Professional Documents
Culture Documents
New Tender Basis PDF
New Tender Basis PDF
OFT
ENDERDOCUME
NTS
BI
LLOFQUANT I
TIE
S
FORPROPOSEDI NTERI
ORL AY
OUT
AND
T E
CHNICALSPECIFI
CATI
ONSF OR
F
LOORING,CARPE NTRY
,GLAZING,
F
ABRI
CAT
IONWORKS ,P
AINTING,SUSPENDEDFALSECE
ILI
NG,
MODUL ARFURNIT
URE ,POWDE RCOATI
NG
NAT
IONALCENT
REFORSUS
TAI
NABL
E
COAST
ALMANAGE
ME NT
ANNAUNI
VERS
ITY
,CHE
NNAI
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
a Rates quoted must have full compliance with the following including the cost of grey cement, and white cement.
b The owner reserves the right to supply or issue price basis for any material item.
c The owner reserves the right to 'lend' his name for all imported items in order to avail any possible duty exemptions and the said benefit shall go
to the owner.
d The items which are supplied free of cost need to be reconciled at the end of the project based on material constants.
e Special attention to be paid to Technical specifications.
f Basic rate shall not include all taxes, delivery, handling charges, wastage & delivered at site.
g Contractors should factor in their prices for power and water etc. Space will be provided at site for stores but contractor will be responsible for
and maintenance of the same.
h With respect to any brans / makes specified in this document, Contractor is permitted to quote for equivalent brand / make and is to provide
details of the same.
Notes: The contractor is to note and allow the following preambles in his scope of work.
f. All exposed vertical laminated surfaces shall be finished with 1.0mm thick laminate of approved make shade unless otherwise specified.
g. All exposed veneer shall be group matched natural cut plain veneer of approved make and shade.
h. All exposed veneered, wood surfaces shall be finished with matt melamine polish to approved shade.
I. All exposed edges of plywood, blockboard etc shall be finished with 3mm thick lipping beading of specified wood.
j. All plywood, blockboard for office areas shall be water resistant, termite/borer proof commercial grade of specified make.
k. All plywood, blockboard for wet areas (toilets/pantry) shall be termite/borer proof and waterproof marine grade of specified make.
l. Timber used shall be kiln seasoned and should be free from shrinkage, warpage even after fabrication of furniture.
m. Provision to be made for additional supports and reinforcement that may be required for stability and evenness at where curved partition is
constructed.
n. Contractor to make provisions of all necessary scaffoldings to facilitate high level installations.
o. Contractor to form openings on partition for services and to seal gaps using silicon sealant.
p. Where the use of spring loaded auto closing hinges is specified, the same shall be installed strictly as per manufacturers guidelines and relevant
tools required for the same.
q. All items to have sample approved prior to commencement of mass production.
r. All screws seen out side should be star SS.
s. Contractor to use the following screws unless otherwise specified.
For partition frame work : 16/8 no. sheet metal screw 16mm in length.
For partition anchoring on floor & true ceiling : 75/10 no. sheet metal screw 75mm in length.
1 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
b All finished flooring shall be covered with plaster of Paris of 6mm thick over a plastic film without any extra cost till handing over to the Owner.
c. Daily housekeeping of work areas which includes segregation of debris like cement based, plastic, glass, wood and collecting in containers
provided to/by you, at an acceptable location inside the site premises.
d. Granite slabs should be free of all defects and all grains / patterns shall be properly matched from the same lot. Any colour / lot variation shall
be rejected.
e. The minimum quality benchmark will be decided by the Owner / Project management consultant / Architect based on mock up samples
before commencing the work.
f. Unless otherwise specified the rates quoted shall be inclusive of the following ~ Cost of material, taxes, transport, labour, overheads and profit,
etc.,
g. The basic rate of granite/marble includes supply, taxes and delivery to site, delivered and unloaded to the point of cutting, the same. All granite
material shall be "gang saw water cut".
h. No wastages shall be paid for seperately. The same shall be factored in the quoted rate.
I. If there is a reduction is the basic rate the cost for the same shall be adjusted pro rata in the quoted rates. No increase in basic rates shall be
allowed without written approval from the Architect.
j. Base sub-grade/sub-floor to be prepared by cleaning all dust/loose particles, caked mortar droppings, etc by scrubbing with steel wire brushes.
Surface to be roughened if so required and surface cleaned with water and kept wet for minimum 12 hours.
k. Bedding layer of mortar to be provided as directed in the case of 19mm+ slabs to correct level, step as instructed.
l. Finished work to be inclusive of cutting and polishing where specified/applicable.
m Contractor to be responsible for hiring/operating of all machines/equipment. Approval to be obtained from Project Management consultant
before operating.
n Finished floor must be cured by keeping wet for atleast 1 week after installation.
o Flooring to be cleaned, waxed or acid washed where applicable and as directed.
p Pointing to be done using matching coloured grout as specified/directed.
q All marble flooring/slabs to be polished using tin oxide only.
r Slurry for marble flooring to be of white cement only.
s In the instance of granite/marble floors, the contractor has to obtain prior approval on dry laying. Wet laying to be carried out only on approval.
Not extra cost shall be paid for dry laying.
2 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Note:
The following is the list of approved make/brand against each product. Where more than one brand has
been specified, the names are given in order of preference. Contractor is to quote rates based on the
materials of 'first preference' after ascertaining availability, delivery schedules and other parameters
affecting delivery. Unless the Contractor stipulates to the contrary in his tender, it shall be assumed that the
rates quoted are for materials of first preference.
VENDORS
SL.NO. ITEM DETAILS
CONFIRMATION
2 PLYWOOD CENTURY
COMMERCIAL GRADE
ARCHID PLY
GREEN PLY
APPROVED EQUIVALENT
GREEN PLY
APPROVED EQUIVALENT
ASIS
APPROVED EQUIVALENT
3 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
5 DECORATIVE GREENLAM
LAMINATES
MERINO
ARCHID
CENTURY
APPROVED EQUIVALENT
JACKSON
URO
APPROVED EQUIVALENT
ASAHI
SAINTGOBAIN
APPROVED EQUIVALENT
BERGER
APPROVED EQUIVALENT
4 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
ASIAN
BERGER
APPROVED EQUIVALENT
SPECTRUM HERITAGE
APPROVED EQUIVALENT
ICI
APPROVED EQUIVALENT
WOOD GUARD
APPROVED EQUIVALENT
LIGHT HOUSE
SHEENLAC
APPROVED EQUIVALENT
GEZE
ASSABLOY
APPROVED EQUIVALENT
5 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
GEZE
ASSABLOY
APPROVED EQUIVQLENT
ASSABLOY
APPROVED EQUIVQLENT
ASSABLOY
APPROVED EQUVALENT
HAFELE
APPROVED EQUVALENT
GEZE
ASSABLOY
APPROVED EQUVALENT
6 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
GEZE
ASSABLOY
APPROVED EQUVALENT
ASSABLOY
APPROVED EQUIVALENT
ASSABLOY
APPROVED EQUIVALENT
7 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
GEZE
APPROVED EQUIVALENT
33 SCREWS
JOINERY WORKS NETTLEFOLD IS 1365, GI
screws
HARDWARE, FITTINGS SS STAR HEAD SCREW AS
PER MANUFACTURERS
SPECIFICATION
APPROVED EQUIVALENT
KURLON
APPROVED EQUIVALENT
NITCO
ASIAN
8 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
APPROVED EQUIVALENT
APPROVED EQUIVALENT
BIRLA WHITE
APPROVED EQUIVALENT
LUMAR
ULTRAMARK
APPROVED EQUIVALENT
39 COMPOSITE ALUCOBOND
ALUMINIUM INTERIOR
GRADE ( 3MM THICK )
TIMEX BOND
APPROVED EQUIVALENT
UP TWIGA
KIMCO
APPROVED EQUIVALENT
9 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
GEZE
APPROVED EQUIVALENT
ICI
BERGER
APPROVED EQUIVALENT
APPROVED EQUIVALENT
INDAL
APPROVED EQUIVALENT
DIAMOND FRAMES
APPROVED EQUIVALENT
PALLADIO
APPROVED EQUIVALENT
10 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
CORAMANDLE
BIRLA
APPROVED EQUIVALENT
51 RMC ULTRATECH
ACC
CORAMANDLE
APPROVED EQUIVALENT
JINDAL
SAIL
APPROVED EQUIVALENT
JINDAL
SAIL
APPROVED EQUIVALENT
11 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
SL.
DESCRIPTION OF WORKS AMOUNT IN RS.
No.
4.00 CARPET
8.00 CHAIRS
9.00 BLINDS
10.00 SIGNEAGE
12 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
SUMMARY SHEET
SL.
DESCRIPTION OF WORKS AMOUNT IN RS.
No.
3.00 PARTITION
4.00 DOORS
13 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
DATE : 12.12.2013
BILL OF QUANTITIES FOR INTERIOR FIT OUT
Quoted rate to include the cost of curing, protection with polythene sheet and POP overlay till hand-over.
Quoted rate to include the cost of Chipping and removing the Existing Flooring , along with shifting the Debris
from Site
(Basic cost of the Al skirting to be considered at 325/rmt including tax, including installation
14 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Providing and fixing Suspended False Ceiling which includes Gypsum Plaster board 12mm thk., False Ceiling on 24
gauge G.I. frame work which includes Providing. & fixing G.I. perimeter channels 0.55 mm thk 20mmx30mm,web
size 27mm along perimeter of ceiling, screw fixed to brick wall/partition with nylon sleeves & screws @ approx 2'0"
c/c. Suspending G.I. intermediate channels size 45 mm,0.9 mm thk, flanges of size15mm each from the soffit
1220mm c/c with ceiling angle 25 x10mm x 0.55mm thk fixed to soffit G.I. cleat & steel expansion fasteners.
