Professional Documents
Culture Documents
Motor IEC PDF
Motor IEC PDF
SELECTION GUIDE
AC Induction Motor
112-280 Frame
B-426
January, 2002
DUTY MASTER AC MOTORS IEC SELECTION GUIDE
Effective 06/01/01, Supersedes all previously dated pages.
KW RPM FRAME AIR LIST PRICE KW RPM FRAME AIR LIST PRICE
VELOCITY VELOCITY
4 3000 112M 600CM/SEC $1045 37 3000 200L 600CM/SEC $5145
4 1500 112M 500 1023 37 1500 200L 500 4667
4 1000 132M 600 1408 37 1000 225M 700 7366
4 750 160M 400 1936 37 750 250S 650 9576
5.5 3000 132S 600 1067 45 3000 225S 600 6647
5.5 1500 132S 500 1062 45 1500 225S 500 6652
5.5 1000 160M 600 1782 45 1000 250S 800 8689
5.5 750 160L 400 2189 45 750 250M 650 11970
7.5 3000 132S 600 1254 55 3000 225M 600 8390
7.5 1500 132M 500 1287 55 1500 225M 500 8484
7.5 1000 160L 600 2200 55 1000 250M 800 10164
7.5 750 180M 475 2441 55 750 280S 750 12831
11 3000 160M 600 1733 75 3000 250M 900 11235
11 1500 160M 500 1700 75 1500 250M 800 10353
11 1000 180M 600 2793 75 1000 280S 900 13860
11 750 180L 475 3276 75 750 280M 750 16674
15 3000 160L 600 2156 90 3000 280S 900 14800
15 1500 160L 500 2134 90 1500 280S 800 13445
15 1000 180L 600 3423 90 1000 280M 900 17661
15 750 200M 475 3990 90 750 280K 750 18454
18.5 3000 180M 600 2546 110 3000 280M 900 1785
18.5 1500 180M 500 2426 110 1500 280M 800 15813
18.5 1000 200M 700 4158 110 1000 280K 900 19950
18.5 750 200L 475 4988 132 3000 280M 900 19247
22 3000 180L 600 2982 132 1500 280K 800 17504
22 1500 180L 500 2835 150 3000 280M 900 22444
22 1000 200L 700 4804 150 1500 280K 800 18995
22 750 225S 500 6484
30 3000 200M 600 3953
30 1500 200M 500 3780
30 1000 225S 700 6458
30 750 225M 500 7875
USE OF MODIFICATIONS
Read carefully all details and explanatory notes for each modification
These modifications are designed to be added to the base list price of a Totally Enclosed Fan Cooled (IC41), Totally
Enclosed Non-Ventilated (IC40), or Totally Enclosed Air Over (IC48) motor. Adding these modifications to any other
enclosure may result in price discrepancies.
DISCOUNTS
All modified motors will be subject to the multiplier and discount symbol of the base price motor unless a specific modification
calls out a change in discount symbol and/or multiplier.
CHANGE NOTICE
All change notices requiring a product change will be subject to a $100 NET re-specification charge plus the applicable
modification adder. If the change notice is received within two weeks of scheduled ship date, the change will be priced at the
applicable MOD center charges. This policy does not pertain to paperwork changes (i.e. territory number changes or “ship to”
addresses).
ALTITUDE
The ratings listed in this selection guide apply to energy efficient motors operating at an altitude up to 1000 meters above sea
level with a “B: temperature rise up to 40 C ambient. When operating at a higher altitude derating may be necessary in order to
maintain the motor’s operating temperature. The following derate factor should be used for rerating the nameplate KW.
(1) Motors requiring a combination of Ambient and Altitude must first refer to AC Product Marketing for pricing and
availability.
(2) Motors are based using sine wave power, if motor is applied to an Inverter as well as requiring High Altitude conditions
it must first be reviewed by AC Product Marketing for the need of special features and/or a special design to meet the
application.
