Professional Documents
Culture Documents
Fire Retardant
Low Smoke and Halogen Free
Fire Resistant
Application
This cable is mainly used for interconnecting cable for jumpers, patch cords or pigtails.
Description
Simplex
Simplex cable consists of single tight buffered fiber with aramid yarns as tensile strength members with
jacket of either Flame Retardant PVC or LSZH compound. The cable is unconnectorized.
Duplex Flat
Duplex Flat Cable consists of two simplex units. Two simplex cords are placed side by side and jacketed
with either Flame Retardant PVC or LSZH compound. The cable is unconnectorized.
Construction
#
!
01
Ʒ
TIGHT BUFFER PVC/LSZH JACKETED SIMPLEX / DUPLEX CORD
Ʒ
Ʒ
Physical Properties
Nominal Maximum Pulling Load
Nominal Nominal Nominal Outer
Fiber Cable Outer
Weight Weight Diameter Installation In Service
Count Type Diameter
(kg/km) (lb/kft) (in) (N/lb) (N/lb)
(mm)
Simplex
1 8.2 5.50 3.0 0.118 490/110 290/65
3.0 mm
02
Ʒ
Ʒ
Ʒ TIGHT BUFFER PVC/LSZH JACKETED SIMPLEX / DUPLEX CORD
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:2000N
Under installation: 20hOD Repeated Impact: 2.9 N.m (J) 3h2 impacts
During operation: 10hOD Twist (Torsion): 180h10 times, 125hOD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.;
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧) Crush Resistance: 875N/cm (500lb/in)
Ʒ
Ʒ
Safety Compliance
General Purpose Grade Flammability Test: OFN (UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6 (UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
GR409-CORE TIA/EIA 568B.3 ICEA-S-83-596
Features
• Suitable for indoor use, such as routing connections in patching systems
• Short "patch cord" cables ideal for links between electronic equipment and fiber panels
• Compatible with wide variety of fiber optic connectors
• High quality tight-buffer coating on fiber for environmental and mechanical protection
• Customized jacket colors available for matching connectors.
• Private labeling on the cable outer jacket is also available.
03
Ʒ
TIGHT BUFFER DISTRIBUTION PVC/LSZH JACKETED CABLE
Ʒ
Ʒ
Application
This cable is used for interconnection of the distribution boxes and end devices. The cable is very
suitable for various indoor and outdoor applications, including routing between buildings within ducts
and inside building up to riser shafts.
Description
The Distribution Cable consists of color-coded PVC tight buffered fibers. The fibers are reinforced with
aramid yarn for superior strength and contains no metallic elements. The fibers are jacketed with Flame
Retardant PVC or LSZH compound.
Fiber Optic Cables
&%#&
Ʒ "(
Ʒ
Physical Properties
Nominal Nominal Nominal Outer Nominal Outer Maximum Pulling Load
Fiber
Weight Weight Diameter Diameter Installation In Service
Count
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
2-6 26.0 17.45 5.0 0.197 1000/225 290/65
8-12 50.0 33.56 7.5 0.296 1425/320 500/112
14-24 140.0 93.96 13.0 0.512 2670/600 890/200
26-36 200.0 134.23 16.5 0.650 4448/1000 1490/335
38-48 300.0 201.34 18.0 0.709 4448/1000 1490/335
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load: 2000N
Under installation: 20hOD Repeated Impact: 2.9 N.m (J) 3h2 impacts
During operation: 10hOD Twist (Torsion): 180h10 times, 125hOD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.;
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧) Crush Resistance: 1485N/cm (850lb/in)
04
Ʒ
Ʒ
Ʒ TIGHT BUFFER DISTRIBUTION PVC/LSZH JACKETED CABLE
Fiber Compliance
Temperature Cycling IEC60794-1-2-F2
Tensile Strength IEC60794-1-2-E1A
Crush IEC60794-1-2-E3
Impact IEC60794-1-2-E4
Repeated Bending IEC60794-1-2-E6
Torsion IEC60794-1-2-E7
Kink IEC60794-1-2-E10
Cable Bend IEC60794-1-2-E11
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
Ʒ
Ʒ
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
GR409-CORE TIA/EIA 568B.3 ICEA-S-83-596
Features
• Used in LAN and distribution applications where compact size and lightweight are required
• Suitable for both indoor and outdoor use - no need for splicing at the building entrance
• Flame-retardant or LSZH version for indoor installations
• Fungus-resistant, water-resistant, and UV-resistant for outdoor installations
• Cable can be armoured for additional protection in direct burial and aerial installations
• Highest specific strength-to-weight ratio for limited conduit space
• Economical for longer distance runs where cable cost is significant
• High quality tight-buffered coating on fiber for environmental and mechanical protection
05
Ʒ
TIGHT BUFFER DISTRIBUTION PVC/LSZH JACKETED CABLE
Ʒ
Ʒ
Application
Breakout Cable is designed for routing to different locations and direct termination of fibers in the field.
The cable is mostly suitable for pre-terminated cable assemblies.
Description
The cable contains 2 to 36 fibers which are individually buffered tight or semi-tight construction. Each
fiber is individually protected in a mini cable. Aramid yarn will be applied either inside the mini cable
or within the inner jacket of the cable. The color coded mini cable may be stranded around a central
strength member which can be either FRP or flexible all-dielectric. Outer Jacket may be PVC or LSZH.
