Professional Documents
Culture Documents
LG Check-Point Codes PDF
LG Check-Point Codes PDF
LG Checkpoint-codes
1
Hoofdstukindeling
- Variabel (aan/uit)..........................................................................................................26
AT-C.. / AT-H.. / LB-C.. / LB-D.. / LB-G.. / LB-H.. / LT-B.. / LT-C.. / LT-D.. / LT-E.. /
LV-B.. / P..AH
Multi-split ......................................................................................................................39
- Inverter
FM..AH
- Variabel (aan/uit)..........................................................................................................92
M..AC/AH
2
- Multi-split tot 2005.......................................................................................................94
A2-C.. / A3-C.. / A2-H.. / A3-H.. / LM..
RAC...............................................................................................................................96
- Standaard wandunit (aan/uit)......................................................................................97
LS-J.. / LS-K.. / LS-L.. / S..ACL / S..ACP / S..AH(P) / G..AH
3
LG
4
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
Is the resistance of
2.5Vdc
the sensor 10Ω / No 10kΩ
5kΩ at 25˚C? Correct connection
Ω V
Yes
CN-REMO
Is it normal ? No
Correct connection
Or change connection wire
Yes
Is it normal ? No
Correct connection
Or change the PCB
Yes
12Vdc 12Vdc
Check the installation of
wired remote controller. V V
(Noise interference)
Is it normal ? No
Adjust the state Check the Volt. Check the Volt.
of installation
- 68 -
6
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
CN-Float
Is it normal ? No
Check Drain Pump CN-Float
Yes
Is the float
No
switch clean ? ❊ Drain pump check
Clean float switch
Yes Check the wire
Check the wire connection (Open,
connection (Open, Soldered poorly)
Soldered poorly)
Is it normal ? No
Is it normal ? Correct connection
No
Or re-soldering PCB
Correct connection Yes
Yes Or re-soldering PCB
Is the resistance of
Drain Pump? Normal No
Is the resistance of f
( about 400Ω ) ? Change the Drain Pump
loat switch normal No
(short) ? Change the float switch Yes
Is the drain
No
pump clean ?
Clean drain pump
Yes
- 69 -
7
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
5. Trouble Shooting (UU..W & UU72 / 100)
6.9 Check code Trouble shooting CH09, CH10
Display
Title Cause of error Check point & Normal condition
code
Is it normal ? No
Remove obstruction
Yes
Is it normal ? No
Correct connection Or re-soldering PCB
Yes
Is it normal ? No
Change Indoor Motor
- 70 -
8
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
Is it normal ? No
Adjust the connection
Yes of wire Confirm the
wire of "Live",
Check the resistance "Neutral", "Signal"
between communication
line and GND.
(Normal : Over 2MΩ)
Is connector for
communication
correctly connected?
- 71 -
9
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
5. Trouble Shooting (UU..W & UU72 / 100)
6.11 Check code Trouble shooting CH21
Display
Title Cause of error Check point & Normal condition
code
• An instant over current in the U,V,W phase
- Comp lock
• Instant over current - The abnormal connection of U,V,W
21 DC Peak • Over Rated current • Over load condition
• Poor insulation of IPM - Overcharging of refrigerant
- Pipe length.
• Poor insulation of compressor
- 72 -
10
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
• Malfunction of compressor
22 Max. C/T • Over current • Blocking of pipe
• Low voltage input
• Refrigerant, pipe length, blocked, …
- 73 -
11
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
5. Trouble Shooting (UU..W & UU72 / 100)
6.13 Check code Trouble shooting CH40
Display
Title Cause of error Check point & Normal condition
code
→
Check Flow Chart
TRANS
Is it normal ?
( 230V±10%) No
Correct connection
Yes
- 74 -
12
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
→
23 140Vdc . • Check the power source.
Low voltage. • 3ph : DC link volt. is • Check the components.
→
250Vdc .
→
• Check the power source.
28 High voltage • 3ph : DC link volt. is • Check the components.
250Vdc .
→
• Abnormal Input voltage • Check the power source.
25 Input voltage
→
(140Vac , 300Vac ) • Check the components.
Is it normal ? No
Change CN_TRANS 1
Yes Compressor
- 75 -
13
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
5. Trouble Shooting (UU..W & UU72 / 100)
6.15 Check code Trouble shooting CH24
Display
Title Cause of error Check point & Normal condition
code
Is it normal ?
No
Re-vaccuming system
Yes & Re-charging
- 76 -
14
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
PSC Fault • Over current at • Check the component of “IGBT” /PFC module.
27 PFC Fault “IGBT”/PFC module • Check the components.
- 77 -
15
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
4. Trouble Shooting (UU..W & UU72 / 100)
Display
Title Cause of error Check point & Normal condition
code
1. Overload operation
(Pipe clogging/Covering/EEV defect/Ref. over-
charge)
Inverter compressor over Inverter compressor input
29 2. Compressor damage(Insulation damage/Motor
current current is over 30A
damage)
3. Input voltage low
4. ODU inverter PCB assembly damage
No Check
Is input voltage normal?
L~N phase is 220V ±15%
→ Check connection condition and wiring if power is
abnormal
Yes
Yes
- 90 -
16
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
5. Trouble Shooting (UU..W & UU72 / 100)
6.17 Check code Trouble shooting CH32, CH33
Display
Title Cause of error Check point & Normal condition
code
• Check the discharge pipe sensor for INV.
D-pipe (Inverter) • Check the install condition for over load.
• Discharge sensor
32 temp. high • Check the leakage of refrigerant.
(Inverter) temp. high
(105˚C )
→
• Check the SVC V/V open.
• Refer to sensor resistance table.
- 78 -
17
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Yes
No
Is Inverter PCB assembly normal? Replace inverter PCB assembly
Yes
- 115 -
18
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
6.18 Check code Trouble shooting CH41, CH44, CH45, CH46, CH47, CH65
Display
Title Cause of error Check point & Normal condition
code
- 79 -
19
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
5. Trouble Shooting (UU..W & UU72 / 100)
6.19 Check code Trouble shooting CH51, CH60
Display
Title Cause of error Check point & Normal condition
code
Check the
indoor unit combination
Is it normal ? No
Correct connection
Yes
Check PCB
Is it normal ? No
Correct connection
Yes
Change EEPROM
- 80 -
20
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Transmission error Main controller of Master 1. Power cable or transmission cable is not
between (Inverter PCB ➔ unit of Master unit can’t connected
52
receive signal from 2. Defect of outdoor Main fuse/Noise Filter
Main PCB)
inverter controller 3. Defect of outdoor Main / inverter PCB
Is transmission
LED (Yellow) of inverter No Is noise filter or fuse No
Replace noise filter or fuse
compressor normal?
PCB on?
Yes Yes
No
Is transmission cable
Re-connect transmission cable
connected correctly?
