Professional Documents
Culture Documents
650V eGaN HEMT短路特性研究 PDF
650V eGaN HEMT短路特性研究 PDF
2
2020 年 2 月 Advanced Technology of Electrical Engineering and Energy Feb. 2020
张 英1 , 秦海鸿1 , 彭子和1 , 修 强1 , 荀 倩2
(1. 多电飞机电气系统工业与信息化部重点实验室, 南京航空航天大学, 江苏 南京 211106;
2. 查尔姆斯理工大学, 瑞典 哥德堡 999034)
器件在短时间内流过数倍于额定电流的短路电流,
1 引言
因此为了保证 eGaN HEMT 的正常使用,提高变换
作为新型宽禁带半导体器件之一,氮化镓高电 器的 可 靠 性, 需 要 充 分 认 识 eGaN HEMT, 特 别 是
子迁移率晶体管( Gallium Nitride High Electron Mob- 650V 电压等级 eGaN HETM 的短路原理和短路特
ility Transistor,GaN HEMT) 比 Si 器件具有更低的导 性,探究电 路 参 数 对 其 短 路 特 性 的 影 响, 为 eGaN
通电阻、更快的开关速度和更高的结温工作能力,将 HEMT 的短路保护设计、驱动电路设计和变换器整
其作为制作电力电子变换器的功率器件有望显著提 机设计提供帮助。
高变换 器 的 最 高 工 作 频 率、 效 率, 降 低 体 积、 重 研究人员已对 Si IGBT 和 Si MOSFET 等 Si 基功
量 [1-5]
。 增强型氮化 镓 高 电 子 迁 移 率 晶 体 管 ( En- 率器件的短路特性有了较为充分的认识 [12-14] 。 近
hancement Gallium Nitride High Electron Mobility 年来,科研工作者也开始对 SiC MOSFET 的短路特
Transistor, eGaN HEMT) 由于其常断特性和众多的 性进行研究 [15-17] 。 由于 eGaN HEMT 独特的平面型
应用功率等级(15 ~ 650V、3. 4 ~ 120A) [2] ,受到了广 结构和导 通 机 理, 原 有 的 研 究 结 果 很 难 直 接 用 于
泛关注,研究人员已研制出了多种基于 eGaN HEMT eGaN HEMT。 目前针对 600 / 650V 电压等级的 GaN
的变换器,涵盖了无线电能传输、电机驱动、光伏发 HEMT 的短路特性研究还比较少。 文献 [ 18] 对不
电等领 域 。 然 而, 在 实 际 应 用 中, eGaN HEMT
[5-10]
同母线电压和关断电压 650V 常通型 GaN HEMT 的
的开关速度较快,栅极阈值电压较低( <2V) ,桥臂电 短路特性进行了探究。 文献[ 19] 探究了不同母线
路中高速开关时,可能会由于桥臂串扰现象,导致桥 电压下 600V GaN GIT 的短路特性,并提出了提高
臂误导通问题 ,此外变换器、负载等都可能会发 [11]
GaN GIT 短路能力的建议。 文献[ 20] 探究了 100V
生故障,出现短路现象。 这些都会导致 eGaN HEMT eGaN HEMT 对脉冲电流的承受能力,但并未指出其
收稿日期: 2018-11-30
基金项目: 国家自然科学基金项目(51677089) 、 中央高校基本科研业务费专项资金项目( NJ20160047) 、 江苏省研究生
科研与实践创新计划项目( KYCX18_0287)
作者简介: 张 英(1993-) , 男, 河北籍, 硕士研究生, 研究方向为新型宽禁带半导体器件的特性及其应用;
秦海鸿(1977-) , 男, 江苏籍, 副教授, 博士, 研究方向为功率变换技术、 电机控制、 新器件应用研究。
张 英,秦海鸿,彭子和,等. 650V eGaN HEMT 短路特性研究[ J] . 电工电能新技术, 2020,39(2) :10-20. 11
di D 时间较短,热量集中于管芯附近,很难通过外部的仪
U Lstray = L stray (1)
dt 器探测到管芯温度变化,通常会对器件进行建模,构
式中,L stray 为功率回路中从输入电容到被测器件之 建热网络模型,将短路过程中芯片上的耗散功率施
间的杂散电感;i D 为漏极电流。 加在对应的热网络模型中,获取不同条件下的结温。
此时 eGaN HEMT 的漏源电压 U DS 为: 图 3 为 制 造 商 提 供 的 热 网 络 模 型 及 结 构, eGaN
U DS = U DC - U Lstray (2) HEMT 的热网络模型分为四层,分别为 GaN 层、 Si
如图 2( b) 所示,短路电流上升过程中,上升速 衬底、连接层和铜基底。 表 1 列出了每一层的热阻
率 di D / dt 不断下降,寄生电感 L stray 的感应电压逐渐 R θ 、热容 C θ 及对应的时间参数 τ。
降低,漏源电 压 U DS 逐 渐 回 升, 当 短 路 电 流 达 到 峰
值,即漏极电流处于饱和值时,漏源电压达到稳定
值。
阶段 2[ t 1 ,t 2 ] :t 1 时刻短路电流达到最大值,在
此之后短路电流迅速下降,t 2 时刻下降至峰值电流
的 1 / 2 处。 由于短路电流峰值较高,此阶段内 eGaN