Fiber Optic Cables
Construction
#
&% #&
$ %
Physical Properties
Nominal Maximum Pulling Load
Nominal Nominal Nominal Outer
Fiber Outer
Weight Weight Diameter Installation In Service
Count Diameter
(kg/km) (lb/kft) (in) (N/lb) (N/lb)
(mm)
2 50.0 33.56 5.5 0.217 1200/270 490/110
6 110.0 73.83 12.5 0.493 2000/450 800/180
12 160.0 107.38 13.0 0.512 3515/790 1200/270
24 230.0 154.36 15.5 0.611 5470/1230 2000/450
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:3000N for unarmoured
Under installation: 20×OD 5000N for armoured
During operation: 10×OD for unarmoured cables Repeated Impact: 2.9 N.m (J) 3h2 impacts
20×OD for armoured cables Twist (Torsion): 180h10 times, 125hOD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧) Crush Resistance: 1750N/cm (1000lb/in)
06
Ʒ
Ʒ
Ʒ TIGHT BUFFER DISTRIBUTION PVC/LSZH JACKETED CABLE
Fiber Compliance
Temperature Cycling IEC60794-1-2-F2
Tensile Strength IEC60794-1-2-E1A
Crush IEC60794-1-2-E3
Impact IEC60794-1-2-E4
Repeated Bending IEC60794-1-2-E6
Torsion IEC60794-1-2-E7
Kink IEC60794-1-2-E10
Cable Bend IEC60794-1-2-E11
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1 Ʒ
Ʒ
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
GR-409-CORE TIA/EIA 568B.3 ICEA-S-83-596
Features
• Most rugged and "user friendly" cable design for Local Area Networks
• For installations where ease of termination and termination costs are important factors
• Short and moderate distance links between buildings or within a building, where multiple
termination points are needed
• Breakout cables are designed for direct termination with standard connectors
• Cable ideal for direct pulling with wire mesh grips
• Suitable for both indoor and outdoor use -- no need to for splicing at the building entrance
• Flame-retardant or LSZH version for indoor installations
• Fungus-resistant, water-resistant, and UV-resistant for outdoor use
• High quality tight-buffered coating on each fiber for environmental and mechanical protection
07
Ʒ
CENTRAL LOOSE TUBE CABLE
Ʒ
Ʒ
Application
This cable is characterized by light weight and small diameter, suitable for both aerial and duct
installation. The cable can also be used for direct burial for armoured option.
Description
Central loose tube cable contains one tube with 2 - 24 fibers, which is filled with water blocking gel.
Either aramid yarn or fiber glass is wound around the tube to provide physical protection and tensile
strength. The cable can be jacketed with either PE or LSZH. PE is the preferred option in outdoor
environment for water protection purpose. For direct burial, either steel wire armour or corrugated
Fiber Optic Cables
steel tape armour is applied with an optional inner jacket of either PVC, PE or LSZH. An Aluminium
moisture tape can be incorporated under the jacket for water blocking and shielding purpose. A ripcord is
located under the jacket to facilitate jacket removal.
Construction
Ʒ
Ʒ
%
%%,%%!'* %(()+
(' % *
%($'"
&! ' % )) '
(' %( !
(' %%+&'+&()*+
+* $*
Unarmoured Type
Physical Properties
08
Ʒ
Ʒ
Ʒ CENTRAL LOOSE TUBE CABLE
Construction
%
(' % *
%($'"
(' %'' $*
( + " *!*% & (+
+
* $*
(' %,%(' $*(%, & ! & (+
Physical Properties
Maximum Pulling/Tensile Load
Nominal Nominal Nominal Outer Nominal Outer
Fiber
Weight Weight Diameter Diameter Installation In Service
Count
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
Construction
!&
&&-&&"))*,
)(!&!+ &)%(#!
)(!&(( !%+
+&
'),
)(!&) "
,+ !%+
)(!&-&)(!%+)&-!'"
'),
Steel Wire Armoured Type
Physical Properties
09
Ʒ
CENTRAL LOOSE TUBE CABLE
Ʒ
Ʒ
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:3000N
Under installation: 20×OD Repeated Impact: 4.4 N.m (J)
During operation: 10×OD for unarmoured cables; Twist (Torsion): 180×10 times, 125×OD
20×OD for armoured cables. Cyclic Flexing: 25 cycles for armoured cables;
Temperature Range: 100 cycles for unarmoured cables.
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) Crush Resistance: 263N/cm (150lb/in)
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧)
Fiber Compliance
Fiber Optic Cables
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640
Features
• Loose Tube construction provides environmental protection
• Loose tube jelly filled for superior fiber protection
• Colored coded fibers and binders for quick and easy identification during installation.
• Very lightweight and flexible design allows for easy installation
• UV or moisture resistant for outdoor application
• Compact design with small cable diameter
• All Dielectric strength member
• Anti-termite and rodent protection as options
• Optional Aluminium moisture barrier for EMI protection
10
Ʒ
Ʒ
Ʒ MULTI LOOSE TUBE CABLE
Application
The multi loose tube non metallic cable is designed for outside plant, which is prone to electrical
interference.
Description
The cable consists of 5 to 36 fibers containing tubes or fillers stranded in up to 3 layers around a central
strength member and bound under a PE jacket. Each tube contains 4 -12 fibers. Solid or stranded steel
wire coated with polyethylene is usually used as central strength member. Fiber glass reinforced plastics
(FRP) will be used as central strength member if non metallic construction is required. Either aramid yarn
or fiber glass is wound around the tube to provide physical protection and tensile strength. The cable can
Construction
!&
Ʒ
Ʒ
&&-&&"))*,
)(!& !+ &)%(#!
)(!&
&,'(,'!
)(!&) "
&&
,+ !%+
Unarmoured Type
Physical Properties
Nominal Nominal Nominal Outer Nominal Outer Maximum Pulling/Tensile Load
Fiber
Weight Weight Diameter Diameter Installation In Service
Count
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
2-36 110.0 73.83 12.0 0.472 2670/600 800/180
38-72 120.0 80.54 12.6 0.496 2670/600 800/180
74-84 135.0 90.60 13.5 0.531 2670/600 800/180
76-96 150.0 100.67 14.0 0.551 2670/600 800/180
98-108 170.0 114.09 15.0 0.590 2670/600 800/180
110-120 190.0 127.52 15.5 0.610 2670/600 800/180
122-132 210.0 140.94 16.5 0.649 2670/600 800/180
134-144 230.0 154.36 17.5 0.688 2670/600 800/180
146-216 250.0 167.79 18.0 0.708 2670/600 800/180
218-264 300.0 201.34 19.5 0.767 2670/600 800/180
266-312 350.0 234.90 21.0 0.826 2670/600 800/180
314-360 400.0 268.46 22.5 0.885 2670/600 800/180
11
Ʒ
MULTI LOOSE TUBE CABLE
Ʒ
Ʒ
Construction
!&
&&-&&"))*,
)(!&!+ &)%(#!
)(!&
&,'(,'!
)(!&(( !%+
&+ +& (+ !&+ (#+$'
&&
)(!&) "
Fiber Optic Cables
+&!
'),
,+ !%+
)(!&-&)(!%+ )&-!'"
'),
Ʒ
Ʒ Physical Properties
Maximum Pulling/Tensile Load
Fiber Nominal Nominal Nominal Outer Nominal Outer
Count Weight Weight Diameter Diameter Installation In Service
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
12
Ʒ
Ʒ
Ʒ MULTI LOOSE TUBE CABLE
Construction
!'"