Ceiling section of 0.55mm thk having web of 51.5mm & flanges 26 mm each lips 10.5 mm fixed to intermediate
channel with connecting clips & perpendicular to int channel @ 457mm c/c.12.5 mm tapered edge Plaster
board ( IS 2095-1982 ) screw fixed to ceiling section with 25mm dry wall screws @ 230 mm c/c. Boards to be joint
& finished so as to have flush look including filling finishing edges with jointing compound paper tape/cloth
gauze & 2 coats of primer suitable for plaster board. Rate to include M.S.framing around A/C ducts where ever
necessary.
Rate to include cove to profile, cut-outs for light fixtures, spot lights, smoke detectors, Pelmets, Vertical risers as
shown in dwg. and all services cut outs as required. complete as directed by Project manager / Architect.
Note: for Light fittings, Grills, diffusers and other cut-outs have to be made with a frame of perimeter channels of
size 20mm x 27mm x 30mmx 0.55mm thk, supported suitably. Quoted rate shall also to include the Engineered
system made up of primary sections in galvanized steel of 21x35x3600mm in 0.75 bmt gauge. with top cross rails
and the system shall be used at 1200mm apart where direct suspenders cannot be used due to over head
ducting or any other services.
Mode of measurement : Finished plan ceiling area shall be measured for payment. Any vertical height upto
450mm to be included with the scope which wont be calculated seperately
3.00 PARTITION
Contractor to make provision for fixing all electrical, networking boxes formed out of 12mm thick ply boxing
screwed onto partition framework at required heights/levels as directed.
Mode of measurement : Length & height (upto true ceiling) shall be measured for payment.
15 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Contractor to make provision for all electrical, networking boxes which shall be installed on 25mm x 25mm x
1.2mm thick extruded aluminum "L" angle screwed onto partition framework at required heights/levels as
directed.
Mode of measurement : Length & height ( up to true celing ) shall be measured for payment.
Quoted rate shall include providing 12mm X 25mm Aluminum L-Angle & grooves where ever necessary as per
detail dwg.
Mode of measurement : Length & height shall be measured for payment. Location : For floating Storage
cladding
Considered basic price for ply = 44/Sqft ( excluding taxes )
Mode of measurement : Length & height shall be measured for payment. Location : Writing board
Contractor to polish / chamfer the edges of the glass & seal the joints between glass with clear silicon sealant.
The cost to include providing & Fixing frosted film to the glass as per the design of the Architect's.
Mode of measurement : Length & height up to False ceiling shall be measured for payment.
16 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Cost to include provididng and fixing 6mm Aluminium "U"Channel @1200mm interval as per the drawing and
instructions of the Architect
Mode of measurement : Length & height up to False ceiling shall be measured for payment.
Note : Factory Finished with Clip on System will be preferred.
Consider Basic cost of Laminate @ Rs. 290/sqm
Mode of measurement : Installed wall paper shall be measured in length & height for payment.
17 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
The color of the tile maintained even in long term exposure to sunlight (over 4th grade in 240 hrs at 100°C).
The surface of the tile is resistant to surface wetting (rate of resistance to surface wetting: 99.6%) therefore
inhabitation of
Furthermore, thevarious
panelgerms
can be and molds
easily cutisinto
inhibited.
any desired shape.
Consider Basic cost of Acoustic Panel @ Rs. 3010/sqm ( Excluding taxes )
Mode of Measurement : Cladded area will be measured for payment.
18 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
4.00 DOORS
4.01 SINGLE LEAF SINGLE SWING HONEY COMB FLUSH DOOR WITHOUT FRAME
a) Opening size: D1 - 1000mm X 2400mm ( Location : meeting rooms , trainning rooms, pantry, store, gym , music nos -
etc )(Vision panel - 100 x 950)
Shutter : Fabricating & fixing single leaf single swing flush door 33mm thk with honeycomb core of 25mm and
4mm prelaminated MDF on both sides of approved make, The shutter edges have a 25 x 75 mm pine wood
frame with 6 x 33 mm wooden edge binding
Hardware : one no SS mortise lock of " Dorma /Geze/ Ingersol rand " with , 4nos ss bearing hinges of Haffle/
Union make , 1 no exposed door closure of approved make, one no floor mounted SS door stopper.
Frame : No frame . The shutter to be fixed to the portal with fixing details as shown in the detailed dwgs
4.02 SINGLE LEAF SINGLE SWING FLUSH DOOR WITH FRAME Nos 66.00
a) Opening size: D2 - 1100mm X 2400mm (Vision panel - 100 x 950) Nos 4.00
Shutter : Fabricating & fixing single leaf single swing flush door 38mm thk of approved make, finished with 1mm
thick laminate of approved make & colour on both sides. The shutter edges shall be lipped in 8mm thick
approved timber beading melamine polished.
Hardware : one no SS mortise lock of Dorma / Geze / Equiv with , 4nos ss bearing hinges of Dorma/ Geze make ,
door closure of aproved make, one no floor mounted SS door stopper.
Frame : Frame should be formed out of 50mm X 100mm approved timber melamine polished with 38mm wide x
12mm deep rebate.
Fixing of Frame : Frame should be fixed to masonry wall using M.S holdfast / for partitions using wooden screws
with clear anti-termite treatment for the conceled portion frame.
Hardware : one no SS handle from outside and dead latch from inside Dorma/ Geze make ,
Shutter : Providing & fixing glass door mounted over approved Glass Hinges . The shutter to be formed out of
12mm thick clear toughened glass. The glass shutter should be polished on the edges.
Hardware : DORMA Hardware’s like, one no’s floor mounted SS bush of approved make, floor spring(BTS 84 of
Dorma make) with spindle of Dorma / approved make. Top patch with pivot of Dorma / approved make,
bottom patch with pivot of Dorma / approved make, cost also to include door stopper, complete as per the
details and instructions of the Architect.
Hardware : DORMA Hardware’s like, two no’s floor mounted SS bush of approved make, floor spring(BTS 84 of
Dorma make) with spindle of Dorma / approved make. Top patch with pivot of Dorma / approved make,
19 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Opening size: - D11: 1500mm X 2400mm (With vision panel of wired glass of 10mm thk) - Double Leaf nos 1.00
Opening size: - D5 : 1100mm X 2400mm (With vision panel of wired glass of 10mm thk)- - Single Leaf nos 30.00
Providing and fixing in position Fire Rated Metal door with pressed steel frame and shutter as per manufacturer ’s
details and as mentioned in the drawings including fixing ironmongery etc of MPP System Schroders make. This
includes providing and fixing brush steel finished iron mongery like Ball bearing Hinges, Mortise Locks, Handles,
Push Plates, Bolts, Door Closer, etc. (Dorma/ Geze/ Ingersoll /Shakti rand make) as indicated in the detail
drawings and all surfaces of doors shall be finished with 2 coats of Fire rating paint over a coat of primer to
achieve the fire rating as indicated in the detail drawings.
The door finished Fire retardant polish, steel pressed shutter with 2 Hour Fire rating of Single Shutter and vision
panel . Complete as per design and instructions of the Architects.
Shutter: The shutter of the Electrical trap door to be formed out of 25mm thick commercial ply finished in 1mm .
thick approved laminate on both sides. The edge of the shutter to be lipped with 8mm thick approved timber
beading finished in approved automotive paint.
Frame: The frame to be formed out of 50mm X 50mm approved timber finished in approved automotive paint
supported with 50mm X 50mm timber frame work from true ceiling.
Hardware: Approved SS butt hinges of approved make, 1no. Duct lock of approved make each shutter, tower
bolt of approved make.
Frame: The frame to be formed out of 50mm X 50mm approved timber finished in approved automotive paint
supported with 50mm X 50mm timber frame work from true ceiling.
Hardware: Approved SS butt hinges of approved make, 1no. Duct lock of approved make each shutter, tower
bolt of
Cost toapproved make.
include provididng and fixing 5mm Aluminium "U"Channel in Vertical position as per the drawing and
instructions of the Architect
Providing & fabricating 450mm deep floating storage formed out of 19mm thick MDF finished in 1mm thick
approved laminate consisting of storage with shutter, & 1mm thick approved laminate inside. The shutter of the
storage shall be formed out of 19mm thick MDF finished in 1mm thick approved laminate on the external side.
with 1mm thick approved laminate on the inside mounted over spring loaded auto closing hinges of approved
make, tower bolt. The Storage to accomodate Shelf made of 19mm thk MDF finished with approved laminate
as per the dwg .The exposed edges of the storage shall be lipped using approved timber beading formed to
shape melamine polished, complete as per detail dwg. & Architects instruction.
Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-
closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary
tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos.
chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos.
heavy duty SS ball catch, 100mm C type brushed SS handle
Mode of measurement : Length & height of the storage shall be measured for payment.
20 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Providing & fabricating 450mm deep storage formed out of 19mm thick MDF finished in 1mm thick approved
laminate consisting of shelves without shutter, & finished with 1mm thick approved laminate on all sides . The
storage to have 50 mm recessed skirting The exposed edges of the storage shall be lipped using approved
timber beading matching to the laminate, complete as per detail dwg. & Architects instruction.
Mode of measurement : Length & height of the storage shall be measured for payment.
21 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Low height cabinet to be topped with 20mm thick approved Granite counter sandwitched at the edge to
form a fascia of 40mm thick affixed to carcass with exposed edge profiled full round and polished to high gloss
with 1.2mm thick. X 50mm height skirting formed out of 19mm thk marine ply & finished in 1.2mm thick SS brushed
finish sheet as per detail dwg.
Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-
closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary
tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos.
chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos.
heavy duty SS ball catch, 100mm C type brushed SS handle. Th shutter to be cladded with 6mm thk Toughned
Glass with approved colour vinyl Backing with necessary fixture
Low height cabinet to be topped with 20mm thick approved Granite counter sandwitched at the edge to
form a fascia of 40mm thick affixed to carcass with exposed edge profiled full round and polished to high gloss
with 1.2mm thick. X 50mm height skirting formed out of 19mm thk marine ply & finished in 1.2mm thick SS brushed
finish sheet as per detail dwg.
Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-
closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary
tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos.
chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos.
heavy duty SS ball catch, 100mm C type brushed SS handle. Th shutter to be cladded with 6mm thk Toughned
Glass with approved colour vinyl Backing with necessary fixture
22 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Providing & fabricating laminated storage 450mm depth formed out of 19mm thick commercial ply with open
shelves. All the Shelves and internal surfaces to be finished in 1 mm tk laminate . Both outer exposed vertical
sides of the storage to be finished in 4mm thick Veneer and all other exposed external surafgaces to be
finished in 1 mm laminate The storage shall be provided with shelve formed out of 19mm thick approved
laminate finished in 1mm thick approved laminate, edges of the shelves shall be finished in 1mm thick approved
laminate. The shelves of the storage shall be mounted using approved SS adjustable pins. The exposed edges of
the storage shall be lipped using approved timber beading formed to shape melamine polished. complete as
per detail dwg. & Architects instruction. Ht=2400mm . The storage to have sharing intermediate vetical wall.
Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-
closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary
tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos.
chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos.
heavy duty SS ball catch, complete as per the drawing / instructions of the Architect.
23 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Table top: Table top of 750 mm wide to be formed out of of 19mm thick commercial ply clad with 6mm thick
approved Corian, complete as per detail dwg. & Architect's instruction.
Modesty panel: Modesty shall be formed out of 19mm thick commercial ply boxing finished in 6mm thk approved
Veneer Finish from outside and 1 mm tk laminate from inside. Provision for Cove lighting to be done as per dwg
Complete as per detail dwg. & Architects instruction. Cost to include providing & fixing 6mm thk SS inlays as
shown in the drawing.
Storage Unit : Providing and fixing Pedestal unit 2 nos of 620mm X 550mm X 650mm ht. made out of 19mm thk
Commercial Ply finished with 1mm thk approved laminate . Drawer unit to have 2 drawers and 1 shutter made
out of 19mm thk commercial ply finished with approved 1mm thk laminate , mounted on approved drawer
channel, central locking, approved handle. Complete as per the detailed dwg and instructions of the
Architect.
Transaction Counter : 20mm tk Transaction Counter to be made up of commercial finished with 12mm thk
approved Corian as per the detailed desing & instuctions of the Architect.
Consider Basic cost of 6mm Corian @ Rs. 7000/sqm
Consider Basic cost of 12mm Corian @ Rs. 13450/sqm
Table top: Table top of 650 mm wide to be formed out of of 19mm thick commercial ply clad with laminate on
the top and edges and with approved laminate below the table top , complete as per detail dwg. &
Architect's instruction.
Modesty panel: Modesty Panel 900mm high shall be formed out of 19mm thick commercial ply boxing finished in
1mm thk approved Laminate finish from outside & from inside .as shown in the drawing.Provision for Cove
lighting to be done as per dwg Complete as per detail dwg To have 50mm high recessed Al Skirting per dwg
Complete as per detail dwg. & Architects instruction.
Storage Unit : Providing and fixing Mobile Pedestal unit1no of Size 620mm X 550mm X 650mm ht. made out of
19mm thk Commercial Ply finished with 1mm thk approved laminate . Drawer unit to have 4 nos drawers made
out of 19mm thk commercial ply finished with approved 1mm thk laminate , mounted on approved drawer
channel, central locking, approved handle. Complete as per the detailed dwg and instructions of the
Architect.
Modesty panel: Modesty Panel 900mm high shall be formed out of 19mm thick commercial ply boxing finished in
1mm thk approved Laminate finish from outside & from inside .as shown in the drawing.Provision for Cove
lighting to be done as per dwg Complete as per detail dwg To have 50mm high recessed Al Skirting per dwg
Complete as per detail dwg. & Architects instruction.
Consider Basic cost of Laminate @ Rs. 290/sqm Mode of measurement Running length
Providing and Fabricating Board room Table in 40mm tk block board finished in approved white Leatherite
laminate
Table top: The table top to be formed out of 19mm thick commercial ply cladd using white leatherite
laminate. The edge of the table to be provided with same laminate finish The top to house cable trough for
cable management with 19mm thk ply openable as per details, complete as per detail dwg.
Base: The base of the table shall consist of 19mm tk commercial ply boxing finshed in laminate with 4mm groove
with foam backingwith 50mm SS skirting as shown in the dwg, complete as per detail dwg.
24 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
25 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Side table -Providing & fabricating 2 NOS OF side table of size 400 X 400X400 MM formed out of 19mm thick
commercial ply finished in 1mm thick approved laminate with edge lipping. The base shall be formed out of
50mm square Brushed finish SS support, complete as per detail dwg. & Architect's Instruction
Table top: The table top to be formed out of 19mm thick Prelaminated MDF, complete as per the Dwg or
instructions of the Architects.
Base: The base of the table shall consist of SS legs fabricated using, 25mm square SS pipe sections framed
together by welding tie bracers below the table top, complete as per the dwg & the instructions of the
Architects.
Providing and spray painting of enamel paint on the service ducts of approved shade as per drawings /
directions & manufacturer specification.
26 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Providing & fabricating storages formed out of 19mm thick commercial ply finished in 1mm thick approved
laminate. The top shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate,
exposed edge of the table shall be lipped using approved Edge Binding. The shutter of the storage shall be
formed out of 19mm thick ply frame and 5mm thk Glass with wooden beading allround, finished in 1mm thick
approved laminate.
Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-
closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary
tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos.
chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos.
heavy duty SS ball catch, complete as per the drawing / instructions of the Architect. Cost also to include
provididng and fixing SS Hookes to hang key bunches complete as per the instructions of the Architect .
Mode of measurement : Length & height of the storage shall be measured for payment.
Consider Basic Cost of Acoustic panel @ Rs 1720/ sqm And basic cost of fabric @ 300/Rmt
27 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Providing & supplying of medium size white color pebbles as per the instructions of the Architect
28 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Providing 15mm thick plastering in single coat with cement morter 1:3 to block masonry including rounding off
corners whereever required, smooth rendering with lime, providing and removing scaffolding, including the cost
of materials, labour, curing complete as per specifications.
29 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
-
8.08 HOUSE KEEPING LS 1.00
Providing house-keeping support with General House keeping for the entire site including clearing of wastes out -
of the premesis in regular basis inclusive of all dedicated labour and supervisory personnel at all times of work,
across the entire facility. Cost to include all equipment, consumables, protective and safety measures, etc.
complete. The site shall be kept clean to the complete satisfaction and based on instructions from the Project
Managers.
30 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
DATE : 12.12.2013
Mode of measurement : Length & height up to False ceiling shall be measured for payment.
Shutter : Providing & fixing glass door formed out of 10mm thick clear toughned glass. The glass should be polished on the
edges.
Hardwares to be used
Door Closure
GEZE - TS 3000/Dorma - TS 92/Assabloy - YDC 3025
Note - Door When opened should lock @ 90 deg.
Door Hinges - Dorma / Geze / Assaabloy/Propreitory
Door handle : 2 sets of 600 mm high and 22mm dia. Dorma/ Geze/ Assabloy
Corner patch Lock ( Dorma/ GEZE/ Assabloy )
Note:
Tolerence of Door from Floor should be Maximum 4mm
Saddle Plate to be Provided as per the Access Control Requirement
SS floor Stop
31 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
a) Opening size: D8 - 900mm X 2400mm (With Vision Panel 75 X 900mm) nos 11.00
b) Opening size: D12 - 1000mm X 2400mm (With Vision Panel 75 X 900mm) nos 1.00
Supply & Fixing of Single Leaf Flush door. Door frame formed out of Standard Sections as per Manufacturers
Specification.Complete as per details and instructions of the Architect.
Shutter : Fabricating & fixing single leaf single swing flush door 42mm thk of apporved make, finished with 1mm thick
laminate of approved make & colour on both sides. The shutter edges shall be lipped in 8mm thick approved timber
beading melamine polished.
Hardwares to be used
Concealed Door Closure
GEZE - Boxer 224
Dorma - TS 92
Assabloy - Yale YIC5124HO Concealed Cam Action Power Adjustable Door closer, Size 2-4, Hold Open, Silver
32 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Supply & Fixing of Single Leaf Flush door. Door frame formed out of Standard Sections as per Manufacturers
Specification.Complete as per details and instructions of the Architect.
Shutter : Fabricating & fixing single leaf single swing flush door 42mm thk of approved make, finished with 4mm thick
veneer of approved colour on both sides, melamine polished . The shutter edges shall be lipped in 8mm thick approved
timber beading melamine polished.
Hardwares to be used
Concealed Door Closure
GEZE - Boxer 224
Dorma - TS 92
Assabloy - Yale YIC5124HO Concealed Cam Action Power Adjustable Door closer, Size 2-4, Hold Open, Silver
Hardwares to be used
Concealed Door Closure : 2 seats of door closure GEZE - Boxer 224/ Dorma - TS 92/Assabloy :Yale YIC5124HO
33 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Door handle : 2 sets of 600 mm high and 22mm dia. Make : GEZE /DORMA / ASSABLOY
Dead lock : ( Dorma/ GEZE/ Assabloy )
Accessories
Note:
Tolerence of Door from Floor should be Maximum 4mm
SS floor Stop
34 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management Anna University , Chennai
OWNER : NCSCM
General Notes:
Scope - Work shall include the furnishing of all materials, equipment and labour to install the complete ceiling system.
It is the contractors/suppliers responsibility to ensure that materials delivered to the installation site are safeguarded from the time of their purchase until
they hand over the finished ceiling. It is desirable to store materials in a flat, clean, dry and secure space.