Yes
No
Is MAIN PCB normal? Replace MAIN PCB
Yes
Check Point
- Check the Transmission connector and LED (Main & Inverter)
48/56k
- 93 -
21
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) Troubleshooting Guide
Display
Title Cause of error Check point & Normal condition
code
Check Point
1. Check the connection condition of R,S,T wire.
2. Check the connection condition of CN_Phase.
3. Check the outdoor main fuse.
22
Single A: Inverter & Synchro
(UU..W & UU72 / 100) 5. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
- 81 -
23
Copyright ©2008 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
4. Trouble Shooting (UU..W & UU72 / 100)
Display
Title Cause of error Check point & Normal condition
code
1. Overload operation (Pipe clogging/Covering/EEV
defect/Ref.overcharge)
2. Compressor damage
AC input instant over cur- Inverter PCB input power
(Insulation damage/Motor damage)
73 rent error current is over 48A(peak)
3. Input voltage abnormal (L, N)
(Matter of software) for 2ms
4. Power line assemble condition abnormal
5. Inverter PCB assembly damage
(input current sensing part)
No Check
Is input voltage normal? L~N phase voltage is 220V ± 10%
→ Check connection condition and wiring if power is abnormal
Yes
Yes
No
Is inverter PCB assembly Check inverter PCB assembly IPM normality
normal? → Replace inverter PCB assembly
Yes
- 102 -
24
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Single A: Inverter & Synchro
(UU..W & UU72 / 100) Troubleshooting Guide
Display
Title Cause of error Check point & Normal condition
code
67 Outdoor fan • Outdoor fan is not oper- • Check the fan condition.
lock ating • Check the fan connector
Check Point
• CH 67 • CH 105
1. Check the install condition for fan. 1. Is communication line between the main PCB and the
fan PCB normal?
2. Is the communication LED on?
25
Single A
26
Single A: Aan/uit Single-split
(voor modellen, zie pag. 26) Troubleshooting Guide
Display
Title Cause of error Check point & Normal condition
code
• Open / Short
Indoor air sensor • Soldered poorly Normal resistor : 10K. / at 25°C (Unplugged)
01
• Internal circuit error Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
Normal resistor : 5K. / at 25°C (Unplugged)
02 Indoor inlet pipe sensor • Soldered poorly
Normal voltage : 2.5Vdc / at 25°C (plugged)
• Internal circuit error
• Open / Short
Normal resistor : 5K. / at 25°C (Unplugged)
06 Indoor outlet pipe sensor • Soldered poorly
Normal voltage : 2.5Vdc / at 25°C (plugged)
• Internal circuit error
10k. 2.5Vdc
. V
Check Point
1. Unplug the sensor on Indoor unit PCB.
2. Estimate the resistance of each sensor.
3. If the resistance of the sensor is 10K. / 5K. at 25°C, then sensor is normal.
4. If the resistance of the sensor is 0 K. or 8 , then sensor is abnormal. → Change the sensor.
5. Plug the sensor on Indoor unit PCB and Power ON.
6. Estimate the voltage of each sensor.
7. If the voltage of the sensor is 2.5Vdc at 25°C, then sensor is normal.
8. If the resistance of the sensor is 0 or 5Vdc, then sensor is abnormal. → Repair or Change the PCB.
27
Single A: Aan/uit Single-split
Troubleshooting Guide (voor modellen, zie pag. 26)
2) Troubleshooting CH03
Display
Title Cause of error Check point & Normal condition
code
• Connection of wire
Communication • Open / Short • Main PCB Volt. DC12V
03
Wired R/C • Wrong connection • Noise interference
12Vdc 12Vdc
V V
Check Point
1. Check the wire connection. (Open / Short) → Repair the connection
2. Check the soldering state of connector. (Soldered poorly) → Repair or Change the PCB.
3. Check the volt. Of main PCB power source. (DC 12V, DC 5V) → Repair or Change the main PCB.
4. Check the installation of wired remote controller. (Noise interference) → Adjust the state of installation
28
Single A: Aan/uit Single-split
(voor modellen, zie pag. 26) Troubleshooting Guide
3) Troubleshooting CH04
Display
Title Cause of error Check point & Normal condition
code
• The connection of wire(Drain pump/ Float switch)
Drain pump • Float switch Open. • Drain pump power input. (220V)
04
/ Float switch (Normal : short) • Drain tube installation.
• Indoor unit installation. (Inclination)
CN Float
CN-D/PUMP
CN-Float
0.
Check Point
1. Check the wire connection. (Open, Soldered poorly) → Repair the connection or change the PCB.
2. Check the resistance of float switch (Abnormal : Open, Normal : short) → Check the float switch.
3. Check the level of water
4. Check the volt. Of Drain pump power supply. (AC 230V) → Repair or Change the main PCB.
29
Single A: Aan/uit Single-split
Troubleshooting Guide (voor modellen, zie pag. 26)
Display
Title Cause of error Check point & Normal condition
code
• Power input AC 220V. (Outdoor, Indoor)
• The connector for transmission is disconnected.
05
• The connecting wires are misconnected.
/ Communication
• Communication poorly • The GND1,2 is not connected at main GND.
53 (Indoor → Outdoor)
• The communication line is shorted at GND.
• Transmission circuit of outdoor PCB is abnormal.
• Transmission circuit of indoor PCB is abnormal.
Check Point
1. Check the input power AC230V. (Outdoor, Indoor unit)
2. Check the communication wires are correctly connected.
→ Adjust the connection of wire
→ Confirm the wire of “Live”, “Neutral”
3. Check the resistance between communication line and
GND. (Normal : Over 2M. )
4. Check the connector for communication is correctly
connected.
5. Check the connection of GND1, GND2, and main GND.
6. If one indoor unit is operated normally, outdoor PCB is no
problem.
→ Check the another indoor unit.
* CH05 is displayed at indoor unit, CH53 is displayed at out-
door unit.
30
Single A: Aan/uit Single-split
(voor modellen, zie pag. 26) Troubleshooting Guide
5) Troubleshooting CH21
Display
Title Cause of error Check point & Normal condition
code
• An instant over current in the U,V,W phase
- Comp lock
• Instant over current - The abnormal connection of U,V,W
21 DC Peak • Over Rated current • Over load condition
• Poor insulation of IPM - Overcharging of refrigerant
- Pipe length.
• Poor insulation of compressor
Comp
U Resistance(. ) at 20°C
Inverter Constant
. Terminal
comp. comp.
V W U-V 0.64 0.8
V-W 0.64 0.8
W-U 0.64 0.8
Copper
Comp pipe Resistance(. ) at 20°C
Inverter Constant
Terminal
. comp. comp.
U-GND 2M. 2M.
V-GND 2M. 2M.
W-GND 2M. 2M.
Check Point
1. Check the wire connection. (U,V,W)
2. Check the load condition. (Refrigerant, Pipe length, …) → Adjust the load condition
3. Check the electricity leakage of the compressor. → Normal : Over 2M. .
4. Check the resistance of compressor. → Normal : 0.65. (INV), 0.8. (Cons.) → No difference at each terminal.
5. Check the insulation from water at IPM part. → Check the trace of water.
6. Check the IPM circuit.
31
Single A: Aan/uit Single-split
Troubleshooting Guide (voor modellen, zie pag. 26)
Display
Title Cause of error Check point & Normal condition
code
Malfunction of compressor
21 Max. C/T Blocking of pipe
Over current (14A ) Low voltage input
Refrigerant, pipe length, blocked, …
Check Point - +
1. Check the power source. + -
2. Check the fan operation is right.
+ -
3. Check the current.
4. Check the install condition.
5. Check the internal circuit. (C/T, Diode, Resistor)
Display
Title Cause of error Check point & Normal condition
code
TRANS1
50Hz, DC12V
CN PRESS
CN TRNAS1
Check Point
• CH 24 • CH 25
1. Check the connection of “CN_PRESS” 1. Check the power source.
2. Check the install condition for over load. 2. Check the components
3. Check the SVC V/V open. (Trans1, B/Diode, Diode, Resistance)
Display
Title Cause of error Check point & Normal condition
code
D-Pipe temp.