& #%
%$"
$
Ʒ
Physical Properties Ʒ
Maximum Pulling/Tensile Load
Fiber Nominal Nominal Nominal Outer Nominal Outer
Count Weight Weight Diameter Diameter Installation In Service
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
13
Ʒ
MULTI LOOSE TUBE CABLE
Ʒ
Ʒ
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:4000N for unarmoured cables;
Under installation: 20hOD 6000N for armoured cables
During operation: 10hOD for unarmoured cables; Repeated Impact: 4.4 N.m (J)
20hOD for armoured cables. Twist (Torsion): 180h10 times, 125hOD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.;
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧) Crush Resistance: 220N/cm(125lb/in)
Fiber Compliance
Fiber Optic Cables
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640
Features
• Loose Tube construction provides environmental protection
• Loose tube jelly filled for superior fiber protection
• Colored coded fibers and binders for quick and easy identification during installation.
• UV resistant for outdoor application
• Dry water blocking core design for ease of handling
• Anti-termite and rodent protection as options
• Optional Aluminium moisture barrier for EMI protection and water protection
14
Ʒ
Ʒ
Ʒ CENTRAL LOOSE TUBE UNDER WATER CABLE
Application
This cable exhibits excellent tensile strength and side press retardancy, having excellent mechanical and
environmental performance. Featured by its thin diameter and light weight, it is best suited for underwater
condition, junction communication system and long haul communication system.
Description
Central loose tube cable contains one tube with 2 - 24 fibers, which is filled with water blocking gel.
A water swelling tape is helically wrapped around the cable core. Either aramid yarn or fiber glass is
wound around the tube to provide physical protection and tensile strength. The cable is jacketed with PE
Construction
Ʒ
Ʒ
!'"
& #%
$"" %"
!' "
$
!' $" !
!' ! "
""%$$!" %"
%$"
$
Physical Properties
15
Ʒ
CENTRAL LOOSE TUBE UNDER WATER CABLE
Ʒ
Ʒ
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:3000N
Under installation: 20hOD Repeated Impact: 4.4 N.m (J)
During operation: 10hOD for unarmoured cables; Twist (Torsion): 180h10 times, 125hOD
20hOD for armoured cables. Cyclic Flexing: 25 cycles for armoured cables.;
Temperature Range: 100cycles for unarmoured cables.
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) Crush Resistance: 263N/cm(150lb/in)
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧)
Fiber Compliance
Fiber Optic Cables
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640
Features
• Loose tube jelly filled for superior fiber protection
• Colored coded fibers and binders for quick and easy identification during installation.
• High tensile strength design
• Superior mechanical and environmental performance
• Rugged and lightweight design
• Durable construction to withstand high water pressure
• Sufficient waterproof to withstand water penetration
16
Ʒ
Ʒ
Ʒ MULTI LOOSE TUBE UNDER WATER CABLE
Application
This cable exhibits excellent tensile strength and side press retardancy, having excellent mechanical
and environmental performance. Featured by its thin diameter and light weight, it is best suited for
underwater condition, junction communication system and long haul communication system.
Description
The cable consists of 5 to 36 fibers containing tubes or fillers stranded in up to 3 layers around a central
strength member and bound under a PE jacket. Each tube contains 4 -12 fibers. Solid or stranded steel
wire coated with polyethylene is usually used as central strength member. Fiber glass reinforced plastics
Ʒ
Ʒ
Construction
!'"
& #%
&
!' %%!
!' "
$
$"$"$"$"$"
"
!' $" !
""%$$!
"
$
$"" %"
!' ! "
%$"
$
Physical Properties
Maximum Pulling/Tensile Load
Fiber Nominal Nominal Nominal Outer Nominal Outer
Count Weight Weight Diameter Diameter Installation In Service
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
17
Ʒ
MULTI LOOSE TUBE UNDER WATER CABLE
Ʒ
Ʒ
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:4000N for unarmoured cables;
Under installation: 20×OD 6000N for armoured cables
During operation: 0×OD for unarmoured cables; Repeated Impact: 4.4 N.m (J)
20×OD for armoured cables. Twist (Torsion): 180×10 times, 125×OD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.;
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧) Crush Resistance: 220N/cm(125lb/in)
Fiber Optic Cables
Fiber Compliance
Temperature Cycling IEC60794-1-2-F2 Repeated Bending IEC60794-1-2-E6
Tensile Strength IEC60794-1-2-E1A Torsion IEC60794-1-2-E7
Crush IEC60794-1-2-E3 Kink IEC60794-1-2-E10
Impact IEC60794-1-2-E4 Cable Bend IEC60794-1-2-E11
Cool Bend IEC60794-1-2-E11
Ʒ
Ʒ Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640
Features
• Loose tube jelly filled for superior fiber protection
• Colored coded fibers and binders for quick and easy identification during installation.
• High tensile strength design
• Superior mechanical and environmental performance
• Rugged and lightweight design
• Durable construction to withstand high water pressure
• Sufficient waterproof to withstand water penetration
18
Ʒ
Ʒ
Ʒ FIG8 SELF-SUPPORTING CABLE
Application
This cable is ideal for in long distance and interoffice communication in strong current zone, as well as
power transmission system. The built in suspension stranded rope provides high tensile strength, enabling
the cable suited for large span installation, resulting in time and installation cost savings. The suspension
wire, being an integral part of the cable, is easily available for gripping, fastening and pulling. This cable is
featured of its lightness, low dispersion and high tensile strength.
