Professional Documents
Culture Documents
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router1
Router1(config)#interface fastEthernet 0/0
Router1(config-if)#ip address 128.100.24.1 255.255.255.192
Router1(config-if)#no shutdown
Router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router1(config-if)#exit
Router1(config)#interface serial 0/0/0
Router1(config-if)#ip address 10.10.10.1 255.255.255.252
Router1(config-if)#no shutdown
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router2
Router2(config)#interface fastEthernet 0/0
Router2(config-if)#ip address 128.100.24.65 255.255.255.224
Router2(config-if)#no shutdown
Router2(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router2(config-if)#EXIT
Router2(config)#interface serial 0/0/0
Router2(config-if)#ip address 10.10.10.18 255.255.255.252
Router2(config-if)#no shutdown
Router2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
Router2(config-if)#EXIT
Router2(config)#interface serial 0/0/1
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router>ENA
Router>ENAble
Router#CONF
Router#CONFigure TER
Router#CONFigure TERminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router3
Router3(config)#interface fastEthernet 0/0
Router3(config-if)#ip address 128.100.24.97 255.255.255.240
Router3(config-if)#no shutdown
Router3(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router3(config-if)#EXIT
Router3(config)#interface serial 0/0/0
Router3(config-if)#ip address 10.10.10.2 255.255.255.252
Router3(config-if)#no shutdown
Router3(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
no shutdow
Router3(config-if)#EXIT
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router3(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
interface serial 0/0/1
Router3(config-if)#EXIT
Router3(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
OSPF R1
Router1>ENA
Router1>ENAble
Router1#CONF
Router1#CONFigure TER
Router1#CONFigure TERminal
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#router ospf 1
Router1(config-router)#network 128.100.24.0 0.0.0.63 area 0
Router1(config-router)#network 10.10.10.0 0.0.0.3 area 0
Router1(config-router)#network 10.10.10.16 0.0.0.3 area 0
Router1(config-router)#END
OSPF R2
Router2>ENA
Router2>ENAble
Router2#CONF
Router2#CONFigure TER
Router2#CONFigure TERminal
Enter configuration commands, one per line. End with CNTL/Z.
Router2(config)#router ospf 1
Router2(config-router)#network 128.100.24.64 0.0.0.63 area 0
Router2(config-router)# network 10.10.10.16 0.0.0.3 area 0
Router2(config-router)#network 10.10.10.8 0.0.0.3 area 0
01:16:57: %OSPF-5-ADJCHG: Process 1, Nbr 128.100.24.1 on Serial0/0/0 from
LOADING to FULL, Loading Done
Router2(config-router)#END
Router2#
%SYS-5-CONFIG_I: Configured from console by console
OSPF R3
Router3>ENA
Router3>ENAble
Router3#CONF
Router3#CONFigure TER
Router3#CONFigure TERminal
Enter configuration commands, one per line. End with CNTL/Z.
Router3(config)#router ospf 1
Router3(config-router)#network 128.100.24.96 0.0.0.63 area 0
Router3(config-router)#network 10.10.10.0 0.0.0.3 area 0
Router3(config-router)#
01:19:36: %OSPF-5-ADJCHG: Process 1, Nbr 128.100.24.1 on Serial0/0/0 from
LOADING to FULL, Loading Done