Toff(105) °C
T2(95) °C
T1(90) °C
COMP Frequency
Normal Normal OFF
(Hz)
LEV Openness Normal Normal OFF Control
(Pulse)
Check Point
• CH 32 • CH 33
1. Check the install condition for over load. 1. Check the install condition for over load.
2. Check the SVC V/V open. 2. Check the SVC V/V open.
3. Check the leakage of refrigerant. 3. Check the leakage of refrigerant.
4. Check the constant compressor. (same with CH21)
34
Single A: Aan/uit Single-split
(voor modellen, zie pag. 26) Troubleshooting Guide
Display
Title Cause of error Check point & Normal condition
code
• Open / Short
41 • Normal resistor : 200K. / at 25°C (Unplugged)
D-pipe sensor (Inverter) • Soldered poorly
• Normal voltage : 4.5Vdc / at 25°C (plugged)
• Internal circuit error
• Open / Short
44 • Soldered poorly • Normal resistor : 10K. / at 25°C (Unplugged)
Air sensor
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
45 Condenser Pipe sensor • Soldered poorly • Normal resistor : 5K. / at 25°C (Unplugged)
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
Suction Pipe sensor • Soldered poorly • Normal resistor : 5K. / at 25°C (Unplugged)
46
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
D-pipe sensor (Constant) • Soldered poorly • Normal resistor : 200K. / at 25°C (Unplugged)
47
• Internal circuit error • Normal voltage : 4.5Vdc / at 25°C (plugged)
• Open / Short
Heat sink sensor • Soldered poorly • Normal resistor : 10K. / at 25°C (Unplugged)
65
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
Check Point
1. Estimate the resistance of each sensor.(Unplugged)
2. Estimate the voltage of each sensor.(Plugged)
3. If the resistance of the sensor is 0 k. or 8 , then sensor is abnormal.
. If the voltage of the sensor is 0 V or 5Vdc, then sensor is abnormal.
35
Single A: Aan/uit Single-split
Troubleshooting Guide (voor modellen, zie pag. 26)
Display
Title Cause of error Check point & Normal condition
code
Check Point
• CH 51 • CH 60
1. Check the indoor unit capacity. 1. Check the insertion condition of EEPROM.
2. Check the poor soldering
36
Single A: Aan/Uit Single-split
(voor modellen, zie pag. 26) Troubleshooting Guide
Display
Title Cause of error Check point & Normal condition
code
Toff °C
T2 °C
T1 °C
COMP Frequency
Normal Normal OFF Normal
(Hz)
Check Point
• CH 61 • CH 62
1. Check the install condition for over load. 1. Check the fan is locked.
(Refrigerant, Pipe length, Blocked, …) 2. Check the Outdoor temp. is very high.
37
Single A: Aan/uit Single-split
(voor modellen, zie pag. 26)
Troubleshooting Guide
Troubleshooting CH54
Display
Title Cause of error Check point & Normal condition
code
U V W
Phase_A
5.3 msec
Phase_B
Phase_C
1 1 1 0 0 0
0 0 1 1 1 0
1 0 0 0 1 1
Check Point
1. Check the Main power.
2. Check the connecting state of connector CN_3PHASE on the outdoor pcb ass'y.
38
LG
Multi-split
Inverter
FM..AH
39
Multi-split: Inverter
FM..AH 4. Trouble Shooting
• Open / Short
Normal resistor : 5KΩ/ at 25°C (Unplugged)
02 Indoor inlet pipe sensor • Soldered poorly
Normal voltage : 2.5Vdc / at 25°C (plugged)
• Internal circuit error
• Open / Short
Normal resistor : 5KΩ/ at 25°C (Unplugged)
06 Indoor outlet pipe sensor • Soldered poorly
Normal voltage : 2.5Vdc / at 25°C (plugged)
• Internal circuit error
10kΩ 2.5Vdc
Ω V
Check Point
1. Unplug the sensor on Indoor unit PCB.
2. Estimate the resistance of each sensor.
3. If the resistance of the sensor is 10KΩ/ 5KΩ at 25°C, then sensor is normal.
4. If the resistance of the sensor is 0 KΩ or ∞, then sensor is abnormal. → Change the sensor.
5. Plug the sensor on Indoor unit PCB and Power ON.
6. Estimate the voltage of each sensor.
7. If the voltage of the sensor is 2.5Vdc at 25°C, then sensor is normal.
8. If the resistance of the sensor is 0 or 5Vdc, then sensor is abnormal. → Repair or Change the PCB.
- 59 -
40
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
• Connection of wire
Communication • Open / Short • Main PCB Volt. DC12V
03
Wired R/C • Wrong connection • Noise interference
12Vdc 12Vdc
V V
Check Point
1. Check the wire connection. (Open / Short) → Repair the connection
2. Check the soldering state of connector. (Soldered poorly) → Repair or Change the PCB.
3. Check the volt. Of main PCB power source. (DC 12V, DC 5V) → Repair or Change the main PCB.
4. Check the installation of wired remote controller. (Noise interference) → Adjust the state of installation
- 60 -
41
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
• The connection of wire(Drain pump/ Float switch)
Drain pump • Float switch Open. • Drain pump power input. (220V)
04
/ Float switch (Normal : short) • Drain tube installation.
• Indoor unit installation. (Inclination)
CN Float
CN-D/PUMP
CN-Float
0Ω
Check Point
1. Check the wire connection. (Open, Soldered poorly) → Repair the connection or change the PCB.
2. Check the resistance of float switch (Abnormal : Open, Normal : short) → Check the float switch.
3. Check the level of water
4. Check the volt. Of Drain pump power supply. (AC 230V) → Repair or Change the main PCB.
- 61 -
42
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
6.7 Troubleshooting Outdoor Error
▶FM15AH t/m FM25AH
Display
Title Cause of error Check point & Normal condition
code
• Power input AC 220V. (Outdoor, Indoor)
• The connector for transmission is disconnected.
05
• The connecting wires are misconnected.
/ Communication
• Communication poorly • The GND1,2 is not connected at main GND.
53 (Indoor → Outdoor)
• The communication line is shorted at GND.
• Transmission circuit of outdoor PCB is abnormal.
• Transmission circuit of indoor PCB is abnormal.
Check Point
1. Check the input power AC230V. (Outdoor, Indoor unit)
2. Check the communication wires are correctly connected.
→ Adjust the connection of wire
→ Confirm the wire of “Live”, “Neutral”
3. Check the resistance between communication line and
GND. (Normal : Over 2MΩ)
4. Check the connector for communication is correctly
connected.