Description
The cable consists of 5 to 36 fibers containing tubes or fillers stranded in up to 3 layers around a central
strength member and bound under a PE jacket. Each jelly filled tube contains 4 -12 fibers. Solid or stranded
Construction
Suspension Wire
Opcal Fiber
Physical Properties
Fiber Nominal Nominal Nominal Outer Nominal Outer Maximum Pulling/Tensile Load
Count Weight Weight Diameter Diameter Installation Operating
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
2-24 389.0 261.07 12.6*25.1 0.50*0.99 2670/600 890/200
36-72 429.0 287.92 14.7*27.1 0.58*1.07 2670/600 890/200
96-144 571.0 383.22 20.2*32.6 0.80*1.29 2670/600 890/200
19
Ʒ
FIG8 SELF-SUPPORTING CABLE
Ʒ
Ʒ
Physical Properties
Maximum Pulling/Tensile Load
Fiber Nominal Nominal Nominal Outer Nominal Outer
Count Weight Weight Diameter Diameter Installation Operating
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
Construction
Ʒ
Ʒ
Armoured Type
Physical Properties
Maximum Pulling/Tensile Load
Fiber Nominal Nominal Nominal Outer Nominal Outer
Count Weight Weight Diameter Diameter
Installation Operating
(kg/km) (lb/kft) (mm) (in)
(N/lb) (N/lb)
20
Ʒ
Ʒ
Ʒ FIG8 SELF-SUPPORTING CABLE
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:4000N for unarmoured cables;
Under installation: 20×OD 6000N for armoured cables
During operation: 10×OD for unarmoured cables; Repeated Impact: 4.4 N.m (J)
20×OD for armoured cables. Twist (Torsion): 180×10 times, 125×OD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.;
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +50ć(+158̧) Crush Resistance: 220N/cm (125lb/in)
Safety Compliance Ʒ
Ʒ
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliances
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640
Features
• Suitable for self supporting aerial, duct and direct burial installation
• Tear away messenger simplifies grounding
• Ripcord allows easy cable entry and jacket removal
• Compatible with existing Fig 8 hardware
• Flexible buffer tube simplifies routing and splicing.
• Loose tube jelly filled for superior fiber protection
• UV or moisture resistant for outdoor application
21
Ʒ
CENTRAL LOOSE TUBE RIBBON FIBER CABLE
Ʒ
Ʒ
Application
This cable can provide excellent transmission performance and protection of fibers in a variety of
field environments. It is usually used in long haul communication system, subscriber network system,
distribution, feeder network system and local area network system.
Description
Central loose tube cable contains one tube with 12 fiber ribbons, which is filled with water blocking gel.
The fiber ribbon can be easily separated by hand tool. Either aramid yarn or fiber glass is wound around
the tube to provide physical protection and tensile strength. The cable can be jacketed with either PE,
Fiber Optic Cables
PVC or LSZH though PE is the preferred option for water protection purpose. For direct burial, steel
wire armour or corrugated steel tape armour is applied with an optional inner jacket of either PVC or
PE. An optional Aluminium moisture tape can be incorporated under the jacket for water blocking and
shielding purpose. An optional ripcord can be put under the jacket to facilitate jacket removal.
Construction
Ʒ
Ʒ
"
!
"#$
"
"
Unarmoured Type
Physical Properties
Maximum Pulling/Tensile Load
Fiber Nominal Nominal Nominal Outer Nominal Outer
Count Weight Weight Diameter Diameter Installation Operating
(kg/km) (lb/kft) (mm) (in) (N/lb) (N/lb)
22
Ʒ
Ʒ
Ʒ CENTRAL LOOSE TUBE RIBBON FIBER CABLE
Construction
Physical Properties Ʒ
Ʒ
Fiber Nominal Nominal Nominal Outer Maximum Pulling/Tensile Load
Count Weight Weight Diameter
Installation Operating
(kg/km) (lb/kft) (mm)
(N/lb) (N/lb)
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:3000N
Under installation: 20×OD Repeated Impact: 4.4 N.m (J)
During operation: 10×OD for unarmoured cables Twist (Torsion): 180×10 times, 125×OD
20×OD for armoured cables. Cyclic Flexing: 25 cycles for armoured cables.;
Temperature Range: 100 cycles for unarmoured cables.
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) Crush Resistance: 263N/cm(150lb/in)
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧)
23
Ʒ
CENTRAL LOOSE TUBE RIBBON FIBER CABLE
Ʒ
Ʒ
Fiber Compliance
Temperature Cycling IEC60794-1-2-F2
Tensile Strength IEC60794-1-2-E1A
Crush IEC60794-1-2-E3
Impact IEC60794-1-2-E4
Repeated Bending IEC60794-1-2-E6
Torsion IEC60794-1-2-E7
Kink IEC60794-1-2-E10
Cable Bend IEC60794-1-2-E11
Fiber Optic Cables
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
Ʒ
Ʒ FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640
Features
• Large fiber counts with small cable diameter
• Highly adaptable to mass splicing
• Suitable for installation in pipeline
• High quality jelly filled loose tube provides the ribbon fiber satisfactory mechanical and
environmental protection.
• Ripcord allows easy jacket removal
• UV or moisture resistant for outdoor application
• Dry water blocking core design for ease of handling
24
Ʒ
Ʒ
Ʒ MULTI LOOSE TUBE RIBBON FIBER CABLE
Application
This cable can provide excellent transmission performance and protection of fibers in a variety of
field environments. It is usually used in long haul communication system, subscriber network system,
distribution, feeder network system and local area network system.
Description
The cable consists of 12 to 648 fibers containing tubes or fillers stranded in up to 3 layers around a central
strength member and bound under a PE jacket. Each tube contains 4 -12 ribbon fibers. Solid or stranded
steel wire coated with polyethylene is usually used as central strength member. Fiber glass reinforced
Construction
Unarmoured Type
25
Ʒ
MULTI LOOSE TUBE RIBBON FIBER CABLE
Ʒ
Ʒ
Physical Properties
Fiber Nominal Nominal Nominal Outer Nominal Outer Maximum Pulling/Tensile Load
Count Weight Weight Diameter Diameter
(kg/km) (lb/kft) (mm) (in) Installation Operating
(N/lb) (N/lb)
Construction
Ʒ
Ʒ
Armoured Type
Physical Properties
26
Ʒ
Ʒ
Ʒ MULTI LOOSE TUBE RIBBON FIBER CABLE
Mechanical Properties
Minimum Bending Radius: Maximum Compressive Load:4000N for unarmoured cables;
Under installation: 20×OD 6000N for armoured cables
During operation: 10×OD for unarmoured cables; Repeated Impact: 4.4 N.m (J)
20×OD for armoured cables Twist (Torsion): 180×10 times, 125×OD
Temperature Range: Cyclic Flexing: 25 cycles for armoured cables.;
Operating Temperature Range: -40ć(-40̧) to +70ć(+158̧) 100 cycles for unarmoured cables.