AMBIENT
The ratings listed in this selection guide apply to energy efficient motors operating at ambients up to 40 C with a “B”
temperature rise up to 1000m above sea level. When operating at a higher ambient derating may be necessary in order to
maintain the motor’s operating temperature. The following derate factor should be used for rerating the nameplate KW.
AMBIENT 45 C 50 C 55 C 60 C 65 C
CLASS B TEMPERATURE LIMITS 96% 93% 89% 85% 80%
CLASS F TEMPERATURE LIMITS 100% 100% 100% 100% 98%
(1) Motors requiring a combination of Ambient and Altitude please refer to AC Product Marketing for pricing and
availability.
(2) Motors are based on a motor using sine wave power, if motor is applied on an Inverter as well as requiring High
Ambient conditions must first be reviewed by AC Product Marketing for the need of special features and/or special
design to meet the application.
BALANCE
All motors are dynamically balanced and vibration measured in accordance with IEC standards. Modified motors can be built to
exceed standard limits as outlined below.
VELOCITY (mm/s R.M.S.) 3000 RPM (1) 1500 RPM & SLOWER
STANDARD 2.8 1.8
ULTRA-STANDARD 1.8 1.12
PRECISION 1.12 .71
ULTRA-PRECISION .71 .45
(1) Ultra-Precison balance of .45 is not available on two pole (3000RPM) motors.
Vibration level of motors in field are usually higher than when measured per the IEC procedure
mm/s refers to Velocity, millimeters per second R.M.S.
Vibration is measured on all three axes using five separate locations
Vibration at frequencies other than running speed will be less than values noted above
Motors with roller bearings are not available with vibration limits at the Precision or Ultra-Balance levels
BEARINGS
ROLLER BEARINGS
A motor equipped with roller bearings must be belt duty and is not suitable for coupled service.
Roller bearings are available on the drive end of modified motors on 1500RPM or slower, 160 frames and up for above standard
overhung loads.
(1) Frames 160 to 250 a Roller Bearing is optional depending on the belt load application. For 280 frames on belt duty
applications a Roller Bearing on the drive end of the motor must be ordered, and the above price addition added and
written on the order entry form.
SEALED/SHIELDED/OPEN BEARINGS
Bearing location must be specified on order. Indicate whether FE, BE, or BOTH. This adder is for standard ball bearings only
and not applicable to Thrust or Roller Bearings.
BEARING TYPE
SEALED SHIELDED BEARING OPEN BEARING
FRAME BEARING (SINGLE & DOUBLE) (IC41, IC40,IC48)
112-132 $105 $105 STD
160-200 $190 $190 STD
225 $235 $235 STD
250-280 N/A $375 STD
This modification may be used in lieu of sealed bearings where sealed bearings are not available, impractical, or undesirable.
This construction makes more grease available to the bearing raceway than does a sealed for life bearing and is available for all
bearing types including roller and thrust bearings. Order write-up must specify which bearing(s) to be sealed whether FE, BE,
or BOTH.
SPARE BEARINGS
For one set of spare bearings per motor ordered, use the list price adders from the table below.
(1) This adder is valid only for standard bearings – bearings with features or for conditions listed below are not covered by
this adder. Contact AC Product Marketing for quotations on these specialty items.
Specialty features/conditions not covered:
Special cages or other components
Motors having Ultra-Precision balance
Specific brands or characteristics to meet Customer specifications
Grease other than Chevron SRI-2/Dow Corning DC44/Shell Aero-Shell #7 for ball bearings or Mobil SHC-220 for
roller bearings
INSULATED BEARING
Available only on horizontal 280 frames. Contact AC Product Marketing for vertical applications.
Only one bearing needs to be insulated to break the electrical path. Reliance standard practice is to insulate the FE
(Opposite Drive End) bearing only.
Motors with a drive end roller bearing will always have only the FE (Opposite Drive End) insulated.
CONDUIT BOX
Note as standard all enclosures are provided with a cast iron conduit box with dual cable entry.