Ceiling system shall be installed by a sub-contractor thoroughly experienced with this type of installation and approved by the manufacturer. The
contractor to inspect premises prior to commencement of work and verify that the building is ready for installation.
Dust and loose particles should be removed by brushing or with a vacuum cleaner. Any pencil marks etc can be removed using ordinary pencil eraser.
All damaged tiles to be replaced by the contractor.
Spot lights and other luminaires should not be supported by or on the ceiling tiles.
Suspension wire must always be mechanically pre-straightened prior to use and should not be less than 2mm dia.
The Modular Ceiling tiles which are removed for the installation of other service works shall be given back to the owner.
The Vendor has go through the co-ordinated service drawings to enable them to understand better the needs for additional engineered supports from
the structural slab for supporting their Grid supports at no extra cost, wherever wide ducts and services run. Minor changes in the locations of services
have been considered.
35 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Rate Amount
Sl.No. DESCRIPTION Unit Qty
(Rs.) (Rs.)
General requisites
Grids width: 15mm plain Tee grid finished in approved shade. The main Runners & cross
Tees to have "stab" installation system made of corrosion-protected high tensile steel OR
approved equivalent.
Tile specification :
Tile type: Lay-in ceiling type
Tile size: 600mm X 600mm X 15mm thk.
Edge detail: Square Edge
Light reflectance: up to 0.90 ( 90% )
Humidity resistance: 95% RH
Color: White similar to RAL 9010
Surface burning characters: Class1, BS 476:Part 7:1987
Smoke Developed: 0 & Flame Spread = 5 as per UL
Thermal conductivity: 0.052 - .057 W/mk
NRC: 0.5/0.6
Thikness/Weight : 4.5 Kg/m2
CAC: 34 dB
Surface Pattern : Plain with random perforations
Ceiling Suspension System
Proprietary supplied ceiling suspension system to consist of 2mm or 3mm GI suspension
rod/wire with adjustable adjustable threaded "J" bolt of 3mm dia securely affixed to
structural ceiling using soffit angle fixing bracket and 10mm dia hook type anchor fastener.
Ceiling suspension system to be fixed at interval (grid) of 1200mm in both directions.
Proprietary supplied Grid System to consist of Main Runners @ 600mm and joined by Cross
Tees @ 600mm to form overall grid opening of 600mm x 600mm. Additional cross tees are
to be placed where appropriate for light fixtures, AC diffusers.
The grid system used shall be hot dipped galvanized steel sections, with exposed surfaces
chemically cleaned and capped prefinished in high - gloss polyester enamel with two
coat system on cold rolled steel.
36 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Rate Amount
Sl.No. DESCRIPTION Unit Qty
(Rs.) (Rs.)
Grid member sizes
Main runners : 15mm X 40mm X 0.38mm
Cross tees : 15mm X 40mm X 0.38mm
Perimeter section : 14mm X 20mm X 0.43mm
False ceiling will be measured on horizontal plane only. Horizontal plane measurements
are to be inclusive of all vertical drops, edge moldings, fascias, etc.
Rate quoted to include all cut-outs required for light fixtures, smoke detectors and other
services cut-outs complete as directed by Architect.
37 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
Date : 12-12-2013
General Note :
1 Scope - Work shall include the furnishing of all materials, equipment and labour to install the complete Carpet system with the manufacturer's approved
adhesive.
2 It is the Vendor's / supplier's responsibility to ensure that materials delivered on site is on the decided date by the project team & it is safeguarded from
the time of his purchase until he hands over the finished flooring. It is desirable to store materials in a pred-decided flat, clean and dry surface.
3 Carpet floor shall be installed by a thoroughly experienced vendor and the type of installation shall be as per manufacturer's specifications. The Vendor
shall inspect the premises prior to commencement of work and verify that the building is ready for installation.
4 Carpets to be laid as per the pattern indicated on drawing. All octroi ,frieght & handling to be accounted for and no additional amount shall be paid
for the same. Rate to be inclusive of covering of carpet with 125 micron single layer plastic cover & sealing of joints with tape. Any pencil marks etc.,
shall be removed using ordinary pencil eraser. All damaged portions to be replaced free of cost.
5 It is the Vendor's / supplier's responsibility to check the area of the each type of flooring material before placing the order.
6 Areas like partitions thickness or columns that is not carpeted shll not be included in the payable costs.
Rate Amount
Sl.No. DESCRIPTION Unit Qty
(Rs.) (Rs.)
38 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Rate Amount
Sl.No. DESCRIPTION Unit Qty
(Rs.) (Rs.)
Providing & laying carpet tile with following specification:
Style: Tile carpet
Construction : Tufted Textured Loop
Fiber Product: 100% Solution Dye PP
Gauge: 39.4/10cm. (1/12)
Finish Pile Thickness: 7.49mm +/- 0.5
Production yarn weight: 20 oz
Dye Method: 100% solution Dyed
Primary backing: Action Back
Tuft Bind: As per ASTM Standards
Delamination Strength: As per ASTM Standards
Static Control: As per ASTM Standards
Soil retardant: Protek
Anti-Microbial:Alphasan Built in Protection
Moisture Control: Yes
Electrostatic propensity: less than 3.5KV-Permanent Cond
Flammability( Radient Panel ASTM-E-662): >_0.45 ( Class I)
39 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
Date : 12-12-2013
40 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
DW1 Soiled Dish Landing Table with Chute 1500 X 600 X 850 MM Ht 1
41 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
DW4 Clean Plates Landing & Wiping Table with U/S 1500 X 700 X (850+150) MM Ht R/o
42 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
Date : 12-12-2013
43 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
CENTRE TABLE CIRCULAR TABLE - Providing and Fixing Corian Table top , with
8 4.00
750mm dia SS Base as per the Image attached.
44 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Add ED @ ________%
45 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
DATE : 12.12.2013
The panel in front of table top shall be of 8mm thk Laminated Glass as per detail dwg. The panel to have MS Powder coated bottom frame as per
manufacturers specs . The side panel shall be Detachable / slidable Panel made of 12mm thk Magnetic soft board wrapped with approved Fabric with
MS Powder coated frame as per manufacturers specs. Refer Drawing for Details.
The ends of the table top to be supported by Storage made of size 1350 mm x 450mm x 450mm Made of 19mm thk Prelaminated Partical Board as per
manufacturers specs. This will include understructure support made of MS Powder coated tubular section of the workstation. The Top of the Storage to be
provided with 50mm thk foam wrapped with approved Fabric as shown in the dwg.
Providing & Fixing CPU Holder underneath the table of Size 180 x 420 x 370mm made of MS powder caoted Sheet with Side perforation Panel for
Ventilation . Complete with all necessary hardwares.as shown in the dwg and instructions of the Architect.
46 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Base: The base of the table shall consist of MS Powder coated legs with panel below the table top as per manufacturers spec and Powder coating
match with the legs provided for the workstation, with levellers complete as per detailed dwg.
Side Storage unit: The table to consist of side storage unit of size 3200 mm X 450 mmX 1200mm consisting filing cabinet with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
Front Storage unit: The table to consist of Front storage unit of size 1370mm x 450mm x 1200mm consisting filing cabinet with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation,
with levellers complete as per detailed dwg.
Side Storage unit: The table to consist of storage unit of size 1500 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
Back Storage unit: The table to consist of storage unit of size 2100 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation,
with levellers complete as per detailed dwg.
Side Storage unit: The table to consist of storage unit of size 1000 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
Back Storage unit: The table to consist of storage unit of size 1800 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
47 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation,
with levellers complete as per detailed dwg.
Side Storage unit: The table to consist of storage unit of size 1000 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate
inside and outside with necessary approved hardware complete as per detail dwg.
6.00 GREEN ROOM TABLE /SECURITY TABLE/ RECORD ROOM 6.00 nos
Dimensions: 1200mm X 600mm X 750mm ht.
Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge
Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation,
with levellers complete as per detailed dwg.
Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Cost also to include
provididng and fixing 75mm dia Grommets 1no for each Table
Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation,
with levellers complete as per detailed dwg.
Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports
and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.
Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Cost also to include
provididng and fixing 75mm dia Grommets 1no for each Table
Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation,
with levellers complete as per detailed dwg.
Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports
and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.
48 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports
and will be accesable to user with a flap .
Cost also to include provididng and Fixing 50mm dia Spine as per Manufacturers specs.
Side Storage unit: The table to consist of storage unit of size 1500mm X 450 mmX 750mm consisting filing cabinet finished with 1 mm laminate inside and
with 4mm Veneer from outside with necessary hardware as approved complete as per detail dwg.
Base: The base of the table shall consist of SS legs as permanufacturers spec with levellers complete as per detailed dwg.
Back Storage unit: The table to consist of storage unit of size 2400mm X 450 mmX 750mm consisting filing cabinet finished with 1 mm laminate inside and
with 4mm Veneer from outside with necessary hardware as approved complete as per detail dwg.
Wire Management : Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical
sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.
Base: The base of the table shall consist of MS Powder Coated legs as permanufacturers spec and matching with the legs provided for the workstation
with levellers complete as per detailed dwg.
Wire Management : Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical
sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.
49 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.
Base: The base of the table shall consist of MS Powder Coated legs as permanufacturers spec and matching with the legs provided for the workstation
with levellers complete as per detailed dwg.
Wire Management : Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical
sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.
Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.
Base: The base of the table shall consist of MS Powder Coated legs as permanufacturers spec and matching with the legs provided for the workstation
with levellers complete as per detailed dwg.
Wire Management : Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical
sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.
Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.
Base: The base of the table shall consist of MS Powder Coated legs as per manufacturers spec and matching with the legs provided for the workstation
with levellers complete as per detailed dwg.