Storage Temperature Range: -50ć(-58̧) to +70ć(+158̧) Crush Resistance: 220N/cm(125lb/in)
Safety Compliance
General Purpose Grade Flammability Test: OFN(UL1581)
Riser Grade Flammability Test: OFNR/FT4 (UL1666)
Plenum Grade Flammability Test: OFNP/FT6(UL 910)
FRPVC Grade Flammability Test: IEC60332-1
LSZH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
LSFROH Grade Halogen Content Test: IEC 60754-1
Acidity Test: IEC 60754; Smoke Emission Test: IEC61034-1/2
Flammability Test: IEC60332-1 & IEC 60332-3C/A
FR Grade Fire Resistance Test: IEC 60331 / BS 6387 CWZ
Standard Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) CEA S 87-640
Features
• Large fiber counts with small cable diameter
• Highly adaptable to mass splicing
• Suitable for installation in pipeline
• High quality jelly filled loose tube provides the ribbon fiber satisfactory mechanical and
environmental protection.
• Ripcord allows easy jacket removal
• UV or moisture resistant for outdoor application
• Dry water blocking core design for ease of handling
27
Ʒ
ALL DIELECTRIC SELF-SUPPORTING (ADSS) CABLE
Ʒ
Ʒ
Application
The ĀAll Dielectric Self-supporting (ADSS)ā cable is designed for aerial self supporting application
at short, medium and long span distances. ADSS cable offers a rapid and economical means for
deployment by cable television operators, telephone companies and power utilities. It is adopted for
high voltage, middle, small span conditions in Power Transmission System or mazy terrain such as river
spanning, mountains.
Description
The cable consists of 5 to 36 fibers containing tubes or fillers stranded in up to 3 layers around a central
strength member and bound under a PE jacket. Each tube contains 6 -12 fibers. All the fibers in the cores
Fiber Optic Cables
are filled with water blocking gel. Fillers may be used to preserve the cable geometry. A water swelling
tape is helically wrapped around the cable core. Aramid yarns are helically laid to supply peripheral
strengthening of the cable. The outer jacket is tightly bounded over the aramid yarn layer. The cable
jacket incorporates an optional inner polyethylene jacket and an outer polyethylene or AT (anti-tracking)
jacket. When the induction on cable surface is above 12KV, anti-tracking sheath material (AT) will be
applied. With AT outer jacket, the maximum electric field strength at operating point can reach 35KV.
For long span application, a double jacket design can be considered. An optional ripcord can be put
under the jacket layer to faciliate its removal.
Ʒ
Ʒ Construction
Physical Properties
Ice + Wind: 0mm + 35m/sec Ice + Wind: 12mm + 30m/sec
Span Max.
Max. Working Max. Max.
(m) Cable O.D. Cable Weight
Tension Sag
Cable O.D. Cable Weight Working
Sag
(mm/in) (kg/km)/(lb/kft) (mm/in) (kg/km)/(lb/kft) Tension
(N/lb) (%) (%)
(N/lb)
100 13.9/5.472 152/102.01 7578/1704 2 13.8/0.543 150.0/100.67 6621/1489 2
200 14.3/0.562 161/108.05 10430/2346 3 14.1/0.555 157.0/105.37 9000/2024 3
400 15.9/0.625 199/133.56 23221/5223 3 15.4/0.606 187.0/125.50 19255/4331 3
500 16.7/0.657 220/147.65 30590/6881 3 16.1/0.633 204.0/136.91 24885/5598 3
600 16.3/0.641 209/140.27 26952/6063 4 15.7/0.618 196.0/131.54 22154/4983 4
800 16.5/0.649 216/144.97 29452/6625 5 15.9/0.625 201.0/134.90 24042/5408 6
1000 16.7/0.657 221/148.32 31271/7034 6 16.1/0.633 204.0/136.91 24407/5490 6
* Above table do not cover all of available types. Other ADSS cables can be manufactured upon customer's
request according to different span and sag environment.
28
Ʒ
Ʒ
Ʒ ALL DIELECTRIC SELF-SUPPORTING (ADSS) CABLE
Mechanical Properties
Fiber Compliance
Standard Compliance
Telcordia GR-20 RUS 7 CFR 1755.900 (REA PE-90) ICEA S 87-640 IEEE 1222
Features
• High capacity cable offer great flexibility for placement on overhead transmission towers,
eliminating the need for a support messenger.
• Dry core design and high tension strength capability suitable for toughest environmental and
electrical conditions.
• Fit for extra high voltage power lines without interruption of power service to the customers.
• Typical spans with 1%-1.5% installation sag
29
Ʒ
Overhead Power Ground Wire (OPGW) FIBER CABLE
Ʒ
Ʒ
Application
OPGW is a dual functioning cable performing the duties of a ground wire and also providing a patch for
the transmission of voice, video or data signals . The fibers are protected from environmental conditions
(lightning, short circuit, loading) to ensure reliability and longevity. The cable is designed to be installed
on transmission and distribution lines to carry voice, data and video communications, especially in
lighting waveform monitoring system, an observation system for overhead test line, maintenance
data information system, power line protection system, power line operation system, and unmanned
substation monitoring.
Description
Fiber Optic Cables
Central loose tube type---The fibers is placed loosely in a sealed and water resistant stainless steel tube
filled with water blocking gel. This tube provides protection to the fibers during installation and operation
under severe environmental conditions. Aluminium layer over the tube is optional. The stainless optical
tube is located at the center of the cable protected by single or multiple layers of aluminium clad steel
and aluminium alloy wires. The Aluminium-clad steel wires are shaped trapezoidally around the optical
unit to provide compact construction. The metallic wires provide mechanical strength to withstand
Ʒ severe installation and operating conditions, while achieving conductivity to control temperature rise
Ʒ during short circuit conditions.
This type can accommodate up to 48 fibers in a cable. Despite such a high fiber count in a single tube,
each optical fiber is clearly distinguishable utilizing a fiber identification system consisting of coloring
and the number of ring marks on it. This compact design features high mechanical strength and fault
current rating within a smaller diameter. The smaller diameter also results in excellent sag tension
performance.
Multi loose tube type--- The fibers is placed loosely in a sealed and water resistant stainless steel tube
filled with water blocking gel. Two or three stainless steel optical tubes are helically stranded in the inner
layer of a multiple-layer cable.
The multi loose tube type is designed mostly for very high fiber count requirement over 48 with the
maximum fiber count reaching 144. The multi loose tube type can meet the requirement of huge cross
and large current capacity.