5. Check the connection of GND1, GND2, and main GND.
6. If one indoor unit is operated normally, outdoor PCB is no
problem.
→ Check the another indoor unit.
* CH05 is displayed at indoor unit, CH53 is displayed at out-
door unit.
- 62 -
43
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
▶FM27AH t/m FM57AH
Display
Title Cause of error Check point & Normal condition
code
Check Point
1. Check the input power AC230V. (Outdoor, Indoor unit)
2. Check the communication wires are correctly connected.
Adjust the connection of wire Confirm the wire of "Live",
"Neutral"
3. Check the resistance between communication line and
GND. (Normal : Over 2MΩ)
4. Check the connector for communication is correctly con-
nected.
5. If one indoor unit is operated normally, outdoor PCB is no
problem.
Check the another indoor unit.
* CH05 is displayed at indoor unit, CH53 is displayed at
outdoor unit.
6. If all indoor unit is displayed CH05 but outdoor PCB not L N
display
CH53 : Check the CN_COM and CN_POWER is correctly
< TERMINAL BLOCK >
connected.
• 27/30/40k
1. In Case of CH53, Check the Connection → L , N at the ter-
minal block
• 48/56k
1. In Case of CH05, Check the Connection → CN-POWER,
CN-COMM at the Main PCB
2. In Case of CH53, Check the Connection → CN-COMM at
the Main PCB → L , N at the terminal block
L N
L N
CN-Power CN-COMM
- 72 -
44
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM27AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
• An instant over current in the U,V,W phase
- Comp lock
• Instant over current - The abnormal connection of U,V,W
DC PEAK • Over load condition
• Over Rated current
21 (IPM Fault) - Overcharging of refrigerant
• Poor insulation of IPM
Pipe length.
Outdoor Fan is stop
• Poor insulation of compressor
Yes
Copper
Comp pipe Resistance(Ω) at 20°C
Inverter
Terminal
comp.
Ω
U-GND 50MΩ
V-GND 50MΩ
W-GND 50MΩ
45
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
FM..AH 4. Trouble Shooting
1. Wait until inverter PCB DC voltage is discharged after main power off.
2. Pull out CN-L1(R), CN-L2(S), CN-L3(T) and CN-COMP Connector.
3. Set multi tester to resistance mode.
4. If the value between P and N terminal of IPM is short(0Ω) or open(hundreds MΩ), PCB needs to be replaced.(IPM damaged)
5. Set the multi tester to diode mode.
6. In case measured value is different from the table, PCB needs to be replaced.(PCB damaged).
P U V W Nu Nv Nw P U V W Nu Nv Nw
27 26 25 24 23 22 21 27 26 25 24 23 22 21
PFC_IPM check
U, V, W ➔ R S T
CAUTION
In case that the control box is opend and before checking electrical parts, it should be checked that the
LED 01M, 02M turned off(wait 7 minutes after main power OFF), otherwise it may cause electrical shock.
46
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
• An instant over current in the U,V,W phase
- Comp lock
• Instant over current - The abnormal connection of U,V,W
DC PEAK • Over load condition
• Over Rated current
21 (IPM Fault) - Overcharging of refrigerant
• Poor insulation of IPM
Pipe length.
Outdoor Fan is stop
• Poor insulation of compressor
Yes
Copper
Comp pipe Resistance(Ω) at 20°C
Inverter Constant
Terminal
Ω comp. comp.
U-GND 2MΩ 2MΩ
V-GND 2MΩ 2MΩ
W-GND 2MΩ 2MΩ
- 73 -
47
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
■FM27AH t/m FM41AH
LED01M LED02M
U,V,W CONNECTOR
1. Wait until inverter PCB DC voltage is discharged after main power off.
2. Pull out V, V, W COMP connector.
3. Set multi tester to resistance mode.
4. If the value between P and N terminal of IPM is short(0Ω) or open(hundreds MΩ), PCB needs to be replaced.(IPM damaged)
5. Set the multi tester to diode mode.
6. In case measured value is different from the table, PCB needs to be replaced.(PCB damaged).
P U V W Nu Nv Nw P U V W Nu Nv Nw
27 26 25 24 23 22 21 27 26 25 24 23 22 21
PFC_IPM chec
U, V, W ➔ R S
CAUTION
In case that the control box is opend and before checking electrical parts, it should be checked that the
LED 01M, 02M turned off(wait 7 minutes after main power OFF), otherwise it may cause electrical shock.
48
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
■ FM49AH t/m FM57AH
U
V
W
LED01M LED02M
CN(N)_BLUE CN(L)_BRWON
U,V,W CONNECTOR
1. Wait until inverter PCB DC voltage is discharged after main power off.
2. Pull out CN(L), CN(N) connectors and U,V,W COMP Connector.
3. Set multi tester to resistance mode.
4. If the value between P and N terminal of IPM is short(0Ω) or open(hundreds MΩ), PCB needs to be replaced.(IPM damaged)
5. Set the multi tester to diode mode.
6. In case measured value is different from the table, PCB needs to be replaced.(PCB damaged).
P U V W Nu Nv Nw P U V W Nu Nv Nw
27 26 25 24 23 22 21 27 26 25 24 23 22 21
PFC_IPM chec
U, V, W ➔ R S
CAUTION
In case that the control box is opend and before checking electrical parts, it should be checked that the
LED 01M, 02M turned off(wait 7 minutes after main power OFF), otherwise it may cause electrical shock.
- 75 -
49
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. Malfunction of Compressor
2. Blocking of Pipe
22 Max. C/T Input Over Current 3. Low Voltage Input
4. Refrigerant, Pipe length, Blocked...
Yes
1. Check inverter PCB assembly U,V,W connector
connection condition
Is compressor
No 2. Check wire disconnection and wiring
Wire connection
3. Check compressor terminal connection condition
condition normal?
(bad contact)
→ Reassemble if abnormality found
Yes
Yes
No Check
Is input voltage normal? R~S/S~T/T~R phase voltage is 380V ±10%
R~N/S~N/T~N phase voltage is 220V ±10%
→ Check connection condition and wiring if power is
Yes abnormal.
Yes
- 108 -
50
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
FM..AH 4. Trouble Shooting
Check Point
1. Check the power source.(200~240V)
2. Check the fan operation is right.
3. Check the current.
4. Check the install condition.
5. Check the CT Sensor Output signal (Check output pin 1.2 of the CT Sensor : 5V )
Tester
CT Sensor Output
(at the INVERTER PCB)
- 109 -
51
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
FM27AH t/m FM57AH Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. Malfunction of Compressor
Input Over
2. Blocking of Pipe
22 Max. C/T Current(27/30/40k-17A↑ 3. Low Voltage Input
48/56k-29A↑ ) 4. Refrigerant, Pipe length, Blocked...
Yes
1. Check inverter PCB assembly U,V,W connector
connection condition
Is compressor
No 2. Check wire disconnection and wiring
Wire connection
3. Check compressor terminal connection condition
condition normal?