Wire Management : 150 mm x 450mm MS powder coated Cable tray and Cable riser box to be provided below the table top as shown in dwg with
seperation for data and power. The cable tray will house electrical sockets and data ports and will be accesable to user with Rotatable flip top with
approved colour opening to 180 deg. One table to be shared by two.
Providing & placing in position Pedestal unit of 450mm X 450mm X 675mm ht. Pedestals are made from 19mm thk prelaminated Partical Board with
matching colour Edge binding. Drawer unit shall consist of 2nos 19mm thk prelaminated Partical Board with approved colour edge binding of 300mm &
350mm ht. over foolscap filing drawers have full extension ball bearing slides. The drawers shall be provided with 19mm thick prelaminated Partical Board
fascia with matching colour edge binding. Mobile pedestals to have an anti-tilt caster and all pedestals shall have a Individual locking system. All
pedestals and flipper bins have quality locks with removable inner cylinders and are master keyed up to 2000 different combinations.
Add ED @ ______%
Note:
Sizes may change as per site conditions & Architect ’s / Project Manager’s instruction.
The vendor to submit BOM with component cost along with this quote.
The vendor to submit the image & drawing of the workstation along with this quote.
Laminate / fabric / Powder coated Metal surface colour as per samples approved by the Architect / Owner / Project manager.
All junctions of column and workstation clusters shall be as per drawings issued by the Architects office. Where ever required partition shall be turned in
order to facilitate networking / electrical cables to be drawn. This component must be taken into consideration while quoting for the workstation.
50 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
Date : 12-12-2013
BILL OF QUANTITIES FOR CHAIRS
1 Supplying & placing in position medium back chair with following specification. Nos 728.00
Seat rest: Two Pieces of PP Plastic injection seat shells connected by 4 nos of self tapping screws. 50 mm range of adjustment of slideable seat.
Common
Back rest: mounting opening
The medium ready
back rest in with M6
fabric nutframe.
over for all different
The backtype
rest of
to mechanisims,
have provisionarms and backbones.
of height Seatrest with
adjustable backrest polyurithene
for an cout heavy
optimum adjustment of
the lumbar support, to be either by turning knob or push- button. upholstered with mesh
Mechanism: Synchronised moment of back and seat A 2 to 1 ratio and pivot point under the front rdge of seat. Pivotal pressure point of backrest
provides
Gas full support
lift: 100mm in upright
strocke andpneumatic
imported any reclining
gasposture
lift with.130mm
Tilt lock range
in multiple
heightposition and has
adjustment andreclining angle
thrust force of newton.
400 160 the reclining tension of backrest
Arm rest: P.P Plastic injection arm height adjustable ( 60mm range of adjustment) and arm support angle ( 180 Degree) swivelable possibility
Base: MS powder coated base with high tonnage compression available in natural polished finish
2 Supplying & placing in position medium back chair with following specification. Nos 111.00
Seat rest: Two Pieces of PP Plastic injection seat shells connected by 4 nos of self tapping screws. 50 mm range of adjustment of slideable seat.
Common mounting opening ready with M6 nut for all different type of mechanisims, arms and backbones. Seatrest with polyurithene cout heavy
duty foam and upholstered with approved Fabric.
Back rest: The medium back rest in fabric over frame. The back rest to have provision of height adjustable backrest for an optimum adjustment of
the lumbar support, to be either by turning knob or push- button. upholstered with mesh - white colour/ approved colour
Mechanism: Synchronised moment of back and seat A 2 to 1 ratio and pivot point under the front rdge of seat. Pivotal pressure point of backrest
provides
Gas full support
lift: 100mm in upright
strocke andpneumatic
imported any reclining
gasposture
lift with.130mm
Tilt lock range
in multiple
heightposition and has
adjustment andreclining angle
thrust force of newton.
400 160 the reclining tension of backrest
Arm rest: P.P Plastic injection arm height adjustable ( 60mm range of adjustment) and arm support angle ( 180 Degree) swivelable possibility
51 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Mechanism: Synchronised moment of back and seat A 2 to 1 ratio and pivot point under the front rdge of seat. Pivotal pressure point of backrest
provides full support
Gas lift: 100mm in upright
strocke andpneumatic
imported any reclining
gasposture
lift with.130mm
Tilt lock range
in multiple
heightposition and has
adjustment andreclining angle
thrust force of newton.
400 160 the reclining tension of backrest
Head rest: Headrest to have height adjustable to support the neck upright or reclined with polyurithene cout foam and upholstered with mesh
Arm rest: P.P Plastic injection arm height adjustable ( 60mm range of adjustment) and arm support angle ( 180 Degree) swivelable possibility
Base: Chrome finished legs with nylon castors
Castors: Twin wheel high resistant polyamide castors.
Add ED @ ______%
GRAND TOTAL -
52 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
Date : 12-12-2013
Chain Drive Unit: Shall be of a high engineering grade moulded plastic with steel support pin enclosed in a plastic housing,
and inserted into a control tube end. It shall be driven a ball chain pulley attached to a specially designed clutch
mechanism, forming a continuous loop. It can be positioned on the left or right hand side of the shade. The shade when
lowering or raising shall be automatically locked in position upon release of the ball chain by the clutch with its built in friction
lock.
Chain Drive Idler end: Shall be of moulded plastic with a steel location pin enclosed in a plastic housing. The plug shall be
inserted into the tube end.
Chain Drive installation Brackets: The installation brackets shall be Zinc plated steel supplied in pairs. One bracket in each
pairs is used for the control side of the shade (side with the ball chain). The other bracket is used for the rotator or idler end
side.
Ball Chain: Shall be 2mm Diameter PVC cord with 3mm diameter acetal balls moulded co-axially to it on 7.5mm pitch to
form a continuous loop. It is used for raising or lowering the shade.
Bottom rail: shall be round aluminium tube, anodized, with a diameter of 20mm & thickness of .5mm
53 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
Fabric specification:
Fabric description : Combine visual comfort and thermal performance - Screen fabric for internal roller blinds - Two sides, two
functions to combine visual comfort and thermal performance.
GRAND TOTAL -
54 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai
Date : 12-12-2013
SL.NO. DESCRIPTION UNIT Total Qty TYPE OF SIGNAGE SIZE RATE AMOUNT REFERENCE IMAGE
I SIGNAGES
1 Company Name Signage as per design- Reception set 1.00 Mounted 900 x 600mm
Providing and fixing signage 1nos of size 900mm x 600mm letters with
Logo- SS Brush Steel Logo
4 Rest Room ( Gents , Ladies & Handicap) Nos 60.00 Mounted 130x 150mm
Providing and fixeing signage with 3mm thk ACP Sheet SS brush finished
plate with SS Symbol fixed with Birla 3M double sided sticker as per the
approved sample.
5 Push & Pull Signage on Glass Door Nos 75.00 Mounted 100 x 50mm
3mm thk brushed finished logo with viny sticker fixed with screws. as per
approved sample.
55 RC Design Pvt.Ltd
Project : Interiors for NCSCM @ Chennai
Owner : NCSCM
SL.NO. DESCRIPTION UNIT Total Qty TYPE OF SIGNAGE SIZE RATE AMOUNT REFERENCE IMAGE
Note : The Exact Signages of Each type to be cross cheked at site before
production.
56 RC Design Pvt.Ltd
Project: Interior fitout for NCSCM
Client : NCSCM
1.0 FLOORING
The ceramic tile shall be of approved quality, make, color, size and shape. On the
approval of the sample by the PM, the order for the tiles shall be placed from one
source and procurement done preferably from one batch/consignment to prevent
any shape variation. Tiles to be sorted out at site before laying.
The floor surface over which the tiles are to be laid shall be properly cleaned and
wetted. 3 to 6 mm Solid bed of BALCEM GOLDSTAR (POLYMER MODIFIED
CEMENTITIOUS ADHESIVE) & in conjunction with BAL-ADMIX AD1 (POLYMER MODIFIED
LIQUID) shall be applied over an area adequate to accommodate about 20 tiles at a
time. Tiles shall be washed clean and pressed on to the grout and gently tapped in its
proper position. The tiles shall be placed perfectly side by side so as to have fine joints
truly vertical and horizontal and in level with adjoining tiles.
The joints shall be as specified in the drawing, if grooves are to be provided, it shall
not exceed 1.5mm or as specified in the drawing, and shall be done using spacers of
approved quality. The excess content slurry bulging/oozing out in joints shall be
removed by wiping immediately. Joints between the tiles to be filled with BAL GROUT
to match the color of tiles as per the manufacturers’ specifications.
Thereafter, the joints shall be raked out to the required depth and loose
cement/mortal shall be revved and joints shall be cleaned. Joints between the tiles to
be filled with BAL GROUT to match the color of tiles as per the manufacturers
specifications. (color as approved by PM) to match the color of tiles.
In the case of dado the wall surface shall be cleaned and plastered with CM 1:4 to a
thickness of not less than 10 mm to form a uniform backing surface and finished rough
and allowed to harden.
The tiles, which have been soaked in water, shall be cleaned and cement paste of
butter like consistency applied to the backside of tiles and the tiles shall be pressed
on the wall face and gently tapped in its position. In this way tiles shall be placed one
after another starting from the bottom line and lay upwards.
The joints shall be truly vertical and horizontal, where required spacers – glass strips or
ceramic strips – are used to achieve spacing between tiles of width as specified in
the drawing, and the tile surface shall be of infirm level in all directions without any
depressions and dulling which shall be tested by a straight edge as directed by PMC.
Curing and pointing of tiles in Dado shall be carried out as specified for flooring and
as directed by PMC.
The granite shall be of approved color & shall be out of sufficient lot to cover
particular area to avoid lot/shade variation.
58
Project: Interior fitout for NCSCM
Client : NCSCM
Granite slab shall be quarried stones, hard, sound, durable and free from weathering
and decay and defects like cavities, cracks, holes injurious veins, patches of soft
materials and such other defects adversely affecting its strength and its appearance.