Construction
30
Ʒ
Ʒ
Ʒ Overhead Power Ground Wire (OPGW) FIBER CABLE
* The effective sectional area of the single-layer design ranges from 50mm2 to 83mm2, suitable
* The effective sectional area of the double-layer design ranges from 90mm2 to 200mm2, suitable
* The effective sectional area of the three-layer design ranges from 200mm2 to 400mm2, suitable
for rated voltages of 380kV, 420kV and 500kV in European markets.
31
Ʒ
Overhead Power Ground Wire (OPGW) FIBER CABLE
Ʒ
Ʒ
Mechanical Properties
Fiber Compliance
Temperature Cycling IEC60794-1-2-F2 Repeated Bending IEC60794-1-2-E6
Tensile Strength IEC60794-1-2-E1A Torsion IEC60794-1-2-E7
Crush IEC60794-1-2-E3 Kink IEC60794-1-2-E10
Impact IEC60794-1-2-E4 Cable Bend IEC60794-1-2-E11
Ʒ
Ʒ Cool Bend IEC60794-1-2-E11
Standard Compliance
IEEE 1138-1994
Features
• Colored coded fibers and binders for quick and easy identification during installation.
• Compact design results in excellent sag tension performance of the cable
• Aluminium-clad steel wires and Aluminium alloy wires provides mechanical strength to
withstand the installation and operating conditions, while achieving conductivity required to
control temperature rise, during the short circuit fault condition
• Optical unit placed inside the Aluminium tube provides exceptional mechanical and thermal
protection for the fiber against severe environments and external laternal force.
• Thick walled Aluminium tubes provide hermetic seal for optical units, providing excellent
crush resistance and low resistivity.
• Unique design has maximum allowable tension to control fiber strain
• Stranded wires used for optimizing the mechanical and electrical properties of the cables
• High load, long span capability.
32
Ʒ
Ʒ
Ʒ Ordering Information
Yu Fire retardant PVC (FRPVC) Fire retardant PVC will not allow fire to propagate along the cable
when ignited. Fire retardant PVC jacketed cables will usually meet
the flammability requirements of UL 1581(VW-1) and IEC 60332-1.
With special design, the cables can meet IEC 60332-3A/C or UL
1666 (OFNR riser grade or UL 910 (OFNP plenum grade).
H Low smoke and Halogen-free, LSZH material is used mostly for indoor applications. When
(LSZH) exposed to fire it will retard fire propagation while emitting non toxic
corrosive halogen gases (halogen free as per IEC 60754-1 and IEC
60754-2) and low amounts of smoke emission as per IEC 61034-2.
LSZH cables can usually meet the flammability requirement of UL
1581(VW-1) and IEC 60332-1. With special design, the cables can
meet IEC 60332-3A/C.
33
Ʒ
Ordering Information
Ʒ
Ʒ
AG Fiber Glass yarn + Aramid yarn The weakest aspect of aramid yarn is its compressive strength and
that is one of the strong points of fiberglass yarn. Putting the two
together combines the tensile strength, toughness, and light weight of
aramid yarn with the compressive strength and rigidity of fiberglass
yarn.
FG Fire Resisting Fiber Glass yarn Fiber glass is characterized by its hazard proof and soft nature.
Special fiber glass yarn can be used as both a strength member and
fire barrier for meeting IEC 60331
Armour Options
Ʒ
Ʒ Blank No armouring
T Corrugated steel tape armour Steel tape is corrugated to enhance the flexibility of the cable. Steel
tape armour is used to provide mechanical protection and rodent
resistance. The steel tape armour is usually offered with either
PE, PVC or LSZH inner jacket. It is not recommended to use
PVC for outer jacket. Compared with steel wire armour, it has the
advantage of lower cost, increased torsional stiffness and reduced
cable diameter
J Fiberglass armour Flexible dielectric armour is made of a thick layer of fiber glass
roving, It is a dielectric with high modulus and low weight glass.
Fiberglass armour is used when there is a need for dielectric and
high flexibility. Fiberglass armour is a fraction of weight of the
steel wire armour for identical performance level.
W Steel wire armour Helical wrap of galvanized steel wire armour provides the best
protection against rodent attack and mechanical damage, also
offering high tensile strength and crush resistance.
TW Corrugated steel tape armour The double armour is designed for underwater application. The
+ Steel wire armour double armour wires provide the necessary tensile stiffness needed
during installation to prevent excessive strain of the optical fibers,
mechanical protection from outside disturbances, as well as the
structural strength needed for underwater cables as relatively long
lengths of cable must be lifted to bring the cable to the water's
surface for servicing. Without the strength provided by the double
armour, the weight of the cable could break the optical fibers at the
point of lifting the cable.
B Bronze armour The braided bronze armour is used for increased mechanical
protection for offshore and shipboard cables. With this design, the
cable can pass IEC60332-3A. The bronze armour layer may also
be used to assist in locating buried cables. This is accomplished by
imparting a signal to the bronze armour and detecting the signal by
suitable above-ground apparatus.
34
Ʒ
Ʒ
Ʒ Ordering Information
Y Polyvinyl Chloride (PVC) PVC is mostly used mostly for indoor applications. It is most
Yu Fire retardant PVC (FRPVC) Fire retardant PVC will not allow fire to propagate along the cable
when ignited. Fire retardant PVC jacketed cables will usually meet
the flammability requirements of UL 1581(VW-1) and IEC 60332-1.
With special design, the cables can meet IEC 60332-3A/C or UL
1666 (OFNR riser grade or UL 910 (OFNP plenum grade).
Ʒ
Ʒ
H Halogen-free, Fire-retardant LSZH material is used mostly for indoor applications. When
(LSFH) exposed to fire it will retard fire propagation while emitting non toxic
corrosive halogen gases (halogen free as per IEC 60754-1 and IEC
60754-2) and low amounts of smoke emission as per IEC 61034-2.
LSZH cables can usually meet the flammability requirement of UL
1581(VW-1) and IEC 60332-1. With special design, the cables can
meet IEC 60332-3A/C.
4Y Polyamide/Nylon (PA) The nylon sheath provides necessary protection against rodents
and termites and the smooth surface of nylon makes laying of
cables in duct much easier. This material does not degrade the cable
mechanical properties or causes environmental damage.
11Y Polyurethane (PU) PU is used for harsh environments requiring very high flexibility.
This cable material is characterized by its good resistance to
humidity, moisture and weather, high flexibility, stable electrical
characteristics, and excellent resistance to abrasion or chemicals PU
provides good tear strength, providing cut-resistance in many rugged
environment. With special design, the cables may include a flame
retarding additive.
