Professional Documents
Culture Documents
Weldolet PDF
Weldolet PDF
George Anung
UIA/T/E/CMC
Topics Outline
Images Of Weldolet
Clarification
Traditional Branches
Evolution Of Traditional Branches
Definition
Clarification in Interpretation
Welding Requirement
Recent Events
Photos
2
Weldolet
3
Clarifications
An Olet: a generic name for an intergrally self-reinforced butt welded set-on branch connection.
The Olet and Weldolet trademark is owned by Bonney Forge
ASME, ANSI, MSS and API simply referred to them as ‘branch connection fitting’
4
Traditional Branches
5
Evolution Of Traditional Branches To Self-Reinforced Branches
6
Definition
Branch connection fitting’ defined as ‘an intergrally reinforced fitting welded to a run pipe and connected
to a branch pipe by a buttwelding, socket welding, threaded, or flanged joint; includes a branch outlet
fitting conforming to MSS SP-97’ (ASME B31.3-2006)
Groove weld’ defined as ‘the joint penetration (depth of bevel plus the root penetration when specified).
The size of a groove weld and its effective throat are the same’. (ASME B31.3-2008)
7
ANSI B31.3 Welding Requirement
328.5.4(d) Branch connections, including branch connection fittings which abut the outside of the run or
which are inserted in an opening in the run shall be attached by fully penetrated groove welds. The
welds shall be finished with cover fillet welds having a throat dimension not less than ........
8
ASME B31.3 Clarification in Interpretation No. 11-10, 1993
Question: In accordance with ASME B31.3-1990 Edition, para 304.3.3 (much early edition), may the
groove weld attaching an intergrally reinforced branch connection fitting to the run pipe be less than
fully penetrated, if the depth of the groove is greater than required for adequate branch?
reinforcement?
9
ASME B31.3 Clarification in Interpretation No. 13-11, 1994
Question: In accordance with ASME B31.3-1993 Edition, Addenda a, what is the effective weld throat
thickness required for a proprietary intergrally reinforced branch connection fitting?
10
Bonny Forge’s Requirement
Bonny Forge says ‘Particular care should be taken to weld only the bevel portion of the fitting. This
......... prevents the erroneous practice of welding up to the rib on the skirt’.
11
Bonny Forge General Instruction
Drawings showed welding from root right up to the edge of weld bevel plus reinforcement
12
MSS SP-97 Welding Requirement
Para. 1.2: Fittings manufactured to this Standard Practice are designed to make a fully reinforced
branch connection in accordance with applicable piping code requirements, when attached, at an
opening in a run pipe by means of a full penetration weld
13
ANSI B31.8 Welding Requirement
831.41(j) The branch shall be attached by a weld for the full thickness of the branch or header wall plus
a fillet weld, ......
14
ASME B31.3 Clarification in Interpretation No. 22-22, 2006
Question: In accordance with ASME B31.3-2006 Edition, when para. 328.5.4(d) is applied to proprietary
integrally reinforced branch fittings, does the term fully penetrated groove weld describe a weld that fills
to the manufacturer’s weld line or to the top of the groove if no weld line is present?.
Reply: Yes. See definition of groove weld under size of weld in para. 300.2. See also interpretation 13-11
15
Recent Events
CILIPADI PROJECT
CPDR-A : 39 F23R-A : 87
F28 PROJECT
F28DR-A : 57 F6 : NONE REPORTED YET
16
Photos-incomplete welding
17
Photos - Good Weldolet Welding joint (after repair)
18
Questions
19
Thank You!
The End
20
Q&A
21