(bad contact)
→ Reassemble if abnormality found
Yes
Yes
No Check
Is input voltage normal? L~N phase is 220V ±15%
→ Check connection condition and wiring if power is
abnormal
Yes
Yes
- 76 -
52
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
Check Point
1. Check the power source.(220V ±15%)
2. Check the fan operation is right.
3. Check the current.
4. Check the install condition.
5. Check the CT Sensor Output signal
(27/30/40k - Check output the CT Sensor : DC 2.5±0.2V)
(48/56k - Check output pin 1.2 of the CT Sensor : 5V )
Vdc
- 77 -
53
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
Yes
Yes
Yes
No
Is Inverter PCB Normal? Replace inverter PCB assembly
Yes
- 110 -
54
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM27AH
FM..AH 4. Trouble Shooting
Check Point
1. Check the Tab1 connection condition. (Refer to outdoor wiring diagram)
2. Check the CN_L1(R), CN_L2(S), CN_L3(T) connection condition
3. Check the DC Link voltage at not operating(380V↑ )
4. Check the DC Link voltage at Comp operating(500V↑ )
5. Check DC Link Sensing Signal (Refer the Picture)
Vdc
500Vdc ±10%
GND +
GND
Tester
DC Link Voltage
oltage INV
- 111 -
55
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
No
Is input voltage normal ? Check L~N Voltage is 220V±15%
Yes
No
Is Inverter PCB assembly Check connection from terminal block to
Power connection normal? Inverter PCB assembly CN(L), CN(N)
Yes
No
Is Inverter PCB Normal? Replace inverter PCB assembly
Yes
- 78 -
56
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
Check Point
1. Check the WCN_P(L),P(N) Connection condition at the Main PCB.(Refer to outdoor wiring diagram)
2. Check the DC Link voltage at not operating(280V↑ )
3. Check the DC Link voltage at Comp operating(340V↑ )
4. Check DC Link Sensing Signal :2.4~2.8V (Refer the Picture)
27/30/40k
Vdc
Vdc
- 79 -
57
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
N
GND L
< Inverter PCB> <DC Link Voltage Check Point> <Connection Check Point>
Vdc
DC_LINK
GND
- 80 -
58
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Yes
Yes
No
Is SVC valve open? Open SVC valve
Yes
Yes
Is high pressure No
more than 2500kPa Replace PCB
at manifold gauge?
Yes
Is high pressure of No
LGMV similar as Replace high pressure sensor
at manifold gauge?
Yes
- 81 -
59
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Check Point
1. Check the connection of H/press switch
2. Check short or not at the connector of high pressure switch (Normal open)
27/30/40k
< Main PCB : Connection Check Point > < Checking the Press switch >
48/56k
< Main PCB : Connection Check Point > < Checking the H/press switch >
- 82 -
60
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
Yes
No
Is Inverter PCB Normal? Replace inverter PCB assembly
Yes
<INVERTER PCB>
Tester
INPUT VOLTAGE
VOL AGE INV
- 112 -
61
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
No
Is input voltage normal ? Check L~N Voltage is 220V±15%
Yes
No
Is Inverter PCB Normal? Replace inverter PCB assembly
Yes
Check Point
1. Check the Input Voltage (L–N ➔ 220V±10%)
2. Check Input Voltage Sensor output voltage (2.5Vdc±10%)
- 83 -
62
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Vdc
< Inverter PCB> < Input Voltage Sensing Check Point >
INPUT(V)
GND
< Inverter PCB> < Input Voltage Sensing Check Point >
- 84 -
63
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Yes
- 85 -
64
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
FM27AH t/m FM57AH Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Yes
Check Point
1. Check the connection condition of PCB.
2. Check the connection condition of Comp. U,V,W wire.
3. Check the comp resistor and insulation resistance .
4. Check the IPM.(Refer 106 page) WVU
5. Check the pressure of refrigerant.
6. Check the Service Valve Open.
- 113 -
65
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. Overload operation (Pipe clogging/Covering/EEV
defect/Ref. overcharge)
2. Compressor damage (Insulation damage/Motor
Inverter PCB input
AC Input Instant over damage)
27 current is over100A(peak)
Current Error 3. Input voltage abnormal (L,N)
for 2us
4. Power line assemble condition abnormal
5. Inverter PCB assembly Damage (input current
sensing part)
No Check
Is input voltage normal? L~N phase voltage is 220V ±15%
→ Check connection condition and wiring if power is abnormal
Yes
Yes
No
Is inverter PCB assembly Check inverter PCB assembly PFCM normality
normal? → Replace inverter PCB assembly
Yes
CAUTION
PFCM module No.4,5 pins are internal short state. 8 1
- 86 -
66
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
No
Is input voltage normal ? Check L~N Voltage is 220V±15%
Yes
Yes
No
Is Inverter PCB Normal? Replace inverter PCB assembly
- 87 -
67
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
4. Trouble Shooting FM..AH
Check Point
1. Check the CN_(L),CN_(N) Connection condition at the Inverter PCB.(Refer to outdoor wiring diagram)
2. Check the DC Link voltage at not operating(280V↑ )
3. Check the DC Link voltage at Comp operating(340V↑ )
4. Check DC Link Sensing Signal : 2.4~2.8V (Refer the Picture)
27/30/40k
Vdc
Vdc
- 88 -
68
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
48/56k
Vdc
N
GND L
< Inverter PCB> <DC Link Voltage Check Point> <Connection Check Point>
Vdc
DC_LINK
GND
- 89 -
69
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. Overload operation
(Pipe clogging/Covering/EEV defect/Ref. over-
charge)
Inverter compressor over Inverter compressor input
29 2. Compressor damage(Insulation damage/Motor
current current is over 30A
damage)
3. Input voltage low
4. ODU inverter PCB assembly damage
No Check
Is input voltage normal?
L~N phase is 220V ±15%
→ Check connection condition and wiring if power is
abnormal
Yes
Yes
- 90 -
70
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
D-Pipe temp.
Toff(105) °C
T2(95) °C
T1(90) °C
COMP Frequency
Normal Normal OFF
(Hz)
LEV Openness Normal Normal OFF Control
(Pulse)
Check Point
• CH 32 • CH 33
1. Check the install condition for over load. 1. Check the install condition for over load.
2. Check the SVC V/V open. 2. Check the SVC V/V open.
3. Check the leakage of refrigerant. 3. Check the leakage of refrigerant.
4. Check the constant compressor. (same with CH21)
- 68 -
71
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Yes
No
Is Inverter PCB assembly normal? Replace inverter PCB assembly
Yes
- 115 -
72
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
• Malfunction of current detection circuit.
(Open / Short)
C/T • The voltage of "C01N" Is 4.0Vdc(25A) .