35
Ʒ
Ordering Information
Ʒ
Ʒ
Fiber Options
9 9.3/125um standard single mode This most employed fiber has a simple step index structure. It is
fiber per ITU-T G.652D (SMF) optimized for operation at the 1300 nm band and can also operate
in the 1550 nm, but it is not optimized for this region. The typical
chromatic dispersion at 1550nm is high at 17ps/nm-km. Dispersion
compensation must be employed for high-bit-rate applications. The
attenuation is typically 0.2dB/km at 1550nm and the PMD is less
than 0.1ps/km. This fiber is designed for use in long distance, high
bandwidth systems such as telecommunication and CATV.
2 9.3/125um low water peak non The ITU-T G.652 standard SMFs are not optimized for WDM
Fiber Optic Cables
dispersion shifted single mode applications due to the high attenuation around the water peak region.
fiber per ITU-T G.652C ITU G.652.C-compliant fibers offer extremely low attenuation
around the OH peaks. The G.652.C fiber is optimized for networks
where transmission occurs across a broad range of wavelengths
from 1285 nm to 1625 nm. Although G.652.C-compliant fibers
offer excellent capabilities for shorter, unamplified metro and
access networks, they do not fully address the needs for 1550-nm
transmission. The attenuation parameter for G.652 fiber is typically
0.2 dB/km at 1550 nm, and the PMD parameter is less than 0.1 ps/
km.
Ʒ
Ʒ
3 Dispersion Shifted single mode Conventional SMF has a zero-dispersion wavelength that falls near
fiber per G.653 (DSF) the 1310-nm window band. SMF shows high dispersion values over
the range between 1500 nm and 1600 nm (third window band).
The trend of shifting the operating transmission wavelength from
1310 nm to 1550 nm initiated the development of a fiber type called
dispersion-shifted fiber (DSF). DSF exhibits a zero-dispersion value
around the 1550-nm wavelength where the attenuation is minimum.
The DSFs are optimized for operating in the region between 1500
to 1600 nm. With the introduction of WDM systems, however,
channels allocated near 1550 nm in DSF are seriously affected by
noise induced as a result of nonlinear effects caused by FWM. This
initiated the development of NZDSF. G.653 fiber is rarely deployed
any more and has been superseded by G.655.
8 Non-Zero Dispersion Shifted Using nonzero dispersion-shifted fiber (NZDSF) can mitigate
single mode fiber per G.655 nonlinear characteristics. NZDSF fiber overcomes these effects
(NZDSF) by moving the zero-dispersion wavelength outside the 1550-nm
operating window. The practical effect of this is to have a small but
finite amount of chromatic dispersion at 1550 nm, which minimizes
nonlinear effects, such as FWM, SPM, and XPM, which are seen
in the dense wavelength-division multiplexed (DWDM) systems
without the need for costly dispersion compensation. There are
two fiber families called nonzero dispersion (NZD+ and NZD–), in
which the zero-dispersion value falls before and after the 1550-nm
wavelength, respectively. The typical chromatic dispersion for
G.655 fiber at 1550 nm is 4.5 ps/nm-km. The attenuation for G.655
fiber is typically 0.2 dB/km at 1550 nm, and the PMD is less than
0.1 ps/ km.
36
Ʒ
Ʒ
Ʒ Ordering Information
7 Non-Zero Dispersion Shifted In order to overcome the defects of G652 and G655 optical fibers,
single mode fiber per G.656 G656 fiber is developed. G656 fibers are designed for use in
(NZDSF) long haul transmission system and metro network. CWDM and
DWDM can also be applied on S+C+L bands with these types fiber.
These fibers are manufactured by PCVD process. The minimum
dispersion value from 1460nm to 1625nm is greater than 2ps/nm
km; the maximum value is less than 14ps/nm km. The effective
area at 1550nm is around 52 to 66μm. The excellent polarization
mode dispersion properties help the fiber to meet the requirement
of high bit rate transmission. The PMD co efficiency of these fibers
is less 0.05 ps/km. By use of improved PCVD process, excellent
4 Laser optimized 50/125um OM3 MMF has a 50-um nominal core diameter and a 125-um
multi mode fiber. OM3 grade nominal cladding diameter with a graded refractive index. The
per ISO/IEC 11801 attenuation parameter for OM3 fiber is typically 0.9 dB/km at
1300 nm. The main application for OM3 fiber is for 10G Ethernet Ʒ
Ʒ
network where very long transmission distance is required. This
fiber is optimized for use in the 850-nm band.
5 50/125um multi mode fiber per MMF has a 50-um nominal core diameter and a 125-um nominal
G.651. OM2 grade per ISO/IEC cladding diameter with a graded refractive index. The attenuation
11801(MMF) parameter for G.651 fiber is typically 0.9 dB/km at 1300 nm. The
main application for ITU-T G.651 fiber is for local area network.
This fiber is optimized for use in the 1300-nm band. It can also
operate in the 850-nm band.
6 62.5/125um multi mode fiber MMF has a 62.5-um nominal core diameter and a 125-um nominal
per ITU-T G651, OM1 grade cladding diameter with a graded refractive index. The attenuation
per ISO/IEC 11801. parameter for G.651 fiber is typically 0.9 dB/km at 1300 nm. The
main application for ITU-T G.651 fiber is for local area networks..
This fiber is optimized for use in the 1300-nm band. It can also
operate in the 850-nm band
37
Ʒ
Ordering Information
Ʒ
Ʒ
General Options
J Water-blocking gel in tubes For moderate protection of the fibers against water penetration.
only
JJ Water-blocking gel in tubes For better protection of the fibers against water penetration.
and in cable core interstices
JD Water-blocking gel in tubes and For better protection of the fibers against water penetration.
Fiber Optic Cables
VT Tight buffer The fibers are tightly buffered by a plastic material. Buffer diameter
is 0.9mm.
AT Anti-termite coating This is a special coating applied over the cable jacket to reduce the
damage of the cable by repelling insects and the termites. The anti
termite coating does not degrade the cable mechanical properties or
causes environmental damage.
AL Aluminium moisture barrier The aluminium moisture barrier tape offers extra protection against
tape water ingress. The tape is applied around the cable cores to form a
moisture barrier along the entire cable length.
OPGW Overhead Power Ground Wire Used in lighting waveform monitoring system, an observation system
for overhead test line, maintenance data information system, power
line protection system, power line operation system, and unmanned
substation monitoring.
