"The Modal 1256 Spoalght ie shippad We wo Carina! —
{4205104 Base Ki
(ed aid Yowe / Poke Assembly
[ilssemble the bese kil using the assembly inclructone Included in
‘he earten.
2. Unpack the Yoke / Poie assembly and place the !ower pole assem-
‘iy info the center hub ofthe base and securely fighten the wing knob,
8.Plaos the yoke assamb'y with pan colar inalalled into the lower pole
ly Adjust yoke to desired height and tighten gold Feight lover on
Goll seovrely.Adjust pan tension with knob on lower pole,
4. Sight loosen tie yoke bolt ard sit knob located on either side of te
Sspatight ane assura inatall wacnors ave spaced avay trom the sgotlgh
Body. Garefily algh_the bolt relches and lower igit nto place. ighten
Litktob to achieve desired ul ction
Eire
(Cautlon) Spotight ust be disconnected from power durrg instalation.
The Midget Mode! 1206 ts desaned o be used with an Fel 1000 wat
lap. Open the ton eoer ot ne lamprouse by tumng the to fastene!
1 tum counter clockwss. Insert the lamp ints the lamp socket assuring
that te lame is fuly seated,
240V Modots se and FEP 1000 watt 20 lamp
is modal not UL ape)
The lamp alignment is adjusted al the factory. However, due to
famap lolarances, it may be racossary 10 realign the lamp ‘eld to
achieve tho asiied eilect. This s dane by loossting the two tex bit
Ton head sevews on either side of te lamps house (Ar a/92 hex key Ie
Fequited) and sliding the lamp bracket to tain the desired field ane
then tightening the four scrows, [athe event the lamp “Hat Spo" fs 19
high of t00 low, the socket may be aujusted by loosening the two Tes
juts on the front af the lamp bracket with a 8/16" wranch, adjusting
tho sockol a roqurod, and ro-ightening the hex ruts,
(Caution) Do nt atemet to adjust not spet wile lamp is it. Note
postion 0! hot scot. isconnest spotight from powerline and make
laustment. Clcse top door afd racheek aignimont
* Five color go's are provided. Remove the calor bocmarang by unscrew
ing the twa plastic Knobs and ifting he onlira assembly up and out
Reimoval is Gasier wien the arris are sighly raised as the assembly Is
lited out, Pace the gels in the color Fames (darkest colors away Irn
‘ka lemp} bj suitaning tha go! betwacs the lwo hinge gn tno arminoet
thebyass fasteners info he holes in the sings, through the, gel material
and foid them over sccuraly Dy spreading tre feel of the fastener. An
SHomate matted of eecuring gelo ata une wir tie wap natal
heboomerang assanbly into he spotight, assuring tha! the baltomm
edge ofthe Boomerang ‘ests inthe siot of the red side extrusion, and
fighton tho we rotainng labs
{Ris recomended that te iampbe turned onal the beginrng of he per
formance ard not urnod aff and turned al and on unenosaay unt the
sparing dd a orale ie a
‘The ight beam ig shapedby an ris and chopping shutter. These controls
are icemed on ine sap 9 the opotigh'A dean slots alsa proved
atin projection. Use Lycian Vo
«Wher operating tie cok
jl 1304 Gobo haar. 5
fhoamarang one oF more color ames may be
of another color ame wil release af
ight ofthe color arms wl release al
frames. Actating
frames, aso
‘Ander is lecated inthe color boomerang to gradually dim the beam,
This controlis the arm futhastp the tont of the spotlight and snauld be
the only contra usad for extended perads of blackout
«= ASpread lens is alse 1Ocdied in He Gola bogrierang, stualed next to th
tater This erovides-a wide ange spread of ightin ane direction {..
fall stage wilh flood). The postion of he
Dy roation of the sprca
Various tghining anges
road angle can be asjusted
hs inte odng abs fo rome Hoody rom
necessary
< Mode! 1208 /-b, this model inesrporates an adjustable dmmer conto
=lacalea-orrlie rae pail to vary the ight tenet. In the Tull GOW pos:
tion the lame is fuly off homever the fans are stl operational wala the
On Ih swith 1 OF
Eee)
(Caution) Disconnect light tom electrical power prior to atemptng an
Gianna fo orovent tected shook hazarae = P""9 “°Y
+ Cleaning: Periodic clearing ofthe spatightis required for peak oper-
ton perfomance, The lenses may 2e eleaned with aleohol or fens
Cleaner solution. Access to the micdie moving lens assembly is
Sccomplishad by iemoval of the colar boomerangassenbiy. Homeval
Of this fens should not be neosesary for cleaning, however may be
accomplished by unscrewing the two philips head
ing the batts to the front fan and reroval fhe Cae,
{cus adjusiment knob unt i remeved, moving te foovs lens arm
inward 19 approximately a 45 degree angle and then siding the iene
assembly forward unt clear ol the supparing guide rods. The lens
Assembly may non be angiedout through the color boomerang sid
instalation is in reverse order. Nate that the nan-operation sido cl
the fens alder has a nich en whieh the guide rod must re
belwoen, Faiure‘o instal the ions propery wil cause the spotight to
No focus properly Assira tha! the'talfiaxs racnstaliog. thie Balle
feduces felected light trom beng emiled trom theunt.
+ The spotlight may be cleaned with a soap and water solution and
wiped ary
Replacement of parts - The Model 1206 is easly serviced an most
paris are fied replaceable, To essure continued Oi. compat ity and
Edte oparaton only orginal rplacemen eloctical parte Should weed.
‘Schematle-Siown below in Fig. 1 is the witing dkagiam forthe spot ght
i> ald n locaing election! provioms. Heter tothe table below te atin
roublechootng,
Problem Probable Cause
1) Lamp willaot ight (switch tt) 1.) Lamp deteciv
‘ofoctive cooker detective
loose wre; mp improperly
seated.
2.) Fan(s) inoperative (lamp Il) 2.) Verity no ebstructions. Fan
plua( loose ans) deestve
Fic. +
Rennes