40 • Initial current error
Sensor Error • Check CT Sensor output voltage : 2.5Vdc
±5%
Yes
Yes
Tester
CT Sensor Output
(at the INVERTER PCB)
GND
COMP CURRENT
U,V ,W
U,V,W
<INVERTER PCB>
INPUT
VOL AGE INV
VOLTAGE
- 116 -
73
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
No
Is input voltage normal ? Check L~N Voltage is 220V±15%
Yes
No
Is Inverter PCB Normal? Replace inverter PCB assembly
Yes
Check Point
1. Check the Input Voltage (L–N ➔ 220V±10%)
2. Check Input Voltage Sensor output voltage (2.5Vdc±10%)
- 91 -
74
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Vdc
1
2
3
INPUT(CT)
GND
- 92 -
75
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
• Open / Short
41 • Normal resistor : 200KΩ / at 25°C (Unplugged)
D-pipe sensor (Inverter) • Soldered poorly
• Normal voltage : 4.5Vdc / at 25°C (plugged)
• Internal circuit error
• Open / Short
44 • Soldered poorly • Normal resistor : 10KΩ / at 25°C (Unplugged)
Air sensor
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
45 Condenser Pipe sensor • Soldered poorly • Normal resistor : 5KΩ / at 25°C (Unplugged)
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
Suction Pipe sensor • Soldered poorly • Normal resistor : 5KΩ / at 25°C (Unplugged)
46
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
• Open / Short
D-pipe sensor (Constant) • Soldered poorly • Normal resistor : 200KΩ / at 25°C (Unplugged)
47
• Internal circuit error • Normal voltage : 4.5Vdc / at 25°C (plugged)
• Open / Short
Heat sink sensor • Soldered poorly • Normal resistor : 10KΩ / at 25°C (Unplugged)
65
• Internal circuit error • Normal voltage : 2.5Vdc / at 25°C (plugged)
Check Point
1. Estimate the resistance of each sensor.(Unplugged)
2. Estimate the voltage of each sensor.(Plugged)
3. If the resistance of the sensor is 0 kΩ or ∞, then sensor is abnormal.
Ω If the voltage of the sensor is 0 V or 5Vdc, then sensor is abnormal.
- 69 -
76
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
FM15AH t/m FM25AH Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
Check Point
• CH 51 • CH 60
1. Check the indoor unit capacity. 1. Check the insertion condition of EEPROM.
2. Check the poor soldering
- 70 -
77
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM41 t/m FM57AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
Check Point
• CH 51 • CH 60
1. Check the indoor unit capacity. 1. Check the insertion condition of EEPROM.
2. Check the poor soldering
- 118 -
78
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
Transmission error Main controller of Master 1. Power cable or transmission cable is not
between (Inverter PCB ➔ unit of Master unit can’t connected
52
receive signal from 2. Defect of outdoor Main fuse/Noise Filter
Main PCB)
inverter controller 3. Defect of outdoor Main / inverter PCB
Is transmission
LED (Yellow) of inverter No Is noise filter or fuse No
Replace noise filter or fuse
compressor normal?
PCB on?
Yes Yes
No
Is transmission cable
Re-connect transmission cable
connected correctly?
Yes
No
Is MAIN PCB normal? Replace MAIN PCB
Yes
Check Point
- Check the Transmission connector and LED (Main & Inverter)
48/56k
- 93 -
79
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
T-N
R S T N
R S T
Fuse
R S T N
R S T N G
<Terminal Block&Fuse Check>
<Noise Filter Connection Check>
CN-L3(T) CN-L1(R)
CN-AC-220V
CN-L2(S)
Yes
No
Is inverter PCB assembly normal? Replace inverter PCB assembly
Yes
No
MAIN PCB assembly normal? Replace MAIN PCB assembly
Yes
Check Point
- Check the EEPROM Check sum & Direction
27/30/40k
- 94 -
81
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
FM49AH t/m FM57AH
<MAIN PCB>
<Inverter PCB>
- 95 -
82
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
Heat sink sensor • Heat sink sensor detect- • Check the Heat sink sensor (10kΩ ±10% at 25°C)
62 temp. high ed high temp.(85°C) • Check that outdoor fan is driving rightly
Gd`sRhmjပ
Snee 8/°C
S1 74°C
S0 7/°C
α α α
ქኩ༯ Ⴓ ໎ཙ Gy ጒ Gy Gy Ⴓ
NEE
ZGy\ ქኩ༯ ხᄅ Cnvm ხᄅ Cnvm Cnvm ქኩ༯
Yes
Yes
No
Is normal Inverter PCB ? Replace the heatsink sensor
Yes
- 120 -
83
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. ODU fan locking
2. Heatsink assembly of INV PCB assemble
Inverter PCB heatsink
65 Heatsink High error condition abnormal
sensor is open or short
3. Defect of temperature sensing circuit part defect
of INV PCB
Is assemble condition Check assemble condition between INV PCB heatsink and
No
of INV PCB heatsink normal ? PFC & IPM module
→ Reassemble if abnormality found
Yes
Check resistance between NO.19 pin and NO.20 pin
of PFC module
Is PCB temperature No Check resistance between NO.24 pin and NO.25 pin
sensing part normal ? of PFC module
→ 7KΩ ±10%(at 25°C)
→ Replace PCB if abnormality found
Check Point
1. Check resistance between No.19 pin and NO.20 pin of PCB PFC module
2. Check resistance between No.24 pin and NO.25 pin of PCB PFC module - only 48/56k
3. Resistance value should be in 7kΩ ±10%.(at 25°C).
4. Check the PFC Module No.19, 20 and IPM Module No.24, 25 pin soldering condition.
- 98 -
84
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
FM27AH t/m FM40AH
PFCM :
Measuring resistance
between No.19,20 pin
PFCM : IPM :
Measuring resistance Measuring resistance
between No.19,20 pin between No.24,25 pin
- 99 -
85
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM15AH t/m FM25AH
FM..AH 4. Trouble Shooting
Display
Title Cause of error Check point & Normal condition
code
No
Is fan connector condition right ? Do right fan connector condition
Yes
No
Is Fan motor nomal? Change abnomal motor
Yes
- 121 -
86
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM27AH t/m FM57AH
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. ODU fan locking
Fan RPM is 10RPM or
2. Heatsink assembly of INV PCB assemble condi-
less for 5 sec. when ODU
67 Fan Lock Error tion abnormal
fan starts or 40 RPM or
3. Defect of temperature sensing circuit part defect
less after fan starting.
of INV PCB
Is ODU Fan Motor Assemble No Check ODU Fan Motor assemble condition and fan locking
condition normal? → Reassemble or replace if abnormality found
Yes
Yes
Yes
Yes
Check Point
1. Check voltage between 1pin and 4pin of Fan Mortor connector (Tester diode mode)
2. Voltage vaule should be in 1V ±0.2V.
- 100 -
87
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
FM27AH t/m FM41AH
Check voltage betwen
1pin and 4pin of fan motor
Fan motor
connector
Tester
<Main PCB>
<Inverter PCB>
- 101 -
88
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
Display
Title Cause of error Check point & Normal condition
code
1. Overload operation (Pipe clogging/Covering/EEV
defect/Ref.overcharge)
2. Compressor damage
AC input instant over cur- Inverter PCB input power
(Insulation damage/Motor damage)
73 rent error current is over 48A(peak)
3. Input voltage abnormal (L, N)
(Matter of software) for 2ms
4. Power line assemble condition abnormal
5. Inverter PCB assembly damage
(input current sensing part)
No Check
Is input voltage normal? L~N phase voltage is 220V ± 10%
→ Check connection condition and wiring if power is abnormal
Yes
Yes
No
Is inverter PCB assembly Check inverter PCB assembly IPM normality
normal? → Replace inverter PCB assembly
Yes
- 102 -
89
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
FM..AH 4. Trouble Shooting
27/30/40k
- 103 -
90
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
Multi-split: Inverter
4. Trouble Shooting FM..AH
48/56k
N L
N
L
< Input Power Source Check Point > < Inverter PCB wiring Check Point >
- 104 -
91
Copyright ©2007 LG Electronics. Inc. All right reserved.