ADSS All Dielectric Self Supporting For aerial self supporting aerial installation at short, medium and
long span distances. Adapted for high voltage, middle, small span
conditions in Power Transmission System or mazy terrain such as
river spanning, mountains.
SS Figure-8-self-supporting cable For self-supporting aerial installation, with steel messenger wire. The
Fig 8 cable is recommended for spans up to 150m. The messenger
wire is made of 7 stranded galvanized steel elements having a
diameter and tensile strength to match the cable weight.
R Ribbon Fiber For use in long haul communication system, subscriber network
system, distribution, feeder network system and local area network
system.
38
Ʒ
Ʒ
Ʒ ORDERING OPTIONS
D Duplex Cord
Simplex/Duplex Cord
Simplex: SA-B-C-D
Duplex: DA-B-C-D-E Ʒ
Ʒ
A: Cord Diameter
20=2.0mm; 25=2.5mm; 28=2.8mm; 30=3.0mm
B: Fiber Type
0=Fiber and copper conductors in cable
4=50/125 multi-mode fiber (OM3) per ITU-T G.651
5=50/125 multi-mode fiber (OM2) per ITU-T G.651
6=62.5/125 multi-mode fiber (OM1) per ITU-T G.651
7=NZDS SM fiber per ITU-T G.656.
8=NZDS SM fiber per ITU-T G.655.
9=Standard SM fiber per ITU-T G.652.D
D: Jacket Type
2Y=PVC, H=LSZH, ONR-OFNR PVC; ONP-OFNP FEP; Yu-FRPVC
E: Cable Shape
FT= Flat Cord; RD= Round Cord; ZIP= Zip Cord
39
Ʒ
ORDERING OPTIONS
Ʒ
Ʒ
Distribution: MTA-B-C-D-E-F-G-H-I-J-K-L
Breakout:BTA-B-C-D-E-F-G-H-I-J-K-L
40
Ʒ
Ʒ
Ʒ ORDERING OPTIONS
41
Ʒ
ORDERING OPTIONS
Ʒ
Ʒ
42
Ʒ
Ʒ
Ʒ ORDERING OPTIONS
43
Ʒ
ORDERING OPTIONS
Ʒ
Ʒ
A: Fiber type
0=Fiber and copper conductors in cable
4=50/125 multi-mode fiber(OM3)
5=50/125 multi-mode fiber(OM2)
6=50/125 multi-mode fiber(OM1)
7=NZDS SM fiber per G.656.
Fiber Optic Cables
44
Ʒ
Ʒ
Ʒ Optical & Geometrical Properties for Single Mode Fibers
45
Ʒ
Optical & Geometrical Properties for Multimode Fibers
Ʒ
Ʒ
Fiber Code 5 4 6 -
Core Non-Circularity ≤6 ≤6 %
Cladding Non-Circularity ≤2 1 ≤2 1 %
Core/Cladding Offset ≤3 ≤3 um
46
Ʒ
Ʒ
Ʒ Testing Method for Optical & Geometrical Properties of Fiber
47
Ʒ
Testing Method for Optical & Geometrical Properties of Fiber
Ʒ
Ʒ
EIA/
Testing IEC-
Parameter & Test Method Description TIA-455 ITU-T
Parameters 607931
FOTP
The wavelength at which a mode stops to propagate
is called cutoff wavelength for that mode; However,
an optical fiber is always able to propagate at least
one mode, the fundamental mode. The fundamental
mode can never be cut off. The cufoff wavelength of
a single mode fiber is the wavelength above which
Cutoff the fiber propagates only the fundamental mode G.650,
Wavelength Measuring the cutoff length involves comparing the 80 44 Methods5.3.1,
Fiber Optic Cables
(SMF) transmitted Power from the test fiber with that of a 5.3.3
reference fiber at different wavelength. TIA 455-80
& IEC 60793-1-44 provides methods for measuring
the cut-off wavelength of single-mode optical fibers.
The test method applies to sample fiber in either an
uncabled condition or in a cable or as a jumper cable.
Not all light travels through the core of the fiber, but
is distributed through both the core and the cladding.
Ʒ The "mode field" is the distribution of light through
Ʒ the core and cladding of a particular fiber. Mode-
Field Diameter (MFD) defines the size of the power
distribution. TIA/EIA 455-191establishes unifrom
requirement for measuring MFD of fiber. Four
methods are described in IEC 60793-1-45:a) direct
Mode Field far field scan b) variable aperture in the far field c)
G.650,
Diameter near field scan d) bidirectional backscattering using 191 45
an ODTR. Methods5.1.2
(SMF)
Mode field diameter is a key parameter because
the radial extent of the mode can be used to predict
losses at joints and microbends. In addition, if its
spectral variation is known, it can be used to measure
cut off wavelength. Other parameters which can
be predicted using MFD data include waveguide
dispersion and refractive index profile.
48
Ʒ
Ʒ
Ʒ Testing Method for Optical & Geometrical Properties of Fiber
49
Mechanical & Environmental Properties for Single Mode Fiber
Ʒ
Ʒ
Ʒ
Mechanical & Environmental Properties for Multi Mode Fiber
50
Ʒ
Ʒ
Ʒ Testing Method for Optical & Geometrical Properties of Fiber
Low & High This test measures the ability of the cable to retain its mechanical and
37 E11
Temperature Bend optical properties in spite of wide and rapid changes in temperature.
Fiber Stripability This test measures the forces required to remove the fiber coating. 178 B6
This test measures the effect of prolonged heat aging on the fiber. The
accelerated oxygen test simulates the result of long term aging on
Cable Aging the cable jacket. After test, the cable is examined for color changes, 82 F5
embrittlement, softening and surface damages etc.
This test is to determine whether the interstices within the cable is
Water Penetration continuously filled with jelly compound or water blocking to prevent 82 F5
water to enter the cable
This test is to determine whether the flooding compound will remain
Compound Flow stable for ambient temperature up to 70deg and will not drip, flow
or leak with age or at the change of temperature. No drip of the jelly 81 E14
(Drip)
compound may be observed during and after the test.
51
UNITED KINGDOM
Phoenix Place,
North Street, Lewes, East Sussex.
England, U.K. BN7 2QJ.
Te l : (44) 2074-195087
Fax: (44) 2078-319489
www.caledonian-cables.co.uk www.addison-cables.com
sales@caledonian-cables.co.uk sales@addison-cables.com