related errors like,1. Bad
Sector2. Partition Table3. Cross Link File4. Currup File etc. ...
Read Answers (2) | Asked by : ranjithkolaboina
Answer Question Subscribe
A person would like to access a file on another computer (connected via LAN)
while working with safe mode. What should he do?
Latest Answer: In safemode itself he can use telnet to access file on the other
system in the same LAN ...
Read Answers (2) | Asked by : rrsain
Answer Question Subscribe
Answer Question Subscribe