The hardness of the Granite slab shall be as per IS. The pre-polished/flamed granite
shall be selected and approved by the PMC. The pre-polished/Flamed Granite
sample approved shall be brought by the Contractor in adequate quality and from
one single batch/source so as to ensure that the grains and shade of entire flooring
laid is homogeneous and consistent. The size and shape of the granite slab shall be
cut as per the Drawings/instructions of PMC, edges being true and square. The
exposed edges of the slab are to be polished at site or in factory. Cutting of Granite
slabs shall be done using machines as approved by the PMC.
The rate should include protection coat of POP over polythene till handing over. The
rates shall be inclusive of machine-polished edges and groove if ordered.
Mortar shall be composed of cement and sand, unless otherwise specified. All mortar
shall be prepared in accordance with IS 2250. The proportions of mortar measured by
volume shall be as specified.
A layer of mortar shall be spread on full width over a suitable length of the lower
course. Each slab shall be properly bedded and set in position by gently taping with
handle or trowel or wooden mallet. The inside faces shall be buttered with mortar
before the next slab is laid and pressed against it. The joints may be either paper cut
or with spacing width.
In case spacing is provided between slabs, the mortar in the joints shall be raked out
and pointed (type of joint as specified by PMC or drawings) with cement slurry mixed
with coloring pigment (the color of the pigment and its proportion to be mixed with
the cement as specified) to match the shade of the granite. The curing shall be for a
minimum period of 7 days after laying and pointing.
The laying of granite in Staircase treads, landing and Risers shall be similar to laying of
granite flooring as above, except that.
The slabs cut shall be from one single piece, joints shall be paper joint, the
edges shall be treated as shown in drawings.
Anti skid grooves shall be provided for every Tread and Landing as per Detail
drawing. the treads and Landing shall be projecting a minimum of 20mm from
the top face of the riser.
The cut is to be polished either in site or at factory.
The edge of the treads shall be fully bull nosed / chamfered & polished to
gloss as per detail dwg.
The pre polished granite shall confirm to the specification or requirement as that of
Granite used in flooring/staircase. The thickness of the Granite used shall be 20mm
thick and it is fixed over a backing coat of cement mortar of 1:4 of 12mm thick with a
cement paste backed on the back of the granite tile.
59
Project: Interior fitout for NCSCM
Client : NCSCM
The height of the skirting shall be 100mm or as specified the top edge of the skirting
shall be treated as shown in the drawing.
The joints of the granite strip used in skirting are to be less in numbers and it shall be
paper cut joint. The paste oozing out is wiped in a cloth and washed with water. The
curing is to be for a minimum period of 7 days.
1.7 SKIRTING
SS skirting over ply: - fabricating and fixing 50 mm high SS skirting clad over 12mm
thick marine ply using epoxy adhesive.
60
Project: Interior fitout for NCSCM
Client : NCSCM
Scope of work includes Materials such as wood, labor for joinery of wooden frame
and shutter, fixing of the frame and shutter, fixing of laminates or veneer, fittings and
fixtures and such other related carpentry works.
2.1.1 MATERIALS.
Wood for Furniture shall be approved, seasoned and I class Steam Beachwood. It
shall be fairly uniform in color and texture. It shall be free from blemishes, hollow
pockets and knots, spinals or twisted grain, warp and any kind of decay or insect
attack, cupcakes, door holes, splits, cracks, pinholes, wormholes etc.
Wood shall be kiln seasoned before being planed to the required sizes, in
accordance with IS 401-1982.
The contractor shall submit test certificate in support of the kiln seasoning including
ASCII treatment for the entire quantity of timber required for the work from the factory
where seasoning has been done.
Commercial Flush Shutters of thickness 19/32/33 mm & 45 mm and of size as specified
in drawings shall be solid core type with block board core and shall conform to IS
2202 1983 – part I (specification for wooden flush door shutters solid core type) IS 1003
part 1 and 2, IS 3097. Flush door shutters shall be free from twist or warp in plane, and
the four edges of the shutter shall be square. Both faces of shutter shall be sand
papered to a smooth and even texture. Tolerance on nominal thickness shall be + 0.8
mm. Thickness of shutter shall be uniform throughout with the variation not exceeding
+ 0.8 mm when measured at any two points.
All commercial shutters shall be internally lipped using approved wood, pressed and
ready from the Factory directly. In the case of double leafed shutters, rebating shall
be as indicated in drawings and directed by the PMC. Where separate lipping is
provided, the depth of lipping at the meeting of styles shall not be less than 35mm.
Shutters shall not be damaged during transportation, storage and fixing. Damaged
shutters shall be rejected and shall be replaced with new shutter as directed by the
PMC whose decisions will be final and binding in this regard. From the time the
shutters are procured to the time they are taken up for fixing in position, the shutters
shall be stored in a proper manner with adequate supports so as to avoid damages
to any part, particularly the edges.
The Flush shutter shall be laminated with plastic laminate sheet or veneer, whose
samples shall be submitted along with manufacturers’ brand name, test certificate
etc to the PMC for approval before placing order. The laminate/veneer sheet is
protected with building paper until ready for use.
61
Project: Interior fitout for NCSCM
Client : NCSCM
The average moisture content of all the WOODEN samples from a lot shall be within +
4% and moisture content of individual samples + 6% of the maximum permissible
moisture content. For this purpose the site of work shall be deemed to fall under
climatic zone II. Seasoned wood as per IS 1141 –1973 and IS 287 – 1973 shall be basis
of acceptance.
2.1.3 WORKMANSHIP
Timber sections for frames shall be planed smoothened to accuracy on all sides to
the full dimension, rebated, rounded, chamfered or moulded as shown in drawings or
as directed by PM without patching or plugging of any kind before they are framed
and jointed. A tolerance of + 2 mm shall be allowed in the finished cross sectional
dimensions.
The joints shall be of mortise and tendon or tongue & groove type simple, neat and
strong. Joints shall fit in fully and accurately without wedging or filling. The joints shall
be glued, framed, put together and pinned with hardwood or pins not less than 10
mm dia, sash bars if any shall have metered joint with styles. Putty where used shall
conform to IS 419-1967 and shall be a homogeneous paste and shall be free of dust,
grit and other visible impurities.
After the frames are put together, they shall be pressed in position by means of a
press. The contact surfaces of tendon and mortise joints shall be treated (before
putting together) with bulk type synthetic resin adhesive of a make approved by the
PM. Rails, which are more than 180 mm in width, shall have 2 tenens. Styles and
shutters shall be made out of a single piece and shall have a 12 mm groove to
receive panels.
Before the frames are fixed in position, these shall be inspected and passed by the
PM. The frame shall be placed in proper position, secured to walls or columns as the
case may be, with bimetallic fasteners, iron hold fasts etc. as shown in drawings and
directed by the PM. In case of doorframes with sills are provided, these sills shall be
embedded/sunk in the floor for full thickness of the floor. The doorframes without sills,
while being placed in position, shall be suitably strutted and wedged in order to
prevent warping during construction. The frame shall be protected for damage
during construction.
Where glazed openings are indicated, the size, thickness and type of glazing shall be
provided as in the drawings and shall be lipped internally with S. Beech wood.
Shutters shall have provision for mortise locks where so indicated on drawings or as
directed by the PM.
Shutters shall be checked after fixing for proper location, alignment and swinging.
After fixing all the fittings the shutters shall be tried again for proper closure, handling
and easy movement etc., and any defects noticed should be immediately rectified
as directed.
62
Project: Interior fitout for NCSCM
Client : NCSCM
assume full contact with the adhesive / Fevicol / SR. A constant and even pressure is
applied for not less than 24 hours to ensure good bonding of the sheet to the board.
The laminate/veneer surface shall be cleaned as recommended by the
manufacturer of all stains/ adhesive marks etc.
All Wooden and Veneered surface shall be water cut melamine finished after it has
been approved and passed by the PM. All portions of timber built into masonry or
abutting a concrete portion of the building or buried in ground shall be coated with
boiling coal tar or other type of approved wood preservative or primer before fixing
them in position.
All fittings and fixtures for the doors, storage and worktops shall be as indicated in the
schedule shown in the drawings. The samples along with manufacturer’s / brand
name, test certificate etc, shall be submitted to the PM for approval before placing
order.
The louvers shall be of wood, glass or any other materials as specified in the drawings.
These shall be fixed in grooves made in the frame or shutter. The Venetian blades shall
slope down towards the outside at an angle of 45° or as shown in drawings. These
shall overlap each other by about half of their widths. Beading shall be fixed all
around the openings for louvers as indicated in the drawings.
2.2 PARTITIONS
63
Project: Interior fitout for NCSCM
Client : NCSCM
64
Project: Interior fitout for NCSCM
Client : NCSCM
voids to be filled with 50 mm thk panels of glass wool/ rock wool. All gypsum board
edges to be protected with aluminum angles. Partition to include Approved skirting
at floor level. All internal frame members to be screw fixed.
2.3 STORAGE:
65
Project: Interior fitout for NCSCM
Client : NCSCM
3.1.0 GLAZING
The glass shall be transparent and free from blisters, stones, scratches and bubbles so
as to give a clear visibility throughout the glass. The sheet glass should not show any
distortion of light when tested according to the method prescribed in Appendix ‘B’ in
IS 1761-1960. The cut size of sheet glass shall be within the following tolerance, on both
length and width of the prescribed cut size.
The thickness of sheet glass when tested according to the method prescribed in
Appendix –C in IS 1761 – 1960, shall be as follows, within the tolerance indicated
against each.
The size for glazing shall allow a clearance of 2.5 mm between the edges of the glass
and the wood or metal surrounds. The clearance may be increased, provided the
depth of the reedit or groove is sufficient to provide not less than 15-mm cover to the
glass. The detailed process of glazing shall be as specified in IS3548 –1966 code of
practice for glazing in building.
