Professional Documents
Culture Documents
kr
LM201U05
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
( ) Preliminary Specification
( ■ ) Final Specification
SUFFIX SLA1
SIGNATURE DATE
LM201U05
Liquid Crystal Display
Product Specification
CONTENTS
LM201U05
Liquid Crystal Display
Product Specification
RECORD OF REVISIONS
Revision No Date Page Description
LM201U05
Liquid Crystal Display
Product Specification
1. General Description
The LM201U05-SLA1 s a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally black mode. This TFT-LCD has a 20.1 inch diagonally
measured active display area with UXGA resolution(1200 vertical by 1600 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus, presenting a palette of more than 16,777,216 colors.
The LM201U05-SLA1 has been designed to apply the interface method that enables low power, high speed,low
EMI. FPD Link must be used as a LVDS(Low Voltage Differential Signaling) chip.
The LM201U05-SLA1 is intended to support applications where thin thickness, wide viewing angle, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels,
the LM201U05-SLA1 characteristics provide an excellent flat panel display for office automation products such as
monitors.
G1
Gate Driver Circuit
LVDS
pair #1
CN1 Timing Controller
(30pin)
LVDS
&LVDS 1 Chip TFT - LCD Panel
pair #2 (1600 × RGB × 1200 pixels)
G1200
S1 S1600
+18V RGB
Power Circuit
Vcc Block Source Driver Circuit
CN1(4pin),CN2(2pin))
Back light Assembly (6CCFL)
CN3(2pin),CN4(4pin)
General Features
Active screen size 20.1 inches (510.54mm) diagonal
Outline Dimension 432.0(H) x 331.5(V) x 25.0(D) mm(Typ.)
Pixel Pitch 0.255 mm x 0.255 mm
Pixel Format 1600 horizontal By 1200 vertical Pixels RGB stripe arrangement
Color depth 8-bits, 16,777,216 colors
Luminance, white 300 cd/m2(Typ. Center 1 point)
Power Consumption Total 36.6 Watt(Typ.), ( 7.2 Watt @Vcc, 29.4 Watt @300cd/㎡ [Lamp=7.0mA])
Weight 3200g (Typ.)
Display operating mode Transmissive mode, normally black
Surface treatments Hard coating (3H), Anti-glare treatment of the front polarizer
LM201U05
Liquid Crystal Display
Product Specification
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 °C Max, and no condensation of water.
LM201U05
Liquid Crystal Display
Product Specification
3. Electrical Specifications
MODULE:
Power Supply Input Voltage VCC 17V 18V 19V Vdc
Power Supply Input Current ICC 0.40 0.60 A 1
Power Consumption Pc 7.2 10.8 W 1
Differential Impedance Zm 100 Ohm 2
Rush Current IRush 3 A 3
Notes :1. The specified current and power consumption are under the VCC=18.0V, 25°C, fV=60Hz condition,
Typical supply current is measured at the condition of 8 X 6 chess pattern (white & black)
and Max supply current is measured at the sub 1dot pattern.
2. This impedance value is for impedance matching between LVDS TX and
the mating connector of the LCD.
3. The duration of rush current is about 1ms.
4. Operating voltage is measured at 25°C. The variance of the voltage is ±10%.
5. The output voltage at the transformer in the inverter must be high considering to the loss of the
ballast capacitor in the inverter. The voltage above VS should be applied to the lamps for more
than 1 second for start-up. Otherwise, the lamps may not be turned on.
6. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this
may cause beat on the display. Therefore lamp frequency shall be as away possible from the
horizontal synchronous frequency and from its harmonics in order to prevent interference.
7. The lamp power consumption shown above does not include loss of external inverter at 25°C.
The used lamp current is the lamp typical current.
8. Let’s define the brightness of the lamp after being lighted for 5 minutes as 100%.
TS is the time required for the brightness of the center of the lamp to be not less than 95%.
The used lamp current is the lamp typical current.
9. The life time is defined as the time at which brightness of lamp is 50% compare to that of initial
value at the typical lamp current on condition of continuous operating at 25±2°C.
LM201U05
Liquid Crystal Display
Product Specification
The design of the inverter must have specifications for the lamp in LCD Assembly.
The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by
the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully
designed so as not to produce too much leakage current from high-voltage output of the inverter.
When you design or order the inverter, please make sure unwanted lighting caused by the mismatch
of the lamp and the inverter(no lighting, flicker, etc) never occurs. When you confirm it, the LCD –
Assembly should be operated in the same condition as installed in you instrument.
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp.
It shall help increase the lamp lifetime and reduce its leakage current.
a. The asymmetry rate of the inverter current and voltage waveform should be 10% below;
b. The distortion rate of the current and voltage waveform should be within √2 ±10%;
c. The ideal sine current and voltage waveform shall be symmetric in positive and negative polarities.