LGE Internal Use Only
Only for training and service purposes
LG
Multi-split
Variabel (aan/uit)
M..AC/AH
92
Multi-split: Aan / Uit
M..AC / AH Functions
Signal Receptor
Receives the signals from the remote controller.(Signal receiving sound: two short beeps or one long beep.)
Operation Indication Lamps
On/Off
: Lights up during the system operation.
Sleep Mode : Lights up during Sleep Mode Auto operation.
Timer : Lights up during Timer operation.
Signal
receptor Defrost Mode : Lights up during Defrost Mode or Hot Start operation (Heat pump model only)
Operation indication lamps OUT OUTDOOR UNIT
DOOR OPERATION : Lights up during outdoor unit operation. (Cooling model only)
Receives the signals from the remote controller.(Signal receiving sound: two short beeps or one long beep.)
Operation Indication Lamps
On/Off : Lights up during the system operation.
Sleep Mode : Lights up during Sleep Mode Auto operation.
Timer : Lights up during Timer operation.
Defrost Mode : Lights up during Defrost Mode or Hot Start operation.(Heat pump model only)
Operation indication lamps
Outdoor unit operation : Lights up during outdoor unit operation.(Cooling model only)
Self-diagnosis Function
■ Error Indicator
• The function is to self-diagnoisis airconditioner and express the troubles identifically if there is any trouble.
• Error mark is ON/OFF for the operation LED of evaporator body in the same manner as the following table.
• If more than two troubles occur simultaneously, primarily the highest trouble fo error code is expressed.
• After error occurrence, if error is released, error LED is also released simultaneously.
• To operate again on the occurrence of error code, be sure to turn off the power and then turn on.
• Having or not of error code is different from Model.
Error Error LED Error contents SVC check point
Code (Indoor body operation LED)
5sec
(once)
• Indoor air temperature thermistor • Indoor air TH ass'y check
1 open/short.
3sec 3sec 3sec
(twice)
• Indoor inlet pipe temperature thermistor • Indoor inlet pipe TH ass'y
2 open/short. check
3sec 3sec
(5times)
• Poor communication
5 • Communication line/circuit
3sec
(6times)
• Indoor outlet pipe temperature • Indoor outlet pipe TH ass'y
6 thermistor open/shor check
3sec
(7times)
• Defferent Operation (Simultanueous • Operate indoor units only
7 operation of cooling and heating. heating or cooling mode.
3sec
(9times)
9 • Indoor EEP ROM data (Art type only) • Replace main PCB DC ASM
3sec
: ten digits
: one digits
93
Multi-split
A2-C..
A3-C..
A2-H..
A3-H..
LM..
94
Multi-split: Aan / Uit voor 2005
(modellen, zie pag. 105)
Display Function
1. Heating Model 2. Cooling Model
OUT
Defrost Indicator Compressor on Indicator DOOR
• Hot-start, Defrost
Self-diagnosis Function
■ Error Indicator
• The function is to self-diagnoisis airconditioner and express the troubles identifically if there is any trouble.
• Error mark is ON/OFF for the operation LED of evaporator body in the same manner as the following table.
• If more than two troubles occur simultaneously, primarily the highest trouble fo error code is expressed.
• After error occurrence, if error is released, error LED is also released simultaneously.
• To operate again on the occurrence of error code 12, be sure to pull out power cord and then re-insert.
• Having or not of error code is different from Model.
95
LG
RAC
96
RAC
97
RAC: AAN / UIT
Operation Standaard wandunit, Panel & Deluxe
Display Function
1. Heating Model 2. Cooling Model
• Hot-start, Deice
Self-diagnosis Function
Error Error Display LED
Error contents SVC check point
Code (Indoor body operation LED)
• Indoor room temperature
(once) thermistor open/short • Indoor Thermistor
1
• Indoor pipe temperature assembly check
3sec 3sec 3sec thermistor open/short.
98
LG
RAC
LS-N....
LS-Q....
LS-R....
S..AN
S..AW
99
RAC: Wandunit Inverter
LS-N/Q/R, S..AN & S..AW Troubleshooting Guide
Self-diagnosis function
1. The malfunction indicator of indoor (see the operating LED of the INDOOR)
Temp. of Heat sink is over 95°C. The operating LED will be blink- Restart compressor when Heat sink
4
/Heat sink TH. is short or open. ing 4 times. Temp is 85°C below.
Comunication error (serial The operating LED will be blink- The operation is off(enable to restart
5 comunication). ing 5 times. by remote controller).
DC peak error. The operating LED will be blink- Compressor will be turned off immediately.
6 ing 6 times. (not enable to restart by remote controller)
Running current is over- The operating LED will be blink- Compressor will be turned off immediately.
7 loaded. (CT2) ing 7 times. (not enable to restart by remote controller)
Indoor fan lock error The operating LED will be blink- The operation is off(enable to restart
8 ing 8 times.
(BLDC fan model) by remote controller).
Outdoor fan lock error The operating LED will be blink- The operation is off(enable to restart
9 ing 9 times.
(BLDC fan model) by remote controller).
D-PIPE TH is short or open. The operating LED will be blink- Compressor will be turned off immediately.
10 ing 10 times. (restart compressor when D-PIPE TH. is
recovred)
❈ Error code ➅, ➆ can’t be operated unless the power cord is removed.
2. The malfunction indicator of outdoor (see the LED01M on the outdoor PCB ass’y)
Comunication error (serial The LED01M will be blinking 5 The operation is off(enable to restart
5
comunication). times. by remote controller).
DC peak error. The LED01M will be blinking 6 Compressor will be turned off immediately.
6
times. (not enable to restart by remote controller)
Running current is over- The LED01M will be blinking 7 Compressor will be turned off immediately.
7
loaded. times. (not enable to restart by remote controller)
Outdoor fan lock error The LED01M will be blinking 9 The operation is off(enable to restart
9 (BLDC fan model) times. by remote controller).
D-PIPE TH is short or open. The LED01M will be blinking 10 Compressor will be turned off immediately.
10 (restart compressor when D-PIPE TH. is
times. recovered)
100
RAC
C09AW*
C12AW*
101
RAC: ART COOL Inverter
C09AW* & C12AW* Troubleshooting Guide
Self-diagnosis function
1. The malfunction indicator of indoor (see the operating LED of the INDOOR)
Temp. of Heat sink is over 95°C. The operating LED will be blink- Restart compressor when Heat sink
4
/Heat sink TH. is short or open. ing 4 times. Temp is 85°C below.
Comunication error (serial The operating LED will be blink- The operation is off(enable to restart
5 comunication). ing 5 times. by remote controller).
DC peak error. The operating LED will be blink- Compressor will be turned off immediately.
6 ing 6 times. (not enable to restart by remote controller)
Running current is over- The operating LED will be blink- Compressor will be turned off immediately.
