Professional Documents
Culture Documents
Is 11559 1995 PDF
Is 11559 1995 PDF
( Reaffirmed 2005 )
Indian Standard
HYDRAULIC FLUID POWER - CYLINDERS - ROD
END SPHERICAL EYES - MOUNTING DIMENSIONS
( First Revision )
0 BIS 1995
NATIONAL FOREWORD
This Indian Standard which is identical with IS0 6982 : 1992 ‘Hydraulic fluid power- Cylinders - Rod
end spherical eyes - Mounting dimensions’, issued by the International Organization for Stand-
ardization (ISO), was adopted by the Bureau of Indian Standards on the recommendation of Hydraulic
Fluid Power Systems Sectional Committee and approval of the Production Engineering Division
Council.
This Indian Standard was first published in 1985 and was based on IS0 6982 : 1982 ‘Hydraulic fluid
power - Cylinders - Rod end spherical eyes - Mounting dimensions’. Consequent upon the revision
of above IS0 standard, the sectional committee dealing with the subject decided to revise the Indian
Standard by adopting the revised IS0 standard under dual numbering system.
The text of the IS0 standard has been approved as suitable for publication as Indian Standard without
deviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention
is particularly drawn to the following :
a) Wherever the words ‘International Standard’ appear referring to this standard, they should be
read as ‘Indian Standard’.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice
is to use point (_) as the decimal marker.
CROSS REFERENCES
In the adopted standard reference appears to certain International Standards for which Indian Standards
also exist. The corresponding Indian Standards which are to be substituted in their respective place
are listed below along with their degree of equivalence for the editions indicated :
IS0 286-2 : 1988 IS0 system of limits IS 919 ( Part 2 ) : 19931150 286- Identical
and fits - Part 2 : Tables of standard 2 : 1988 IS0 systems of limits
tolerance grades and limit deviations and fits : Part 2 Tables of stand-
for holes and shafts ard tolerance grades and limit
deviations for holes and shafts
(first revision)
IS0 3320 : 1987 Fluid power system IS 8208 : 1976 Sizes for cylinder Technically
and components -Cylinder bores and bores and piston rod diameter for equivalent
piston rod diameters - Metric series fluid power systems
IS0 5598 : 1985 Fluid power systems IS 10416 : 1992/lSO 5598 : 1985 Identical
and components - Vocabulary Fluid power systems and com-
ponents - Vocabulary
Indian Standard
HYDRAULIC FLUID POWER -CYLINDERS - ROD
END SPHERICAL EYES -MOUNTING DIMENSIONS
( First Revision)
m
t 1
2
L
IS 11559 : 1995
IS0 6982 : 1992
5 General requirements since movement will occur between the shaft and
the bearing bore and lubrication should be carried
out through the shaft.
5.1 Material
6.2 Fitting
5.1.1 Rod end spherical eyes shall be made of
material having a minimum yield point Rp,,2 of
250 N/mm* and an elongation at rupture, ,4 min., of 6.2.1 The specified tilting angle of rt 4” can still be
at least 12 %. obtained when the clevis inner faces abut the side
faces of the inner ring of the spherical plain bearing.
5.1.2 The radial spherical plain bearings mounted
in the rod ends shall be made of steel with a mini- 6.2.2 The rod end spherical eye shall be screwed
mum surface hardness of 50 HRC firmly against the piston rod shoulder before locking.
All cross-sections shall be selected so that, under A rod end spherical eye with a bore of CN = 25 mm
the maximum tensile load produced by the cylinder, and steel on steel surfaces shall be designated as:
the yield strength of the material used for the rod
end is at least 2.5 times the maximum tensile load. Rod end IS0 6982 - 25
Annex A
(informative)
Bibliography
[I] IS0 6099:1985, Fluid power systems and components - Cylinders - Identificafion
code for mounting di-
mensions and mounting types.
4
(Continued from second cover)
.._ technirsl
The .-- z-._ committee
-- . . . . d- .--~-“-.-‘-
resnonsihle ._. the
for ..._ T._T _._.._.. of this &n&grf
nrenaretion has reviewed the rnrovisions
- ---
of following IS0 standards and has decided that they are acceptable for use in conjunction with this
standard: .
IS0 3322 : 1985 Fluid power systems and components - Cylinders - Nominal pres-
sures
IS0 6022 : 1981 Hydraulic fluid power - Single rod cylinders - Mounting dimensions
- 250 bar (25 000 kPa) series
IS0 6099 : 1985 Fluid power systems and components - Cylinders - Identification
code for mounting dimensions mounting types
IS0 6124-2 : 1982 Spherical plain radial bearings, joint type - Boundary dimensions -
Part 2 : Dimension series EW, bearings with extended inner ring