HEMT 的结温迅速上升,eGaN HEMT 的沟道电子迁
移率与结温呈较强的负相关关系( T -k ,T 为结温,k
为温 度 系 数 ) , 即 结 温 越 高, 沟 道 电 子 迁 移 率 越
图 3 eGaN HEMT 热网络模型及其结构
低 [21] 。 由于结温的升高,电子迁移率降低,导通电 Fig.3 Thermal model of eGaN HEMT
阻迅速上升,短路电流快速下降。 同时随着短路时
间的增加,栅源电压出现明显的下降,表明栅极电流 表 1 eGaN HEMT 热网络模型参数
I G 有所上升,这是因为随着沟道温度的上升,穿过 Tab.1 eGaN HEMT thermal model parameters
栅源极间绝缘介质层的电场逐渐加强。 热阻 R θ 热容 C θ 时间常数
位置
/ ( ℃ / W) / ( ( W·s) / ℃ ) τ / ms
阶段 3[ t 2 ,t 3 ] :此阶段内由于结温仍在升高,导
GaN 层 0. 03 2. 12×10 -5 6. 36×10 -4
通电阻继续上升,短路电流持续下降,但是由于此时
Si 衬底 0. 487 1. 48×10 -3
0. 72
短路电流已经下降至较低值,因此结温上升速率变 连接层 0. 441 3. 33×10 -4 1. 47
缓,导通电阻和短路电流的变化速率也减慢。 栅源 铜基底 0. 042 5. 04×10 -4
0. 21
电压 U GS 仍在继续下降,到 t 3 时刻,栅源电压下降至
5. 4V,栅极电流约为 35mA,GS66504B 栅极电流的 由表 1 可知,GaN 层热阻容的时间常数最小,仅
典型值为 80μA, 此 时 栅 极 电 流 约 为 典 型 值 的 437 有 0. 636μs,Si 衬底和连接层热阻容时间常数达到
倍。 了 ms 级别,而 eGaN HEMT 的短路耐受时间一般为
阶段 4[ t 3 ,t 4 ] :t 3 时刻,eGaN HEMT 关断,短路 几十微秒 [21] ,意味着短路过程中产生的热量扩散到
电流下降,di D / dt 为负,与功率回路中的寄生电感 外界前,短路过程已经结束,因此可以认为短路测试
L strap 相互作用感应出与直流母线电压极性相同的电 中管芯与外部环境保持绝热状态,短路过程中产生
压,令 eGaN HEMT 漏源电压出现尖峰。 t 4 时刻后 的热量完全在管芯上。
eGaN HEMT 完全关断,短路过程结束。 图 4 是利用 LTSpice 软件对 eGaN HEMT 短路
t 0 ~ t 4 时间内,eGaN HEMT 导通产生的能量损 过程的仿真结果,其中母线电压设置为 300V,驱动
耗即为短路能量 E C ,可表示为: 电阻为 20Ω,驱动电压为 6V。 可以看到漏极电流的
∫u
t4 变化趋势与实验结果相同,短路故障发生时,漏极电
EC = i dt
DS D (3) 流迅速上升,峰值约为 60A,达到饱和峰值后,短路
t0
改变开通驱动电阻对关断过程中漏极电流和漏源电
压几乎没有影响,但是短路过程结束时栅源电压会
随着 R G( on) 的增大而降低。 开通驱动电阻从 10Ω 上
升到 30Ω,短路过程结束时栅源电压从 5. 6V 下降
至 5. 2V,对应的栅极电流从 40mA 下降至 31mA,这
主要是因为随着开通驱动电阻上升,短路能量略有
下降,结温略有降低,栅源极间电场强度减弱。
图 5 不同直流母线电压 U DC 下的 U DS 、U GS 和 I D
短路波形
Fig.5 Short circuit waveform of U DS ,U GS and I D
for different DC bus voltages
图 7 不同关断驱动电阻 R G( off) 下的 U DS 、I D 和 U GS
短路波形
Fig.7 Short circuit waveform of U DS , I D and U GS
for different R G( off)
4. 3 驱动电压 图 8 不同栅源驱动电压 U GS 下的 U DS 、I D 和 U GS
实验中直流母线电压设置为 300V,开通驱动电 短路波形
阻 R G( on) 取为 20Ω,关断驱动电阻 R G( off) 取为 15Ω, Fig.8 Short circuit waveform of U DS , I D and U GS
驱动电压分别取为 4V、5V 和 6V。 图 8 为不同驱动 for different U GS
电压下的 U DS 、I D 和 U GS 的短路波形,可以看到栅极
驱动电压对 eGaN HEMT 短路电流影响比较明显。 4. 4 参数影响分析
开通过程中,随着驱动电压的上升,开通速度加快, 为了 更 加 深 入 地 探 究 各 电 路 参 数 对 eGaN
短路电流上升速度变快,从 4V 上升到 6V 时,di D / dt HEMT 短路特性的 影 响, 对 各 参 数 与 短 路 电 流 峰
从 0. 625A / ns 上升到 1A / ns,同时短路电流峰值也 值 I D( peak) 、关断 时 短 路 电 流 值 I D( off) 、 关 断 时 漏 源
出现明显上升,由于短路电流上升更快、峰值更高, 电压过压 ΔU DS 和短路能量 E C 的关系进行了量化
自发热更严重,驱动电压为 6V 时,短路电流上升至 分析。
16