LOCATION
Standard conduit box location is side mounted on frames 112-280. Conduit box mounted on top of front-end bracket is available
on cast iron IC41, IC40, IC48 motors frames 112-280.
AUXILIARY/SEPARATE
A separate cast iron conduit box can be provided for space heaters or other control leads. NOTE: All accessory leads will be
brought out to the auxiliary conduit box. This modification includes the addition of a terminal strip.
ENCLOSURE 112 132 160 180 200 225 250 280 280K/H
IC41 $350 $350 $385 $385 $415 $415 $440 $440 $470
IC48 $350 $350 $385 $385 $415 $415 $440 $440 $470
IC40 $350 $350 $385 $385 $415 $415 $440 $440 $470
10
DIRECTION OF ROTATION
ROTATION ARROW / PHASE SEQUENCE
Standard Reliance IC41 motors utilize bi-directional cooling fans. When rotation direction is required to be called out on the
motor, a rotation arrow and phase sequence nameplate are supplied for $85.00 list . Direction of rotation shall be referenced
facing the opposite drive end of the motor.
11
DOCUMENTATION
When specified with the motor order, the following documentation is available for the net price addition for each item from the
table below. All data submittals include standard data transmittal and certification sheet – Item #1 below – in standard format.
Where data is required to be submitted to more than one location add $50 NET for each additional mailing address . Where
data is required for Customer Approval add $50 NET for each motor rating.
The data available is provided as quality black on white paper, suitable for reproduction. AS AN ALTERNATE to paper copies,
any engineering data, curve and drawing can be supplied in electronic format (. tif or .pdf file only) via email – specify email
address on order write-up. If both formats are required, add $25 NET plus the appropriate “ADDITIONAL COPIES” adder for
the table above.
12
DRAINS
DRAIN PLUGS AND BREATHERS
Standard horizontal IC41, IC48, IC40 motors with B3 or B3/L mounting are provided with drain holes that have Stainless Steel
T-Drains. For special mounting positions, vertical motors or special automatic drains, make list price additions from the table
below.
(1) This adder is for adding an additional T-Drain to the motor and therefore the location must be explained on the order
entry form.
A 9.53mm hole can be provided in the conduit box for a $130 list.
MOTOR
ENCLOSURE 112 132 160 180 200 225 250 280 280K/H
IC41, IC40, IC48 $210 $210 $310 $290 $360 $395 $415 $445 $445
MOTOR
ENCLOSURE 112 132 160 180 200 225 250 280 280K/H
IC41, IC40, IC48 $465 $515 $1,595 $2,615 $3,220 $3,960 $4,445 $5,065 $5,400
13
DUCTILE IRON
For remote locations, where an extra degree of reliability and protection is required, ductile iron components are available. In
addition, Ductile iron modifications will cause extended leadtimes. For delivery cycles, contact the manufacturing plant.
QTY 112 132 160 180 200 225 250 280 280K/H
1 $2,000 $2,100 $2,250 $2,400 $2,625 $3,150 $3,700 $4,430 $5,665
FRAME ONLY 2-4 $1,600 $1,675 $1,800 $1,915 $2,100 $2,515 $2,950 $3,545 $4,530
5+ $1,200 $1,260 $1,350 $1,440 $1,575 $1,890 $2,220 $2,655 $3,400
FRAME / END 1 $3,650 $3,850 $4,000 $4,500 $5,200 $6,200 $6,800 $8,100 $10,050
BRACKETS / 2-4 $2,900 $3,050 $3,200 $3,600 $4,150 $4,950 $5,425 $6,485 $8,015
CONDUIT BOX (1) 5+ $2,175 $2,280 $2,400 $2,700 $3,120 $3,720 $4,080 $4,875 $6,025
ENCLOSURES
IP55
As defined by IEC 34-5: Complete protection against contact with live or moving parts inside the enclosure. The entry of dust is
not totally prevented, but dust cannot enter in sufficient quantity to interfere with the satisfactory operation of the motor.
Projection of water by nozzle from a ny direction has no harmful effect.