LM201U05
Liquid Crystal Display
Product Specification
3-2. Interface Connections
Interface chip must be used LVDS, part No. DS90CF383MTD(Transmitter) made by National Semiconductor.
Or used the compatible interface chips(TI:SN75LVDS83).
This LCD employs seven interface connections, a 30-pin connector is used for the module electronics interface.
Six 2-pin connectors are used for the integral back-light system.
The electronics interface connector is locking type and a model IS100-L30R-C23 manufactured by UJU or
FI-XB30SSRL-HF16 manufactured by JAE, The mating connector part number FI-X30M(JAE) or equivalent.
The pin configuration for the connector is shown in the table 3.
LM201U05
Liquid Crystal Display
Product Specification
3 NC NC
3 NC NC
Lamp 3
CN 2
Down Side
Lamp 4
CN 3
Lamp 5
CN 4
Lamp 6
LM201U05
Liquid Crystal Display
Product Specification
Frequency fV 59 60 61 Hz 3
-
Vertical Blank 30 40 50 tWV+ tVBP+ tVFP
LM201U05
Liquid Crystal Display
Product Specification
0.7Vcc
Hsync, Vsync, DE, DATA
0.3Vcc
tCLK
0.5VCC
Dclk
VALID
INVALID INVALID
DATA
DE(Data Enable)
tHP
Hsync tWH
DE(Data Enable)
LM201U05
Liquid Crystal Display
Product Specification
LM201U05
Liquid Crystal Display
Product Specification
90% 90%
T1 T2 T5 T6 T7
Valid data
Interface signal 10% 10%
0V T3 T4
LM201U05
Liquid Crystal Display
Product Specification
4. Optical Specifications
Optical characteristics are determined after the unit has been ‘ON’ for 30 minutes in a dark environment
at 25 °C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing
angle of Φ and θ equal to 0 °.
FIG. 1 presents additional information concerning the measurement equipment and method.
FIG. 1 Optical Characteristic Measurement Equipment and Method
LCD Module Pritchard 880 or
Optical Stage(x,y)
equivalent
50cm
Table 8. OPTICAL CHARACTERISTICS (Ta=25 °C, VCC=18.0V, fV=60Hz, Dclk=128MHz, IBL=7.0mArms)
Values
Parameter Symbol Units Notes
Min Typ MAx
Contrast Ratio CR 400 800 1
Surface Luminance, white LWH 250 300 cd/m2 2
Luminance Variation δ WHITE 70 - - % 3
Rise Time TrR - 7 ms 4
25
Response Time Decay Time TrD - 9 ms 4
TGTG_AVR - 8 - ms 5
Gray To Gray
TGTG_MAX - 14 - ms 5
Color Coordinates
RED RX 0.639
RY 0.342
GREEN GX 0.290
GY 0.615
-0.03 +0.03
BLUE BX 0.146
BY 0.072
WHITE WX 0.313
WY 0.329
Color shift 6
Horizontal θCST_H - 178 - degree
Vertical θCST_V - 178 -
Viewing Angle
Horizontal θH - 178 -
general degree 7
Vertical θV - 178 -
Horizontal θGMA_H - 178 -
Effective degree 8
Vertical θGMA_V 178
Gray Scale 2.2 9
LM201U05
Liquid Crystal Display
Product Specification
2. Surface luminance is the center point across the LCD surface 50cm from the surface with all
pixels displaying white under the condition of IBL = 7.0mArms . For more information see FIG 2.
3. The variation in surface luminance , δ WHITE is determined by measuring LON at each test
position 1 through 9, and then dividing the maximum LON of 9 points luminance by minimum LON
of 9 points luminance. For more information see FIG 2
H/2 H/2
H/10 H/10
V/10
P1 P2 P3
V/2
V
P4 P5 P6
V/2
V/10
P7 P8 P9
LM201U05
Liquid Crystal Display
Product Specification
4. The response time is defined as the following figure and shall be measured by switching
the input signal for “black” and “white”.
Response time is the time required for the display to transition from black to white (Rise Time,
TrR) and from white to black (Decay Time, TrD).
TrR TrD
100
90
Optical
Response
10
0
5. The Gray to Gray response time is defined as the following figure and shall be measured
by switching the input signal for “Gray To Gray “.
- Gray step : 5 Step
- TGTG_AVR is the total average time at rising time and falling time for “Gray To Gray “.
- TGTG_MAX is the max time at rising time or falling time for “Gray To Gray “.