电工电能新技术 第 39 卷 第 2 期
Bandgap Power Devices and Applications [ C] . Knoxville, phase-leg topology [ A ] . 2015 IEEE 3rd Workshop on
TN, USA, 2014. 24-29. Wide Bandgap Power Devices and Applications ( WiPDA)
[ 2 ] 李媛, 马 红 波, 柯 玉 连 ( Li Yuan, Ma Hongbo, Ke [ C] . Blacksburg, VA, USA, 2015. 98-103.
Yulian) . 基于 GaN HEMT 的高效率、 高功率密度 LLC [12] Lefebvre S, Khatir Z, Saint-Eve F. Experimental behavior
谐振变换器的设计 ( Design of high efficiency and high of single-chip IGBT and COOLMOS devices under repeti-
power density GaN-based LLC converter) [ J] . 电工电能 tive short-circuit conditions [ J] . IEEE Transactions on E-
新技术 ( Advanced Technology of Electrical Engineering lectron Devices, 2005, 52 (2) : 276-283.
and Energy) , 2018, 37 (10) : 58-64, 88. [13] Fuhrmann J, Klauke S, Eckel H. IGBT and diode behav-
[ 3 ] Millan J, Godignon P, Pernina X, et al. A survey of wide ior during short-circuit type 3 [ J] . IEEE Transactions on
bandgap power semicondutor devices [ J] . IEEE Transac- Electron Devices, 2015, 62 (11) : 3786-3791.
tions on Power Electronics, 2014, 29 (5) : 2155-2163. [14] Wu R, Wang H, Pedersen K B, et al. A temperature-de-
[ 4 ] 黎晓, 马红波, 庞亮 ( Li Xiao, Ma Hongbo, Pang Li- pendent thermal model of IGBT modules suitable for cir-
ang) . 基于 SiC MOSFET 的无桥 Boost PFC 变换器研究 cuit-level simulations [ J] . IEEE Transactions on Industry
与设计 ( Research and design of SiC MOSFET based du- Applications, 2016, 52 (4) : 3306-3314.
al-Boost bridgeless PFC rectifier) [ J] . 电工电能新技术 [15] Nguyen T, Ahmed A, Thang T V, et al. Gate oxide relia-
( Advanced Technology of Electrical Engineering and En- bility issues of SiC MOSFETs under short-circuit operation
ergy) , 2018, 37 (10) : 65-70. [ J] . IEEE Transactions on Power Electronics, 2015, 30
[ 5 ] 巴腾飞, 李艳, 梁美 ( Ba Tengfei, Li Yan, Liang Mei) . (5) : 2445-2455.
寄生 参 数 对 SiC MOSFET 栅 源 极 电 压 影 响 的 研 究 [16] Sun J, Xu H, Wu X, et al. Short circuit capability and
( The effect of parasitic parameters on gate-source voltage high temperature channel mobility of SiC MOSFETs [ A] .
of SiC MOSFET) [ J] . 电工技术学报 ( Transactions of 2017 29th International Symposium on Power Semiconduc-
China Electrotechnical Society) , 2016, 31 (13) : 64-73. tor Devices and IC’ s ( ISPSD) [ C] . Sapporo, Japan,
[ 6 ] 郑心城, 陈为 ( Zheng Xincheng, Chen Wei) . 电动汽车 2017. 399-402.
