Professional Documents
Culture Documents
1. Design a current series feedback amplifier and determine the frequency response, gain
and bandwidth and calculate the input impedance and output impedance with and without
feedback. Assume IC = 1 mA, VRE = 1V, R2 = 10 KΩ, VCC = 12 V.
2. Design a voltage Shunt feedback amplifier and determine the frequency response, gain,
bandwidth and calculate the input impedance and output impedance. Assume I C = 1 mA,
VRE = 1V, R2 = 10 KΩ, VCC = 12 V.
3. Design and construct a RC phase shift oscillator to obtain the sine wave for a frequency
of 2 kHz, hfe=100
4. Design and construct an Integrator & Differentiator circuit and obtain the output
waveforms for the square and sine waveform as input.
5. Construct the following clipper circuit and obtain the corresponding output if the input is a
sine wave of 12 V (p-p).
(i) Positive clipper
(ii) Negative Clipper
6. Construct the positive clamper and negative clamper circuit and obtain the corresponding
waveform, if the input is a sine waveform and a square waveform of amplitude 10 V(p-p).
7. Design and construct a free running multivibrator to get an output square waveform and
calculate its TON and TOFF.
8. Design and construct a one-shot multivibrator to get an output pulse waveform and
calculate its TON and TOFF.
9. Design and construct a Hartley oscillator to get a sine wave output of 4.5 KHz frequency.
10. Design and construct a Colpitts oscillator to get a sine wave output of 9 KHz frequency.
11. Design and construct a class – C tuned amplifier for a resonant frequency of 7 KHz and
determine the frequency response of the amplifier.
Simulation Using PSPICE
1. Simulate a class c tuned amplifier circuit and obtain the corresponding waveform using
Pspice.
2. Simulate a Bistable multivibrator to get a square waveform using Pspice.
3. Simulate a Schmitt trigger and obtain the corresponding waveform for the sine wave
input using Pspice
4. Simulate a tuned collector circuit and obtain the corresponding waveform using Pspice.
5. Simulate a monostable multivibrator using Pspice
6. Simulate a Voltage time base generator using Pspice.
7. Simulate a Wein bridge oscillator and obtain the corresponding waveform using Pspice.
5. Study the drain and transfer characteristics of junction field effect transistor .
1. Design a current series feedback amplifier and determine the frequency response, gain,
bandwidth and calculate the input impedance and output impedance with and without
feedback. Assume IC = 1 mA, VRE = 1V, R2 = 10 KΩ, VCC = 12 V. (100)
2. Design a voltage series feedback amplifier and determine the frequency response, gain,
bandwidth and calculate the input impedance and output impedance. Assume I C = 1 mA,
VRE = 1V, R2 = 10 KΩ, VCC = 12 V. (100)
3. (i) Design and construct a RC phase shift oscillator to obtain the sine wave for a frequency
of 650 Hz. Assume C = 0.01 μF. (70)
(ii) Simulate a CMOS Inverter circuit and obtain the corresponding waveform for the
square wave input using Pspice. (30)
4. (i) Design and construct an Integrator circuit and obtain the output waveforms for the
square and sine waveform as input. (70)
(ii) Simulate a CMOS NOR circuit and obtain the corresponding waveform for the square
wave input using Pspice. (30)
5. (i) Design and construct a Differentiator circuit and obtain the output waveforms for the
square and sine waveform as input. (70)
(ii) Simulate a CMOS NAND circuit and obtain the corresponding waveform for the
square wave input using Pspice. (30)
6. (i) Construct a Wein bridge oscillator to obtain the sine wave for a frequency of 1 KHz. (70)
7. Construct the following clipper circuit and obtain the corresponding output if the input is a
sine wave of 12 V(p-p).
(i) Positive clipper (ii) Negative Clipper (iii) Biased positive clipper with V R = + 3V
(iv) Biased negative clipper with VR = - 3V (v) Combination clipper with VR1 = + 3V and VR2 = - 3V (100)
8. (i) Construct the positive clamper and negative clamper circuit and obtain the
corresponding waveform, if the input is a sine waveform and a square waveform of
amplitude 10 V(p-p). (70)
(ii) Simulate a Butterworth 2nd order low pass filter using Pspice. (30)
9. (i) Design and construct a free running multivibrator to get an output square waveform and
calculate its TON and TOFF. (70)
(ii) Simulate an Astable multivibrator to get a square waveform using Pspice. (30)
10. (i) Design and construct a one-shot multivibrator to get an output pulse waveform and
calculate its TON and TOFF. (70)
(ii) Simulate a monostable multivibrator to get a square waveform using Pspice. (30)
11. (i) Design and construct a Hartley oscillator to get a sine wave output of 12 KHz
frequency. (70)
(ii) Simulate a CMOS Inverter circuit and obtain the corresponding waveform for the
square wave input using Pspice. (30)
12. (i) Design and construct a Colpitts oscillator to get a sine wave output of 250 KHz
frequency. (70)
(ii) Simulate a CMOS NAND circuit and obtain the corresponding waveform for the
square wave input using Pspice. (30)
13. (i) Design and construct a Eccles – Jordan circuit to get an output square waveform and
calculate its TON and TOFF. (70)
(ii) Simulate a Bistable multivibrator to get a square waveform using Pspice. (30)
14. Design and construct a class – C tuned amplifier for a resonant frequency of 2 KHz and
determine the frequency response of the amplifier. (100)
15. Design a series shunt feedback amplifier and determine the frequency response, gain,
bandwidth and calculate the input impedance and output impedance. (100)
16. (i) Design and construct a low frequency oscillator with a ladder type feedback RC
network for a frequency of 650 Hz. (70)
17. (i) Construct the positive clamper and negative clamper circuit and obtain the
corresponding waveform, if the input is a sine waveform and a square waveform of
amplitude 10 V(p-p). (70)
(ii) Simulate a CMOS NOR circuit and obtain the corresponding waveform for the square
wave input using Pspice. (30)
18. (i) Design and construct an Astable multivibrator to get an output square waveform and
calculate its TON and TOFF. (70)
(ii) Simulate a free running multivibrator to get a square waveform using Pspice. (30)
19. Construct the following circuit and obtain the corresponding output if the input is a sine
wave of 12 V(p-p).
(i) Positive clipper (ii) Negative Clipper (iii) Positive clamper (iv) Negative clamper
(v) Combination clipper with VR1 = + 3V and VR2 = - 3V (100)
practically.
7. Measure the coupling factor of the given four port passive device
8. Measure the bending loss of the given fibre of a wavelength of radiation as 650nm.
9. Determine the Numerical aperture of the plastic fibre provider with the kit using