IP56
As defined by IEC 34-5: Complete protection against contact with live or moving parts inside the enclosure. The entry of dust is
not totally prevented, but dust cannot enter in sufficient quantity to interfere with the satisfactory operation of the motor. Water
from heavy seas or projected from powerful jets has no harmful effect.
END SHEILDS
B-5 MOUNTING (FOOTLESS)
IEC FRAME 112 132 160 180 200 225 250 280
BOLT CIRCLE 215mm 265mm 300mm 300mm 350mm 400mm 500mm 500mm
FIT DIAMETER 180mm 230mm 250mm 250mm 300mm 350mm 450mm 450mm
“FF” FLANGE $295 $425 $565 $665 $945 $1,135 $1,355 $1,535
“FT” FLANGE $345 $475 $615 $715 $995 $1,185 $1,405 $1,585
14
Standard commercial export packaging for under deck export shipping is available at a Net Price addition of 8% of total motor
order with a Net Price minimum of $350 per sales order.
A wood slated crate specifically designed and recommended for air shipments is available for 160-280 frames.
FAN MATERIAL 112 132 160 180 200 225 250 280 280K/H
BRONZE (1) $315 $395 $725 $845 $940 $1,575 $1,810 $2,645 $2,675
ALUMINUM (1)(2) N/A N/A $725 $765 $805 $850 $920 $1,090 $1,100
(1) Motors with metal fans are provided with a steel or cast iron fan cover.
(2) Not available for motor speeds above 1500 RPM
FREQUENCY
On a production basis, 60Hz designs can be furnished for three-phase ratings. Apply the following percentage price adder to the
basic modified 50Hz rating of the required enclosure and RPM.
GROUNDING
The standard IEC motor B3 mounting is equipped with an internal ground and a tapped hole M10 X 1.5 on the foot of the motor.
GROUND PAD
Use the following list adder to provide a M10 X 1.5 tap; 25.4-mm thick pad mounted to the motor frame.
ENCLOSURE 112 132 160 180 200 225 250 280 280K/H
15
IC41, IC40, IC48 $155 $210 $260 $310 $390 $415 $440 $465 $490
INSULATION
TYPE OF INSULATION
The standard insulation system for IEC motors is Class F. For addition to Class F system.
INSULATION TYPE 112 132 160 180 200 225 250 280 280K/H
E N/C N/C $235 $415 $550 $730 $1,020 $1,400 $1,965
J $80 $105 $140 $230 $300 $375 $530 $730 $1,240
NOTE:
This insulation system is not suitable for a mbient temperatures below -25 C
LEADS
LEADS – EXTRA LONG
Leads longer than standard 152 mm are available. Use list adders from the table below for every 304 mm increments of added
length to a maximum length of 2.44 meters.
This modification provides for “potted” or “chicoed” lead opening between motor frame and conduit box. If an auxiliary conduit
box is required, double the list adder below to have both sets of leads sealed.
ENCLOSURE 112 132 160 180 200 225 250 280 280K/H
IP54, IP55, IP56 $390 $390 $395 $400 $410 $450 $460 $480 $500
16
TERMINAL BLOCKS
The terminal block is provided on IEC motors as an industry standard not as a requirement by IEC, at no additional charge.
These terminal blocks are designed to accept single hole lugs from the customer. The blocks will be sized with studs as follows,
the end users will have the responsibility to select the proper size lugs to fit the studs. The selection of a dual voltage motor will
eliminate the ability to supply terminal blocks with the standard product configuration.
FRAME SIZE 112 132 160 180 200 225 250 280 280K/H
STUD DIAMETER IN (mm) 6 6 6 6 8 8 10 12 16
CABLE GLAND
Metal industrial grade cable glands to conform to Reliance Electric’s standard configuration have a metric outlet opening. These
are available for all enclosures in frames 112-280 both horizontal and vertical. This adder is per conduit box; if an auxiliary
conduit box is required, double the adder below to have both equipped with cable glands.