无线 充 电 的 磁 耦 合 结 构 综 述 ( Overview of magnetic [17] 秦海鸿, 徐克峰, 王丹, 等 ( Qin Haihong, Xu Kefeng,
coupling structure in wireless charging for electric vehi- Wang Dan, et al.) . SiC MOSFET 短路特性 ( Short cir-
cle) [ J] . 电气技术 ( Electrical Engineering) , 2017, cuit characteristics of SiC MOSFET) [ J] . 南京航空航
18 (4) : 9-15. 天大学学报 ( Journal of Nanjing University of Aeronau-
[ 7 ] Zhang L, Born R, Zhao X, et al. A high efficiency invert- tics & Astronautics) , 2018, 50 (3) : 348-354.
er design for Google little box challenge [ A] . 2015 IEEE [18] Huang X, Lee D Y, Bondarenko V, et al. Experimental
3rd Workshop on Wide Bandgap Power Devices and Ap- study of 650V AlGaN / GaN HEMT short-circuit safe oper-
plications ( WiPDA) [ C] . 2015. 319-322. ating area ( SCSOA) [ A] . 2014 IEEE 26th International
[ 8 ] Zhang X, Yao C, Lu X, et al. A GaN transistor based Symposium on Power Semiconductor Devices & IC’ s
90W AC / DC adapter with a Buck-PFC stage and an isola- ( ISPSD) [ C] . Waikoloa, HI, USA, 2014. 273-276.
ted quasi-switched-capacitor DC / DC stage [ A ] . 2014 [19] Fernández M, Perpina X, Roig J, et al. P-GaN HEMTs
IEEE Applied Power Electronics Conference and Exposi- drain and gate current analysis under short-circuit [ J] .
tion - APEC 2014 [ C] . 2014. 109-116. IEEE Electron Device Letters, 2017, 38 (4) : 505-508.
[ 9 ] 王旭 东, 朱 义 诚, 赵 争 鸣, 等 ( Wang Xudong, Zhu [20] Ray W B, Schrock J A, Bilbao A V, et al. Analysis of
Yicheng, Zhao Zhengming, et al.) . 驱动回路参数对碳 GaN power MOSFET exporsure to pulsed overcurrents
化硅 MOSFET 开关瞬态过程的影响 ( Impact of gate- [A] . 2015 IEEE Pulsed Power Conference ( PPC) [ C] .
loop parameters on the switching behavior of SiC MOS- Austin, TX, USA, 2015. 1-5.
FETs) [ J ] . 电 工 技 术 学 报 ( Transactions of China [21] Li H, Li Xiao, Wang X D, et al. E-mode GaN HEMT
Electrotechnical Society) , 2017, 32 (13) : 23-30. short circuit robustness and degradation [ A] . 2017 IEEE
[10] Li H, Zhang X, Zhang Z, et al. Design of a 10kW GaN- Energy Conversion Congress and Exposition ( ECCE )
based high power density three-phase inverter [ A] . IEEE [ C] . Cincinnati, OH, USA, 2017. 1995-2002.
Energy Conversion Congress and Exposition [ C] . 2016. [22] Aminbeidokhti A, Dimitrijev S, Han J, et al. The power
1-8. law of phonon-limited electron mobility in the 2-D electron
[11] Jones E A, Wang F, Costinett D, et al. Cross conduction gas of AlGaN / GaN hetero structure [ J] IEEE Transac-
analysis for enhancement-mode 650V GaN HFETs in a tions on Electron Devices, 2016, 63 (5) : 2214-2218.
20
电工电能新技术 第 39 卷 第 2 期
ZHANG Ying 1 , QIN Hai-hong 1 , PENG Zi-he 1 , XIU Qiang 1 , XUN Qian 2
(1. Center for More-Electric-Aircraft Power System, Nanjing University of Aeronautics
and Astronautics, Nanjing 211106, China;
2. Chalmers University of Technology, Göteborg 999034, Sweden)
Abstract: eGaN HEMT has great application prospect due to the ability to significantly enhance efficiency and pow-
er density of converters. However, unintended turn on caused by cross talk or short circuit in load may cause eGaN
HEMT to withstand large current in these applications. Thus, in order to ensure the safety and reliability of eGaN
HEMT power devices in the overload and short circuit, etc, it is important to explore the short circuit principle and
characteristic of eGaN HEMT, and the influence of circuit parameters on short circuit characteristics. In this paper,
the short circuit test platform is established to analyse the short circuit process of eGaN HEMT. Then, the eGaN
HEMT thermal network model is used to analyze the junction temperature during the short circuit, and explores the
effects of different junction temperature on the short circuit characteristics. Furthermore, the influence of different
circuit parameters on the short-circuit characteristics is studied and compared to reveal the key factor influencing
short circuit characteristics, which provides some guidance for the design of short circuit protection of eGaN HEMT.
Key words: E-mode GaN HEMT; short-circuit characteristics; short-circuit protection; temperature dependence