Rising Time
Gray to Gray
G255 G191 G127 G63 G0
Falling Time G255
G191
G127
G63
G0
LM201U05
Liquid Crystal Display
Product Specification
6. Color shift is the angle at which the color difference is lower than 0.04.
- Color difference (Δu’v’)
4x 9y
u’= v’=
-2x + 12y + 3 -2x + 12y +3
u’1, v’1 : u’v’ value at viewing angle direction
Δu’v’ = (u’1-u’2)2+(v’1-v’2)2 u’2, v’2 : u’v’ value at front(θ=0)
θ = 0。
φ = 90。 z A
yu
(12:00)
θ
φ = 180。 φ = 0。
xl
(9:00) (3:00) xr
LM201U05
Liquid Crystal Display
Product Specification
7. Viewing angle(general) is the angle at which the contrast ratio is greater than 10.
8. Effective viewing angle is the angle at which the gamma shift of gray scale is lower than 0.3.
9. Grayscale Specification
0 0.125
31 1.20
63 4.57
95 11.3
127 21.4
159 35.2
191 52.8
223 74.4
255 100
LM201U05
Liquid Crystal Display
Product Specification
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LM201U05-SLA1 . In addition,
the figures in the next page are detailed mechanical drawing of the LCD.
Horizontal 413.0 mm
Bezel area
Vertical 311.0 mm
Horizontal 408.0 mm
Active display area
Vertical 306.0 mm
LM201U05
Liquid Crystal Display
Product Specification
<FRONT VIEW>
LM201U05
Liquid Crystal Display
Product Specification
<REAR VIEW>
LM201U05
Liquid Crystal Display
Product Specification
6. Reliability
LM201U05
Liquid Crystal Display
Product Specification
7. International Standards
7-1. Safety
a) UL 60950-1:2003, First Edition, Underwriters Laboratories, Inc.,
Standard for Safety of Information Technology Equipment.
b) CAN/CSA C22.2, No. 60950-1-03 1st Ed. April 1, 2003, Canadian Standards Association,
Standard for Safety of Information Technology Equipment.
c) EN 60950-1:2001, First Edition,
European Committee for Electrotechnical Standardization(CENELEC)
European Standard for Safety of Information Technology Equipment.
7-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992
b) C.I.S.P.R. “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ International Special Committee on Radio Interference.
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ European Committee for Electrotechnical Standardization.(CENELEC), 1998
( Including A1: 2000 )
LM201U05
Liquid Crystal Display
Product Specification
8. Packing
A B C D E F G H I J K L M
A,B,C : Inch
D : Year
E : Month
F : Panel Code
G : Factory Code
H : Assembly Code
I,J,K,L,M : Serial No
Note
1. Year
Year 97 98 99 2000 2001 2002 2003 2004 2005 2006 2007
Mark 7 8 9 0 1 2 3 4 5 6 7
2. Month
Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C
3. Panel Code
Panel Code P1 Factory P2 Factory P3 Factory P4 Factory P5 Factory Hydis Panel
Mark 1 2 3 4 5 H
4. Factory Code
Factory Code LPL Gumi LPL Nanjing
Mark K C
5. Serial No
Serial No. 1 ~ 99,999 100,000 ~
LM201U05
Liquid Crystal Display
Product Specification
9. PRECAUTIONS
Please pay attention to the following when you use this TFT LCD module.
LM201U05
Liquid Crystal Display
Product Specification
9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
LM201U05
Liquid Crystal Display
Product Specification
Pin # Pin Name Require Signal Pin # Pin Name Require Signal
1 VCC Power Supply for TTL Input 29 GND Ground pin for TTL
5 GND Ground pin for TTL 33 PLL GND Ground pin for PLL
8 D10 TTL Input (G6) 36 LVDS GND Ground pin for LVDS
9 VCC Power Supply for TTL Input 37 TxOUT3+ Positive LVDS differential data output 3
10 D11 TTL Input (G7) 38 TxOUT3- Negative LVDS differential data output 3
11 D12 TTL Input (G3) 39 TX CLKOUT+ Positive LVDS differential clock output
12 D13 TTL Input (G4) 40 TX CLKOUT- Negative LVDS differential clock output
13 GND Ground pin for TTL 41 TX OUT2+ Positive LVDS differential data output 2
14 D14 TTL Input (G5) 42 TX OUT2- Negative LVDS differential data output 2
15 D15 TTL Input (B0) 43 LVDS GND Ground pin for LVDS
16 D16 TTL Input (B6) 44 LVDS VCC Power Supply for LVDS
17 VCC Power Supply for TTL Input 45 TX OUT1+ Positive LVDS differential data output 1
18 D17 TTL Input (B7) 46 TX OUT1- Negative LVDS differential data output 1
19 D18 TTL Input (B1) 47 TX OUT0+ Positive LVDS differential data output 0
20 D19 TTL Input (B2) 48 TX OUT0- Negative LVDS differential data output 0
21 GND Ground pin for TTL Input 49 LVDS GND Ground pin for LVDS
LM201U05
Liquid Crystal Display
Product Specification