It is necessary to provide the cable size/type with orders to minimize improper cable gland size and type selection. If the cable
size and type specified by the customer are incompatible with Reliance’s standard configuration, additional price adders, delivery
time and/or alternate specifications may be necessary.
FRAME SIZE 112 132 160 180 200 225 250 280 280K/H
CABLE DIA. IN (mm) 12-14 15-17 24-26 24-26 31-33 31-33 39-41 39-41 45-47
LUBRICATION
GREASE
Bearings furnished in 112 – 280 motors are lubricated with Chevron SRI-2 grease, with the exception of roller bearing
applications. Special greases for roller bearings must be reviewed by AC Product Marketing prior to quotation.
GREASE FITTINGS
Alemite type 1610 (Zerk Type) grease fittings for IC41, IC40, and IC48 enclosures are standard on modifiable 112-280 motors.
Two automatic grease relief fittings can be furnished on modified 112-280 motors for a list price adder of $30 .
17
“OIL MIST LUBRICATION” is available for IC41, IC40, and IC48 enclosures.
The motor modified using the adder will ship with inlet and outlet plugs installed, a special lubrication nameplate, sealed lead
entry into the frame and an insulation system and leads that are compatible with most lubricating oils. (if an auxiliary conduit
box is required, a separate adder for sealed leads for that box will also have to be made) Lubrication nameplate reads “Oil Mist
Lubrication” – this will indicate the motor must immediately be used on an oil mist system or filled with grease because at time
of shipment no lubricant will be provided. This modification requires the features of IP54, IP55, or IP56 motor.
MOUNTING POSITION 112 132 160 180 200 225 250 280 280K/H
HORIZONTAL 360 360 500 550 635 705 875 1250 1495
VERTICAL 500 500 610 675 775 865 1070 1475 1770
MOUNTING
VERTICAL FOOTLESS
This modification converts a horizontal foot mounted motor to a “FF” or “FT” Flange, footless vertical motor with vertical lifting
capability.
Vertical lifting capability is available ONLY for motors mounted shaft-down; motors mounted shaft-up will have lifting
arrangements as standard for horizontal motors. Please note on the Order Entry form if shaft-up “V3” or shaft-down “V1”
mounting. If shaft-down, a drip cover will be provided.
TYPE OF MOUNTING 112 132 160 180 200 225 250 280
“FF” or “FT FLANGE $450 $650 $895 $1,015 $1,425 $1,485 $1,775 $2,045
NAMEPLATES
NON-STANDARD MARKINGS
For non-standard markings on motor nameplates apply the following list price addition to the basic modified motor price. The
character height is only available in 2.38 mm. All other special character heights or special fonts must be authorized by AC
Product Marketing.
$75 LIST PER MOTOR
Motor identification nameplates for remote mounting by customer will be furnished when specified on order write-up.
Nameplates are available in a foreign language by adding the following list price addition per nameplate per translation. A
standard English motor nameplate will be provided on all motors in addition to the foreign nameplate.
18
To have a motor marked as “Suitable for variable frequency application,” apply the following addition to the basic modified
motor price.
(1) All motors will have Class F insulation rise, 40 C ambient, for an altitude of 1,000 meters maximum and 76 meters
maximum lead length from the AB or Reliance Drive. Otherwise consult your drive manufacturer for lead length
limitations.
(2) For motors used on the Reliance GV3000; this drive must have optimized Volts/Hz with additional boost as needed.
PAINT
The standard paint system is an epoxy base system with a 2 to 3 mil. Dry film thickness in Reliance Blue-Green color. Any
deviation from this description is considered a special finish and requires review.
This adder covers a special color of the standard Reliance finish ONLY. Customer MUST furnish a copy of the requested paint
specification with a reference to one of the following and a paint chip if possible.
Federal Standard 595
Munsell System
RAL Standards
Sherwin Williams reference number (must be standard, non-proprietary)
Carboline reference number (must be standard, non-proprietary)
Exact color matches to a specification or paint chip are NOT always possible – color match will only be approximate in most
cases. SPECIAL COLOR PAINT WILL CAUSE LEADTIME TO BE EXTENDED. Finishes other than Reliance standard
(regardless of color) must be reviewed by AC Product Marketing prior to quoting.