All stains form the surface shall be removed and cleaned with thinner. The edge of
glass or glazing sheet when rounded shall render a uniform look throughout the
length and shall be neatly finished.
66
Project: Interior fitout for NCSCM
Client : NCSCM
Unless otherwise shown on the drawing, the fabricating tolerances shall generally be
as follows:
Straightness: compression members shall not deviate from straightness by more than
1/1000 of the axial length between points, which are to be laterally supported.
Completed members shall be free from twist bends and open joints. Sharp links or
bends shall be cause for rejection of materiel.
The stainless steel pipes shall be procured from approved manufacture and of
approved grade. The quality of stainless steel sheet and pipe shall be approved by
PM before proceeding with execution any item of work. The surface finish of the
entire component used in executing the item should be brushed finished
The pipe used for handrail shall be of 14 gauges thick. All joints to be done with
welding only of TIG (tungsten inert Gas). The welded links are to be ground and organ
buffed to get the original finish of the surface of the material welded. The joints or
junctions where two pieces are joined/welded to be precisely cut and then welded,
SS Bal Acrylic emulsion s and 10mm thk toughened glass. The fixing details of the
handrail shall be as specified in the drawing or instructed by PM / Architect.
67
Project: Interior fitout for NCSCM
Client : NCSCM
5.1.0 PAINTING
The surface shall be thoroughly cleaned of suet etc., and be allowed to dry for at
least 48 hours. It shall than be rubbed thoroughly with sand paper to give a smooth
and even surface. Any unevenness shall be made good by applying putty, made of
plaster of Paris mixed with water on the entire surface including filling up the
undulation and then sand paper the same after it is dry.
The cement primer shall preferably be applied by brushing and not by spraying.
Horizontal strokes shall be given first, and vertical strokes shall be applied immediately
afterwards. The entire operation shall constitute one coat. The surface shall be
financed as smooth as possible leaving no brush marks.
Acrylic emulsion paint of approved brand and manufacture shall be used. The primer
where used as on new work shall be oil-based primer. These shall be of the same
manufacture as the plastic emulsion or as approved by PM. Only sufficient quantity of
paint required for days work shall be prepared.
The paint and primer shall be brought be brought by the Contractor in sealed tins in
sufficient quantities and from one single batch/consignment, and the same shall be
kept in the joint custody of the Contractor and the PM. The empty tins shall not be
removed from the site of work till this item of work has been completed and passed
by the PM.
Preparation of the Surface: the scaffolding used for painting should be erected taking
care not to rest on the walls so as to avoid any damage to the wall surface. For new
work the surface shall be thoroughly cleaned of dust, old white or color washes by
washing and scrubbing. The surface shall then be allowed to dry for at least 48 hours.
It shall then be sand papered to give a smooth and even surface. Any unevenness
shall be made good by applying putty, (made of ingredients plaster of Paris, chalk
powder, primer, paint etc., mixed as specified or directed by the PM) on the entire
surface including filling up the undulation and then sand papering the same after it is
dry.
One coat of sealer and two coats of Acrylic emulsion paint are to be applied. The
application is done using good quality approved make brush. On the final
application, roller is used to get a better and acceptable finish (the roller application
is done on smooth wall surface only). At places where required, the application of
paints is done on granular finished surface, in which case no application of putty and
sand papering is required. The work is to be carried out under direct Guinness and
instructions from the manufacturers whose expert advice and supervision are to be
made available in order to achieve the high-grade finish. The painters employed for
this work must be capable of producing the highest standard of workmanship
required. If the finish is of doubtful nature, the contractor shall have to rectify the
entire, at his own cost, to the satisfaction of the PM.
68
Project: Interior fitout for NCSCM
Client : NCSCM
All textured paint to confirm to specific IS. The paints of specific make/manufacture
that are mentioned in the specifications are to be used.
The textured paints may be of exterior / interior grades as specified.
The surface is prepared free of dust/dirt/grease and other foreign matters. The
scaffolding is to be done as for the other type of painting.
Texture finish painting is a wall coating available in different readily available textures
finishes and colors and is a substitute to conventional wall finishes. These paints can
be texture recessed raised, granular smooth etc. dinettes. The glossy can be
achieved by adding marble powder to the required proportion.
As far as possible only ready mixed color/shades is used directly unless until a shade
difference is required, which is achieved using strainers of approved make and color,
mixed in approved proportion.
The thickness of granule used in the textured paint is 2.5mm. This finish can be applied
on any surface of finish like cement plaster, good surface of brick masonry and also
already painted surface. The textured finish acts as better fire retardant coat against
the conventional type of painting. This paint is also anti-fungus and anti-corrosive.
The finish needs a minimum of 3 hours to dry and shall be ready to use after 24 hours.
The application is either done with brush or spray gun or trowel (also manual pressure
on the trowel) or roller depending on the required finish and as per the
manufacturers’ instruction.
The applicator should be skilled and specially trained by the manufacturer of the
particular texture paint to do such work.
The contractor shall purchase synthetic enamel paint of approved quality make color
and shade.
All steel surfaces shall be thoroughly cleaned of all dirt, grease and rust. Any small
areas, which become inaccessible after assembly, shall be painted before assembly.
The surface shall be perfectly dry before painting.
The priming coat for steelwork shall be applied after the surface has been prepared.
After the priming coat has dried all blowholes and dents shall be filled with metal
paste and surface smoothed with sandpaper.
Wherever shop primer painting is damaged, the surface shall be thoroughly cleaned
and touched up with corresponding primer.
Site painting shall not be done in frosty or foggy weather or when humidity is such as
to cause condensation on the surface to be painted.
69
Project: Interior fitout for NCSCM
Client : NCSCM
The contractor shall take care to clean thoroughly all stains of paint on glasses, walls,
fittings, fixtures etc. by applying turpentine on thinner.
The powder coating to be done on steel / aluminum surface shall be epoxy hi bird or
pure polyester. The Finish shall be Matt, glossy /semi-glossy, textured or structure types
which shall be as approved by the PM. The variation in thickness of coating shade of
the color and finishes shall be achieved varying the temperature of heating.
Degreasing
Watering
Picking/chromatin
Water rising
Phosphating
Oven heating and
Cooling at room temperature etc.
The quality / color / shade of the powder used shall be of reputed approved
manufacturer. The contractor shall submit to the PM a sample for approval before
finally placing an order. The thickness of powder coating shall be based on the
surface being coated and the resilience to weathering effects required for the
particular item. The thickness of coating varies from a minimum 20 microns to
maximum to 60 microns. The temperature of oven heating shall be around 185°C. The
specialists/manufacturers’ specification in using the product shall strictly be adhered
to in preference to the specification in the contract.
5.1.6 VAPOCURING
Vapocuring finish shall be done for Metal surfaces exposed to both interior and
exterior atmosphere. The putty material, hardener, base coats material, Polyurethane
coat material and the paints used shall strictly be in accordance with the
manufacturers’ specification.
70
Project: Interior fitout for NCSCM
Client : NCSCM
Melamine finishing shall be done on wooden surfaces. The finish shall be Matt, glossy,
semi glossy type which shall be as approved by the PM.
All uneven and rough surfaces shall be rubbed-using sandpaper of the required
grades till a smooth surface is obtained and the surface shall then be well dusted. The
nail marks/ pores in the wood shall be filled with wood filler and the surface shall be
rubbed with the required grade of sandpaper so that the entire surface is uniformly
smooth.
After preparing the surface as specified above, application of a sealer coat shall be
done.
Wherever necessary the pores in the wood shall be again filled with wood filler and
the surface shall be rubbed with the required grade of sandpaper in the presence of
water so that the entire surface is uniformly smooth. Staining as required shall be
done manually, application of second coat of sealers shall be done. Finally 3 coats of
Melamine spraying, strictly under dust free condition, shall be done, after which the
surface is buffed with Wax & Oil.
71
Project: Interior fitout for NCSCM
Client : NCSCM
False ceiling should be carried out with lightweight boards made of basic materials
like aerated gypsum treated with special additives, and both sides are covered with
a special off white/white color paper. The size, thickness and texture of the board or
tile available is as per the manufacturer details.
The Gypsum boards or tiles should confirm to IS 2542-1981 and IS 2095-21982 physical
properties of Gypsum board should confirm to:
Density: nominal in a dry state = 807.10 kg/m
Fire resistance: 12.5mm = ½ hour resistance. Material classified as class
1 surface soared of flame test as per BC476 PART –7
1971
Sound insulation: The average rate of noise reduction between
frequencies of 100 Hz is 35.6 dB for a partition 75 mm or
97 mm thickness with a 12.5mm board on each face
38.5. DB for a partition as above but including 265 mm
of mineral wool in the cavity
42.5 BD for a 100mm partition comprising of two layers
of 12.5-mm board on each side.
Gypsum board should be flexible enough to resist any crack due to limited
movement of a building.
False ceiling should present unbroken surface and desirable continuity may be varied
by treatment of joints with wood or plastic or PVC or metal or any other such material
strips.
Off loading of gypsum is only advisable on small boards and may be carried by one
man but generally two men will be required and this will reduce the risk of damage to
the boards. Boards are manually carried on edge.
When storing boards, care should be taken to keep in a dried and covered place
sheltered from rain and avoid dampness from floors. They should be supported on
wooden battens, which should not be more than 45 cm apart on a flat surface.
72
Project: Interior fitout for NCSCM
Client : NCSCM
prior to cutting or with practice. The rule may be drawn down the board at the
required distance from the edge whilst the board is scored with a knife at the edge of
the rule. The board should then be pressed with both hands and gypsum score will
break in the line with the cut in the side face. The board should then be turned over
and the side paper be cut with the knife.
Gypboard may be cut using a normal saw. A fret saw or an electric tool may also be
used for the cutting of curves. When large quantities of board are to be cut, the use
of a circular handsaw is advisable.
