he.
‘in bees Ne
— F Cr SRHEge
Pauses
Lumeros Heat Resisting Aluminium Paints
USES
Furnace equipment, reaction vessels, hot metal stacks, kins, ues, exhaust systems, hot pipes and similar
areas exposed to dry heat attack,
‘SCOPE
High performance aluminium coatings based on silicone resin for protection of steel at elavated temperatures
bbetwaan 250° C and 600°C.
We oer three different qualities of Lumeros depending on temperature ranges ~ HR/47, 123HR & HAV123,
PRODUCT DATA
‘Type : Single Pack
‘Composition Siicone resin and aluminium
‘Application : Brush or Conventional Spray
Recommended DFT: 15-20 microns per coat
‘Theoretical Spreading Rate :
HRI? B123HR —:7.0-9.0Sq, Mtr/Ltr
HRIIAS 16.0-21.0 Sq. MirfLtr
Drying Time
TOUCH :3-6hous
‘Curing : Alter application of the final coat of Lumeros.
HR Alumioium, alow the system to air dr for minimum
24 hrs. under ambient concitions. The tomporature is
then to be gradually increased to the working
temperature range for obtaining optimum performance,
‘Overcoating Interval
MIN Overnight
ESS
Chemical Resistance :
EXPOSURE SPLASH AND. «MILD FUMES
SPILLAGE OUTDOOR RESISTANOE
acids Fair Good
‘Akals Fair Good
‘Solvents Poor Good
Sait Good Very Good
Water Excellent Excellent
‘Temperature Resistance :
Continuous: HR/47 = 260-400°
Y23HR :250-800°C
HR/43 : 400-600" C
Flash Point : Above 25°C
‘Colour : Aluminium
Packing :20 Lirs.and 4 Lirs.
‘Thinnee/Cleaner : Thinner 853
Finish : Bright Metalic
‘Storage Life : Upto twelve months as long as the
‘Sealed containers are kept under cover in a dry place
‘Under normal temperature conditions.Le iach Midah dh cdhh ab lsae
Lumeros Heat Resisting Aluminium Paints
Sa
Fomove grease, cil and other contaminants preferably by using Bison Degreasing Solvent. Blast clean to a minimum
of S 21/2 Swedish Standard SIS 05 5900 with a surface protle not exceeding 95-40 microns.
I blasting is not practical, make ful use of mechanical tools along with manual chipping and wire brushing to remove
loose rust and scale to St. 2 Swedish Standard SIS 05 5900. Excessive burishing of steel isto be avoided.
“Thoroughly dust down al surfaces.
“The surface should be clean and dry before application ofthe appropriate primer or HR Aluminium Paint.
fr tna orl omar hg
ean Ais Soc tein i acenia
Conventional Spray : Add maximum upto 5% Thinner 853 depending on conditions.
Use any suttabe standara equipment at an atomising pressure of 2.8 ~ 3.5 Kg/om?.
and coat sed Coat
ee
Steel ‘Lumeros 123 HR Lumeros 123 HR -
(250-5000)
Si coc) WNWOSHRVKG Lamas VS -
Notes:
4. Application must be eared out on cold surface only,
‘Aor the final coat has cried completly, the painted surface may be gradually heatod.
2.0 not apply when temperature falls below 10°C or rises above 50° C and wien relative humidity rises above 90%.
Do not apply during rai, fog or mist.
3. For heat resistance upto 400° G, Zine Anode 308 can act as a primer coat which is to be applied on
blast cleaned surtaces,
4. Itis preferable to measure the actual skin temperature for selecting the right quality of Lumeros HR Paint Coating
Health & Safety : Please refer to the Separate Safety Data sheet available with detalied information.
DISCLAIMER
‘The infmaton contained within ths Data Shoot based on feito boeved tobe rele a the pr
{i of preperation. ne Company il at be lacs for oe x damoge howsoever casas eluding pa
Tat fer negligence, which may be sere bythe user of te data cortanes hers is he uses poked
responedaity to cond al nacacsary touts Got tho siutabily of any proc! sytem forth
Intec use. No quarares of resus s mple since conten of sear beyond ou cota
BERGER PAINTS INDIA LIMITED
Bergr House, 129 Park Stat, Kokata 700017 Phono : (038) 2228 9724 ines] /2249 9754 (4 nos) Fax: 91-33-2049 9729 /2249 9000
Email: WORTH bp okh@mantraaline.com SOUTH: ball ch@siy.com EAST: bplcli@venknet WEST: bpiLush@vsnl.net