(F106_0)ADI-HDD ERROR: ILLEGAL DISK REPALCEMENT DETECTED (ADI HDD
EXCHANGE TO SATA HDD)
CLASIFICATION ERROR ITEM
OTHER SERVICE CALL ADI-HDD error: The ADI-HDD has been replaced illegally to SATA-HDD (normal type).
Check item Measures
Setting Check if the HDD has been replaced with a SATA-HDD (normal type). 1. Start the equipment in the 4C mode: [4] + [C] + [POWER] 2. Check the type of the HDD shown on the top left of the Control panel display "Current HDD type". 2a. In case of "SATA-HDD" (normal type), replace it with the original ADI-HDD or a new ADI-HDD. Notes: To replace with the original ADI-HDD, start the equipment in the normal mode and then reinstall system software only if any abnormality occurs. 2b. In case of "ADI-HDD" Check each item in the Measures field for the HDD below. If the error still occurs, reinstall the system software HDD • Connector check • Harness check Follow the procedure below if no abnormality is found in the check items above. 1. Start the equipment in the 4C mode: [4] + [C] + [POWER] -> 1. Revert factory initial status HDD 2. Reinstall the system software.
[F106_1] ADI-HDD error: HDD type detection error
Classification Error item
Other service call ADI-HDD error: HDD type detection fails.
Check item Measures Setting If the error is not recovered after rebooting the equipment or no abnormality is found on any check items for the HDD, Reinstall the system software HDD • Connector check • Harness check • Start the equipment in the 5C mode: [5] + [C] + [POWER] Check the file system and recover it if necessary. If the recovery fails, replace the HDD. If the equipment does not start in the 5C mode, also replace the HDD. • Check that either the ADI-HDD or SATA- HDD (normal type) is mounted. 1. Start the equipment in the 4C mode: [4] + [C] + [POWER] 2. Check the type of the HDD shown on the top left of the Control panel display "Current HDD type". Normal status: ADI-HDD or SATA-HDD Abnormal status: Unknown HDD If "Unknown HDD" is displayed, reinstall the system Software.
[F106_2] ADI-HDD error: ADI encryption key download operation error
Classification Error item
Other service call ADI-HDD error: Downloading of or
consistency check for ADIHDD encryption key fails.
Check item Measures
Setting Checking of ADI-HDD encryption key status 1. Start the equipment in the 3C mode: [3] + [C] + [POWER] 2. The authentication menu is displayed. Press [OK]. (Not required in the default setting) 3. Select "5. Key Backup Restore" and then press the [START] button. 4. Check the status of the ADI-HDD encryption key on the Key Backup Restore Mode menu. 5. After the operation is completed, shut down the equipment by pressing the [POWER] button. • In case both the SRAM ADIKey and FROM ADIKey status are OK Reinstall the system firmware. • In case either the SRAM ADI Key or FROM ADI Key status is other than OK Restore the ADI-HDD encryption key. • In case both of the SRAM ADI Key or FROM ADI Key status are other than OK Reinstall the system software.
[F106_3] ADI-HDD error: ADI authentication Admin Password generation error
Classification Error item
Other service call ADI-HDD error: The generation of ADI
authentication Admin Password fails.
Check item Measures
Setting Reinstall the system firmware. Reinstall the system software.
[F106_4] ADI-HDD error: Authentication random number generation error
Classification Error item
Other service call ADI-HDD error: The generation of a
random number for authentication data fails.
Check item Measures
Setting Reinstall the system firmware. Reinstall the system software.
[F106_5] ADI-HDD error: Authentication data transmission error
Classification Error item
Other service call ADI-HDD error: The transmission of
authentication data fails. Check item Measures Setting Reinstall the system firmware. Reinstall the system software. • In case this error occurred after returning SRAM data for SRAM cloning: Copy the ADI-HDD encryption key from FROM to SRAM. 1. Start the equipment in the 3C mode: [3] + [C] + [POWER] 2. The authentication menu is displayed. Press [OK]. (Not required in the default setting) 3. Select "5. Key Backup Restore" and then press the [START] button. 4. Select "6. ADIKey FROM to SRAM" and then press the [START] button. 5. After the restoring of the encryption key has completed, "Operation Complete" is displayed. 6. After the operation has completed, shut down the equipment by pressing the [POWER] button