112-180 200-280
$375 $500
19
SHAFTS
SPECIAL SHAFT EXTENSIONS
Any deviation from the dimension of a single standard shaft extension or standard double shaft extension requires a price
addition from the modification bases.
NUMBER
REQUIREMENT OF 112 132 160 180 200 225 250 280 280K/H
MOTORS
TABLE 1 – SPECIAL SHAFT – BASIC ADDITION
BASIC PRICE QTY 1 $1355 $1435 $1515 $1590 $1665 $1740 $1815 $1890 $1965
ADDITION S FOR QTY 2-4 $555 $590 $620 $650 $685 $715 $745 $775 $800
SPECIAL SHAFT QTY 5+ $225 $235 $250 $260 $275 $285 $300 $310 $335
TABLE 2 – SPECIAL SHAFT FEATURES
FOR EACH ADDITIONAL 127mm
LENGTH (OR ANY PORTION $25 $35 $40 $50 $60 $65 $75 $85 $95
THEROF) (1)
#416 STAINLESS STEEL OR ANY
$105 $165 $230 $345 $630 $810 $1,170 1,260 $1,325
CLASS 2 MATERIAL
#304, 316 STAINLESS STEEL $280 $440 $605 $910 $1,650 $2,215 $3,075 $3,485 $3,485
17-4PH SHAFT MATERIAL $160 $250 $345 $520 $945 $,215 $1,755 $1,890 $1,990
FOR EACH FEATURE PER EACH END OF THE SHAFT ADD FROM THE TABLE BELOW:
KEYWAY (2) $35 45 50 60 75 85 90 105 110
DRILLED HOLE:DIAMETRICALLY $30 40 45 55 70 75 85 100 105
STEPS: EACH STEP OR REDUCED
$30 $40 $45 $55 $70 $75 $85 $100 $105
DIAMETER FROM STANDARD (3)
THREADS: CLASS 2 RIGHT HAND
THREAD OF SIZE APPROPRIATE
$40 $50 $60 $70 $90 $100 $110 $130 $140
TO SHAFT DIAMETER
1 end only (4)
TAPERED 31.75 mm OR 38.1 mm PER ANY
304.8 mm WITH THTREADS,
$40 $50 $60 $70 $90 $100 $110 $130 $140
LOCKNUT AND WASHER
1 end only (4)
HOLE DRILLED AND TAPPED IN END
OF SHAFT, (DEPTH LIMIT $40 $50 $60 $70 $90 $100 $110 $130 $140
TO 3 X DIAMETER)
SQUARED: MILLED FLATS
$40 $50 $60 $70 $90 $100 $110 $130 $140
1 end only (3) (4)
(1) For additional length greater than 4 times standard shaft diameter, contact AC Product Marketing for quotation.
(2) Standard endmill keyway in English dimensions only – for other types (sledrunner or woodruff) and/or for metric
dimensions, contact AC Product Marketing for quotation.
(3) For diameter less than one-half standard shaft diameter, contact AC Product Marketing for quotation.
(4) To make any of these modifications to both ends of shaft, contact Product Marketing for quotation.
20
SPACE HEATER
The space heater is a strip type heater mounted around the coil head of the motor with a maximum sheath temperature of 150 C.
The heater voltage will be 120 volts single phase unless otherwise specified. Other available single phase, single voltages are
available: 240V, 440V, or 575V with a + or – 10% variation, suitable for use on 50 or 60Hz power source.
MOTOR VOLTAGE ENCLOSURE 112 132 160 180 200 225 250 280 280K/H
600V MAX IC41, IC48, IC40 $175 $175 $255 $285 $285 $340 $415 $490 $570
ABOVE 600V IC41, IC48, IC40 $450 $450 $525 $525 $575 $575 $620 $680 $740
TESTS
Each Reliance motor is tested to assure conformance with electrical and mechanical specifications. Each motor is given a
Routine Test per IEEE Std. 112.