Electrical or manual carpenter’s tools as those employed in the cutting of wood may
be used for making cutouts in gypsum board. A drill should be used when making
holes for electrical installation thermostat boxes, etc. For holes of diameter less than
50mm high speed steel drill should be used.
The edge of the board can be pared off using planes. A file may also be used to level
off any irregularities, which may remain after cutting. The edge of both papers, faces
may be trimmed by using fine sand paper
Gypboard may also be used to line curved areas. The curvature radius shall be 60cm
for 9.5mm board and 100cms for 12.5-mm board. 30 to 60 minutes before application
to curved areas, both sides of the gyp board should be sprayed with water until they
are damp. The board should then be bent very slowly and carefully, and fixed in to
position. Before joining the boards should be completely dry
The ceiling is suspended using systems made of G.l. The suspended ceiling may be
heavy duty (load bearing ceiling on which a person can walk over a ladder for
maintenance purpose) or light duty (non loading bearing). Both these systems may
be either with a layer of vinyl film laminated.
On completion of the erection of the grid work, care should be taken to see to it that
the bottom face of the grid work is on true water level or to the required gradient or
profile
Where light fittings, access panels and similar components are incorporated as a part
of the design requirement, consideration must be given to maintaining the integrity of
the ceiling. The fire and sound insulation are also important factors.
Immediately after the tape has been fixed, a new layer of material is applied over it,
flush with the surface of the board. Before the material begins to stiffen the jointing
sponge should be moistened and surplus material wiped from the edge of the joint
without disturbing the main joint filling. The sponge should be rinsed occasionally to
73
Project: Interior fitout for NCSCM
Client : NCSCM
prevent material setting in it. Once the material is dried any slight depression in the
surface can be filled again and projection cut back
When the material has dried about 1 hour after application, a thin layer of jointing
compound is applied in a broad brand 200mm wide. The edges of this band should
be immediately feathered with a slight damp joining sponge. When the joint material
has completely dried another application is made 250mm wide and feathered out as
before. It is important that the first coat of finish is allowed to dry before the final coat
is applied
CUT EDGES: A finish similar to that achieved with the tapered edge
board can be obtained with cut edge boards or acute edges
and tapered edge board. The cut edge should slightly sanded
to remove any burrs
The edge of the adjoining boards is cut to make v-groove with
a sharp knife. The joints are flush with the face of the board,
using gyp board jointing compound. The gap must be filled
solidly back to the framework. The coat is applied and joint
tape bedded in it as tightly as possible, leaving sufficient
material behind the tape to ensure good adhesion and to
eliminate air bubble. Gyp board jointing compound is then
applied with a sponge. When this has dried a second
application of 200mm wide is applied and the edges are
feathered out. Wider feathered out of the joint will overcome
slight misalignment of cut ends and edge joints.
SURFACE TREATMENT:
When the jointing is dry, one coat of gyp board dry wall
topcoat is applied to the entire surface using the medium pile
roller, and brush or entirely by brush.
All the accessories like the ceiling section, perimeter channels, intermediate channels,
clips, cleats jointing compound jointing tape screws nails etc used in erecting the
false ceiling should be recommended by the manufacturer and under the instruction
or guidance of the manufacturer
The type of board –size, texture, edge finish or the type tiles used should be strictly as
per the approved selection of the PM / Architect.
74
Project: Interior fitout for NCSCM
Client : NCSCM
This lining is done either on to masonry insulation natural or any other material using
specified thickness Gypsum board manufactured by approved agency. Specified GI
section of appropriate gauge is screwed on to the surface to be lined with gypsum
board and subsequently board is dry screwed on to the sections. The joining of
boards, treating of joints and surface finishing is similar to that the false ceiling.
75
Project: Interior fitout for NCSCM
Client : NCSCM
1. Table top : Standard table top height – 750mm (including table top thickness of 25mm)
2. Work surface shall be 1500 mm long x 600 mm deep made up of 25mm thick laminated plain
particle board with post formed edges.
3. Table top to have powder coated Flip top to access the Electrical & Network Sockets.
4. The edges of work surface shall be provided with post formed edges.
5. Non‐working edges of the work surface shall be provided with machine pressed 0.5mm thick
PVC lipping / edge binding.
6. Cable tray and Cable riser box made up of MS sheet powder coated to be provided below
the table top with separation for data and power. The cable tray will house electrical
sockets and data ports and will be accessible to user with Rotatable flip top with approved
colour opening to 180 deg.
7. The panel in front of table top shall be of 8mm the Laminated Glass .The panel to have MS
Powder coated bottom frame. The side panel shall be Detachable / sliding panel made of
12mm thick Magnetic soft board wrapped with approved fabric with MS Powder coated
frame.
8. Storage: size 1350 mm x 450mm x 450mm made of 19mm thk prelaminated particle Board.
This will include under structure support made of MS Powder coated tubular section of the
workstation.
9. The Top of the Storage to be provided with 50mm thk foam wrapped with approved Fabric
for seating purpose
10. CPU Holder : Fixed below the table top of size 180 x 420 x 370mm made of MS powder
coated sheet with side perforation panel for ventilation complete with all necessary
hardware.
7.2 CUBICLE
76
Project: Interior fitout for NCSCM
Client : NCSCM
1. Table top : Standard table top height – 750mm (including table top thickness of 25mm)
2. Table top to be made of 25mm thk approved pre‐laminated particle board. The table top to
have a Post Formed Edge.
3. Table top to have 75mm dia Grommet 1no to access the Electrical & Network cables.
4. The edges of work surface shall be provided with post formed edges.
5. Non‐working edges of the work surface shall be provided with machine pressed 0.5mm thick
PVC lipping / edge binding.
6. Base : The base of the table shall consist of MS Powder coated legs with panel below the
table top which is powder coated matching to the legs
7. Storage: The cubicle to have a side storage and a front storage.
8. Side Storage of size: 3200 mm x 450 mm x 1200mm consisting filing cabinet.
9. Front storage of size: 1370mm x 450mm x 1200mm consisting filing cabinet.
10. The storages are made of 19mm tk prelaminated board which is finished by 1mm tk
laminate from inside and outside with necessary hardware . All the edges to be provided
with machine pressed 0.5mm thick PVC lipping / edge binding.
1. Table top : Standard table top height – 750mm (including table top thickness of 25mm)
2. Table tops to be made of 25mm thk approved pre‐laminated particle board. The table top to
have a Post Formed Edge.
3. The table top shall be factory‐made, pre laminated board with laminate of 1mm thickness
4. Table top to 75mm dia Grommets 1no to access the cables.
5. The edges of work surface shall be provided with post formed edges.
6. Non‐working edges of the work surface shall be provided with machine pressed 0.5mm thick
PVC lipping / edge binding.
7. Base : The base of the table shall consist of MS Powder coated legs with panel below the
table top which is powder coated matching to the legs
8. Storage: The cubicle to have side storage and a back storage.
9. Side Storage of size: 1000 mm X 450 mm X 750mm consisting filing cabinet.
10. Front storage of size: 1800 mm X 450 mm X 750mm consisting filing cabinet.
11. The storages are made of 19mm tk prelaminated board which is finished by 1mm tk
laminate from inside and outside with necessary hardware . All the edges to be provided
with machine pressed 0.5mm thick PVC lipping / edge binding
1. Table top : Standard table top height – 750mm (including table top thickness of 25mm)
2. Table tops to be made of 25mm thk approved pre‐laminated particle board. The table top to
have a Post Formed Edge.
3. The top shall be factory‐made, laminated with laminate of 1mm thickness
4. Bottom shall have a backing laminate of minimum 0.6mm thickness.
5. Base: The base of the table shall consist of MS Powder Coated legs.
6. Cable management: Cable tray in MS powder coated finish to be provided below the table
top .The cable tray will house electrical sockets and data ports and will be accessible to user
with a flap .The table also to have MS powder coated vertical for electrical and networking
cable entry.
77
Project: Interior fitout for NCSCM
Client : NCSCM
1. Table top : Standard table top height – 750mm (including table top thickness of 25mm)
2. Table tops to be made of 25mm thk approved particle board finished in Veneer polished in
melamine . The table top to have a Post Formed Edge.
3. Base: The base of the table shall consist of SS legs as per manufacturer’s specs.’
4. Side storage : size 1500mm X 450 mm X 750mm consisting filing cabinet finished with 1 mm
laminate inside and with 4mm Veneer from outside with necessary hardware
7.6 PEDESTAL
1. Pedestal unit of size: 450mm X 450mm X 675mm ht.
2. Pedestals are made from 19mm thk prelaminated Particle Board with matching colour Edge
binding.
3. Drawer unit shall consist of 2nos 19mm thk prelaminated particle Board with approved
colour edge binding of 300mm & 350mm ht. over foolscap filing drawers have full extension
ball bearing slides.
4. The drawers shall be provided with 19mm thick prelaminated particle board fascia with
matching colour edge binding.
5. Mobile pedestals to have an anti‐tilt castor and all pedestals shall have an individual locking
system.
6. All pedestals and flipper bins have quality locks with removable inner cylinders and are
master keyed up to 2000 different combinations.
78
Project: Interior fitout for NCSCM
Client : NCSCM
(a) Powder coating shall be with Epoxy powder of a standard shade or as required.
(b) The specific gravity of powder should be such that it gives DFT (Dry Film Thickness) of 50 –
60 micron.
(c) It should withstand salt spray test of not less than 1000 hrs as per ASTM‐ B‐ 117.
(d) SCRATCH HARDNESS TEST as per DIN 53153 shall be conducted and results should be
such that no scratch shall show bare metal with a load of 3 kgs.
(e) The following seven step phosphating process treatment shall be conducted before powder
coating.
(i) Hot water rinse
(ii) Knock of Degreasing
(iii) De‐rusting
(iv) Cold water rinse
(v) Activation
(vi) Phosphating
(vii) Passivation.
79