7 loaded. (CT2) ing 7 times. (not enable to restart by remote controller)
Indoor fan lock error The operating LED will be blink- The operation is off(enable to restart
8 ing 8 times.
(BLDC fan model) by remote controller).
Outdoor fan lock error The operating LED will be blink- The operation is off(enable to restart
9 ing 9 times.
(BLDC fan model) by remote controller).
D-PIPE TH is short or open. The operating LED will be blink- Compressor will be turned off immediately.
10 ing 10 times. (restart compressor when D-PIPE TH. is
recovred)
❈ Error code ➅, ➆ can’t be operated unless the power cord is removed.
2. The malfunction indicator of outdoor (see the LED01M on the outdoor PCB ass’y)
Comunication error (serial The LED01M will be blinking 5 The operation is off(enable to restart
5
comunication). times. by remote controller).
DC peak error. The LED01M will be blinking 6 Compressor will be turned off immediately.
6
times. (not enable to restart by remote controller)
Running current is over- The LED01M will be blinking 7 Compressor will be turned off immediately.
7
loaded. times. (not enable to restart by remote controller)
Outdoor fan lock error The LED01M will be blinking 9 The operation is off(enable to restart
9 (BLDC fan model) times. by remote controller).
D-PIPE TH is short or open. The LED01M will be blinking 10 Compressor will be turned off immediately.
10 (restart compressor when D-PIPE TH. is
times. recovered)
102
LG
RAC
C18AW*
C24AW*
103
RAC: ART COOL Inverter
C18AW* & C24AW* Troubleshooting Guide
Self-diagnosis function
1. The malfunction indicator of indoor (see the operating LED of the INDOOR)
Outdoor TH. is short or open. The display show "C2" Keep operating state.
2
Temp. of Heat sink is over 95°C. The display show "C4" Restart compressor when Heat sink
4
/Heat sink TH. is short or open. Temp is 85°C below.
Comunication error (serial The display show "C5" The operation is off(enable to restart
5 comunication). by remote controller).
DC peak error. The display show "C6" Compressor will be turned off immediately.
6 (not enable to restart by remote controller)
Running current is over- The display show "C7" Compressor will be turned off immediately.
7 loaded. (CT2) (not enable to restart by remote controller)
Indoor fan lock error The display show "C8" The operation is off(enable to restart
8
(BLDC fan model) by remote controller).
Outdoor fan lock error The display show "C9" The operation is off(enable to restart
9
(BLDC fan model) by remote controller).
D-PIPE TH is short or open. The display show "CA" Compressor will be turned off immediately.
10 (restart compressor when D-PIPE TH. is
recovred)
❈ Error code ➅, ➆ can’t be operated unless the power cord is removed.
2. The malfunction indicator of outdoor (see the LED01M on the outdoor PCB ass’y)
Comunication error (serial The LED01M will be blinking 5 The operation is off(enable to restart
5
comunication). times. by remote controller).
DC peak error. The LED01M will be blinking 6 Compressor will be turned off immediately.
6
times. (not enable to restart by remote controller)
Running current is over- The LED01M will be blinking 7 Compressor will be turned off immediately.
7
loaded. times. (not enable to restart by remote controller)
Outdoor fan lock error The LED01M will be blinking 9 The operation is off(enable to restart
9 (BLDC fan model) times. by remote controller).
D-PIPE TH is short or open. The LED01M will be blinking 10 Compressor will be turned off immediately.
10 (restart compressor when D-PIPE TH. is
times. recovered)
104
RAC
A09AW
A12AW
A09AW1
A12AW1
105
RAC: ART COOL PANEL Inverter
A..AW & A..AW1 Troubleshooting Guide
5times 5times
• Communication error
5 O O OFF
3 sec 3 sec
6times 6times
• DC Peak error O O SHUT
6 3 sec DOWN
7times 7times
SHUT
7 • Over current error (CT2) O O
3 sec DOWN
8times 8times
• Indoor fan lock error
8 (BLDC fan model only) O OFF
3 sec
9times 9times
• Outdoor fan lock error
O O OFF
9 (BLDC fan model only)
3 sec
10 times 10 times
• D-Pipe TH. is short or open. O O ON
10
3 sec
106
RAC: ART COOL PANEL Inverter
A..AW & A..AW1 Troubleshooting Guide
Check flow
YES YES
No No No
Check flow
YES YES
No No No
107
RAC: ART COOL PANEL Inverter
Troubleshooting Guide A..AW & A..AW1
• 9K / 12K
Error code Description Cause of error
• Heat-sink TH. is damaged(short or open).
Heat-sink Temp. is over
95°C • Heat-sink Temp. is over 95°C
4
Heat-sink TH.
is open or short • Damage or defect on the sensing circuit of outdoor pcb assembly.
(R01H, R02H, C01H)
Check flow
YES YES
No No No
108
RAC: ART COOL PANEL Inverter
A..AW & A..AW1 Troubleshooting Guide
Check flow
YES YES
Is the voltage of T/Block
Wiring connection Is the voltage of GND & DC5V in
, in outdoor about
Is right ? Outdoor pcb about DC 5V ?
AC 220/240V ?
No No No
Indoor Outdoor
1(BR) 1(BR) Check power connector Check FUSE, NF01/02J, PTC,
2(BL) 2(BL) Is not connected to the Power Module, BD-01S in
3(GN/YL) 3(GN/YL) T/Block in indoor unit. Outdoor pcb assembly
4(RD) 4(RD)
YES YES
No No
Earth port
109
RAC: ART COOL PANEL Inverter
Troubleshooting Guide A..AW & A..AW1
Check flow
YES YES
Supplied voltage to Is connector (CN-U,V,W)
Outdoor pcb is about connected to compressor and Refrigerant pressure is right ?
AC 220/240V ? inserted to pcb in right position ?
No No No
YES YES
No No
U * 18 K Model
Check
. Short of SPM2 pins (GND – P, U, V, W pin)
Direction of D01Z~D03Z, C08Z,10Z,12Z,16Z
V W Assembling state of R01P ~ R21P & IC01P
Assembling state of screw between INV-IC &
Heat-sink
DC 15V output of Power module.
110
RAC: ART COOL PANEL Inverter
A..AW & A..AW1 Troubleshooting Guide
Check flow
YES YES
Supplied voltage to
Does indoor / outdoor fan work
Outdoor pcb is about Refrigerant pressure is right ?
normally ?
AC 220/240V ?
No No No
YES
No
111
RAC: ART COOL PANEL Inverter
Troubleshooting Guide A..AW & A..AW1
Check flow
YES YES
Indoor fan is rotating ? (1) Indoor fan is rotating ? (2) DC–fan driving circuit is right ?
No No No
Outdoor fan is locked • Outdoor fan is locked by an obstacle (ex : branch of tree, bar…etc)
9 (BLDC fan model only)
• Fan connector is not connected to outdoor pcb assembly
• Defective in DC-fan driving circuit
Check flow
YES YES
Outdoor fan is rotating ? (1) Outdoor fan is rotating ? (2) DC–fan driving circuit is right ?
No No No
112
RAC: ART COOL PANEL Inverter
A..AW & A..AW1 Troubleshooting Guide
Check flow
YES YES
No No No
113