ROUTINE TEST
This is a test report per IEEE Std. 112 Appendix A and includes complete nameplate information. The test report does not
include Vibration data; this data requires an additional $50NET to the Routine Test & Report adder . Note the locked rotor
test which is included in Routine Test is a single phase locked rotor test. For a Three Phase Locked Rotor Test add an
additional $250 NET to the Reliance Test & Report adder.
COMPLETE TEST
A complete test uses a dynamometer to verify nameplate description and electrical design characteristics. After verification the
test results are supplied on a test report per IEEE Std. 112 Appendix B.
CALIBRATION TEST
Consists of 0 to 125% rated load test measurement of speed, torque, current, power factor and efficiency at rated voltage. The
data is provided as a curve plotted n Reliance standard format.
NOISE TEST
This verifies sound levels per procedures defined in IEEE-85 under a No Load Condition.
This is the recommended procedure for the measurement of insulation resistance of rotating machinery rated 1 HP (I KW) or
greater. Testing is done per IEEE #43, latest revision. Polarization Index is the ration of a 10 min. resistance with constant test
potential applied.
21
THERMISTORS
Thermistors are available for IC41, IC40 and IC48 Design N, 112-280, per pricing below. Note: lockrotor protection may not
be provided on 250 frames and larger.
The thermistor system consists of three PTC thermistors embedded in the motor windings plus a solid state control relay. The
solid state control relay is priced and shipped separately and is for customer mounting at a remote location. Should the customer
wish the control relay to be mounted on the motor, a separate conduit box s required.
112-132 160-280
Thermistors only $350 $350
Thermistors and relay (relay mounted by customer) $800 $800
Thermistors, relay (mounted by Reliance) and auxiliary conduit box $1,250 $1,250
22
connection. Resistance value (10, 100, 120 ohm) must be included on the order write up. Note: The temperature readout device
is not supplied by Reliance and must be ordered separately. Add $2,100 list per bearing.
TORQUE
STARTING TORQUE, HIGHER THAN IEC DESIGN “N”
Available 112-280 frames, single speed 1500, 1000, or 750 RPM motors only, which will be nameplates as a Design “N” motor.
STARTING TORQUE %
160-180 200-225 250-280
OF FULL LOAD
250% 25% 20% 15%
300% 30% 25% 20%
350% (1) (1) (1)
(1) Frame size may change – Contact AC Product Marketing for quote.
BREAKDOWN TORQUE %
160-180 200-225 250-280
OF FULL LOAD
225% 20% 15% 10%
250% 25% 20% 15%
300% 30% 25% 20%
350% (1) (1) (1)
400% (1) (1) (1)
(1) Frame size may change – Contact AC Product Marketing for quote.
23
VOLTAGE
For standard motor voltages by frequency see below. For special voltages in the range of 200 to 1000V, make the list price
addition from the table below. NOTE: As standard a 160L frame and up is connected for Wye-Start, Delta-Run where a 112 or
132 frame is normally a Wye connected motor.
50 HERTZ 60 HERTZ
220 230
380 460
400 575
415
VOLTAGE QTY 112 132 160 180 200 225 250 280 280K/H
1 $750 $1,050 $1,350 $1,625 $1,900 $2,200 $2,500 $2,800 $3,000
200 – 600
2-4 $425 $575 $725 $850 $950 $1,150 $1,300 $1,450 $1,550
VOLTS
5+ $250 $350 $450 $525 $600 $725 $850 $975 $1,000
1 $1,800 $2,250 $2,475 $2,750 $2,950 $3,375 $4,050 $4,900 $5,500
601-1000 (1)
2-4 $1,000 $1,225 $1.325 $1,475 $1,600 $1,800 $2,125 $2,550 $2,850
VOLTS
5+ $600 $750 $900 $1,000 $1,175 $1,350 $1,800 $2,450 $2,750
24
25
26
27
28
29